Benutzeranleitung / Produktwartung 3000/ITR des Produzenten Emerson
Zur Seite of 72
Precision Cooling For Business -Critic al C ontinuity™ Li eber t ® Ch al l enger ™ 3000/Li e ber t Chall e ng er ITR ™ wi t h Lieb er t i C OM ® Co nt r o l Operat ion & M aintenance Manua.
.
i T ABLE OF CONTENTS I MPORT ANT S AFETY I NSTRUCTION S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SA VE THE SE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ii 6.1 Standard Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 6.1.1 Change Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iii 7.6 Facility Fluid and Piping Maintenance for Water and Glycol Systems . . . . . . . . . . . . . . . . 49 7.7 Humidifier. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iv TA B L E S Table 1 Keyboard icons and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Table 2 Sample Liebert iCOM network configurations . . . . . . . . . . . . . . . . . . .
1 I MPORT A NT S AFETY I NSTRUCTIONS SA VE THESE INSTRUCTIONS This manual co ntains important safe ty instructions that sh ould be followe d during the installa tion and maintenance of the Liebert Ch allenger 3000/Liebert Ch allenger ITR with Liebert iCOM.
2 NOTICE Risk of leaking water. Can cause equi pment and building damage. This unit requires a water drain connection. It may also require an external water supply to operate. Improper installati on, application and serv ice practice can result in water leaking from the unit.
Introd uction 3 1.0 I NTRODUCTION 1.1 System Descriptions The Liebert Challenger 3000 ™ and Liebert Challenger ITR ™ Precision Cooling sy stems are available in several configurations. 1.1.1 Compressorized Systems These systems may be air, water, or g lycol cooled , depending on the he at re jection method selected.
Sta rt up 4 2.0 S TA R T U P Before beginning startup, make ce rtain that unit was installed accord ing to th e instructions in the installation manual , SL-11962. Verify that the fan shipping bolt has been removed, the check va lve has been installed (on air cooled units), and that th e scroll compressor is rota ting in the proper direc- tion.
Sta rt up 5 14. Check for unusual noises and vibration. 15. Check all refrigerant and fluid lines for leaks. 16. Test all functions of your unit for proper operation. 17. Close high voltage dead front cover and latch . 18. Close front accent panel and latch.
Operation with iC OM Control 6 3.0 O PERATION WITH I COM C ONTROL The Liebert iCOM ™ control offers the highest capabilities in unit control, co mmun ication and moni- toring of Liebert missio n-critical cooling units.
Liebert iCOM Displ ay Component s and Functions 7 4.0 L IEBERT I COM D ISPLAY C OMPONENT S AND F UNCTIONS The small an d the large displa y have a common k ey layout, as show n in Figure 2 . Figure 2 Liebert iCOM dis play component s NOTE The Help key may be pressed at any time for a brief explanation of what is being viewed.
Liebert iCOM Displ ay Component s and Functions 8 T able 1 Keyboard icons and fun ctions Icon Key Name Function On/Off Key Controls the operational state of the cooling unit. Alarm Key Silences an alarm. Help Key Accesses integrated help menus. ESCape Key Returns to the previous display view.
Liebert iCOM Displ ay Component s and Functions 9 Figure 3 Liebert iCOM de fault screen s ymbols 4.1 Navigating Through th e Liebert iCOM Display Liebert iCOM displays icons and text for monitori ng and controlling your Liebert cooling unit. The number of icons and amount of text shown depends on the display size.
Liebert iCOM Displ ay Component s and Functions 10 Figure 5 Liebert iCOM default home screen—Simple vie w 4.1.1 Control Interface—Three Main Menus The Liebert iCOM control has three main m enus: User, Service and Advanced. The User menu contains the most frequently used features, settings and status information.
Liebert iCOM Displ ay Component s and Functions 11 4.1.2 Accessing Menus and Settings Vie wi ng Da ta No password is required to view data or settings. To view data: 1. From the home screen, pres s the Enter key to view the User Menu (see Figure 8 ). 2.
Liebert iCOM Displ ay Component s and Functions 12 4.1.4 Accessing Submenus To access the User, Service or Advanced menu, pr ess the Enter or down arro w key while viewing the Status menu of the unit you wish to access. The User menu will b e displayed fi rst.
Liebert iCOM Displ ay Component s and Functions 13 Figure 7 Menu tree—Large an d small di splays, st and-alone o r networked Stat us M en u – Sys t em Vi ew ( Large D i spl ay O n l y ) St at us M.
Liebert iCOM Displ ay Component s and Functions 14 4.2 Changing Operational Settings Changes to the Liebert Challenger 3000/Liebert Challenger ITR’ s oper ation settings in the Set Alarms and Setpoints menus require a password. 1. From the home screen, pres s the Enter key to view the User Menu (see Figure 8 ).
Liebert iCOM Displ ay Component s and Functions 15 4.3 Changing Liebert iCOM’ s Display Settings No password is required to change the way Lieber t iCO M displays data. The Display Setup controls how the unit shows data, such as temperature, date and time.
Liebert iCOM Displ ay Component s and Functions 16 4.4 Graphical Dat a Record The Graphical Data Record charts the average temperature from th e return air te mperature sensor (see Figure 10 ). The temperature scales can be changed to expand or compress the data.
Liebert iCOM Displ ay Component s and Functions 17 4.6 Wiring for Unit-to- Unit Communications—U2U The Liebert Challenger 300 0/Liebert Challenger ITR with Liebert iCOM comes from the factory wired for stand-alone operati on. Multiple units can be set up in a network for efficiency, ease of operation and easier control.
Liebert iCOM Displ ay Component s and Functions 18 Large Displays A network switch is required to enable Ethernet communication on one or more cooling units with large displays. Ea ch cooling unit with a l arge displa y requires two straight-t hrough Ethernet cables from a network switch.
Liebert iCOM Displ ay Component s and Functions 19 Figure 12 U2U network setup diagram Net w o r k Swit ch Li eber t Chal l enger w it h S m all Li eb er t iC OM D is p la y Li eb er t Ch al l enger w.
Liebert iCOM Displ ay Component s and Functions 20 Notes on Wiring for a U2U Network—Refer to Figures 13 and 15 1. See unit electrical sche matic. 2.
Liebert iCOM Displ ay Component s and Functions 21 Figure 13 Liebert iCOM wir ing—Unit as shipped Liebert I nt elliSlot Power Supply Liebert I nt elliSlo t 1 Liebert I nt elliSlo t 2 P64 A Connec t .
Liebert iCOM Displ ay Component s and Functions 22 Figure 14 Wiring a small display for U2U network operation Standard Small Graphics Display (Rear V iew) Liebert iCOM I/O Board Straight-Through Ether.
Liebert iCOM Displ ay Component s and Functions 23 Figure 15 Wiring a large display for U2U network oper ation Crossover Coupler (See Note 6) Red Crossover Ethernet Cable Liebert iCOM I/O Board Straig.
Liebert iCOM Displ ay Component s and Functions 24 Figure 16 Liebert iCOM inpu t-output control b oard P65 P64 (RJ-45 Jack) P66 P63 P61 P67.
Liebert iCOM Displ ay Component s and Functions 25 4.7 Entering Network Setup Information Setting up a U2U network requires setting a unique IP add resses for each unit, choosi ng a U2U address and designating the U2 U group.
Liebert iCOM Displ ay Component s and Functions 26 4.8 Viewing Multiple Unit s wi th a Networked Large Display When you first wake up the control, press the ESC key to return to the System view Status menu. This view shows an average of all the units on the network and any alarms present.
Operation 27 5.0 O PERATION The Liebert iCOM display for yo ur Liebert cooling unit features an easy-to-use , menu -driven liquid crystal display (LCD). All unit settings and parame ters can be viewed and adjusted through three menus: User, Service and Adva nced.
Operation 28 Autorest art When there is a loss of power to the cooling unit an d power comes back, the u nit will return to its pre- vious operating status—On if it was On befo re the power fail ed, Off if it was Off.
Operation 29 Pump Down—Air Cooled with Condenser Only Unit s The Pump Down operation is performed to protect the compressor oil from being diluted with l iquid refrigerant, which helps ensure that the compressor is properly lubr icated for the next startup.
Operation 30 Evaluate the start op eration of the unit (with pump down). 1. Close LLSV 2. Wait for L PS to make or ignore for WSK time If LPS is made before WSK has expired, allow the comp ressor to continue running, if not then stop compressor and alarm low pressure alarm.
Operation 31 5.2.3 Intelligent Control (Chilled W ater Only) The intellig ent control operates from a set of general rules that define h ow the control output should be adjusted for different system conditions. Th e rules are designed to dupli cate the actions that an experienced human operator would take if manually controll ing the system.
Alarm Descriptions 32 6.0 A LARM D ESCRIPTIONS The Liebert iCOM will audibly and visual ly annunciate all enabl ed alarms. Alarms are wired from Terminal 24 through a normally open contact to loca tions 50 , 51, 55 and 56, r espectively, for alarms 1 through 4.
Alarm Descriptions 33 6.1.3 High Head Pressure Compressor high he ad is monitored with a pressure switch. One SPDT pressure switch is used for the compressor in the unit. If head pressure exceeds 36 0 PSIG, the switch op ens the compressor contactor and sends an input signal to the control .
Alarm Descriptions 34 6.1.9 Loss of Air Flow A differential air pressure swi tch is used to indi cate loss of air flow in Liebert Challenger 3000/Lie- bert Challeng er ITR units. Check for blockage of unit air outlet or inlet. C h eck blower motor fuses and over load reset.
Alarm Descriptions 35 6.2 Optional Alarms 6.2.1 Loss of W ater Flow Available onl y with 3-way valves an d occurs when no water flow is detected in the chilled water or condenser water supply line. An op tional flow sw itch is required for this al arm.
Componen t Operatio n and Maintenance 36 7.0 C OMPONENT O PERATION AND M AINTENANCE 7.1 System T esting 7.1.1 Environment al Control Functions The performance of all control circuit s can be tested by actuating each of the main functions. This is done by temporarily ch anging the setpoints.
Componen t Operatio n and Maintenance 37 Control T ransformer and Fuses The control system is divided into four separate ci rcuits. The control voltage circuits are individually protected by fuses located o n the transforme r/fuse bo ard. If any of the fuses are blown, first eliminate shorts, then use spare fuses supplied with unit.
Componen t Operatio n and Maintenance 38 Figure 22 Recommended liquid sensor lo cations The zone leak detection kit provides leak detection for a defined zon e. This kit is ideal for perimeter sensing or serpentine coverage of small areas. A simple, two-wire co nnection signals the alarms at a Liebert envi ronmental unit or at a monitoring p ane l.
Componen t Operatio n and Maintenance 39 7.2 Filters Filters are usually the most neglected item in an environmental control system . To maintain efficient operation, they should be checked monthly and ch anged as required.
Componen t Operatio n and Maintenance 40 7.3.3 Air Distribution All unit models are designed f or constant volume air delivery. Therefore an y unusual restrictions within the air circuit must be avoided. For downflow models operating on a raised floor, refer to the following table for recomme nded free area for proper air flow.
Componen t Operatio n and Maintenance 41 7.4.2 Discharge Pressure Discharge Pressure can be increased or decreased by load conditions or condenser effi ciency. The high pressure switch will shut the compressor down at it s cut-out setting. Refer to Table 7 , below.
Componen t Operatio n and Maintenance 42 7.4.5 Hot Gas Byp ass V alve—Not A vailable on Digit al Scroll Unit s Operation—Self-Cont ained Units The hot gas bypass is inserted between the compressor discharge li ne and the leaving side of the expansion valve through the side outlet distributo r.
Componen t Operatio n and Maintenance 43 Checking Refrigerant Charge (Lee–T emp / Flood Back Head Pressure Control) The system refrigerant level must be che cked periodically. To do so: 1. Adjust temperature setpoint in the unit so that the compressor wi ll run continuously.
Componen t Operatio n and Maintenance 44 7.4.8 Motorized Ball V alve—Digit al Scroll Compressor On water-coo led and glycol-cooled digital scroll unit s, the dis charge pressure is controlled by a motor- ized ball valve.
Componen t Operatio n and Maintenance 45 To raise the head pressure setting, turn the adju sting screw counterclockwise until the desired set- ting is obtained. Figure 24 Johnson Controls valve adjustment Manual Flushing —The valve may be fl ushed by insertin g a screwdriver or similar tool under the two sides of the main spring and lifti ng.
Componen t Operatio n and Maintenance 46 Manual Flushing —The valve may be fl ushed by rotating the socket head screw clockwise. This screw must be in the OUT position (counterclockwise) for norm al valve opera tion. Valve Disass embly 1. Shut off the water supply by using isolatin g valves.
Componen t Operatio n and Maintenance 47 7.4.1 1 Compressor Oil NOTICE Risk of improper compressor lubrication. Can cause compressor and refrigerant system damage. Failure to use oil types, viscosities an d quantities recommended by the compressor manufacturer may reduce comp ressor life and void the comp ressor warranty.
Componen t Operatio n and Maintenance 48 7.5.2 St andard Scroll Compressor Replacement Infrequently a fault in the motor insulation may resu lt in a motor burn, but bu rnouts rarely occur in a properly installe d system.
Componen t Operatio n and Maintenance 49 Three-phase power must be connected to the unit line voltage term inals in the proper sequence so that the scroll comp ressor rotates in the proper di rection. Rotation in the wrong direction will result in poor performance and compressor damage.
Componen t Operatio n and Maintenance 50 7.7 Humidifier 7.7.1 Infrared Humidifier During normal humid ifier operation, deposits of mineral solid s will collect in the humidifier pan. This should be cleaned out periodica lly to ensure efficient operation.
Componen t Operatio n and Maintenance 51 Changing Humidifier Lamp s 1. Open disconne ct switch. 2. Open front panel. 3. Remove screws securing li ne voltage compartment cove r, then remove the cover. 4. In li ne voltage compartment, disc onnect one end of the purple jump ers, then locate the burned out bulb with a continuity meter.
Componen t Operatio n and Maintenance 52 Autoflush Controls Use the LCD display, menu, and ke ys on the front control panel to program the autoflush controls. 7.7.2 Steam Ge nerating Humidifier Steam generati ng humidifiers ar e designed to operate in voltage ranges f rom 200 to 575 volts and generate 11 p ounds (5 kg) of steam per hour.
Componen t Operatio n and Maintenance 53 Operation 1. During startup, when the humidi ty control calls for hu midification, the fill valve opens and allows water to enter the canister. When the water level reaches the el ectrodes, current flows and the water begins to warm.
Componen t Operatio n and Maintenance 54 Replacing the Canister Over a period of operation, the humidifier electrodes become coated with mineral solids. This co ating insulates the electrodes and decre ases the current flow. To mainta in humidifier capacity , the water level slowly rises to expose fresh electrode.
Componen t Operatio n and Maintenance 55 Circuit Board Adjustment s Humidifier operation is governed by the humidi fier control board. Th is board is locat ed on the right side of the hu midifier compartment. There are three potentiome ters mounted on the board.
Trou bleshoot ing 56 8.0 T ROUBLESHOOTING Use this section to a ssist in troubleshooting yo ur unit. Also refer to 6.0 - Alarm Descriptions . Sug- gestions are grouped by product function for convenience. NOTICE Risk of improper control connec tion. Can cause equip ment damage.
Trou bleshoot ing 57 T able 14 Compressor and refrige ration system trouble shooting Symptom Possible Cause Check or Remedy Compressor will not start Power Off Check main switch, fuses or CBs and wiring Current overload open Re-set units with overload option manually.
Trou bleshoot ing 58 Flooding Defective or i mproperly set expansion valve Increase superheat or replace valve Evaporator fan motor or belt Correct problem or replace fan mo tor and/ or belts.
Trou bleshoot ing 59 T able 15 Dehumidification tro ubleshooting Symptom Possible Cause Check or Remedy No dehumidification Control not ca lling for dehumi dific ation Check monitor status. Compressor contactor n ot pulling in See 7.5.1 - Compressor Functional Check and Ta ble 14 .
Trou bleshoot ing 60 T able 18 Steam gen erating humidifier troubleshooting Symptom Possible Cause Check or Remedy False canister full indicatio n Foaming Check drain valve to ensure that it drain s freely. Check and replace if defective. Check water supply.
Trou bleshoot ing 61 Excessive arcing in the canister Drain valve clogged or defective Verify that drain valve operates freely when activated. Clean valve and replace coil or valve if defective. Flush canister several times and replace if arcing persists.
Monthly Maintenance Inspection Checklist 62 9.0 M ONTHLY M AINTENANCE I NSPECTION C HECKLIST Date:___________ _____________________ _______ Prepared by:__ ________________________ _______ Model #:_____________ ________________________ Serial #:_____ _________________________ ______ Filters ___ 1.
Semiannual Maintenance In spection Checklist 63 10.0 S EMIANNUAL M AINTENANCE I NSPECTION C HECKLIST Date:___________ _____________________ ________ Pre pared by:____________ _____________________ Model #:_____________ ________________________ Serial #:_____ _________________________ _______ Filters ___ 1.
Semiannual Maintenance In spection Checklist 64.
.
Ensuring The Hi gh A vai lab ilit y Of Mission-Critic al Dat a And App lic ations. Emerson Net work P ower , the global leader in enabling business-critical continuity , ensures network re siliency an.
Ein wichtiger Punkt beim Kauf des Geräts Emerson 3000/ITR (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Emerson 3000/ITR noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Emerson 3000/ITR - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Emerson 3000/ITR reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Emerson 3000/ITR erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Emerson 3000/ITR besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Emerson 3000/ITR verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Emerson 3000/ITR. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Emerson 3000/ITR gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
