Benutzeranleitung / Produktwartung SRM - 410U des Produzenten Echo
Zur Seite of 36
W ARNING Read rules for safe operation and instructions carefully . ECHO provides an Operator's Manual and a Safety Manual. Both must be read and understood for proper and safe operation.
2 Copyright© 2009 By Echo, Incorporated All Rights Reserved. I n t r o d u c t I o n W elcome to the ECHO family . This ECHO product was designed and manufactured to provide long life and on-the-job dependability . Read and understand this manual and the SAFETY MANUAL you found in the same package.
G r a s s T r i m m e r /B r u s h C u T T e r O p e r a T O r ' s m a n u a l 3 I n t e r n a t I o n a l s y m b o l s s a f e t y m a n u a l s a f e t y s y m b o l s a n d I m p o r t a n t .
4 Physical Condition Y our judgment and physical dexterity may not be good: • if you are tired or sick, • if you are taking medication, • if you have taken alcohol or drugs. Operate unit only if you are physically and mentally well. Eye Protection W ear eye protection that meets ANSI Z87.
G r a s s T r i m m e r /B r u s h C u T T e r O p e r a T O r ' s m a n u a l 5 DANGER Do not operate this product indoors or in inadequately ventilated areas.
6 e q u I p m e n t W ARNING Use only ECHO approved attachments. Serious injury may result from the use of a non-approved attachment com- bination. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which have not been tested and approved by ECHO.
G r a s s T r i m m e r /B r u s h C u T T e r O p e r a T O r ' s m a n u a l 7 P/N 89016054130 P/N X505002310 Hot Decal (near mufer) d e s c r I p t I o n Locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the instruc- tions on them.
8 1. POWER HEAD - Includes the Engine, Clutch, Fuel System, Ignition System and Recoil Starter . 2. THROTTLE TRIGGER LOCKOUT - This lever must be held during starting. Operation of the throttle trigger is prevented unless throttle trigger lockout lever is engaged.
G r a s s T r i m m e r /B r u s h C u T T e r O p e r a T O r ' s m a n u a l 9 c o n t e n t s The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, shield installation and other assembly may be necessary .
10 a s s e m b l y d r I v e s h a f t / p o w e r h e a d T ools Required: 4 mm Hex W rench Parts Required: Power Head, Drive Shaft Assembly 1. Stand power head upright on a level surface. 2. Loosen the drive shaft clamp bolt (A) at engine drive shaft clamp, and remove drive shaft locating bolt (B).
G r a s s T r i m m e r /B r u s h C u T T e r O p e r a T O r ' s m a n u a l 11 1. Align hole in upper plate (D) with notch in gear housing (E), and insert locking tool to prevent splined shaft from turning. Arrow on gear housing ange points to notch location.
12 A B C u - h a n d l e I n s t a l l a t I o n T ools Requir ed : 17 & 19 mm wrench, 4 mm hex wrench Parts Requir ed: U-Handle, Clamp w/screws, 8 mm x 55 mm hex bolt, 8 mm at washer 1.
G r a s s T r i m m e r /B r u s h C u T T e r O p e r a T O r ' s m a n u a l 13 6. Secure the right hand U-handle by tightening 4 right handle assem- bling bolts (H) loosely . 7. Adjust handles for comfortable operation and tighten handle as- sembling bolt (E) and 4 right handle assembling bolts (H).
14 o p t I o n a l n y l o n h e a d I n s t a l l a t I o n T ools Requir ed: Locking T ool Parts Requir ed: Nylon Line Head. 1. Align hole in upper plate with notch in gear housing, and insert locking tool to prevent splined shaft from turning.
G r a s s T r i m m e r /B r u s h C u T T e r O p e r a T O r ' s m a n u a l 15 2.REPLACING SPOOL NOTE Keep line tight on spool. A. Snap spool into housing while pulling line through eyelets with about 15 cm (6 in) extending out. CAUTION Knob tightens counterclockwise, “left”.
16 o p e r a t I o n W ARNING Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit.
G r a s s T r i m m e r /B r u s h C u T T e r O p e r a T O r ' s m a n u a l 17 Plastic/Nylon Grass/W eed Blades may be used where ever the nylon line head is used. DO NOT use this blade for heavy weeds or brush! 8 T ooth W eed/Grass Blade is designed for grass, garden debris and thick weeds.
18 f u e l NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor performance, or severe engine damage and void the product warranty . Read and follow instructions in the Storage section of this manual.
G r a s s T r i m m e r /B r u s h C u T T e r O p e r a T O r ' s m a n u a l 19 Mixing Instructions 1. Fill an approved fuel container with half of the required amount of gasoline. 2. Add the proper amount of 2-stroke oil to gasoline. 3. Close container and shake to mix oil with gasoline.
20 s t a r t I n g c o l d e n g I n e W ARNING When engine is started, conrm that there is not any abnormal vibration or sound. If there is abnormal vibration or sound, ask your DEALER to repair . After refueling tighten fuel cap rmly and check for leakage.
G r a s s T r i m m e r /B r u s h C u T T e r O p e r a T O r ' s m a n u a l 21 s t a r t I n g w a r m e n g I n e 1. Press the decompression device (E). 2. Stop Switch Move stop switch button (A) forward away from the STOP posi- tion. 3. Pur ge Bulb Pump purge bulb (C) until fuel is visible in the "Clear" fuel return line.
22 m a I n t e n a n c e W ARNING Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit.
G r a s s T r i m m e r /B r u s h C u T T e r O p e r a T O r ' s m a n u a l 23 B A a I r f I l t e r Level 1. T ools r equir ed: 25 - 50mm (1 - 2 in.) cleaning brush Parts r equir ed: REPOWER TM T une-Up Kit NOTE Always brush dirt and debris away from air cleaner area prior to cleaning air lter .
24 f u e l f I l t e r Level 1 . T ools r equir ed: 200- 250 mm (8 - 10 in.) length of wire with one end bent into a hook, clean rag, funnel, and an approved fuel container . Parts r equir ed: REPOWER TM T une-Up Kit DANGER Fuel is VER Y ammable. Use extreme care when mixing, storing or handling.
G r a s s T r i m m e r /B r u s h C u T T e r O p e r a T O r ' s m a n u a l 25 c o o l I n g s y s t e m Level 2. T ools r equir ed: Air compressor and safety nozzle, or: 4 mm Hex wrench, 25 - 50 mm (1 - 2 in.) cleaning brush. Parts Requir ed: None.
26 Exhaust Port Cleaning Level 2. T ools required: 4 & 5 mm Hex W rench, W ood or plastic scraper Parts Required: As needed: Heat Shield 1. Remove spark plug lead from spark plug, and remove mufer cover (2 screws). 2. Place piston at top dead center .
G r a s s T r i m m e r /B r u s h C u T T e r O p e r a T O r ' s m a n u a l 27 CAUTION When starting, idling adjustment speed should be adjusted not to rotate the cutting attachment. Correct idle speed is adjusted 2300 to 2700 r/min. Or 1/4 turn CCW from the point the cutting attachment stops moving.
28 l u b r I c a t I o n Level 1. T ools Requir ed: 8 & 13 mm Open End W rench, Screwdriver , Clean Rag. Parts Requir ed: POWER BLENDX TM 8 oz. (P/N 91014) or Lithium Base Grease. Gear Housing 1. Clean all loose debris from gear box. 2. Remove plug (A) and check level of grease.
G r a s s T r i m m e r /B r u s h C u T T e r O p e r a T O r ' s m a n u a l 29 s h a r p e n I n g m e t a l b l a d e s Three styles of metal blades are approved for use on the ECHO Brush Cutter . The 8-tooth blade can be sharpened during normal mainte- nance.
30 DANGER Fuel vapors are extremely ammable and may cause re and/or explosion. Never test for ignition spark by ground- ing spark plug near cylinder plug hole, otherwise serious personal injury may result.
G r a s s T r i m m e r /B r u s h C u T T e r O p e r a T O r ' s m a n u a l 31 DANGER Do not store in enclosure where fuel fumes may accumulate or reach an open ame or spark. s t o r a g e W ARNING During operation the mufer or catalytic mufer and surrounding cover become hot.
32 s p e c I f I c a t I o n s MODEL ---------------------------------------------------- SRM-410U Length ------------------------------------------------------- 1860 mm (73.2 in.) W idth -------------------------------------------------------- 630 mm (24.
G r a s s T r i m m e r /B r u s h C u T T e r O p e r a T O r ' s m a n u a l 33 n o t e s.
34 n o t e s.
G r a s s T r i m m e r /B r u s h C u T T e r O p e r a T O r ' s m a n u a l 35 n o t e s.
ECHO, INCORPORA TED 400 O a k w O O d R O a d L a k e Z u R i c h , iL 60047-1564 7-2 SUEHIROCHO 1-CHOME, OHME, T OKYO, 198-871 1, JAP AN PHONE: 81-428-32-61 18 F AX: 81-428-32-6145 GB © 2009 S054030.
Ein wichtiger Punkt beim Kauf des Geräts Echo SRM - 410U (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Echo SRM - 410U noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Echo SRM - 410U - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Echo SRM - 410U reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Echo SRM - 410U erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Echo SRM - 410U besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Echo SRM - 410U verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Echo SRM - 410U. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Echo SRM - 410U gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
