Benutzeranleitung / Produktwartung CS-450P des Produzenten Echo
Zur Seite of 30
CS-450P ECHO POWER EQUIPMENT (CANADA) 501 Newbold Street, London, Ontario Canada N6E 1K4 W ARNING Read the instructions carefully and follow the rules for safe operation.
2 CS-450P Copyright © 2009 All Rights Reserved. 1. Fatigue causes carelessness. Be more cautious before rest periods and before the end of your shift.
3 CS-450P WARNING The safety alert symbol accompanied by the word “WARNING” calls attention to an act or condition which CAN lead to serious personal injury or death if not avoided. CIRCLE AND SLASH SYMBOL This symbol means the specific action shown is prohibited.
4 CS-450P Carburetor adjustment - Idle speed Carburetor adjustment - High speed mixture Carefully read the operator’s manual Wear eyes, ears and head protection Carburetor adjustment - Low speed mix.
5 CS-450P P A CKING LIST The ECHO product you purchased has been f actor y pre-assembled f or your con v enience. Due to packaging restrictions, guide bar and saw chain installation and other assembly ma y be necessary . After opening the car ton, check f or damage.
6 CS-450P NOMENCLA TURE OF P ART S 24 16 17 18 20 19 15 5 4 8 10 11 12 13 14 3 2 1 X505-000460 X505-000450 X503-009740 9 21 22 23 X524-002280 ATTENTION Pour un travail en sécurité, respectez toutes les règles de sécurité et les indications du manuel d’utilisation.
7 CS-450P NOMENCLA TURE OF P AR TS 1. Operator’s manual - Included with unit. Read before operation and keep for future reference to learn proper, safe operating techniques. 2. Safety manual - Describe operating and safety instructions for this chain saw.
8 CS-450P VIBRA TION AND COLD • It is belie v ed that a condition called Raynaud’ s Phenomenon, which affects the fingers of certain individuals, ma y be brought about by e xposure to vibration and cold. Exposure to vibration and cold ma y cause tingling and burning f ollow ed by loss of color and numbness in the fingers .
9 CS-450P SP ARK ARREST OR MUFFLER • The spark arrestor muffler controls the e xhaust noise and prev ents hot, glowing par ticles of carbon from leaving the muffler . Make sure the spark arrestor screen is in good repair and properly seated in the muffler .
10 CS-450P WARNING Saw chain is sharp! Always wear gloves when handling assembly, otherwise serious personal injury may result. GUIDE B AR AND SA W CHAIN INST ALLA TION/REMO V AL NOTE • Move the chain brake lever (Front hand guard) fully rearward to remove or install the clutch cover to chain saw.
11 CS-450P Adjusting screw Direction to tension the chain Proper tension Improper tension 7. T urn saw ov er , and check brak e band f or correct position on clutch drum. If brake band is not in place around drum, remove co v er , make sure brak e is unlock ed, and reinstall.
12 CS-450P FUEL AND LUBRICANT FUEL ST A TEMENT GASOLINE - Use 89 Octane [(R+M)/2] (mid grade or higher) gasoline or gasohol known to be good quality . Gasohol may contain up to 10 % Eth yl (grain) alcohol or 15 % MTBE (methyl teriary-butyl ether). Gasohol containing methyl (w ood) alcohol is NO T approv ed.
13 CS-450P HANDLING FUEL MIXING INSTRUCTIONS - 1. Fill an approv ed fuel container with half of the required amount of gasoline. 2. Add the proper amount of two-strok e oil to gasoline. 3. Close container and shake to mix oil with gasoline. 4. Add remaining gasoline, close fuel container , and remix.
14 CS-450P Oil tank cap Fuel tank cap Cap indication Fuel/oil tanks are indicated by the following illustrations. CHAIN LUBRICANT Proper lubrication of the chain while in operation reduces friction between the chain and the guide bar to a minimum and assures a longer service life .
15 CS-450P WHEN THE ENGINE IS COLD CAUTION Make sure the bar and chain are free from any obstruction when starting the chain saw. • Mov e chain brak e le ver fully f orw ard to lock chain brak e before starting. • Fill the fuel tank with fuel mixture.
16 CS-450P STOP Ignition switch Throttle trigger Unlock chain brake R UNNING • When engine star ts, k eep idling for a f ew minutes . • Set the brak e lev er in the unlock ed position bef ore star ting to cut. • Pull throttle trigger gradually and increase re volution of the engine .
17 CS-450P CUTTING INSTR UCTION GENERAL CAUTION • Read the ECHO “CHAIN SAW SAFETY MANUAL” included with your chain saw for additional cutting and safety instructions. • Wear suitable hearing protection such as earmuffs or earplugs to protect against objectionable or uncomfortable loud noises.
18 CS-450P FELLING THE TREE A f alling tree can seriously damage anything it ma y hit - a car , a house, a f ence, a po wer-line, or another tree. There are wa ys to make a tree f all where you w ant it, so first decide where that is! Bef ore cutting, clear the area around the tree.
19 CS-450P LIMBING Limbing a fallen tree is m uch the same as b ucking. Ne ver stand on the tree that y ou are limbing. When limbing, caution is the word. Be careful of the tip touching other limbs. Alwa ys use both hands . Don’t cut with the saw o verhead or aligned vertically with your body .
20 CS-450P CHAIN BRAKE OPERA TION • Set the lev er in the unlock ed position before star ting to cut. • If the brake is tripped by kickbac k reaction, the chain will stop immediately . Release the throttle to av oid possible damage to the engine or clutch.
21 CS-450P A UT OMA TIC CHAIN BRAKE Kickbac k produced from the tip of the guide bar will trip the automatic chain brake . T o mak e sure that the automatic chain brake oper ates proper ly , follow these steps: 1. Stop the engine. 2. Hold the saw with the guide bar appro ximately 50 cm abov e a wooden surf ace.
22 CS-450P CHAIN AND GUIDE B AR COMBINA TION The f ollowing combinations are recommended to the model CS-450P . GUIDE B AR (Low-kic kback) Replacement guide bars.
23 CS-450P MAINTENANCE AND CARE Y our ECHO chain saw is designed to pro vide many hours of trouble free service. Regular scheduled maintenance will help your chain sa w achiev e that goal. If you are unsure or are not equipped with the necessar y tools, y ou ma y want to tak e your unit to an ECHO Ser vice Dealer for maintenance .
24 CS-450P CARBURET OR ADJUSTMENT Every unit is run at the factory and the carburetor is set in compliance with Emission Regulations. In addition, the carburetor is equipped with “H” (High Speed) and “L ” (Low Speed) needle adjustment limiters that pre vent settings outside acceptab le limits.
25 CS-450P 0.6 to 0.7 mm Oil filter Fuel filter Oil tank cap Fuel tank cap Cleaner cover knob Spark plug Air cleaner cover Air filter Cylinder cover Air filter cover AIR FIL TER • Check bef ore ev er y use. • Loosen cleaner cover knob and remov e air cleaner cov er and filter .
26 CS-450P Worn : 0.5 mm Groove Oil hole Cylinder fins Spark arrestor screen Muffler Screen cover Adjusting screw Decrease Increase Clutch (Sprocket) Gasket GUIDE B AR • Clean before using. - Clean the groove of the guide bar with a small screwdriv er .
27 CS-450P SETTING THE SA W CHAIN Impor tant points for proper maintenance of sa w chain: • K eep the cutters shar p at all times. • K eep the left and the r ight cutters properly aligned. - Note that b lunt or irregular cutters will result in poor cutting performance, increased vibration of chains and premature breakage of the saw chain.
28 CS-450P 1/5 One fifth of file diameter remains above cutter edge Side plate angle Top plate filing angle 60° 25° Parallel 0.64 mm (0.025 in.) Top plate cutting angle Depth gauge 60° Remove until flat with tool Depth gauge tool Round off the edge NOTE These angles are referred to as Oregon 20LPX.
29 CS-450P TR OUBLESHOO TING WARNING Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark by grounding spark plug near cylinder plug hole, otherwise serious personal injury may result.
30 CS-450P MODEL CS-450P Dimension L × W × H mm 400 × 252 × 278 Mass Power head, dry kg 5.1 Without chain and guide bar Engine Type A ir-cooled two-stroke single cylinder Displacement mL (cm³) 45 .
Ein wichtiger Punkt beim Kauf des Geräts Echo CS-450P (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Echo CS-450P noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Echo CS-450P - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Echo CS-450P reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Echo CS-450P erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Echo CS-450P besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Echo CS-450P verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Echo CS-450P. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Echo CS-450P gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
