Benutzeranleitung / Produktwartung FISHMARK 640C des Produzenten Eagle
Zur Seite of 108
Pub. 988-0143-861 www.eaglesonar.com Fish-Finding & Depth-Sounding Sonars Installation and Operation Instructions.
Copyright © 2005 LEI-Eagle All rights reserved. Eagle ® , FishMark ® and SeaFinder ® are registered trademarks of LEI No part of this manual may be copied, reproduced, republished, transmitted or distributed for any purpose, without prior written consent of Eagle Electronics.
i Table of Contents Read Me First! ................................................................................... 1 Capabilities and Specifications: FishMark ® 640c .............................. 2 SeaFinder ® 640c DF ..........................
ii Main Menu ......................................................................................... 39 Pages .................................................................................................. 40 Basic Sonar Quick Reference .........
iii To turn off HyperScroll .................................................................. 74 Pop-up Help ........................................................................................ 74 Reset Options ...................................
iv Notes.
1 Section 1: Read Me First! How this manual can get you out on the water, fast! Welcome to the exciting world of digital sonar! We know you're anxious to begin finding fish, but we have a favor to ask.
2 any longer, turn to the Quick Reference on page 45 and head for the water with your sonar unit!) After you have gained some experience with your sonar, you'll want to check out Section 4, which explains more advanced Sonar Options and Other Features .
3 Back-up memory: .......... Built-in memory stores sonar settings for decades. Languages: ...................... 10; menu languages selectable by user. Sonar Frequency: ...................... 50/200 kHz for SeaFinder 640c DF ; 200 kHz for FishMark 640c .
4 Surface water temp: ..... Yes. Speed/distance log: ....... Optional (requires optional speed sensor). NOTICE! The storage temperature range for your unit is from -4 degrees to +167 degrees Fahrenheit (-20 degrees to +75 degrees Celsius).
5 How to Use this Manual: Typographical Conventions Many instructions are listed as numbered steps. The keypad and arrow "keystrokes" appear as boldface type. So, if you're in a real hurry (or just need a reminder), you can skim the instructions and pick out what menu command to use by finding the boldface command text.
6 For example, instructions for turning on the Fish ID feature would look like this: 1. From the Sonar Page, press MENU | ↓ to S ONAR F EATURES | ENT . 2. Press → or → ↓ to F ISH ID S YMBOLS | ENT | EXIT | EXIT . Translated into complete English, step 1 above would mean: "Start on the Sonar Page.
7 Section 2: Installation & Accessories Preparations You can install the sonar system in some other order if you prefer, but we recommend this installation sequence: Caution: You should read over this entire installation section before drill- ing any holes in your vessel! 1.
8 adjustable strap. These are "kick-up" mounting brackets. They help prevent damage if the transducer strikes an object while the boat is moving. If the transducer does "kick-up" the bracket can easily be pushed back into place without tools.
9 grit sandpaper, specially formulated epoxy adhesive available from LEI (see ordering information on the inside portion of the back cover). A sandwich hull also requires polyester resin. Selecting a Transducer Location 1. The location must be in the water at all times, at all operating speeds.
10 5. If possible, route the transducer cable away from other wiring on the boat. Electrical noise from engine wiring, bilge pumps and aerators can be displayed on the sonar's screen. Use caution when routing the trans- ducer cable around these wires.
11 However, there are times when you may need to adjust the transducer slightly higher or lower. The slots in the mounting brackets allow you to loosen the screws and slide the transducer up or down. If you fre- quently lose bottom signal lock while running at high speed the trans- ducer may be coming out of the water as you cross waves or wakes.
12 Lack of angle adjustment can be particularly troublesome on hulls that sit with the bow high when at rest or at slow trolling speeds. Third, a transducer CAN NOT shoot through wood and metal hulls. Those hulls require either a transom mount or a thru-hull installation.
13 Align plastic ratchets in bracket. B. Two-piece bracket: Locate the four plastic ratchets in the trans- ducer's hardware package. Press two ra tchets into the sides of the plastic bracket and two on either side of th e transducer as shown in the follow- ing illustrations.
14 Add ratchets to bracket and transducer. 2. Aligning the transducer on the transom. A. One-piece bracket: Slide the transducer between the two ratch- ets.
15 Insert bolt and check transducer position on transom. B. Two-piece bracket: Assemble the transducer and bracket as shown in the following figure. Temp orarily slide the bolt though the transducer assembly but don't tighte n the nut at this time.
16 Assemble transducer and bracket. 3. Assembling the transducer. A. One-piece bracket: Once you determine the correct position for the ratchets, assemble the transducer as shown in the following figure. Don't tighten the lock nut at this time. Assemble transducer and bracket.
17 Mark the center of each slot for the mounting screw pilot holes. You will drill one hole in the center of each slot. Drill the holes. For the one-piece bracket, use the #29 bit (for the #10 screws). For the two-piece bracket, use the #20 bit (for the #12 screws).
18 tighten the lock nut! If you do, the transducer won't "kick-up" if it strikes an object in the water. Align transducer centerline with hull bottom and attach transducer to transom. Rear view of dual-frequency Skimmer shown. 6. Route the transducer cable throug h or over the transom to the sonar unit.
19 Caution: If you drill a hole in the transom for the cable, make sure it is lo- cated above the waterline. After installation, be sure to seal the hole with the same marine grade above- or below-waterline seal- ant used for the mounting screws. 7. Make a test run to determine the results.
20 Transducer mounted on trolling motor, side view. Transducer Orientation and Fish Arches If you do not get good fish arches on your display, it could be because the transducer is not parallel with the ground when the boat is at rest in the water or at slow trolling speeds.
21 If the arch slopes up – but not back down – then the front of the trans- ducer is too high and needs to be lowered. If only the back half of the arch is printed, then the nose of the transducer is angled too far down and needs to be raised. NOTE: Periodically wash the transducer's face with soap and water to re- move any oil film.
22 For example, some (but not all) ma nufacturers use a layer of fiberglass, then a core of balsa wood, finishing wi th an outer layer of fiberglass. Re- moving the inner layer of fiberglass an d the balsa wood core exposes the outer layer of fiberglass.
23 harder (more rocky) the bottom, the easier it will be to get a second bot- tom signal. Don't touch the controls once they've been set. Example of a second bottom signal. Unit is in 30 feet of water, with range set at 80 feet and sensitivity set at 87 percent 2.
24 4 . Most people can get good results by following steps 1 through 3, so this step is optional . If you want to make an extr a effort to be absolutely sure that your selected location will work under all conditions, make a test run with the boat on plane and observe th e bottom signal.
25 Epoxy transducer to hull. WARNING: Use only the epoxy available from LEI. It has been for- mulated to work with these installation procedures. Other epoxy types may be too thin or may not cure to the right consistency for optimum transducer performance.
26 3. Press the transducer into the epoxy, twisting and turning it to force any air bubbles out from under the transducer face. Stop pressing when you bottom out on the hull. When you're finished, the face of the trans- ducer should be parallel with the hull, with a minimum amount of ep- oxy between the hull and transducer.
27 Sonar unit with external temp sensor, external speed sensor, or combo speed/temp sensor. The primary temperature sensor is built into the transducer. Optional Speed Sensor Installation All the units in this series can display speed and distance traveled, but only the SeaFinder 640c DF comes packed with a speed sensor.
28 Recommended tools for this job include: dr ill, 5/8" drill bit, 1/8" drill bit for pilot holes, screwdriver. Required su pplies for this job include: four #8 stainless steel wood screws (3/4" long), high quality, marine grade above- or below-waterline caulking compound.
29 Speed sensor mounting configuration: side view (left) and rear view (right.) Route the sensor's cable through or over the transom to the sonar unit. If you need to drill a hole in the transom to pass the connector through, the required hole size is 5/8".
30 Caution: When using the unit in a saltwa ter environment, we strongly rec- ommend that you shut off the pow er supply to the power cable when the unit is not in use. When the unit is turned off but still connected to a power supply, electrolysis ca n occur in the power cable plug.
31 Power connections for the sonar unit. WARNING: Do not use this product without a 3-amp fuse wired into the power cable! Failure to use a 3-amp fuse will void your warranty. This product must be independently fused with the enclosed 3-amp fuse (or equivalent), even if you connect to a fused accessory or power buss.
32 Bracket Installation Mount the unit in any convenient location, provided there is clearance behind the unit when it's tilted for the best viewing angle. You should also make sure there is enough room behind the unit to attach the power and transducer cables.
33 sure to leave enough slack in the cables to allow tilting or swiveling the unit. If you choose to fill in the hole, be sure to position the cables against the rear edge of the hole as you apply the fill material. Front view (left) and side view (right) showing dimensions of the sonar unit when mounted on gimbal bracket.
34 In-Dash Installation You can mount the unit in the dash with an optional FM-5 In-Dash Adapter Kit. The kit includes mounting hardware, a template for cut- ting the hole and an instruction sheet, part 988-0147-43. In-dash mounting template for the sonar unit, showing dimensions.
35 The portable power pack can be used with eight "D" cell alkaline bat- teries or an optional sealed, rechargeable battery. For set-up directions, refer to the pack's instruction sheet.
36 Notes.
37 Basic Sonar Operation This section addresses the unit's most basic sonar operations. The in- structions presented in Sec. 3 follow a chronological order. Sec. 4, Sonar Options & Other Features , will discuss the more advanced functions and utilities.
38 1. PWR/LIGHT (Power & Light) – The PWR key turns the unit on and off and controls the backlight level. 2. PAGES – Pressing this and the ↑ and ↓ arrow keys switches the unit between the three different page display options. (Full Sonar Chart, Split Zoom Sonar Chart and Digital Data.
39 Turn off the unit by pressing and holding the PWR key for 3 seconds. Main Menu The unit has a Main Menu which contains both function and setup op- tion commands. The instructions in this section will deal with sonar functions, the basic commands that make the unit show sonar signals on the screen.
40 The Main Menu commands and their functions: Screen command changes the contrast, brightness or display mode. Sounds command enables or disables the sound, set the volume or set the alarm style. Transparency command adjusts the level of transparency for dialogs.
41 Pages Menu showing Sonar display options. All of the display options show the sonar chart in some format. This is a "cross-section" view of the water column beneath the boat. The chart moves across the screen, displaying sonar signal echoes that represent fish, structure and the bottom.
42 Sonar page in Split Zoom Sonar Chart display mode. Sonar page in Digital Data display mode..
43 Sonar Page Menu. Most of these functions are discussed in Sec. 4. The Sonar Page has its own menu which is used for some advanced func- tions and for setting various options. Sonar Options and other features are discussed in Sec. 4. To access the Sonar Page menu press MENU once.
44 Sonar Page showing full sonar chart mode. Surface clutter Bottom signal Fish arches In FasTrack, fish arches show as horizontal bars. Depth scale Digital data overlay (depth & temperature) Surf.
45 Basic Sonar Quick Reference 1. Mount the transducer and unit. Connect the unit to electric power and the transducer. 2. Launch your boat. 3. To turn the unit on press and release the PWR key. 4. Head for your fishing spot. The unit should automatically display digital depth and surface water temperature in the corner of the screen.
46 depth appears in a box at the right end of the cursor line. To clear the cursor, press EXIT . 9. If you are drifting at a very low speed or anchored, you are not mov- ing fast enough for a fish to return the tell-tale fish arch signal.
47 These figures show results of different sensitivity levels on the same lo- cation. Fig. 1: Sensitivity at 88 percent, determined by Auto Sensitivity. Typical of full auto mode. Fig. 2: Sensitivity set at 75 percent. Fig. 3: Sen- sitivity set at 50 percent.
48 Adjusting sensitivity in Auto Sensitivity Mode is similar to manually adjusting a car's speed with the accelerator pedal while cruise control is on. You can tell the car to run faster, but when you let off the gas the cruise control automatically keeps you from running slower than the minimum speed setting.
49 Sonar Menu (left) with Sensitivity command selected. The Sensitivity Control Bar is shown at right. NOTE: If you want to change the sensitivity in Manual Mode, first turn off Auto Sensitivity. From the Sonar Page press MENU | ↓ to A UTO S ENSITIVITY | ENT | ↑ to S ENSITIVITY | ENT .
50 Fish Symbols vs. Full Sonar Chart You may have noticed in the quick reference we used fish arches in full sonar chart mode for our example instead of the popular Fish I.D. fish symbol feature. Here's why. Fish I.D. is an easier way for a sonar novice to recognize a fishy signal return when he sees it.
51 For the ultimate training aid download the free emulator software for your unit. Aside from being just plain fun, this program can help you learn both basic and advanced operations without burning boat fuel. Eagle is one of the first sonar manufacturers to provide this type of training tool for customers.
52 Notes.
53 Section 4: Sonar Options & Other Features Material in this section is arranged in alphabetical order. ASP (Advanced Signal Processing) The ASP feature is a noise rejection system built into the sonar unit that constantly evaluates the effects of boat speed, water conditions and interference.
54 Sonar Menu (left) with Sonar Features selected. In the Sonar Features menu (center) the SeaFinder's Noise Rejection feature is se- lected with ASP in the default low setting. The No ise R ej ec ti on fe at ure (far right) is set the same in the FishMark unit.
55 Depth Alarms The depth alarms sound a tone when the bottom signal goes shallower than the shallow alarm's setting or deeper than the deep alarm's set- ting. For example, if you set the shallow alarm to 10 feet, the alarm will sound a tone if the bottom signal is less than 10 feet.
56 3. Press ← to Shallow Alarm E NABLED | ENT | EXIT . 4. To turn the alarm off press ALARM | ENT | EXIT . To switch to a different depth setting, open the Sonar Alarms menu and repeat the instructions in step 3 above. To adjust and turn on the Deep Alarm: 1.
57 Sonar Alarms menu (left) with Adjust Zone command selected. Adjust Zone Alarm selection box (right) with Upper Limit selected. 4. Press EXIT | ← to Zone Alarm E NABLED | ENT | EXIT . Now, any echo — fish, bottom, structure — within the zone alarm's depth range will trig- ger the zone alarm.
58 Sonar Alarms menu with Fish Alarm selected. The check box to the left is blank, indicating the alarm is turned off. To turn the Fish Alarm on: 1. Press ALARM | ↓ to Fish Alarm| ENT | EXIT . 2. To turn off the alarm, press ALARM | ↓ to Fish Alarm| ENT | EXIT .
59 The unit's backlight level can be controlled from the Screen menu. Calibrate Speed The speed sensor can be calibrated to compensate for inaccuracies. Be- fore you change the setting, first calculate the percentage that the speed is off. You will enter this percentage in a moment.
60 Chart Speed The rate that echoes scroll across the screen is called the chart speed. The default is maximum. We recommend you leave the speed set at de- fault for virtually all fishing conditions. However, you might consider experimenting with chart speed when you are stationary or drifting very slowly.
61 1. From the Sonar Page, press MENU | ↓ to C HART S PEED | ENT . 2. The Chart Speed Control Bar appears. Press ↓ to decrease chart speed or press ↑ to increase chart speed. 3. When it's set at the desired level, press EXIT . ColorLine ColorLine lets you distinguish between strong and weak echoes.
62 Sonar Page menu (left) with ColorLine command selected. The ColorLine control bar is shown at right. Little ColorLine (left) indicates a soft bottom, probably sand or mud. The wider ColorLine (right) indicates a harder, rocky bottom. Depth Cursor The depth cursor consists of a horizo ntal line with a digital depth box on the right side.
63 Sonar Page menu (left) with Depth Cursor command selected. Sonar chart (right) with the depth cursor active. The school of fish is 31.91 feet deep. The cursor can be moved to any location on the screen, letting you pin- point the depth of a target.
64 Sonar Page menu (left) with Depth Range command selected. The Depth Range control scale is shown at right. 2. The Depth Range control scale appears. Press ↑ or ↓ to select a dif- ferent depth range. A blue bar highlights the selected range. The lighter numbers cannot be selected.
65 NOTE: The sonar's depth capability depends on the transducer installa- tion, water and bottom conditions and other factors. FasTrack This feature automatically converts all echoes to short horizontal lines on the display's far right side.
66 There are several fish symbol sizes. These are used to designate the relative size between targets. In other words, Fish I.D. displays a small fish symbol when it thinks a target is a small fish, a medium fish sym- bol on a larger target and so on.
67 To turn the Fish I.D. feature on: 1. From the Sonar Page, press MENU | ↓ to S ONAR F EATURES | ENT . 2. Press → to F ISH S YMBOLS | ENT | EXIT | EXIT . To turn off Fish I.D., repeat the instructions in step 2. FishTrack The FishTrack feature shows the depth of a fish symbol when it ap- pears on the display.
68 Frequency (Change Transducer Frequency) (SeaFinder unit only) The SeaFinder transducer operates with both 200 kHz and 50 kHz. The 200 kHz frequency has a 12 ° cone angle and the 50 kHz frequency has a 35 ° cone angle. The default frequency is 200 kHz which is best for shallow water (about 300 feet or less) conditions.
69 To change the frequency setting to 50 kHz: 1. From the Sonar Page, press MENU | ↓ to S ONAR F EATURES | ENT . 2. Press ↓ then → to Transducer Freq.| 50 K H Z | ENT . 3. Press EXIT | EXIT to clear the menu. To change the frequency setting to 200 kHz: 1.
70 Overlay Data command (left) on the Sonar Menu. Overlay Data Shown selection menu at right. In this example, Depth will be displayed in a large font. When selected, the data type shifts to the top of the data list and a check mark appears beside the data type.
71 3. To return to the previous page, press EXIT . To turn off displayed data: 1. Press MENU | ↓ to O VERLAY D ATA | ENT . 2. Press ↓ or ↑ to select Data Type | ENT . The selected data type disap- pears from the top of the list and reverts to its previous, unchecked po- sition.
72 Sonar Page with Overlay Data turned on. This example shows Depth, Water Temperature and Water Speed. NOTE: Some data types can be displayed in only one font size.
73 When using HyperScroll, you may al so need to manually decrease the sensitivity for optimum performanc e. Depending on water depth and other conditions, HyperScroll may caus e a second bottom echo to return to the transducer during the next ping cycle or sounding.
74 2. The Sensitivity Control Bar appears. Press ↓ to decrease sensitivity; press ↑ to increase sensitivity. When it's set at the desired level, press EXIT . When you reach the maximum or minimum limit a tone sounds. To turn off HyperScroll: 1.
75 Example showing the Pop-up Help message for the Sensitivity com- mand located on the Sonar Menu. Reset Options This command is used to reset all features, options and settings to their original factory defaults. This is useful when you have changed several settings and want to return the unit to basic automatic operation.
76 Main Menu (left) with Reset Options command selected. The Reset Op- tions dialog box (right) with "Yes" selected. Reset Water Distance The sonar chart's Digital Data display option includes a box that shows distance traveled, called Water Distance.
77 grounding or striking underwater structure. The Keel Offset feature eliminates the need for the navigator to mentally calculate how much water is under the keel. Keel Offset lets you calibrate the d igital depth, chart depth scale, chart cursor depth and fish symbol depth di splayed on the screen.
78 4. Press → to the second number, them press ↑ to change the num- ber to 5, then press EXIT . The depth indicators now accurately show the water depth from surface to bottom. Sensitivity & Auto Sensitivity The sensitivity controls the ability of the unit to pick up echoes.
79 level in manual mode the unit will continue to use that exact sensitivity setting until you change it or revert to auto mode. To adjust sensitivity in auto mode: 1. Press MENU | ENT . 2. The Sensitivity Control Bar appears. Press ↓ to decrease sensitivity.
80 NOTE: To return to the original factory setting for Auto Sensitivity, see the entry in this section on Reset Options. If sensitivity is in manual mode, the Reset Options command will switch back to Auto mode. Tip: For quicker sensitivity adjustments, try leaving the Sensitivity Control Bar on the screen as the chart scrolls.
81 To change the chart mode color scheme: 1. From the Sonar Page, press MENU | ↓ to S ONAR F EATURES | ENT . 2. Press → to S ONAR C HART M ODE | ENT . 3. Press ↓ or ↑ to Mode Name | ENT . 4. Press EXIT | EXIT to return to the Sonar Page. Sonar Page & Sonar Chart Display Options The Pages Menu offers three chart display options.
82 The FasTrack™ display shows just to the right of the scale. This changes all echoes into short horizontal bars, replicating a flasher so- nar. The zoom bar on the far right shows the area that's zoomed when the zoom is in use. (See the Zoom section for more information.
83 Split Zoom Sonar Chart. The left image shows the left split screen window zoomed to 2X. The right image shows the left split screen win- dow zoomed to 4X.
84 Digital Data/Chart Customizing the Digital Data/Chart Screen The Digital Data/Chart screen can be customized to show digital data different from the defaults first shown. To customize this screen: 1. From the Sonar Page (in Digital Data mode), press MENU | ↓ to C USTOMIZE | ENT .
85 2. The Water Speed box title bar flashes, indicating the box contents can be changed. Press ENT | ↑ or ↓ to select data type | ENT | EXIT . Water Speed has been selected to re place Water Depth in the top digital data box. Tip: You can customize other digital data boxes before returning to the Sonar Page.
86 Main Menu with Sonar Simulator command selected. The Simulator is turned off when the box is unchecked. NOTE: If you turn the unit on before atta ching a transducer, it may enter a demo mode. The words "demo mode" flash on the bottom of the screen and a sonar chart plays much like the simulator.
87 Sonar Menu with Stop Chart command selected. The box is unchecked, indicating that the chart is scrolling across the screen. Surface Clarity The markings extending downward from the zero line on the chart are called "surface clutter." These markings are caused by wave action, boat wakes, temperature inversion and more.
88 Sonar Features menu with Surface Clarity selected (at left, dual- frequency menu; at right, single-frequency menu). 2. Press ↓ to select Surface Clarity | ENT . In the illustration at left, Surface Clarity is turned off. The right view shows Surface Clarity set at High.
89 Experiment with this feature until you find the right level of transpar- ency for your eyes. Main Menu with Transparency command selected. To adjust Menu Transparency level: Press MENU | MENU | ↓ to T RANSPARENCY | ENT . The T RANSPARE NCY slider bar appears.
90 The Units of Measure Menu. To set Units of Measure: Press ↓ to the desired units, then press ENT . After all the options are set as desired, press EXIT | EXIT to return to the page display. Volume This command adjusts the speaker volume, which controls the sound levels for keystrokes and alarms.
91 Pressing ZIN once doubles the size (2X) of all echoes on the screen. Pressing it again quadruples the size of the echoes (4X). Pr ess th e Zo om Out key, ZOUT , to return the display to the normal mode. Sonar Page (left) in normal view. Same view (center) zoomed to 2X.
92 Notes.
93 Section 5: Troubleshooting If your unit is not working, or if you need technical help, please use the following troubleshooting section before contacting the factory customer service department. It may save you the trouble of returning your unit for repair.
94 Weak bottom echo, digital readings erratic, or no fish signals: 1. Make sure the transducer is po inting straight down. Clean the face of the transducer.
95 2. Electrical noise from the boat's motor can interfere with the sonar. This causes the sonar to automati cally increase its Discrimination or noise rejection feature. This can caus e the unit to eliminate weaker sig- nals such as fish or even structur e from the display.
96 signal on the display. Now turn on each piece of electrical equipment on the boat and view the effect on the sonar's display. For example, turn on the bilge pump and view the sonar display for noise. If no noise is present, turn the pump off, then turn on the VHF radio and transmit.
97 Section 6: Supplemental Material FCC Compliance This device complies with Part 15 of the U.S. Federal Communi- cations Commission (FCC) Rules. Operation is subject to the fol- lowing two conditions.
98 Notes.
99 EAGLE ELECTRONICS FULL ONE-YEAR WARRANTY "We," "our," or "us" refers to EAGLE ELECTRONICS, a division of LEI, the manufacturer of this product. "You" or "your" refers to the first person who purchases this product as a consumer item for personal, family, or household use.
100 How to Obtain Service… …in the USA: We back your investment in quality products with quick, expert service and genuine Eagle replacement parts. If you're in the United States and you have technical, return or repair questions, please contact the Factory Customer Service Department.
Accessory Ordering Information for all countries To order Eagle accessories such as power cables or transducers, please contact: 1) Your local marine dealer or consum er electronics store. Most quality dealers that handle marine electronic equipment or other consumer electronics should be able to assist you with these items.
Visit our web site: www.eaglesonar.com Eagle Pub. 988-0143-861 Copyright © 2005 All Rights Reserved Printed in USA 121205 LEI-Eagle .
Ein wichtiger Punkt beim Kauf des Geräts Eagle FISHMARK 640C (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Eagle FISHMARK 640C noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Eagle FISHMARK 640C - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Eagle FISHMARK 640C reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Eagle FISHMARK 640C erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Eagle FISHMARK 640C besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Eagle FISHMARK 640C verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Eagle FISHMARK 640C. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Eagle FISHMARK 640C gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
