Benutzeranleitung / Produktwartung ALE800 des Produzenten Dynalink
Zur Seite of 30
User Manual ALE800 Home DSL Modem.
able of Contents I. About This Manual 2 II. Preface 3 III. Overview 4 About ADSL 4 Protocol and Device Driver Selection 4 Features 8 Description of the Front Panel LEDs 9 Description of the Rear Panel Connectors 9 IV. USB ADSL Modem Hardware Installation 10 V.
2 This manual provides a comprehensive user’s guide and installation manual for USB ADSL modem. It has been organized in a way that should make it easy to follow by users worldwide. In order to ensure optimal comprehension, the following list provides brief descriptions of the formatting styles used in this manual.
3 This manual contains information regarding the installation, operation, and configuration of the USB ADSL Modem. Additionally, it outlines the use of the Control Panel Application.
4 About ADSL Asymmetric Digital Subscriber Line (ADSL) technology provides high-speed data access across regular phone lines (copper wires) by making use of previously unused frequency bandwidth above the voice band.
5 Several different protocols are used on top of ATM. The protocol required in your configuration depends on the equipment deployed by your DSL service provider.
6 1. WAN driver This driver causes the modem to resemble a dial-up modem. Call establishment is performed through Dial-Up Networking. This driver supports RFC 2364 and 2516 with PVC connections. It can be used with Windows 98, Windows 98 SE, Windows 2000, Windows Me, and Windows XP.
7 The device driver choices are summarized in the table below: Driver Type Protocol Operating System WAN RFC 2364 RFC 2516 (not with MAC OS 9.x, nor with MAC OS X) Windows 2000 Windows XP Windows Me Windows 98 SE Windows 98 LAN RFC 1483 RFC 2516 (MAC OS X 10.
8 Features The USB ADSL Modem provides the following features: Compliant with Universal Serial Bus Specification Revision 1.1 USB bus-powered; an external power supply is not required Supports three device drivers: Microsoft NDIS 4.0 WAN Miniport, NDIS 4.
9 Description of the front Panel LEDs LED LABEL Power (PW) LINK (LK) Color Status Green Green Green steady Power On Link Green blink N/A No Connection OFF Power Off N/A Table 1-1 Front Panel LEDs Desc.
10 Hardware Installation Install the USB ADSL Modem by following these steps with the PC running: 1. Insert the rectangular end of a USB cable into the USB port of your PC. 2. Insert the square end of the USB cable into the USB port of the USB ADSL Modem.
11 The software installation procedures vary depending upon the operating system of your PC. Be sure to follow the instructions provided for the operating system appropriate for you. Before you start… The following information may be required for software installation.
12 ATM Virtual Path ID (VPI) Note: Required if not using default value ATM Virtual Circuit ID (VCI) Note: Required if not using default value Encapsulation type Note: Required if not using.
Windows Installation The software setup process for Microsoft Windows applications (XP, 2000, Me, 98 SE, and 98) is described below with operating system specific differences noted. The USB ADSL Modem should be connected to your PC prior to installing the driver software.
14 3. A Licensing Agreement message will be displayed; click Accept. 4. The Select Service Provider window allows you to specify your DSL service provider.
15 a) Select the type of driver to be installed from the Select Driver Type window and click Next. b) Enter/Select the VPI, VCI, Encapsulation type and Modulation type from the Communication Settings window and click Next.
16 5. The Ready to Install window will be displayed. You may review the current settings and click Back to change the settings, or click Next to accept the current settings. 6. A message will be displayed indicating that the drivers are being installed.
17 7. The Installing window will be displayed. You may insert USB cable now. 8. The system must be rebooted to have the new settings take effect, therefore the Reboot window will appear. Remove all disks from their drives, select Yes, reboot the computer now; and click Close to reboot.
18 9. Once the PC has rebooted, installation of the USB Modem is complete. The Finished window will be displayed indicating the installation has been completed.
19 Accessing Communication Settings on Windows Once the USB ADSL Modem and software have been installed, the communication settings may be easily updated by performing the following steps: 1. From your PC desktop click Start Programs DSL Modem Configure.
20 Windows Drivers Update Once the USB ADSL Modem has been installed, updating to a new version of the software is an easy process. Simply uninstall the existing drivers, and then install the new drivers. Note: Be sure to follow the instructions provided for the appropriate operating system for your application.
21 The DSL Modem Status provides a quick and easy way to configure and check the performance of the modem and the ADSL connection. When open, the monitor window updates every 2 seconds.
22 3. Driver Version and Control Panel Version would be listed after clicking button..
23 Windows Uninstall Remove the USB ADSL Modem software drivers by performing the following steps. 1. From your PC desktop click Start Programs DSL Modem Uninstall. 2. A message will be displayed asking you to confirm the removal of the USB ADSL modem software, click Yes.
24 5. A message will be displayed to remind you to unplug your modem. You may unplug the USB cable now. 6. The Reboot window will appear. Remove all disks from their drives, select Yes, reboot the computer now; and click Close to reboot. Note: The USB cable must be unplugged before the system is rebooted.
25 Point-to-Point Protocol over Ethernet PPPoE (Point-to-Point Protocol over Ethernet) is a specification for connecting multiple computer users on an Ethernet to a remote site through common customer premises equipment.
26 PPPoE for LAN Applications PPPoE is supported via third party software when implemented with a LAN driver, making the modem appear as a local area network (LAN) device to the operating system. It allows multiple computer users on an Ethernet to share a common DSL connection to the Internet.
27 USB ADSL Modem Connector The USB ADSL Modem is connected to your PC via a USB cable. The rectangular end of the USB cable inserts into the USB port of your PC while the square end of the cable inserts into the USB port of the USB ADSL Modem. An RJ-11 connector is provided for connection to the telephone line.
28 ITU G.992.2 Data Rates Data rates for G.992.2 (G.lite) mode are likewise partitioned at 32kb/s increments. The downstream data rates extend from 64 kb/s to 4 Mb/s. The upstream data rates extend from 32 kb/s to 1024 kb/s. Bit Rate (kb/s) Min Max Downstream 64 4000 Upstream 32 1024 Table 2: G.
29 System Requirements Windows Operating Systems Windows 98, Windows 98SE, Windows ME, Windows 2000, or Windows XP 32 MB RAM Pentium-class processor (200MHz or better) 1 Universal Serial Bus (USB) port 10 MB free HD space Hardware Requirements Processor Intel-compatible 80486 or higher, including Pentium and Pentium Pro.
Ein wichtiger Punkt beim Kauf des Geräts Dynalink ALE800 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Dynalink ALE800 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Dynalink ALE800 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Dynalink ALE800 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Dynalink ALE800 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Dynalink ALE800 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Dynalink ALE800 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Dynalink ALE800. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Dynalink ALE800 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
