Benutzeranleitung / Produktwartung Vigor2130n des Produzenten Draytek
Zur Seite of 296
.
Vigor2130 Series User’s Guide ii Vigor2130 Series High Speed Gigabit Router User’s Guide Version: 2. 1 Firmware Version: V1.5.2 Date: 21/05/2012.
Vigor2130 Series User’s Guide iii Copyright Information Copyright Declarations Copyright 2012 All rights reserved. This pub lication contains information that is protected by copyright.
Vigor2130 Series User’s Guide iv European Community Declarations Manufacturer: DrayTek Corp. Address: No. 26, Fu Shing Road, HuKou County, H sinChu Industrial Park, Hsin-Chu, Taiwan 303 Product: Vigor2130 Ser ies Router DrayTek Corp.
Vigor2130 Series User’s Guide v T T a a b b l l e e o o f f C C o o n n t t e e n n t t s s Pref ace ......................................................................................................... 1 1.1 Feat ures ..........................
Vigor2130 Series User’s Guide vi 3.6 How to configur e Dynamic DNS Serv ice on Vigo r2130 ........................................................ 64 Web Confi guration ................................................................................
Vigor2130 Series User’s Guide vii 4.8.1 Remote Acce ss Cont rol ................................................................................................ 169 4.8.2 PPTP Remote Dial-in...........................................................
Vigor2130 Series User’s Guide viii 4.16 Diagno stics ............................................................................................................... ......... 265 4.16.1 Ping ..........................................................
Vigor2130 Series User’s Guide 1 P P r r e e f f a a c c e e The Vigor2130 series are the routers with high speed in data transmission through WAN port and LAN ports. With hardware NAT acceleration, the rate of Vigor2130 series can be ideal for multi-media application.
Vigor2130 Series User’s Guide 2 Note: For the other buttons shown on the web pages, please refer to Chapter 4 for detailed explanation. 1 1 . . 3 3 L L E E D D I I n n d d i i c c a a t t o o r r s .
Vigor2130 Series User’s Guide 3 Interface Description Factory Reset Restore the default settings. Usage: Tu rn on t he router (ACT LED is blin king). Press the hole and keep for m ore than 5 sec onds. When y ou see the AC T LED begins to blink rapidly than usual, release th e butto n.
Vigor2130 Series User’s Guide 4 1 1 . . 3 3 . . 2 2 F F o o r r V V i i g g o o r r 2 2 1 1 3 3 0 0 n n LED Status Explanation Blinking The router i s powered on and run ning normally . ACT (Activity) Off The router is powe red off. On Hardware NAT is enab led.
Vigor2130 Series User’s Guide 5 Interface Description Factory Reset Restore the default settings. Usage: Tu rn on t he router (ACT LED is blin king). Press the hole and keep for m ore than 5 sec onds. When y ou see the AC T LED begins to blink rapidly than usual, release th e button.
Vigor2130 Series User’s Guide 6 1 1 . . 3 3 . . 3 3 F F o o r r V V i i g g o o r r 2 2 1 1 3 3 0 0 V V n n LED Status Explanation Blinking The router i s powered on and run ning normally . ACT (Activity) Off The router is powe red off. On Hardware NAT is enab led.
Vigor2130 Series User’s Guide 7 Interface Description Phone2/P hone1 Connector of analog phon e for VoIP communicatio n . Factory Reset Restore the default settings. Usage: Tu rn on t he router (ACT LED is blin king). Press the hole and keep for m ore than 5 sec onds.
Vigor2130 Series User’s Guide 8 1 1 . . 4 4 H H a a r r d d w w a a r r e e I I n n s s t t a a l l l l a a t t i i o o n n Before starting to configure the router, you have to connect your devices correctly. 1. Connect this device to a modem with a RJ-45 cable.
Vigor2130 Series User’s Guide 9 S S t t a a n n d d I I n n s s t t a a l l l l a a t t i i o o n n The Vigor2130 must be placed erectly. Therefore you have to install a stand onto the router to make it standing firmly. Please follow the figures listed below to finish the installation.
Vigor2130 Series User’s Guide 10 1 1 . . 5 5 P P r r i i n n t t e e r r I I n n s s t t a a l l l l a a t t i i o o n n You can install a printer onto the router for shar ing printing. All the PCs connected this router can print documents via the router.
Vigor2130 Series User’s Guide 11 4. Click Local printer attached to this computer and click Next. 5. In this dialog, choose Create a new port Type of port and use the drop down list to select Standard TCP/IP Port .
Vigor2130 Series User’s Guide 12 6. In the following dialog, type 192.168.1.1 (router’s LAN IP) in the field of Printer Name or IP Address and type IP_192.168.1.1 as the port name. Then, click Next . 7. Click Standard and choose Generic Network Card.
Vigor2130 Series User’s Guide 13 9. Now, your system will ask you t o choose right na m e of the printer that you installed onto the router. Such step can make correct driver loaded onto your PC.
Vigor2130 Series User’s Guide 14 The printer can be used for printing now. Most of the printers with different manufacturers are compatible with vigor router. Note 1: Some printers with the fax/scanning or other additional fun ctions are not supported.
Vigor2130 Series User’s Guide 15 B B a a s s i i c c S S e e t t t t i i n n g g s s For using the router properly, it is necessar y for you to change the password of web configuration for security and adjust primary basic settings.
Vigor2130 Series User’s Guide 16 2 2 . . 2 2 C C h h a a n n g g i i n n g g P P a a s s s s w w o o r r d d Please change the password for the or iginal security of the router. 1. Open a web browser on your PC and type http://192. 168.1.1. A pop-up window will open to ask for username and password.
Vigor2130 Series User’s Guide 17 6. Now, the password has been changed. Next time, use the new password to access the Web Configurator for this router. 2 2 . . 3 3 Q Q u u i i c c k k S S t t a a r r t t W W i i z z a a r r d d Notice: Quick Start Wizard for user mode operation is the same as for admin mode operation.
Vigor2130 Series User’s Guide 18 2 2 . . 3 3 . . 1 1 S S e e t t t t i i n n g g u u p p t t h h e e P P a a s s s s w w o o r r d d The first screen of Quick Start Wizard is entering login password. After typing the password, please click Next . 2 2 .
Vigor2130 Series User’s Guide 19 2 2 . . 3 3 . . 3 3 S S e e t t t t i i n n g g u u p p t t h h e e I I n n t t e e r r n n e e t t C C o o n n n n e e c c t t i i o o n n On the next page as shown below, please select the appropriate connection type according to the information from your ISP.
Vigor2130 Series User’s Guide 20 Item Description IP Address Type the IP address. Subnet Mask Type the subnet mask. Gateway Type the gateway IP address. Primary DNS Server Type in the primary IP address for the router. Secondary DNS Server Type in secondary IP address for necessity in the future.
Vigor2130 Series User’s Guide 21 Item Description After finishing the settings here, please click Next. P P P P P P o o E E PPPoE stands for Point-to-Point Protocol over Ethernet .
Vigor2130 Series User’s Guide 22 Item Description MTU Size It means Max Transmit Unit for packet. The default setting will be specified by the system automatically. Therefore, keep this field in blank. Enable The router will detect the MAC address automatically.
Vigor2130 Series User’s Guide 23 Item Description Subnet Mask Type the subnet mask if you chose Static IP as the WAN IP. Redial Policy If you want to connect to Internet all the time, you can choose Always On .
Vigor2130 Series User’s Guide 24 Item Description SSID It means the identification of the wireless LAN. SSID can be any text numbers or various special characters.
Vigor2130 Series User’s Guide 25 W W P P A A - - P P S S K K If you choose WPA-PSK as the security configuration, you have to specify WPA mode, algorithm and pre-shared key.
Vigor2130 Series User’s Guide 26 If you choose WPA-Radius as the security configuration, you have to specify WPA mode, algorithm, Radius server, Radius server port and Radius server secret respectively.
Vigor2130 Series User’s Guide 27 W W P P S S WPS (Wi-Fi Protected Setup) provides easy procedure to m ake network connection between wireless station and wireless access point (vigor router) with the encryption of WPA and WPA2.
Vigor2130 Series User’s Guide 28 2 2 . . 3 3 . . 5 5 S S a a v v i i n n g g t t h h e e W W i i z z a a r r d d C C o o n n f f i i g g u u r r a a t t i i o o n n Now you can see the following screen. It indicates that the setup is complete. Different types of connection modes will have different summary.
Vigor2130 Series User’s Guide 29 Item Description LAN interface. RX Packets -Displays the total received packets at the LAN interface. TX Bytes -Displays the total transmitted bytes at the LAN interface. RX Bytes -Displays the total received packets at the LAN interface.
Vigor2130 Series User’s Guide 30 2 2 . . 6 6 R R e e g g i i s s t t e e r r i i n n g g V V i i g g o o r r R R o o u u t t e e r r You have finished the configuration of Quick Start Wizard and you can surf the Internet at any time. Now it is the time to register your Vigor router to MyVigor website for getting more service.
Vigor2130 Series User’s Guide 31 4 The following page will be displayed after you logging in MyVigor. From this page, please click Add or Product Registration .
Vigor2130 Series User’s Guide 32 7 Now, you have finished the product registration. 8 After clicking OK , you will see the following page. Your router has been registered to myvigor website successfully. If you have not activated web content filter service by using Service Activation Wizard , you can activate the service from this step.
Vigor2130 Series User’s Guide 33 10 In the following page, check the b ox of “ I have read and accept the above Agreement ”. The system will find out the date for you to activate this version of service. Then, click Next . 11 When this page appears, click Register .
Vigor2130 Series User’s Guide 34 This page is left blank..
Vigor2130 Series User’s Guide 35 T T u u t t o o r r i i a a l l s s a a n n d d A A p p p p l l i i c c a a t t i i o o n n s s 3 3 . . 1 1 H H o o w w t t o o C C o o n n f f i i g g u u r r e e M.
Vigor2130 Series User’s Guide 36 I I I I . . E E x x a a m m p p l l e e Chart of Structure z PC 1 connects to the first LAN port of Vigor2130 and accesses Internet with WAN VLAN. z PC 2 connects to the forth LAN port of Vigor2130 and accesses Internet with LAN VLAN.
Vigor2130 Series User’s Guide 37 2. Open WAN>>802.1Q VLAN Tag Configuration to configure Multi-VLAN. Refer to the following graphic. 3. Open WAN>>VoIP WAN to configure VoIP WAN Setting. Note: At present, only DHCP, PPPoE and Static connection types are available.
Vigor2130 Series User’s Guide 38 4. Open VoIP >>SIP Accounts . Specify the connection interf ace for VoIP in the field of Register via . 5. Connect your PC or network device to the forth LAN port and t ype the username and password for PPPoE connection mode.
Vigor2130 Series User’s Guide 39 3 3 . . 2 2 L L A A N N t t o o L L A A N N I I P P S S e e c c V V P P N N b b e e t t w w e e e e n n V V i i g g o o r r 2 2 1 1 3 3 0 0 a a n n d d V V i i g g o.
Vigor2130 Series User’s Guide 40 6. Enter Vigor2130’s private network in the Local Network / Mask field. Enter Vigor2820’s private network in the Remote Network / Mask field. 7. Use default value “ Automatic ” for IKE phase 1 and phase 2 proposals .
Vigor2130 Series User’s Guide 41 V V P P N N c c o o n n f f i i g g u u r r a a t t i i o o n n o o n n V V i i g g o o r r 2 2 8 8 2 2 0 0 1. Create a LAN-to-LAN profile. 2. Enable it and give it a name. In this example the profile name is “test”.
Vigor2130 Series User’s Guide 42 6. Setup a pre-shared key , which must be the same as in Vigor2130. 7. Enter Vigor2130’s private network in the Remote Network IP / Mask field. 8. Click OK . Note: Vigor2130 supports the following proposals by default.
Vigor2130 Series User’s Guide 43 C C a a s s e e 2 2 : : V V P P N N d d i i r r e e c c t t i i o o n n f f r r o o m m V V i i g g o o r r 2 2 8 8 2 2 0 0 t t o o V V i i g g o o r r 2 2 1 1 3 3 0 0 V V P P N N c c o o n n f f i i g g u u r r a a t t i i o o n n o o n n V V i i g g o o r r 2 2 1 1 3 3 0 0 1.
Vigor2130 Series User’s Guide 44 V V P P N N c c o o n n f f i i g g u u r r a a t t i i o o n n o o n n V V i i g g o o r r 2 2 8 8 2 2 0 0 1. Create a LAN-to-LAN profile. 2. Enable it and give it a name. In this example the profile name is “test”.
Vigor2130 Series User’s Guide 45 3. Select Dial-Out as Call Direction and enable Always on . 4. Select IPSec Tunnel and enter Vigor2130’s WAN IP address in the Server IP/Host Name for VPN field. 5. Setup a pre-shared key , which must be the same as in Vigor2130.
Vigor2130 Series User’s Guide 46 3 3 . . 3 3 L L A A N N t t o o L L A A N N I I P P S S e e c c V V P P N N b b e e t t w w e e e e n n V V i i g g o o r r 2 2 1 1 3 3 0 0 a a n n d d V V i i g g o.
Vigor2130 Series User’s Guide 47 5. Setup a pre-shared key , which must be the same as in Vigor2820. 6. Setup the Local Identity and Remote Identity , which are for Vigor2130 and Vigor2820 respectively. During IPSec Aggressive mode negotiation, the VPN client must send its identity to the VPN server for verification.
Vigor2130 Series User’s Guide 48 V V P P N N c c o o n n f f i i g g u u r r a a t t i i o o n n o o n n V V i i g g o o r r 2 2 8 8 2 2 0 0 1. Create a LAN-to-LAN profile. 2. Enable it and give it a name. In this example the profile name is “test”.
Vigor2130 Series User’s Guide 49 3. Select Dial-in as Call Direction . 4. In Dial-Out Settings part, select IPSec Tunnel and press the Advanced button. 5. In the pop-up window please enter vigor2820 in the Local ID field. Click OK to return to the profile setting page.
Vigor2130 Series User’s Guide 50 C C a a s s e e 2 2 : : V V P P N N d d i i r r e e c c t t i i o o n n f f r r o o m m V V i i g g o o r r 2 2 8 8 2 2 0 0 t t o o V V i i g g o o r r 2 2 1 1 3 3 0 0 V V P P N N c c o o n n f f i i g g u u r r a a t t i i o o n n o o n n V V i i g g o o r r 2 2 1 1 3 3 0 0 1.
Vigor2130 Series User’s Guide 51 V V P P N N c c o o n n f f i i g g u u r r a a t t i i o o n n o o n n V V i i g g o o r r 2 2 8 8 2 2 0 0 1. Create a LAN-to-LAN profile.
Vigor2130 Series User’s Guide 52 2. Enable it and give it a name. In this example the profile name is “test”. 3. Select Dial-Out as Call Direction and enable Always on . 4. Select IPSec Tunnel and enter Vigor2130’s WAN IP address in the Server IP/Host Name for VPN field.
Vigor2130 Series User’s Guide 53 3 3 . . 4 4 H H o o w w t t o o c c o o n n f f i i g g u u r r e e s s e e t t t t i i n n g g s s f f o o r r D D L L N N A A S S e e r r v v i i c c e e i i n n V.
Vigor2130 Series User’s Guide 54 2. Make sure Internet connection is done. Open USB Application>>DLNA Server and click Install to install DLNA service into the USB storage device. 3. During the process of installation, you ca n click Show Detail to view the installation procedure.
Vigor2130 Series User’s Guide 55 5. After enabled successfully, new media device can be seen in My Network Places . The name of the media device is the Server Name configured in Step 4.
Vigor2130 Series User’s Guide 56 6. For the users of Windows7, please use Windows Media Player (WMP) to browse and play the files stored in the new service device. For other systems, please use VLC media play er (downloaded from Internet) to browse/locate and play the files.
Vigor2130 Series User’s Guide 57 3 3 . . 5 5 H H o o w w t t o o d d o o w w n n l l o o a a d d B B T T T T o o r r r r e e n n t t t t o o U U S S B B D D e e v v i i c c e e v v i i a a V V i i g g o o r r R R o o u u t t e e r r D D o o w w n n l l o o a a d d B B T T T T o o r r r r e e n n t t 1.
Vigor2130 Series User’s Guide 58 6. Simply wait for a few minutes to finish the installation. 7. When the installation is finished, the following page will be displayed.
Vigor2130 Series User’s Guide 59 9. Click Open . A pop up dialog will appear. 10. Click Select File to open the following dialog. Choos e the seed of BT torrent file and click Open . Note : Before uploading torrent files to the router, please search from Internet and store the seed of the BT torrent on our hard disk first.
Vigor2130 Series User’s Guide 60 11. Next, the router will start to download the file to the USB disk. You can add new seed of torrent file one by one by clicking Open to let the router download them at one time.
Vigor2130 Series User’s Guide 61 3. In the following screen, add a new entry for th e sharing folder/name. In this case, we give a name of bt_folder as Share Nam e for home folder (“/”) . Click OK . 4. Now, PCs in LAN connected to Vigor2130 can open a browser from his / her computer.
Vigor2130 Series User’s Guide 62 5. The sharing disk with the name of “ bt_folder” created above will be shown as the following figure. 6. Double click bt_folder to view the files in the disk.
Vigor2130 Series User’s Guide 63 7. If you want to check the BT Torrent files downloaded from Internet to USB disk, access into bt_folder>>downloads.
Vigor2130 Series User’s Guide 64 3 3 . . 6 6 H H o o w w t t o o c c o o n n f f i i g g u u r r e e D D y y n n a a m m i i c c D D N N S S S S e e r r v v i i c c e e o o n n V V i i g g o o r r 2 2 1 1 3 3 0 0 DDNS stands for Dynamic DNS. Simply put, using this service gives a nam e to your IP.
Vigor2130 Series User’s Guide 65 3. Copy the character strings from the right of the ? in the address bar. 4. Login to Vigor2130 by W UI, and go to Application >>Dynamic DNS page. Select freedns.afraid.org , and fill in the username as you applied for the service.
Vigor2130 Series User’s Guide 66 This page is left blank..
Vigor2130 Series User’s Guide 67 W W e e b b C C o o n n f f i i g g u u r r a a t t i i o o n n This chapter will guide users to execute adva nced (full) configuration thr ough admin mode operation. 1. Open a web browser on your PC and type http://192.
Vigor2130 Series User’s Guide 68 From 10.0.0.0 to 10.255.255.255 From 172.16.0.0 to 172.31.255.255 From 192.168.0.0 to 192.168.255.255 W W h h a a t t a a r r e e P P u u b b l l i i c c I I P P A A.
Vigor2130 Series User’s Guide 69 Below shows the menu items for WAN . 4 4 . . 1 1 . . 1 1 I I n n t t e e r r n n e e t t A A c c c c e e s s s s This page allows you to set WAN configura tion with different modes. Use the Connection Type drop down list to choose one of the WAN modes.
Vigor2130 Series User’s Guide 70 be applied to each connection type. Below shows the configuration page for each connection type: S S t t a a t t i i c c For static IP mode, you usually receive a fixe d public IP address or a public subnet, nam ely multiple public IP addresses from your DSL or Cable ISP service providers.
Vigor2130 Series User’s Guide 71 Available settings are explained as follows: Item Description Static IP Settings IP Address -Type the IP address. Subnet Mask - Type the subnet mask.
Vigor2130 Series User’s Guide 72 Clone MAC Address Enable – Enable the feature. It is available when the box of Enable is checked. Click Clone MAC Address .
Vigor2130 Series User’s Guide 73 Available settings are explained as follows: Item Description DHCP Settings Router Name - Type in a name for the router. It must be the same as the name used in Syslog. Domain Name - Type the domain name (e.g., draytek) to fit the request of some ISPs.
Vigor2130 Series User’s Guide 74 P P P P P P o o E E To choose PPPoE as the accessing protocol of the internet, please select PPPoE from the Internet Access menu. The following web page will be shown. Available settings are explained as follows: Item Description PPPoE Settings Username -Type in the username provided by ISP in this field.
Vigor2130 Series User’s Guide 75 Fixed IP (IPCP) - Usually ISP dynamically assigns IP address to you each time you connect to it and request. In some case, your ISP provides service to always assign you the same IP address whenever you request. In this case, you can fill in this IP address in the Fixed IP field.
Vigor2130 Series User’s Guide 76 P P P P T T P P / / L L 2 2 T T P P To use PPTP/L2TP as the accessing protocol of the internet, please choose PPTP/L2TP from Connection Type drop down menu.
Vigor2130 Series User’s Guide 77 address here because your ISP should provide you wit h usually more than one DNS Server . If your ISP does not provide it, the router will automatically apply default DNS Server IP address: 194.109.6.66 to this field.
Vigor2130 Series User’s Guide 78 Event types – Specify the event when the system must send a notification to the user by mail and/or SMS. After finishing all the settings here, please click OK to activate them.
Vigor2130 Series User’s Guide 79 3 3 G G U U S S B B M M o o d d e e m m If your router connects to a 3G modem and you wa nt t o access Internet via 3G modem, choose 3G as connection type and type the re quired inform ation in this web page.
Vigor2130 Series User’s Guide 80 WAN Connection Detection Mode - Such function allows you to verify whether network connection is alive or not through ARP De tect or Ping Detect. Choose ARP Detect or Ping Detect for the system to execute for WAN detection.
Vigor2130 Series User’s Guide 81 5 5 6 6 K K M M o o d d e e m m If your router connects to a 56K modem and you want to access Internet via 56K modem, choose 56K Modem as connection type and type the required inform ation in this web page.
Vigor2130 Series User’s Guide 82 Mail/SMS Alert Alert Types – Specify the type of the alert (mail, SMS, or Mail and SMS) that Vigor system will use to send a message to the user. Event types – Specify the event when the system must send a notification to the user by mail and/or SMS.
Vigor2130 Series User’s Guide 83 APN Name - APN means Access Point Name which is provided and required by some ISPs. WAN Connection Detection Mode - Such function allows you to verify whether network connection is alive or not through ARP De tect or Ping Detect.
Vigor2130 Series User’s Guide 84 4 4 . . 1 1 . . 2 2 M M u u l l t t i i - - V V L L A A N N Vigor2130 series offers multi-VLAN function to make the data transmission with security. Data transmitting through the Ethernet port for connecting to Internet can be tagged with an ID number specified here for ensuring the secur ity.
Vigor2130 Series User’s Guide 85 port will be tagged with VLAN ID number specified here. The range of ID number you can type is from 2 - 409 6. VoIP WAN Setting – Click this link to open VoIP WAN setting.
Vigor2130 Series User’s Guide 86 V V o o I I P P / / I I P P T T V V / / M M a a n n a a g g e e m m e e n n t t W W A A N N S S e e t t t t i i n n g g VoIP/ IPTV / Management WAN is the interface specified for the usage of VoIP/ IPTV / Management.
Vigor2130 Series User’s Guide 87 Available settings are explained as follows: Item Description DHCP Setting Router Name- Type the nam e of the router.
Vigor2130 Series User’s Guide 88 Available settings are explained as follows: Item Description PPPoE Setting Username - Type the name obtained from the ISP. Password - Type the password obtained from the ISP. Confirm Password -Type the password again for confirmation.
Vigor2130 Series User’s Guide 89 Flow Control If flow control is enabled by checking Configured box, both parties can send PAUSE frame to the transm itting device(s) if the receiving port is too busy to handle. If not, there will be no flow control in the port.
Vigor2130 Series User’s Guide 90 After finishing all the settings here, please click OK to activate them. 4 4 . . 1 1 . . 4 4 B B a a c c k k u u p p This page is used to setup 3G/56K backup func tio n. If you enable 3G/56K backup, make sure your WAN connection type is not in 3G/56K m ode.
Vigor2130 Series User’s Guide 91 question, please contact to your ISP. PPP Username - Type the PPP username (optional). PPP Password - Type the PPP password (optional). WAN Connection Detection Mode - Such function allows you to verify whether network connection is alive or not through ARP De tect or Ping Detect.
Vigor2130 Series User’s Guide 92 Item Description 56K Backup Enable 56K Backup - Check this box to enable such function. Phone Number - Type the phone number offered by the ISP for dial-out connection. PPP Username - Type the PPP username (optional).
Vigor2130 Series User’s Guide 93 4 4 . . 2 2 L L A A N N Local Area Network (LAN) is a group of subnets regulated and ruled by router . The design of network structure is related to what type of public IP addresses coming from your ISP . B B a a s s i i c c s s o o f f L L A A N N The most generic function of V igor router is NA T .
Vigor2130 Series User’s Guide 94 W W h h a a t t i i s s R R o o u u t t i i n n g g I I n n f f o o r r m m a a t t i i o o n n P P r r o o t t o o c c o o l l ( ( R R I I P P ) ) V igor router will exchange routing informati on with neighboring routers using the RIP to accomplish IP routing.
Vigor2130 Series User’s Guide 95 4 4 . . 2 2 . . 1 1 G G e e n n e e r r a a l l S S e e t t u u p p This page provides you the general settings for LAN.
Vigor2130 Series User’s Guide 96 related IP settings to any local user configured as a DHCP client. It is highly recommended that you leave the router enabled as a DHCP server if you do not have a DHCP server for your network. Y ou can configure the router to serve as a DHCP server for the 2nd subnet.
Vigor2130 Series User’s Guide 97 4 4 . . 2 2 . . 2 2 P P o o r r t t s s Ports page is used to change the setting fo r LAN ports. You can set or reset the following items. All of them are described in detail below. Available settings are explained as follows: Item Description Port It displays current network interface.
Vigor2130 Series User’s Guide 98 Discard - It determines whether the MAC drops frames after an excessive collision has occurred. If yes, a frame is dropped after excessive collision.
Vigor2130 Series User’s Guide 99 4 4 . . 2 2 . . 3 3 M M A A C C A A d d d d r r e e s s s s T T a a b b l l e e This page allows you to set timeouts for en tries in dynamic MAC Table and configure the static MAC table here.
Vigor2130 Series User’s Guide 100 setting. To add a new static MAC entry, click Add new static entry . A new entry will be shown as follows. Choose a VLAN ID and type a new MAC address. Next, specify port member for this table. Finally, click OK to save the changes.
Vigor2130 Series User’s Guide 101 3. T o remove VLAN, click the Delete button fo r the one you want to r emove and click OK to save the results. 4 4 . . 2 2 . . 5 5 M M o o n n i i t t o o r r P P o o r r t t It is used to monitor the traffic of the networ k.
Vigor2130 Series User’s Guide 102 4 4 . . 2 2 . . 6 6 S S t t a a t t i i c c R R o o u u t t e e Go to LAN to open setting page and choose Static Route . Available settings are explained as follows: Item Description Set to Factory Default Click this link to return to the factory default settings.
Vigor2130 Series User’s Guide 103 1. Click the LAN - S tatic Route and click Add. Check the Enable box. Please add a static route as shown below , which regulates all p ackets destined to 192.168.10.0 will be forwarded to 192.168.1.2. Click OK . 2. Return to St a t i c R o u t e page.
Vigor2130 Series User’s Guide 104 3. V erify current routing table. 4 4 . . 2 2 . . 7 7 P P o o l l i i c c e e R R o o u u t t e e Go to LAN to open setting page and choose Police Route . Available settings are explained as follows: Item Description Set to Factory Default Click this link to return to the factory default settings.
Vigor2130 Series User’s Guide 105 To add a new police route, please click Add to open the following page. Available settings are explained as follows: Item Description Enable Check it to enable such route. Source IP Address Type the source address for such policy route.
Vigor2130 Series User’s Guide 106 Available settings are explained as follows: Item Description Enable Click this radio button to invoke this fu nction. However, IP/MAC which is not listed in IP Bind List also can connect to Internet. Disable Click this radio button to disable this function.
Vigor2130 Series User’s Guide 107 Bypass Login means no need to type username and password for accessing into Inte rnet. The user still can see the bulletin and the web page redirected. Disable (Bypass) All means no need to type username and password.
Vigor2130 Series User’s Guide 108 4 4 . . 2 2 . . 9 9 W W e e b b P P o o r r t t a a l l Web portal, a management program used for clients, allows you to set login account, e-bulletin and URL redirection. Available settings are explained as follows: Item Description Login Different login method specified here will lead to different login page.
Vigor2130 Series User’s Guide 109 format. HTTPS is safer than HTTP. Disable – Click it to skip the login proc edure. Account Setting Common account – Any user who wants to surf Internet must type account and password first. When the username and password authenticated by the system are correct, the user can be allowed to access into Internet.
Vigor2130 Series User’s Guide 110 the web portal page. Login – A window will be opened and ask you t o type username (ID) and password (P/W) for accessing into the web page. Bypass/disable login – A window will be opened for you to accessing into the web page.
Vigor2130 Series User’s Guide 111 4 4 . . 3 3 N N A A T T Usually, the router serves as an NAT (Network Address Translation) router. NAT is a mechanism that one or more private IP a ddresses can be mapped into a single public one. Public IP address is usually assigned by your ISP, for which you may get charged.
Vigor2130 Series User’s Guide 112 4 4 . . 3 3 . . 1 1 H H a a r r d d w w a a r r e e N N A A T T Hardware-base Accelerati on Engine, also na med Protocol Processing Engine API is the function that DrayTek provides to ex tremely speed up the NAT performance.
Vigor2130 Series User’s Guide 113 Available settings are explained as follows: Item Description Enable Check this box to enable this function. Name Specify the name for the defined network service. Protocol Specify the transport layer protocol. It could be TCP , UDP and TCP+UDP .
Vigor2130 Series User’s Guide 114 4 4 . . 3 3 . . 3 3 D D M M Z Z H H o o s s t t As mentioned above, Port Redirection can redirect incoming TCP/UDP or othe r traffic on particular ports to the specific private IP address/port of host in the LAN.
Vigor2130 Series User’s Guide 115 Choose PC Bring a dialog for you to choose an IP address. Click OK to save the settings. 4 4 . . 4 4 F F i i r r e e w w a a l l l l B B a a s s i i c c s s f f o o.
Vigor2130 Series User’s Guide 116 Item Description Frame Type Set the Unicast storm rate control, multicast storm rate control, and a broadcast storm rate control for your router. Status Check this box to enable storm control status for the frame type.
Vigor2130 Series User’s Guide 117 Disabled . Counter Counts the number of frames that match this Access Control Entry (ACE). Refresh Click this button to refresh the number of the counter immediately. Clear Click this button to clear the number of the counter on this page.
Vigor2130 Series User’s Guide 118 list. Click OK to save the settings..
Vigor2130 Series User’s Guide 119 4 4 . . 4 4 . . 3 3 A A c c c c e e s s s s C C o o n n t t r r o o l l L L i i s s t t This page can define which kind of packet can access the router. The packet can be defined with input port, Frame type, Rate, MAC t ype, VLAN ID, tag and etc.
Vigor2130 Series User’s Guide 120 selection you choose, we will explain it in detailed later. Action – it means the session limitation for this access control list will be applied to if matching with the rule defined in this page. Rate Limiter - Select a rate limiter to apply to this port.
Vigor2130 Series User’s Guide 121 D D e e t t a a i i l l e e d d E E x x p p l l a a n n a a t t i i o o n n f f o o r r F F r r a a m m e e T T y y p p e e Frame Type selection will lead different options for configuration.
Vigor2130 Series User’s Guide 122 Request/Reply Choose the request or replay that you want to filter. Sender IP Filter Specify the sender IP filter for this ACE. Choose Any to filter all of the packets. Choose Host to filter the packets from the host with the address typed in Sender IP Address filed.
Vigor2130 Series User’s Guide 123 address. 1 : means sender hardware address is equal to the SMAC address. Any : means any value is allowed. RARP DMAC Match Specify whether frames can hit the action according to their target hardware address field (THA) settings.
Vigor2130 Series User’s Guide 124 0: ARP/RARP frames where the protocol address space is equal to IP (0x800) must not match this entry. 1: ARP/RARP frames where the protocol address space is equal to IP (0x800) must match this entry. Any: Any value is allowed.
Vigor2130 Series User’s Guide 125 Any: No destination IP filter is specified. Host: Destination IP filter is set to Host. Specify the destination IP address in the Dest IP Address field that appears. Network: Destination IP filter is set to Network.
Vigor2130 Series User’s Guide 126 Available settings are explained as follows: Item Description Source IP Specify the source IP filter for this ACE. Any: No source IP filter is specified. Host : Source IP filter is set to Host. Specify the source IP address in the Source IP Address field that appears.
Vigor2130 Series User’s Guide 127 Source Port Filter Specify the UDP port source filter for this ACE. Any: No UDP source filter is specified. Specific: If you want to filter a specific UDP source filter with this ACE, you can enter a specific UDP source value.
Vigor2130 Series User’s Guide 128 z Choose IPv4 as the Frame Type . You will see IP Parameters on the bottom of the page. If you choose TCP as IP Protocol Filter , you will get the page as the following: Available settings are explained as follows: Item Description Source IP Specify the source IP filter for this ACE.
Vigor2130 Series User’s Guide 129 Dest IP Address Type the destination IP Ad dress here. This option is available when you choose Host or Network as destination IP filter. Dest IP Mask Type the destination IP Mask here. This option is available only when you choose Network as destination IP filter.
Vigor2130 Series User’s Guide 130 0: TCP frames where the FIN field is set must not be able to match this entry. 1: TCP frames where the FIN field is set must be able to match this entry. Any: Any value is allowed. TCP SYN Specify the TCP "Synchronize sequence numbers" (SYN) value for this ACE.
Vigor2130 Series User’s Guide 131 0: TCP frames where the ACK field is set must not be able to match this entry. 1: TCP frames where the ACK field is set must be able to match this entry. Any: Any value is allowed. TCP URG Specify the TCP "Urgent Pointer field significant" (URG) value for this ACE.
Vigor2130 Series User’s Guide 132 address in the source IP Address field that appears. Network: Source IP filter is set to Network. Specify the source IP address and source IP mask in the source IP Address and source IP Mask fields that appear. Source IP Address Type the source IP Address here.
Vigor2130 Series User’s Guide 133 A A d d d d i i n n g g a a N N e e w w T T r r a a f f f f i i c c C C o o n n t t r r o o l l P P r r o o f f i i l l e e You are allowed to add many traffic control rules for your request. 1. Click Add Entry , the following screen will be shown.
Vigor2130 Series User’s Guide 134 Action Choose the action to perform for the filtered packet. Accept – Packets matching with such rule can pass through the router.
Vigor2130 Series User’s Guide 135 You can click to open the selected profile for an y modification; click to delete the selected profile. 4 4 . . 4 4 . . 5 5 T T i i m m e e O O b b j j e e c c t t The time object can be applied to firewall rules only.
Vigor2130 Series User’s Guide 136 2. After finishing the settings, click OK to save and exit the page. 4 4 . . 5 5 C C S S M M CSM is an abbreviation of Content Security Management which is used to control IM/P2P usage, filter the web content and URL conten t to reach a goal of security management.
Vigor2130 Series User’s Guide 137 Web Feature Filter If you do not check any box here, it means Vigor router will not prevent users from accidentally downloading m alicious codes conceal in the executa ble objects from web pages. Filters – Choose any one of the items to be filtered by such router.
Vigor2130 Series User’s Guide 138 4 4 . . 5 5 . . 2 2 W W e e b b C C o o n n t t e e n n t t F F i i l l t t e e r r We all know that the content on the Internet just like other types of media may be inappropriate sometimes. As a r esponsible parent or employer, you should protect those in your trust against the hazards.
Vigor2130 Series User’s Guide 139 Status Display if such profile is enabled or not. If yes, a green check mark will be shown here. Source Display the range for source IPs. Filter Https Display the HTTPS for filtering. Such i nformation is supported by Commtouch only.
Vigor2130 Series User’s Guide 140 OK Save the settings. Back Return to previous page. 5. After finished the configuration, click OK to save the settings. A new entry is added successfully on the web page. F F o o r r C C o o m m m m t t o o u u c c h h s s e e r r v v i i c c e e , , 1.
Vigor2130 Series User’s Guide 141 License Information Display the license infor m ation for current used. If the WCF mechanism has been activated successfully, a green light will be shown on the screen. Provider Display the service provider of WCF. Activate Click it to activate Commtouch WCF mechanism.
Vigor2130 Series User’s Guide 142 4. Click Add a New Entry to open the following page and t ype all the required information. Each item is explained as follows: Item Description Name Type a profile name for WCF service. Enable Click it to enable such profile.
Vigor2130 Series User’s Guide 143 Time Apply the time object to such profile. Choose any one of the time object profiles from the drop down list. You can create another one by clicking the link of New Time Object . Filter Https Check it to enable the HTTPS filtering of WCF.
Vigor2130 Series User’s Guide 144 1. Click Add Entry to open the following time object setting page. Available settings are explained as follows: Item Description Enable Check the box to enable such rule. Name Type a name of the rule for identification.
Vigor2130 Series User’s Guide 145 Time Profile Specify a period for filtering the packets with web feature filter. Use the drop down list to choose the time setting, or click New Time Object to define a time period for you necessity. New Time Object – Such link allows you to create new time object for using by web feature filter.
Vigor2130 Series User’s Guide 146 Available settings are explained as follows: Item Description Enable Click this button to activate the function of limit session. Disable Click this button to close the function of limit session. Default Sessions Limit Defines the default ses sion number used for each computer in LAN.
Vigor2130 Series User’s Guide 147 4 4 . . 6 6 . . 2 2 B B a a n n d d w w i i d d t t h h L L i i m m i i t t The downstream or upstream from FTP, HTTP or so me P2P applications will occupy large of bandwidth and affect the applications for othe r programs.
Vigor2130 Series User’s Guide 148 Specific Limitation This section is allowed to configure the user-defined limitation for bandwidth. Limitation List - Display a list of specific limitations that you set on this web page. Start IP - Bandwidth limit can be applied on certain IP range.
Vigor2130 Series User’s Guide 149 4 4 . . 6 6 . . 3 3 P P o o r r t t R R a a t t e e C C o o n n t t r r o o l l A policer can limit the bandwidth of received frames. It is located in front of the ingress queue. And a shaper can limit the bandwidth of tran smitted frames.
Vigor2130 Series User’s Guide 150 (or in another term “dropped”) from an overflow ing queue, packets of sensitive applications mentioned above might be the ones to drop off.
Vigor2130 Series User’s Guide 151 Available settings are explained as follows: Item Description QCL # QCL (QoS Control List) allows users to set up to five QCL groups. Each QCL group can contain 12 QCE (QoS Control Entry) settings. QCE Type Display the type of QCE (QoS Control Entries).
Vigor2130 Series User’s Guide 152 Available settings are explained as follows: Item Description Ethernet Type Value Either 8~63 ASCII characters, such as 012345678(or 64 Hexadecimal digits leading by 0x, such as "0x321253abcde..."). Traffic Class Specify traffic class fro m Low, Normal, Medium and High.
Vigor2130 Series User’s Guide 153 Available settings are explained as follows: Item Description TCP/UDP Port Click Single or Range . If you select Range, you have to type in the starting port number and the end porting num ber on the boxes below.
Vigor2130 Series User’s Guide 154 Available settings are explained as follows: Item Description ToS Priority 0 Class ~ ToS Priority 7 Class ToS means Type of Service. Use the precedence part of IPv4/IPv6 ToS (3 bits) as an index to the eight QoS Class values in QCE.
Vigor2130 Series User’s Guide 155 Click to modify the settings of an existing QCE on this page. M M o o v v i i n n g g U U p p / / D D o o w w n n a a Q Q C C E E Click and to move a QCE up and down. D D e e l l e e t t i i n n g g a a Q Q C C E E To delete a QCE in the list, simply click of that one.
Vigor2130 Series User’s Guide 156 Queuing Mode Use the drop down list to choose suitabl e mode. Queuing Weighted Use the drop down list to choose 1, 2, 4, or 8 as the queue weighted number. Click OK to save the settings. 4 4 . . 6 6 . . 6 6 Q Q o o S S S S t t a a t t i i s s t t i i c c s s This page displays statistics for QoS se tting.
Vigor2130 Series User’s Guide 157 Each item is explained as follows: Item Description Rx Packets Display the counting number of the packet received. Rx Octets Display the total received bytes. Rx Unicast Display the counting number of the received unicast packet.
Vigor2130 Series User’s Guide 158 bad packets received. RX 1024- 1526 Bytes Display the number of 1024-1522-byte frames in goo d and bad packets received. RX 1527 Bytes Display the number of 1527-byte frames in good and bad packets received. Rx Low Display the low queue counter of the packet received.
Vigor2130 Series User’s Guide 159 bad packets transmitted. Tx 1024- 1526 Bytes Display the number of 1024 ~ 1522-byt fram es in good and bad packets transmitted. Tx 1527 Bytes: Display the number of 1527-byte frames in good and bad packets transmitted.
Vigor2130 Series User’s Guide 160 Available settings are explained as follows: Item Description Index Display the number that you can click to edit the settings. Setting Display the domain name of the profile. If no domain is specified, it will display Host instead.
Vigor2130 Series User’s Guide 161 My WAN IP – Use IP configured for WAN interface for DDNS server. My Internet IP – Use true IP for DDNS server. Check IP change every Set the interval for checking the information. Force IP update every Force the router updates its information to DDNS server with the interval set here.
Vigor2130 Series User’s Guide 162 Available settings are explained as follows: Item Description Enable Check to enable the schedule. Start Date Specify the starting date of the schedule. Start Time Specify the starting time of the schedule. Action Specify which action should be applied during the period of the schedule.
Vigor2130 Series User’s Guide 163 Click OK button to activate the settings. You will see your setting has been saved. 4 4 . . 7 7 . . 3 3 I I G G M M P P IGMP snooping means multicast traffic will be forwarded to ports that have members of that group.
Vigor2130 Series User’s Guide 164 IGMP Snooping Configuration Snooping Enabled - Check the box to enable this function. Unregistered IPMC Flooding enabled - Check the box to enable unregistered IPMC traffic flooding. Port Related Configuration Fast Leave - Check the box to fast leave from the LAN port.
Vigor2130 Series User’s Guide 165 the firewall to automatically open the ports that th ey need to pass through a router. It is more reliable than requiring a router to work out by itself which ports need to be opened. Further, the user does not have to manually set up port mappings or a DMZ.
Vigor2130 Series User’s Guide 166 and configure port mappings on the rout er . Subse quently , such a facility forwards packets from the external ports of the router to the internal ports used by the application.
Vigor2130 Series User’s Guide 167 Available settings are explained as follows: Item Description Wake by Two types provide for you to wake up the bond IP. If you choose Wake by MAC Address, you have to type the correct MAC address of the host in MAC Address boxes.
Vigor2130 Series User’s Guide 168 Available settings are explained as follows: Item Description Enable Check the box of Enable to enable SMS function. Profile Name Type a name for such SMS profile. Service Use the drop down list to specify the service provider which offers SMS service.
Vigor2130 Series User’s Guide 169 2. When you finished the configuration, click OK to save and return to previous page. 4 4 . . 8 8 V V P P N N a a n n d d R R e e m m o o t t e e A A c c c c e e s .
Vigor2130 Series User’s Guide 170 Enable IPSec VPN Pass-through (Server inside your LAN) If this checkbox is checked, the system firewall will allow VPN (IPSec) remote access from WAN side to a VPN device on the LAN. Type the IP address of the VPN device in the field next to the checkbox.
Vigor2130 Series User’s Guide 171 A A d d d d i i n n g g a a N N e e w w U U s s e e r r 1. Click Add a New User to open the following page. Available settings are explained as follows: Item Description Enable Check this box to enable such user profile.
Vigor2130 Series User’s Guide 172 traffic destined to this Remote Network IP Address/Remote Network Mask through the VPN connection. Allow FTP Check this box to let the rem ote user connecting to FTP server via this router. Allow TELNET Check this box to let the remote user to adjust the settings of router by TELNET.
Vigor2130 Series User’s Guide 173 4 4 . . 8 8 . . 3 3 I I P P S S e e c c R R e e m m o o t t e e D D i i a a l l - - i i n n This page allows you to confi gure IPSec Site-to-Client settings.
Vigor2130 Series User’s Guide 174 Authentication Type - There are two ty pes for you to choose for authentication. If you choose Certificate as the Type , you have to specify one of the local certificates. If you choose Pre-Shared Secret as the Type , you have to type and confirm the shared secret.
Vigor2130 Series User’s Guide 175 4 4 . . 8 8 . . 4 4 R R e e m m o o t t e e D D i i a a l l - - i i n n S S t t a a t t u u s s You can find the summary table of all dial-in user status. Available settings are explained as follows: Item Description Auto - refresh Check this box to make the system refresh this page automatically.
Vigor2130 Series User’s Guide 176 Login Time Display the system time that the user logs in. Rx bytes Display the data total received for such client.
Vigor2130 Series User’s Guide 177 Up Time Display the duration time of the IPSec / PPTP connection. Add Tunnel Click it to add a new VPN tunnel via IPSec / PPTP protocol. A A d d d d i i n n g g a a V V P P N N T T u u n n n n e e l l f f o o r r I I P P S S e e c c Click Add Tunnel to open the following page.
Vigor2130 Series User’s Guide 178 Available settings are explained as follows: Item Description General Enabled - Check here to activate this tunnel. Always On - Check this box to make the WAN connection being activated always. Name - Specify a name for this tunnel.
Vigor2130 Series User’s Guide 179 Advanced Security Settings IKE Phase 1 proposal - Propose the local available authentication schemes and encryption algorithms to the VPN peers, and get its feedback to find a match. IKE Phase 2 proposal - Propose the local available algorithms to the VPN peers, and get its feedback to find a match.
Vigor2130 Series User’s Guide 180 A A d d d d i i n n g g a a V V P P N N T T u u n n n n e e l l f f o o r r P P P P T T P P Click Add Tunnel to open the following page. Available settings are explained as follows: Item Description Dial-Out General Setting Enabled - Check here to activate this tunnel.
Vigor2130 Series User’s Guide 181 Route/NAT Mode - If the remote network only allows you to dial in with single IP, please choose NAT Mode, otherwise please choose Route Mode. Change default route to this VPN tunnel - Check this box to change the default route into such VPN tunnel.
Vigor2130 Series User’s Guide 182 4 4 . . 9 9 . . 1 1 T T r r u u s s t t e e d d C C A A C C e e r r t t i i f f i i c c a a t t e e The CA (certification authority) certificate specified in this page is the issuer of the certificat es for both clients requesting for network connection.
Vigor2130 Series User’s Guide 183 You can import other Root CA certificates made by others and upload t o Vigor router as CA. Simply click IMPORT to access into the following page. Available settings are explained as follows: Item Description Name Type a new name for such certificate.
Vigor2130 Series User’s Guide 184 If you want to create your Root CA certificate for the router adopting for issuing local certificate and certificate request fro m the remote client, simply click Build RootCA to access into the following page.
Vigor2130 Series User’s Guide 185 4 4 . . 9 9 . . 2 2 L L o o c c a a l l C C e e r r t t i i f f i i c c a a t t e e This page displays the certificate which will be authenticated for network connection. Note that it must be issued by Trusted CA Certificate first.
Vigor2130 Series User’s Guide 186 Available settings are explained as follows: Item Description General Name - Type a new name for such certificate. Keylength - Specify the length of the certificate. Sign by My Root CA – If you have created a Root CA for yourself, the check box will be available for you to activate.
Vigor2130 Series User’s Guide 187 4 4 . . 9 9 . . 3 3 I I s s s s u u e e C C e e r r t t i i f f i i c c a a t t e e Vigor router can be used as a Root CA to authenticate and issue the certificates request coming from other clients. Available settings are explained as follows: Item Description Certificate file Use the Browse.
Vigor2130 Series User’s Guide 188 also loaded with advanced wireless technology to lift up data rate up to 300 Mbps*. Hence, you can finally smoothly enjoy stream music and video.
Vigor2130 Series User’s Guide 189 4 4 . . 1 1 0 0 . . 2 2 G G e e n n e e r r a a l l S S e e t t u u p p By clicking the General Setup , a new web page will appear so that you could configure the SSID and the wireless channel. Please refer to the following figure for more information.
Vigor2130 Series User’s Guide 190 harder for unauthorized clients or STAs to join your wireless LAN. SSID- It means the identification of the wireless LAN. SSID can be any text numbers or various special characters. The default SSID is "DrayTek".
Vigor2130 Series User’s Guide 191 Each encryption mode will bring out different web page and ask you to offer additional configuration. Click OK to save the settings.
Vigor2130 Series User’s Guide 192 126(~) except '#' and ',' . Authentication Mode Choose OPEN or SHARE D as the authentication mode. OPEN: Set wireless to authentication open mode. SHARED: Set wireless to authentication shared mode.
Vigor2130 Series User’s Guide 193 Available settings are explained as follows: Item Description Type The WPA encrypts each frame transmitted from the radio using the key, which either PSK (Pre-Shared Key) entered manually in this field below or automatically negotiated via 802.
Vigor2130 Series User’s Guide 194 Available settings are explained as follows: Item Description Configure via Push Button Click Start PBC to invoke Push-Button style WPS setup procedure. The router will wait for WPS requests from wireless clients about two minutes.
Vigor2130 Series User’s Guide 195 of a station with network card installed, press Start PBC button of network card. If you want to use PIN code, you have to know the PIN code specified in wireless client. Then provide the PIN code of the wireless clie nt you wish to connect to the vigor router.
Vigor2130 Series User’s Guide 196 4 4 . . 1 1 0 0 . . 3 3 A A c c c c e e s s s s C C o o n n t t r r o o l l For additional security of wireless access, the Access Control facility allows you to restrict the network access right by controlling the wire less LAN MAC address of client.
Vigor2130 Series User’s Guide 197 4 4 . . 1 1 0 0 . . 4 4 S S t t a a t t i i o o n n L L i i s s t t Station List provides the knowledge of connecting wire less clients now along with its status code. Available settings are explained as follows: Item Description Auto-refresh Check this box to force the system refreshing the table automatically .
Vigor2130 Series User’s Guide 198 4 4 . . 1 1 0 0 . . 5 5 A A c c c c e e s s s s P P o o i i n n t t D D i i s s c c o o v v e e r r y y Vigor router can scan all regulatory channels and find working APs in the neighborhood. Based on the scanning result, users will know which channel is clean for usage.
Vigor2130 Series User’s Guide 199 4 4 . . 1 1 0 0 . . 6 6 W W M M M M C C o o n n f f i i g g u u r r a a t t i i o o n n WMM is an abbreviation of Wi-Fi Multimedia. It defines the priority levels for four access categories derived from 802.1d (prioritization tabs).
Vigor2130 Series User’s Guide 200 be smaller; however, the difference between AC_BE and AC_BK categories must be greater. Txop It means transmission opportunity. For WMM categories of AC_VI and AC_VO that need higher priorities in data transmission, please set greater value for them to get highest transmission opportunity.
Vigor2130 Series User’s Guide 201 4 4 . . 1 1 0 0 . . 7 7 W W D D S S WDS means Wireless Distribution System. It is a protocol for connecting two access points (AP) wirelessly. Usually, it can be used for the following application: y Provide bridge traffic between two LANs through the air.
Vigor2130 Series User’s Guide 202 In Bridge mode, the router will connect to up to four Vigor2130 which use the sam e mode, and all wired Ethernet clients of every Vigor21 30 will be connected together. You can use this mode to connect a network to other networks which is physically isolated.
Vigor2130 Series User’s Guide 203 to be entered in this page at one time. Phy Mode There are three types of transmission rates developed by different techniques for Phy Mode . Data will be transmitted via communication channel. CCK – If 802.11b wireless mode is used, please choose such type as the Phy Mode.
Vigor2130 Series User’s Guide 204 Item Description Safely Remove Disk Check this box and then you can remove the USB disk safely. Manufacturer Display the manufacturer of the disk. Model Display the type of the disk. Size Display the storage space of the disk.
Vigor2130 Series User’s Guide 205 4 4 . . 1 1 1 1 . . 3 3 F F i i l l e e E E x x p p l l o o r r e e r r To review the content of USB diskette via USB port of the router, please open USB Application Explorer to browse the files. Available settings are explained as follows: Item Description Refresh Click this icon to refresh files list.
Vigor2130 Series User’s Guide 206 4 4 . . 1 1 1 1 . . 4 4 F F T T P P U U s s e e r r M M a a n n a a g g e e m m e e n n t t This page allows you to change user setting for USB storage disk. Before m odifying settings in this page, please insert a USB disk and configure settings in User>>User Configuration first.
Vigor2130 Series User’s Guide 207 Home Folder It determines the range for the client to access into. The user can enter a directory name in this field.
Vigor2130 Series User’s Guide 208 Visible It displays the status of the connected USB disk. To add a new entry for disk sharing, please click Add a New Entry to open the following page. Available settings are explained as follows: Item Description Share Name Type a name to be known by other computers in local network.
Vigor2130 Series User’s Guide 209 All Users Read-only - everyone has read-only access to the share disk. All Users Read-write - every one has read-write access to the share disk. Specific Users – Only specific user(s) c an access into the share disk.
Vigor2130 Series User’s Guide 210 Available settings are explained as follows: Item Description BT Function Enable – Click it to enable BT download function after powering your computer. Disable – Click it to disable BT download function after powering your computer Start – Start the BT download process.
Vigor2130 Series User’s Guide 211 Password Type a password for authentication. Web Client Port Type a port number for accessing Open Web Client. Remote Management Enable – Click it to enable rem ote control for BT torrent download. Disable – Click it to disable remote management function.
Vigor2130 Series User’s Guide 212 Available settings are explained as follows: Item Description iTunes Server Enable – Click it to enable iTunes Server function. Disable – Click it to disable iTunes Server function. Server Name The default name is the router name.
Vigor2130 Series User’s Guide 213 Available settings are explained as follows: Item Description DLNA Server Enable – Click it to enable DLNA Server function. Disable – Click it to disable DLNA Server function. Server Name The default name is the router name.
Vigor2130 Series User’s Guide 214 Available settings are explained as follows: Item Description Enable Temperature Sensor Enable – Enable the function of temperature sensor. Disable – Disable the function. Display Unit Choose the display unit of the temperature.
Vigor2130 Series User’s Guide 215 4 4 . . 1 1 2 2 V V o o I I P P Note: This function is used for “V” models. Voice over IP network (VoIP) enables you to use your broadband Internet connection to ma ke toll quality voice calls over the Internet.
Vigor2130 Series User’s Guide 216 The major benefit of this mode is that you don’t have to memorize your friend’s IP address, which might change very frequently if it’s dynam ic. Instead of that, you will only have to using dial plan or directly dial your friend’s account name if you are with the same SIP Registrar.
Vigor2130 Series User’s Guide 217 Click any index number to display the dial plan setup page. Available settings are explained as follows: Item Description Enable Click this to enable this entry. Phone Number The speed-dial number of this index. This can be any number you choose, using digits 0-9 and * .
Vigor2130 Series User’s Guide 218 the same SIP server, sometimes, the VoIP phone call connection may not succeed. By using the specified dial out account, the successful connection can be assured. After finished the above configuration, click OK to save the settings and exit this page.
Vigor2130 Series User’s Guide 219 SIP server. OP Number The front number you ty pe here is the first part of the account number that you want to execute special function (according to the chosen mode) by using the prefix number. Min Len Set the minimal length of the dial num ber for applying the prefix number settings.
Vigor2130 Series User’s Guide 220 4 4 . . 1 1 1 1 . . 1 1 . . 3 3 C C a a l l l l B B a a r r r r i i n n g g Call barring is used to block phone calls coming from the one that is not welcomed. Click any index number to display the dial plan setup page.
Vigor2130 Series User’s Guide 221 Specific URI/URL or Specific Number This field will be changed based on the type you selected for barring Type. Interface All means all the phone calls will be blocked with such mechanism. After finished the above configuration, click OK to save the settings and exit this page.
Vigor2130 Series User’s Guide 222 4 4 . . 1 1 2 2 . . 1 1 . . 4 4 R R e e g g i i o o n n a a l l This page allows you to process incoming or out going phone calls by regional. Default values (common used in most areas) will be shown on this web page.
Vigor2130 Series User’s Guide 223 end. Hide caller ID [Deact] Dial the number typed in this field to release this function. Call Waiting [Act] Dial the number typed in this field to make all the incoming calls waiting for your answer. Call Waiting [Deact] Dial the number typed in this field to release this function.
Vigor2130 Series User’s Guide 224 Ring Port Specify which port will ring when receiving a phone call. Status Show the status for the corresponding SIP account. R means such account is registered on SIP server successfully. – means the account is failed to register on SIP server.
Vigor2130 Series User’s Guide 225 SIP Port Set the port number for sending/receiving SIP message for building a session. The default value is 5060. Your peer must set the same value in his/her Registrar. Domain/Realm Set the domain name or IP address of the SIP Registrar server.
Vigor2130 Series User’s Guide 226 4 4 . . 1 1 2 2 . . 3 3 P P h h o o n n e e S S e e t t t t i i n n g g s s This page allows user to set phone settings fo r Phone 1 and Phone 2 respectively. However, it changes slightly according to different model you have.
Vigor2130 Series User’s Guide 227 Also, you can specify each field for your necessity. It is recommended for you to use the default settings for VoIP communication.
Vigor2130 Series User’s Guide 228 D D e e t t a a i i l l e e d d S S e e t t t t i i n n g g s s f f o o r r P P h h o o n n e e P P o o r r t t Click the number link for Phone port, you can access into t he following page for configuring Phone settings.
Vigor2130 Series User’s Guide 229 notice sound will appear to tell the user new phone call is waiting for your response. Click hook flash to pick u p the waiting phone call. Call Transfer- Check this box to invoke this function. Click hook flash to initiate anothe r phone call.
Vigor2130 Series User’s Guide 230 In addition, you can press the Advanced button to configure volume gain, MISC and DTMF mode. Advanced setting is provided for fitting the telecommunication custom for the local area of the router installed. Wrong settings might cause inconvenience for users.
Vigor2130 Series User’s Guide 231 tone according to the digital form it receive. This function is very useful when the network traffic congestion occurs and it still can remain the accuracy of DTMF tone. SIP INFO - Choose this one then the Vigor will capture the DTMF tone and transfer it into SIP form.
Vigor2130 Series User’s Guide 232 PeerID The present in-call or out-call peer ID (the format may be IP or Domain). Elapse The format is represented as hours:minutes:seconds. Tx Pkts Total number of transmitted voice packets during this connection session.
Vigor2130 Series User’s Guide 233 L L i i n n k k - - L L o o c c a a l l O O n n l l y y Link-Local address is used for communicating with neighbouring nodes on the sam e link. It is defined by the address prefix fe80::/10 . You don't need to setup Link-Local address manually for it is generated automatically according to your MAC Address.
Vigor2130 Series User’s Guide 234 Available settings are explained as follows: Item Description IPv6 Address Type your IPv6 static IP here. Prefix Length Type y our IPv6 address prefix length here. Gateway IPv6 Server Type your IPv6 gateway address here.
Vigor2130 Series User’s Guide 235 Item Description SLA Length It is used by an individual organization to create its own local addressing hierarchy and to identify subnets. T T S S P P C C Tunnel setup protocol client (TSPC) is an applica tion which could help you to connect to IPv6 network easily.
Vigor2130 Series User’s Guide 236 IPv6-in-IPv4 (Native) - Request an IPv6 in IPv4 tunnel. IPv6-in-IPv4 (NAT Traversal - Request an IPv6 in UDP of IPv4 tunnel (for clients behind a NAT). Auto-reconnect Delay After passing the time set here, the client will retry to connect in case of failure or keepalive timeout.
Vigor2130 Series User’s Guide 237 from other ISP, such as http://www.sixxs.net/ . Password Type the password assigned with the user name. Confirm Password Type the password again to make the confirmation. Server Type the default server address, tic.
Vigor2130 Series User’s Guide 238 Item Description IPv6 Link local Address - It is used for communicating with neighbouring nodes on the same link. It is defined by the address prefix fe80::/10. You don't need to setup Link-Local address manually for it is generated automatically according to your MAC Address.
Vigor2130 Series User’s Guide 239 A A d d d d i i n n g g a a N N e e w w R R u u l l e e Click Add New Rule to configure a new rule for IPv6 Firewall. Note: You can set up to 20 sets of IPv6 rules. Available settings are explained as follows: Item Description Name Type a name for the rule.
Vigor2130 Series User’s Guide 240 Item Description Destination IP / Choose PC Type the IP address here if you choose Single as Destination IP Type . Or click Choose PC to select an Ipv6 address. Destination Subnet/ Choose Subnet Type the subnet mask here if you choose Subnet as Destination IP Type .
Vigor2130 Series User’s Guide 241 In the following dialog, please configure the page with the following values. 5. Connect PC to http://www.ipv6.org/ with IPv6 IP address again. A message will appear from web page: Welcome to the IPv6 Information Page! You are using IPv4 from 114.
Vigor2130 Series User’s Guide 242 4 4 . . 1 1 3 3 . . 4 4 I I P P v v 6 6 R R o o u u t t i i n n g g This page displays the routing table for the protocol of IPv6. Each item is explained as follows: Item Description Device Display the interface name (eth0, eth1, fp, etc.
Vigor2130 Series User’s Guide 243 4 4 . . 1 1 3 3 . . 5 5 I I P P v v 6 6 N N e e i i g g h h b b o o u u r r IPv6 uses neighbor discovery protocol to find out neighbors on the same link. Each item is explained as follows: Item Description Device The interface name of the link where the neighbor is on.
Vigor2130 Series User’s Guide 244 4 4 . . 1 1 3 3 . . 6 6 I I P P v v 6 6 T T S S P P C C S S t t a a t t u u s s IPv6 TSPC status web page could help you to diagnose the connection status of TSPC. TSPC log contains some debug information from program.
Vigor2130 Series User’s Guide 245 Each item is explained as follows: Item Description Connection Status It will bring out different pages to represent IPv6 disconnection, connecting and connected.
Vigor2130 Series User’s Guide 246 When your PC obtains the IPv6 address, please connect to http://www.ipv6.org . If your PC access Internet via IPv6 connection, your IP v6 address will be shown on the web page immediately. Refer to the following figure.
Vigor2130 Series User’s Guide 247 4 4 . . 1 1 3 3 . . 7 7 I I P P v v 6 6 M M a a n n a a g g e e m m e e n n t t This page allows you to manage the settings for IPv6 access control including settings of HTTP, HTTPs, SSH, FTP and TELNET by using IPv6 protocol.
Vigor2130 Series User’s Guide 248 4 4 . . 1 1 4 4 U U s s e e r r 4 4 . . 1 1 4 4 . . 1 1 U U s s e e r r C C o o n n f f i i g g u u r r a a t t i i o o n n This page allows you to set user’s setti ng that allowed to use PPTP, FTP, IPSEC/L2TP connection.
Vigor2130 Series User’s Guide 249 Item Description Before enable this function, please install Samba Server first. Allow IPSEC/L2TP Check this box to let the remote user connecting to this device through IPSEC/L2TP . Allow PPTP Check this box to let the remote user connecting to this device through PPTP .
Vigor2130 Series User’s Guide 250 E E d d i i t t i i n n g g / / D D e e l l e e t t i i n n g g U U s s e e r r S S e e t t t t i i n n g g s s To edit a user, click the name link under Userna me to open the following page. M odify the settings except Username and then click OK to save and exit it.
Vigor2130 Series User’s Guide 251 4 4 . . 1 1 5 5 S S y y s s t t e e m m M M a a i i n n t t e e n n a a n n c c e e For the system setup, there are several items that you have to know the way of configuration: Status, User Password, Configuration Backup, Syslog/Mail Alert, Time and Date, Management, Reboot System , and Firmware Upgrade.
Vigor2130 Series User’s Guide 252 System Date Display current time and date for the system server. System Uptime Display the connection time for the system server. System CPU Usage - Display the percentage of the CPU usage of your system. Memory Usage - Display the size of the memory usage and the percentage.
Vigor2130 Series User’s Guide 253 4 4 . . 1 1 5 5 . . 2 2 T T R R - - 0 0 6 6 9 9 Vigor router with TR-069 is available for matching with VigorACS server. Such page provides VigorACS and CPE settings under TR-069 protocol. All the settings configured here is for CPE to be controlled and managed with VigorACS server.
Vigor2130 Series User’s Guide 254 Item Description If the connected CPE does not need to be authenticated please set URL as the following: http://{IP address of VigorACS}:8080/ACSServer/services/UnAuthACSServlet Username/Password - Type userna me and password for ACS Server for authentication.
Vigor2130 Series User’s Guide 255 password is blank. New Password Type in new password in this filed. Confirm Password Type in the new password again. When you click OK , the login window will appear. Please use the new password to access into the web configurator again.
Vigor2130 Series User’s Guide 256 3. Log out Vigor2130 Web Configurator. 4. The following window will be open to ask for username and password. Type the new user password in the filed of Password and click Login .
Vigor2130 Series User’s Guide 257 5. The main screen with User M ode will be shown as follows. Settings to be configured in User Mode will be less than settings in Admin Mode.
Vigor2130 Series User’s Guide 258 3. In Save As dialog, the default filename is config.cfg . You could gi ve it another name by yourself. 4. Click Save button, the configuration will download a utomatically to your computer as a file named config.cfg .
Vigor2130 Series User’s Guide 259 2. Click Browse button to choose the correct configura tion file for uploading to the r outer. 3. Click Restore button and wait for few seconds, the following picture will tell you that the restoration procedure is successful.
Vigor2130 Series User’s Guide 260 User Access Log - Check this box to record the user logging information. Mail Alert Setup Enable - Check “ Enable ” to activate function of mail alert. Send a Test e-mail – Click this button to let the system send a test e-mail to the specified e-mail address.
Vigor2130 Series User’s Guide 261.
Vigor2130 Series User’s Guide 262 4 4 . . 1 1 5 5 . . 7 7 T T i i m m e e a a n n d d D D a a t t e e It allows you to specify where the time of the router should be inquired from. Available settings are explained as follows Item Description Time Information Current Syst em Time - Display current time in the box.
Vigor2130 Series User’s Guide 263 4 4 . . 1 1 5 5 . . 8 8 M M a a n n a a g g e e m m e e n n t t This page allows you to manage the setti ngs for access control, access list, port setup, and SMP setup. For example, as to management access control, the port number is used to send/receive SIP message for building a session.
Vigor2130 Series User’s Guide 264 4 4 . . 1 1 5 5 . . 9 9 R R e e b b o o o o t t S S y y s s t t e e m m The Web Configurator may be used to restart your router for using current configuration. Click Reboot System from System Maintenance to open the following page.
Vigor2130 Series User’s Guide 265 Click Browse.. to locate the newest firmware and click Upgrade . During the process of upgrade, do not turn off your router. 4 4 . . 1 1 6 6 D D i i a a g g n n o o s s t t i i c c s s Diagnostic Tools provide a useful way to view or diagnose the status of your Vigor router.
Vigor2130 Series User’s Guide 266 4 4 . . 1 1 6 6 . . 2 2 T T r r a a c c e e R R o o u u t t e e Click Diagnostics and click Trace Route to open the web page. This page allows you to trace the routes from router to the host. Simply type the IP address of the host in the box and click Run .
Vigor2130 Series User’s Guide 267 U - route is up. H - target is a host G - use gateway R - reinstate route for dynamic routing D - dynamically installed by daemon or redirect M - modified from rout.
Vigor2130 Series User’s Guide 268 4 4 . . 1 1 6 6 . . 5 5 S S y y s s t t e e m m L L o o g g Click Diagnostics and click System Log to open the web page. Available settings are explained as follows: Item Description Auto-refresh Check it to enable auto-refresh function.
Vigor2130 Series User’s Guide 269 4 4 . . 1 1 6 6 . . 6 6 T T r r a a f f f f i i c c O O v v e e r r v v i i e e w w This page offers an overvie w of general traffic statis tics for all connecting ports. Each item is explained as follows: Item Description Port Display the interface that data transmission passing through.
Vigor2130 Series User’s Guide 270 4 4 . . 1 1 6 6 . . 7 7 D D e e t t a a i i l l e e d d S S t t a a t t i i s s t t i i c c s s This page display detailed statistics for WAN/LAN interface. Each item is explained as follows: Item Description WAN/LAN Choose WAN or LAN to display the corresponding statistics.
Vigor2130 Series User’s Guide 271 good and bad packets received. RX 65-127 Bytes - Display the number of 65 ~ 127- byte frames in good and bad packets received. RX 128-255 Bytes - Display the number of 12 8 ~ 255-byte frames in good and bad packets received.
Vigor2130 Series User’s Guide 272 good and bad packets transmitted. Tx 65-127 Bytes - Display the number of 65 ~ 127- byte frames in good and bad packets transmitted. Tx 128-255 Bytes - Display the number of 128 ~ 25 5-byte frames in good and bad packets transmitted.
Vigor2130 Series User’s Guide 273 Each item is explained as follows: Item Description Auto-refresh Check it to enable auto-refresh function. Refresh Click it to reload the page. Clear Click it to clear the counters for all ports. Type Indicate whether the entry is a static or dynamic entry.
Vigor2130 Series User’s Guide 274 Refresh Click it to reload the page. Computer Name It displays the name of the computer accepted the assigned IP address by this router. IP Address It displays the IP address assigned by this router for specified PC.
Vigor2130 Series User’s Guide 275 TX rate (kbps) Display the transmission speed of the monitored device. RX rate (kbps) Display the receiving spee d of the monitored device. Hardware NAT rate Display the data processing rate of the monitored device if hardware NAT is enabled.
Vigor2130 Series User’s Guide 276 The horizontal axis represents time. Yet the vertical axis has different meanings. For WAN1 Bandwidth chart, the numbers displayed on ve rtical axis represent the numbers of the transmitted and received packets in the past.
Vigor2130 Series User’s Guide 277 conditions specified. Clear Clear all of the information displayed in this page. 4 4 . . 1 1 6 6 . . 1 1 3 3 P P o o r r t t s s S S t t a a t t e e Click Diagnostics and click Ports State to open the list page. There are for LAN ports and one WAN port in your router.
Vigor2130 Series User’s Guide 278 This page is left blank..
Vigor2130 Series User’s Guide 279 T T r r o o u u b b l l e e S S h h o o o o t t i i n n g g This section will guide you to solve abnormal s ituations if you cannot access into the Internet after installing the router and finishing the we b configuration.
Vigor2130 Series User’s Guide 280 5 5 . . 2 2 C C h h e e c c k k i i n n g g I I f f t t h h e e N N e e t t w w o o r r k k C C o o n n n n e e c c t t i i o o n n S S e e t t t t i i n n g g s s .
Vigor2130 Series User’s Guide 281 4. Select Obtain an IP address automatically and Obtain DNS server address automatically . F F o o r r M M a a c c O O S S 1. Double click on the current used Mac OS on the desktop. 2. Open the Application folder and get into Network .
Vigor2130 Series User’s Guide 282 5 5 . . 3 3 P P i i n n g g i i n n g g t t h h e e R R o o u u t t e e r r f f r r o o m m Y Y o o u u r r C C o o m m p p u u t t e e r r The default gateway IP address of the router is 192.168.1.1. For some reason, you might need to use “ping” command to check the link status of the router.
Vigor2130 Series User’s Guide 283 5 5 . . 4 4 C C h h e e c c k k i i n n g g I I f f t t h h e e I I S S P P S S e e t t t t i i n n g g s s a a r r e e O O K K o o r r N N o o t t Open WAN>>Internet Access page and then check whether the ISP settings are set correctly.
Vigor2130 Series User’s Guide 284 5 5 . . 5 5 F F o o r r c c i i n n g g V V i i g g o o r r R R o o u u t t e e r r i i n n t t o o T T F F T T P P M M o o d d e e f f o o r r P P e e r r f f o o r r m m i i n n g g t t h h e e F F i i r r m m w w a a r r e e U U p p g g r r a a d d e e 1.
Vigor2130 Series User’s Guide 285 12. When the firmware upgrade is successf ul, the following window will pop up..
Vigor2130 Series User’s Guide 286 If the message of Request Timeout. Transfer Abort ! appears, please check if the connection between the computer and the Vigor is active or not. And, if the message of Incorrect/No file name. Transfer Abort ! appears, please check if the firmware you download is correct for your Vigor router.
Vigor2130 Series User’s Guide 287 5 5 . . 6 6 B B a a c c k k i i n n g g t t o o F F a a c c t t o o r r y y D D e e f f a a u u l l t t S S e e t t t t i i n n g g I I f f N N e e c c e e s s s s a a r r y y Sometimes, a wrong connection can be im proved by returning to the default settings.
Vigor2130 Series User’s Guide 288 5 5 . . 7 7 C C o o n n t t a a c c t t i i n n g g Y Y o o u u r r D D e e a a l l e e r r If the router still cannot work correctly after trying many efforts, please contact your dealer for further help right away.
Ein wichtiger Punkt beim Kauf des Geräts Draytek Vigor2130n (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Draytek Vigor2130n noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Draytek Vigor2130n - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Draytek Vigor2130n reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Draytek Vigor2130n erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Draytek Vigor2130n besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Draytek Vigor2130n verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Draytek Vigor2130n. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Draytek Vigor2130n gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
