Benutzeranleitung / Produktwartung 2006 DR Ram SRT-10 des Produzenten Dodge
Zur Seite of 384
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE .............................. 7 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ...........
.
INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 䡵 How T o Use This Manual .................. 4 䡵 W arnings And Cautions ................... 5 䡵 V an Conversions/Campers ................. 5 䡵 V ehicle Identification Number .
INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a W arranty Information Booklet and various customer oriented documents.
W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es which could result in an accident or bodily injury . It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entir e manual you may miss important information.
NOTE: It is illegal to remove the VIN plate. VEHICLE MODIFICA TIONS / AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys .................. 1 0 ▫ Key-In-Ignition Reminder ................ 1 0 ▫ Sentry Key — If Equipped ................ 1 0 䡵 Ignition And Steering Lock — If Equipped .
䡵 Security Alarm System — If Equipped ......... 2 0 ▫ Rearming Of The System ................. 2 0 ▫ T o Set The Alarm ...................... 2 0 ▫ T o Disarm The System ................... 2 0 䡵 W indows ............................. 2 1 ▫ Power W indows—If Equipped .
䡵 Safety T ips ............................ 6 8 ▫ T ransporting Passengers ................. 6 8 ▫ Lock Y our V ehicle ...................... 6 8 ▫ Exhaust Gas .......................... 6 9 ▫ Safety Checks Y ou Should Make Inside The V ehicle .
A WORD ABOUT YOUR KEYS The double sided keys may be inserted into the locks with either side up. The keys for your new vehicle are enclosed in a plastic bag with a bar code label affixed to the front. The bar code can be used to or der duplicate keys from your dealer or a locksmith.
The ⬙ Security Light ⬙ , located in the instrument cluster , will illuminate for about 3 seconds when the ignition switch is first turned to the ON position. If the vehicle electronics do not r eceive a valid signal from the ignition key , the ⬙ Security Light ⬙ will flash continuously to signal that the vehicle has been immobilized.
2. Insert the second valid key and switch the ignition to the ON position within 15 seconds. After 10 seconds the ⬙ Security Light ⬙ will begin to flash.
IGNITION AND STEERING LOCK — IF EQUIPPED Manual T ransmissions Depress and hold the r elease button located between the ignition switch and the instrument panel. T urn the igni- tion key to LOCK and remove the key . DOOR KEY The same key used to start the vehicle is also used to unlock the doors.
W ARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal inju- ries and death.
Automatic Door Locks If this feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph. This feature is enabled when your vehicle is shipped from the assembly plant and can be disabled by using the following procedur e: 1.
REMOTE KEYLESS ENTR Y — IF EQUIPPED This system allows you to lock or unlock the doors from distances up to about 23 feet (7 meters) using a hand held radio transmitter .
5. This will enable you to unlock all doors on the first press of the UNLOCK button. T o lock the doors: Press and r elease the LOCK button on the transmitter to lock all doors. If the ignition is OFF , when the doors are locked, the parking lights will flash on once and the horn will chirp once.
4. T o reactivate this featur e, repeat the above steps. Using the Panic Alarm T o activate the Panic mode while the ignition is OFF press and release the P ANIC button on the transmitter once. When the Panic mode is activated, the interior lights will illuminate, the headlamps and parking lights will flash, and the horn will sound.
2. Closeness to a radio transmitter such as a radio station tower , airport transmitter , and some mobile or CB radios. T ransmitter Battery Service The recommended r eplacement battery is a 3V lithium 2016 cell. This transmitter requir es two batteries.
SECURITY ALARM SYSTEM — IF EQUIPPED This system monitors the vehicle doors and ignition for unauthorized operation. When the alarm is activated, the system provides both audible and visual signals. For the first 3 minutes the horn will sound and the headlights and security telltale will flash repeatedly .
horn will sound three times when you unlock the doors and the security lamp will flash for 30 seconds. Check the vehicle for tampering. The Security system will also disarm, if the vehicle is started with a programmed Sentry Key .
The control on the left fr ont door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window contr ol. The windows will operate only when the ignition switch is turned to the ON or ACC (Accessory) position.
W indow Lockout Switch (4 Door Models Only) The window lockout switch on the driver’s door allows you to disable the window control on the other doors. T o disable the window controls on the other doors, pr ess the window lock button. T o enable the window controls, press the window contr ol button again.
Sliding Rear Window A locking device in the center of the window helps to prevent entry fr om the rear of the vehicle. Squeeze the lock to release the window . WIND BUFFETING W ind buffeting can be described as the perception of pressur e on the ears or a helicopter type sound in the ears.
W ARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. Y ou can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly .
W ARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door . Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt.
W ARNING! • A belt buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
W ARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos- sible and keep it snug. • A twisted belt can’t do its job as well.
Standard Cab Front Center Three Point Belt 1. The front center seat belt on the Standard Cab may be disconnected to open up utilization of the storage areas behind the front seats. The black latch plate can be detached from the black keyed seat belt buckle located on the inboard side of the passenger seat.
W ARNING! • If the black latch and black buckle are not prop- erly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision. • When reattaching the black latch and black buckle, ensure the seat belt webbing is not twisted.
W ARNING! If the black latch and buckle are not connected when the seat belt is used by an occupant, the seat belt will not restrain you properly . Adjustable Upper Shoulder Belt Anchorage In the front r ow outboard seats, the shoulder belt can be adjusted upward or downwar d to help position the belt away from your neck.
As a guide, if you are shorter than average, you will prefer a lower position, and if you ar e taller than average, you’ll prefer a higher position. When you r elease the anchorage, try to move it up or down to make sure that it is locked in position.
3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
NOTE: These devices are not a substitute for pr oper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly . The pretensioners ar e triggered by the airbag contr ol module. Like the airbags, the pretensioners ar e single use items.
3. W ithin 60 seconds of turning the ignition switch to the ON position, unbuckle and then re-buckle the driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled. NOTE: W atch for the Seat Belt W arning Light to turn on while unbuckling and off while r e-buckling the seat belt.
W ARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use the seat belt extender when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed.
NOTE: The front airbags ar e certified to the Federal regulations that allow less for ceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have differ ent rates of inflation that are based on collision severity and occupant size.
Along with the seat belts, front airbags work with the instrument panel knee bolsters to pr ovide improved protection for the driver and fr ont passenger . W indow bags also work with seat belts to improve occupant protection. The seat belts are designed to pr otect you in many types of collisions.
4. If your vehicle has window bags, do not lean against the door or window , airbags will inflate forcefully into the space between you and the door . 5. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center .
Air Bag System Components The airbag system consists of the following: • Occupant Restraint Controller • Side Remote Acceleration Sensors (If Equipped) • Airbag W arning Light • Driver Airbag .
How the Airbag System W orks • The Occupant Restraint Controller (ORC) determines if a frontal collision is sever e enough to requir e the airbags to inflate. The front airbag inflators ar e de- signed to provide dif ferent rates of airbag inflation from dir ection provided by the ORC.
• If your vehicle is equipped with an Occupant Classi- fication System (OCS), the sun visor air bag warning label will have the phrase ⬙ even with advanced air bags ⬙ on it.
For almost all properly installed r ear facing child re- straints, the P AD indicator light (If Equipped) will be illuminated indicating that the front passenger airbag is turned off and will not inflate. If the P AD indicator light is not illuminated, DO NOT assume the air bag is turned off and move the child r estraint to the second row of seats.
on the seat will also be sensed. The weight of an adult will cause the system to turn the airbag on. In this case, the OCS has classified the occupant of the seat as an adult. An adult occupant needs to sit in a normal position (with their feet on or near the floor) in order to be properly classified.
airbag is turned off until the fault is clear ed. If an object is lodged under the seat and interferes with operation of the weight sensors, a fault will occur which turns on both the P AD Indicator Light (If Equipped) and the Airbag W arning Light.
• Y our vehicle has four W eight Sensors (If Equipped) located between the seat and the floor pan. The weight sensors measure applied weight and transfers that information to the OCM. • The Side Impact SRS W indow Bags are designed to activate only in certain side collisions.
• Do not use prior or future model year seat covers not designated for the specific model being repair ed. Al- ways use the correct seat cover specified for the vehicle. • Do not replace the seat cover with an aftermarket seat cover . • Do not add a secondary seat cover other than those approved by DaimlerChrysler/Mopar .
Passenger Airbag On/Off Switch – (Standard Cab V ehicles Only) The passenger front airbag is to be turned of f only if the passenger: • is an infant (less than 1 year old) who must ride in the fro.
W ARNING! Whenever an airbag is turned off, even a lap/ shoulder belted passenger may hit their head, neck, or chest on the dashboard (instrument panel) or windshield in a crash.
If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and fr ont passenger as the airbags deploy and unfold.
Maintaining Y our Airbag System W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. Y ou could be injured if the airbag system is not there to protect you.
• The light remains on or flickers after the 6 to 8 second interval. • The light flickers or comes on and remains on while driving. NOTE: If the speedometer , tachometer or any engine related gauges ar e not working, the airbag control mod- ule may also be disabled.
provided to the custodial entity upon r equest. General data that does not identify particular vehicles or crashes may be released for incorporation in aggr egate crash databases, such as those maintained by the US govern- ment and various states.
Child Restraint Everyone in your vehicle needs to be buckled up all the time — babies and children, too. Every state in the United States and all Canadian provinces r equire that small children ride in pr oper restraint systems. This is the law , and you can be prosecuted for ignoring it.
Infants and Small Children There ar e differ ent sizes and types of restraints for children fr om newborn size to the child almost large enough for an adult safety belt.
• The belt-positioning booster seat is for children weigh- ing more than 40 lbs (18 kg), but who ar e still too small to fit the vehicle’s seat belts properly . If the child cannot sit with knees bent over the vehicle’s seat cushion while the child’s back is against the seat back, they should use a belt-positioning-booster seat.
Here are some tips for getting the most out of your child restraint: • Before buying any r estraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. W e also recommend that you make sure that you can install the child restraint in the vehicle where you will use it befor e you buy it.
• If the belt still can’t be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secur e, try a differ ent seating position.
Identification dots are located above the standar d cab front seat lower anchorages as a guide for locating lower anchors. NOTE: For children riding in the fr ont seat of a Stan- dard Cab model r efer to the “Passenger Airbag On/Off Switch” located in this section.
Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seatback tether anchorage have been available for some time.
Installing the Child Restraint System W ARNING! Do not install child restraint systems equipped with LA TCH attachments in the center position of a Quad Cab model rear seat. The LA TCH anchorages in this seat are designed for the two outboard seating posi- tions only .
W ARNING! Improper installation of a child restraint to the LA TCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
2. Lift the cover (if so equipped), and attach the hook to the square opening in the sheet metal. 3. Install the child restraint and remove the slack in the tether strap according to the manufactur er’s instructions. Multiple Child Restraint Installation Sequence - (Quad Cab Rear Seats) 1.
5. Place a child restraint on the center rear seat and adjust the tether strap so that it will reach under the head restraint to the tether anchor dir ectly behind the seat and to the anchor directly behind the right seat.
Quad Cab T ether Strap Mounting 66 THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE.
Children T oo Large for Booster Seats Children who ar e large enough to wear the shoulder belt comfortably , and whose legs are long enough to bend over the front of the seat when their back is against the seat back should use the lap/shoulder belt in a rear seat.
• Check the engine oil level at every fuel fill. NOTE: A new engine will consume some oil during the first few thousand miles of operation. This should be considered as a normal part of the br eak-in and not interpreted as a sign of dif ficulty . SAFETY TIPS T ransporting Passengers This vehicle is designed to carry passengers in the cab only .
Exhaust Gas W ARNING! Exhaust gases contain carbon monoxide, a poten- tially toxic gas that by itself is colorless and odorless. T o avoid inhaling these gases, the following precau- tions should be observed: • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
Safety Checks Y ou Should Make Inside The V ehicle Seat Belts Inspect the belt system periodically , checking for cuts, frays and loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor , torn webbing, etc.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Hands–Free Communication (UConnect™) — If Equipped ............................ 7 6 ▫ Operations ........................... 7 7 ▫ Phone Call Features .................... 8 4 ▫ UConnect™ System Features .
▫ Headlamp Delay ...................... 1 0 8 ▫ Headlights, Parking Lights, Panel Lights ..... 1 0 8 ▫ Daytime Running Lights (Canada Only And Fleet V ehicles) .......... 1 0 9 ▫ Lights-On Reminder ................... 1 1 0 ▫ Fog Lights — If Equipped .
▫ US/M Button ........................ 1 2 1 ▫ Reset Button ......................... 1 2 1 ▫ Global Reset ......................... 1 2 2 ▫ Step Button ......................... 1 2 2 ▫ A verage Fuel Economy (A VG ECO) ........ 1 2 2 ▫ Distance T o Empty (DTE) .
▫ V enting Sunroof - Express ............... 1 3 5 ▫ Sunshade Operation ................... 1 3 5 ▫ W ind Buffeting ....................... 1 3 6 ▫ Sunroof Maintenance ................... 1 3 6 ▫ Sunroof Fully Closed ................... 1 3 6 䡵 Electrical Power Outlets .
䡵 T onneau Cover Removal — If Equipped ...... 1 5 2 䡵 Mirrors .............................. 1 5 7 ▫ Automatic Dimming Mirror— If Equipped . . . 157 ▫ Outside Mirrors ...................... 1 5 7 ▫ Exterior Mirrors Folding Featur e .....
HANDS–FREE COMMUNICA TION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in- vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone using simple voice commands (e.g., ⬙ Call” ѧ “Mike” ѧ ”W ork ⬙ or ⬙ Dial” ѧ “248-555-1212 ⬙ ).
access the system. The diagram below shows the mirror with the appropriate buttons. Individual button behavior is discussed in the ⬙ Operation ⬙ section. The UConnect™ system can be used with any Hands- Free Pr ofile certified Bluetooth™ cellular phone.
• Prior to giving a voice command, one must wait for the voice on beep, which follows the ⬙ Ready ⬙ prompt or another prompt. • For certain operations, compound commands can be used. For example, instead of saying ⬙ Setup ⬙ and then ⬙ Phone Pairing, ⬙ the following compound command can be said: ⬙ Setup Phone Pairing.
Pair (Link) UConnect™ System to a Cellular Phone T o begin using your UConnect™ system, you must pair your compatible Bluetooth™ enabled cellular phone (re- fer to ⬙ Introduction ⬙ section to learn about the phone type). T o complete the pairing process, you will need to refer ence your cellular phone owner’s manual.
• For identification purposes, you will be prompted to give the UConnect™ system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • Y ou will then be asked to give your cellular phone a priority level between 1 and 7, 1 being the highest priority .
Call by Saying a Name • Press the “Phone” button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Call. ⬙ • System will prompt you to say the name of the person you want call. • After the ⬙ Ready ⬙ prompt and the following beep, say the name of the person you want to call.
After you are finished adding an entry into the phone- book, you will be given the opportunity to add more phone numbers to the current entry or to r eturn to the main menu. The UConnect™ system will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations.
Delete Entries in the UConnect™ Phonebook NOTE: Editing phonebook entries is recommended when vehicle is not in motion. • Press the ’Phone’ button to begin.
• After confirmation, the phonebook entries will be deleted. List All Names in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Phonebook List Names. ⬙ • The UConnect™ system will play the names of all the phonebook entries.
Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in pr ogress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your cell phone. Press the ’Phone’ button to place the curr ent call on hold and answer the incoming call.
Conference Call When two calls are in pr ogress (one active and one on hold), press and hold the ’Phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call.
• After ignition key is switched to off, a call can continue on the UConnect™ system for certain duration, after which the call is automatically transferred fr om the UConnect™ system to the mobile phone. • An active call is automatically transferred to the mobile phone after ignition key is switched to off.
• After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Emergency ⬙ and the UConnect™ system will instr uct the paired cellular phone to call the emer gency num- ber .
Paging T o learn how to page, refer to section ⬙ W orking with Automated Systems. ⬙ Paging works properly except for pagers of certain companies which time-out a little too soon to work properly with the UConnect™ system. V oice Mail Calling T o learn how to access your voice mail, refer to section ⬙ W orking with Automated Systems.
T urning Confirmation Prompts On/Off T urning confirmation prompts of f will stop the system from confirming your choices (e.g. the UConnect™ sys- tem will not repeat a phone number befor e you dial it). • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Confirmations.
Mute/Un-mute (Mute off) When you mute the UConnect™ system, you will still be able to hear the conversation coming from the other party , but the other party will not be able to hear you. In order to mute the UConnect™ system: • Press the ’V oice Recognition’ button.
If you would like to connect or disconnect the Blue- tooth™ connection between a UConnect™ paired cellular phone and the UConnect™ system, follow the instruction described in your cellular phone user’s manual. List Paired Cellular Phone Names • Press the ’Phone’ button to begin.
• The selected phone will be used for the next phone call. If the selected phone is not available, the UCon- nect™ system will return to using the highest priority phone present in or near (appr oximately with in 30 feet) the vehicle. Delete UConnect™ Paired Cellular Phones • Press the ’Phone’ button to begin.
• low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English, French, and Spanish ac- cents, the system may not always work for some.
• smooth road surface, • fully closed windows, and • dry weather condition. • Operation from driver seat. • Performance, such as, audio clarity , echo. and loud- ness to a large degr ee, rely on the phone and network, and not the UConnect™ system.
96 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 97 3.
98 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
North American English Primary Alternate(s) Zero Oh Add location Add new All All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return.
W ARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
The power seat controls ar e on the outboard side of the front seat cushions. One switch contr ols the seat move- ment. The six-way switch can be moved forward or back- wards to get the most comfortable position. The same switch can be moved up and down to control seat height or to change the seat angle by tilting it up or down.
Manual Passenger Seat The passenger seat is adjustable forward or backwar d and is equipped with a back recliner . Manual Seatback Recline The recliner handle is on the outside of the seat cushion. Pull up on the handle, as shown, to release the seat back and adjust for comfort.
W ARNING! Y ou can be seriously , even fatally , injured riding in a seat with the seatback reclined. Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. If you ride in this position, the shoulder harness will no longer be restraining you.
Heated Seats — If Equipped The heated seat switches are located in the instr ument panel under the climate controls. Each heated seat switch has two settings (HI and LOW). Press the switch once to obtain High heat level, then press the switch again to obtain Low heat level.
TO OPEN AND CLOSE THE HOOD T o open the hood, two latches must be released. First pull the hood release lever located below the steering wheel at the base of the instrument panel. Once the hood is released you must r each into the opening beneath the center of the grille and push up the latch to release the safety catch before raising the hood.
W ARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are latched fully before driving.
Interior Lights Courtesy and dome lights are turned on when the fr ont doors are opened, when the dimmer contr ol (rotating wheel on the right side of the switch) is rotated to the upward detent position, or if equipped, when the UN- LOCK button is pressed on the key fob.
Battery Saver T o protect the life of your vehicle’s battery , Load Shed- ding is provided for both the interior and exterior lights. If the ignition is off and any door is left ajar for 10 minutes or the dimmer control is r otated upwards for 10 minutes, the interior lights will automatically turn off.
Y our vehicle is equipped with plastic headlight lenses that are lighter and less susceptible to stone br eakage than glass headlights. Plastic is not as scratch resistant as glass and ther efore differ ent lens cleaning procedur es must be followed.
Lights-on Reminder If the headlights, parking lights, or cargo lights ar e left on, after the ignition is turned off, a chime will sound when the driver’s door is opened.
MUL TIFUNCTION CONTROL LEVER The multifunction control lever is located on the left side of the steering column. T urn Signals Move the lever up or down to signal a right-hand or left-hand turn.
High Beam / Low Beam Select Switch Pull the multifunction control lever fully towar d the steering wheel to switch the headlights from HIGH or LOW beam. Windshield Wipers The wipers and washers are operated by a switch in the multifunction control lever .
Intermittent W iper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the contr ol knob into the upper end of the delay range.
Windshield W ashers T o use the washer , push in on the washer knob on the end of the multifunction control lever and hold while spray is desired. If the washer knob is depr essed while in the delay range, the wiper will operate for several seconds after the washer knob is released.
W ARNING! T ilting the steering column while the vehicle is moving is dangerous. W ithout a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving.
Adjustment 1. Position the driver seat so that you are at least 10 inches (254 mm) away from the airbag located in the center of the steering wheel. 2. Fasten and adjust the seatbelts. 3. Move the adjustable pedal switch, located to the left of the steering column near the parking brake release, in the direction you desir e to move the pedals.
ELECTRONIC SPEED CONTROL When engaged, this device takes over accelerator opera- tion at speeds greater than 35 mph (56 km/h). The controls ar e mounted on the steering wheel. T o Activate Push the ON/OFF button to the ON position. In the instrument cluster , the word “CRUISE” illuminates when the system is on.
W ARNING! Leaving the Speed Control ON when not in use is dangerous. Y ou could accidentally set the system to cause it to go faster than you want. Y ou could lose control and have an accident. Always leave the system OFF when you aren’t using it. T o Resume Speed T o resume a pr eviously set speed, push and release the RESUME button.
for your specific engine), the speed control will automati- cally disengage. If this happens, you can push down on the accelerator pedal to maintain the desired speed. V ehicles equipped with a 6–speed-manual transmission should be operated in 5th gear or lower under the above conditions.
Courtesy/Reading Lights In the middle of the console are two courtesy/r eading lights. Both lights illuminate as courtesy lights when a door is opened, when the dimmer control is r otated to the courtesy light position (fully upward position), or when the UNLOCK button is pressed on the Remote Keyless Entry transmitter , if so equipped.
US/M Button Use this button to change the display from U.S. to metric measurement units. RESET Button Use this button to reset the following displays to zer o: A verage Fuel Economy T rip Odometer Ela.
Global Reset If the RESET button is pressed twice within 2 seconds while in any of the 3 resettable displays (A VG ECO, ODO, ET), the Global Reset will reset all 3 displays. Step Button Use this button to choose or cycle through the four trip conditions.
When the DTE value is less than 30 miles estimated driving distance, the DTE display will change to an alternating test display of “LO” and “FUEL”.
C/T Button Use this button to select a readout of the outside tem- perature and one of eight compass headings that indicate the direction in which the vehicle is facing. W ARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy , particularly in woods or on bridges.
Manual Compass Calibration NOTE: T o ensure pr oper compass calibration, make sure the compass variance is pr operly set before manu- ally calibrating the compass. If the compass appears erratic and the CAL symbol does not appear , you must manually put the compass into the “Calibration” mode.
NOTE: The default for the compass variance is zone 8. T o set the variance: T urn the ignition ON and set the display to “Compass/T emperature.” Pr ess and hold the RESET button approximately five seconds. The last vari- ance zone number will be displayed.
GARAGE DOOR OPENER The HomeLink 威 Universal T ransceiver replaces up to three r emote controls (hand held transmitters) that oper - ate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button.
W ARNING! A moving garage door can cause injury to people and pets in the path of the door . People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety stan- dards.
W ARNING! V ehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run the vehicle’s exhaust while training the transceiver . Exhaust gas can cause seri- ous injury or death. W ARNING! Y our motorized door or gate will open and close while you are training the Universal T ransceiver .
NOTE: Some gate operators and garage door openers may requir e you to replace this Pr ogramming Step 3 with procedur es noted in the ⬙ Gate Operator/Canadian Pro- gramming ⬙ section. 4. The HomeLink indicator light will flash slowly and then rapidly after HomeLink successfully receives the frequency signal fr om the hand-held transmitter .
and, depending on the brand of the garage door opener (or other rolling code equipped device), r epeat this sequence a third time to complete the pr ogramming. HomeLink should now activate your rolling code equipped device. NOTE: T o program the r emaining two HomeLink but- tons, begin with ⬙ Programming ⬙ step two.
etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there ar e still programming dif ficulties or questions, contact HomeLink at: www .
This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received including interfer ence that may cause undes- ired operation.
W ARNING! • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.
Closing Sunroof - Express Press the switch forwar d and release, and the sunr oof will close automatically from any position. The sunr oof will close fully and stop automatically . This is called Express Close. During Expr ess Close operation, any movement of the switch will stop the sunroof.
Wind Buffeting W ind buffeting can be described as the perception of pressur e on the ears or a helicopter type sound in the ears. Y our vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.
All accessories connected to this outlet should be re- moved or turned OFF when the vehicle is not in use to protect the battery against dischar ge. There is an additional Pop-Up Power Outlet in the center console ahead of the shifter lever . This outlet is powered only when the ignition switch is in the On or Accessories position.
CIGAR LIGHTER AND ASH RECEIVER Cigar Lighter and Ash Receiver (vehicles equipped with a manual transmission) On vehicles equipped with a manual transmission, the ash receiver is opened and closed by pushing on the front surface of the r eceiver and then allowing the receiver to open.
NOTE: As a child safety precaution, the lighter only operates with the ignition switch ON. It heats when pushed in and pops out automatically when ready for use.
T o secure the cup, place the cup to be held into one of the cup wells and then push the cupholder arm toward the cup until it is held stable. Cup Holder Door Handle Cup Holders Automatic T ransmissio.
Front Instrument Panel Cupholders (Bucket Seats) — Automatic T ransmission If your new Ram truck is equipped with bucket seats there ar e three cup holders located on the fr ont of the center console. Front Cupholders — Manual T ransmission The cupholders consist of two cupwells for passenger convenience.
STORAGE Center Storage Compartment The center portion of the seat folds down to provide an armrest with unique storage compartments under the lid. Push the button on the front of the armr est to raise the cover .
Center Storage Compartment (Bucket Seats)— If Equipped Push the upper button on the front of the armr est to raise the upper cover . Inside is a power outlet (if equipped), a cut out for a cell phone charger cor d, removable coin holder (if equipped), and a divider to configure the storage area into separate compartments.
CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery , even when not in use (i.e. cellular phones, etc.). Eventually , if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
There is also storage behind the seat. This storage ar ea contains the 10 inch subwoofer . FOLD FLA T LOAD FLOOR — IF EQUIPPED Fold Flat Load Floor — If Equipped Quad Cab models with a 60/40 rear seat, may be equipped with a folding steel load floor under the right rear seat.
W ARNING! Do not operate the vehicle with loose items stored on the load floor . While driving or in an accident you may experience, abrupt stopping, rapid acceleration, or sharp turns. Loose objects stored on the load floor may move around with force and strike occupants, resulting in serious or fatal injury .
3. Reverse the procedure to stor e the load floor . Positioning the Load Floor for Storage Access Under the Seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap. 3. Lift the load floor up to access storage under the load floor .
W ARNING! Do not drive with the load floor in the up position. When stopping fast or in an accident, the load floor could move to the down position causing serious injury . 4. Reverse the procedure to put the load floor back in the secured down position befor e you operate the vehicle.
PICKUP BOX The pickup box on your new Ram has many features designed for utility and convenience. NOTE: If you are installing a toolbox to the fr ont of the pickup box, you must use Mopar 威 toolbox brackets available from your dealer . Y ou can carry wide building materials (sheets of ply- wood, etc.
W ARNING! • Care should always be exercised when operating a vehicle with unrestrained cargo. V ehicle speeds may need to be reduced. Severe turns or rough roads may cause shifting or bouncing of the cargo that may result in vehicle damage. If wide building materials are to be frequently carried, the installation of a support is recommended.
Raise the right side of the tailgate until the right side pivot clears the hanger bracket. Slide the entire tailgate to the right to free the left side pivot. Remove the tailgate from the vehicle entir ely . Do not carry the tailgate loose in the truck pickup box.
TONNEAU COVER REMOV AL — IF EQUIPPED NOTE: This procedur e requir es a minimum of two (2) people to complete. 1. Lower the tailgate. 2. Pull the handle, located at the center rear of the underside of the cover , to release the latches and lift the cover to the up position.
3. Remove the right and left attach bolts from front hinges. Pulling The Latch Release Handle Left Hinge And Attach Bolt UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 153 3.
4. Move the two, already in open position, latches at rear corner of the cover into the closed position. 5. While supporting the cover , release both gas prop r ods using the quick disconnects Placing.
6. Swing the gas prop rods into the storage clips, on the cover . 7. Lower the rear of cover with the latches in the closed position onto strikers to create space for hands to lift cover .
8. Lift the cover straight up and the carry cover towards the rear of the vehicle Reverse the procedur e for installation. NOTE: Insert the locator pins on the front hinges into the front locator pin holes, on the top edge of the bed.
MIRRORS Automatic Dimming Mirror— If Equipped This mirror automatically adjusts for annoying headlight glare fr om vehicles behind you. Y ou can turn the feature on or off by pr essing the button at the base of the mirror . A light in the button will indicate when the dimming feature is activated.
W ARNING! V ehicles and other objects seen in a right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side convex mirror could cause you to collide with an- other vehicle or other object.
Set the top switch to the left or right for the left or right mirror , and set it to the center off position to pr event accidentally moving a mirror when you ar e finished adjusting the mirror . T o adjust a mirror , select left or right with the top switch, and press one of the four arr ows for the direction you want the mirr or to move.
.
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instruments And Contr ols ................. 1 6 3 䡵 Instrument Cluster ...................... 1 6 4 䡵 Instrument Cluster Description ............. 1 6 5 䡵 Electronic Digital Clock ..............
▫ Operation Instructions - (CD Mode For MP3 Audio Play) .......... 1 8 5 ▫ Load/Eject Button (CD Mode For MP3 Play) . . 185 䡵 V ideo Entertainment System (Sales Code XR V) — If Equipped ........................... 1 8 7 䡵 Remote Sound System Controls .
INSTRUMENTS AND CONTROLS UNDERST ANDING YOUR INSTRUMENT P ANEL 163 4.
INSTRUMENT CLUSTER 164 UNDERST ANDING YOUR INSTRUMENT P ANEL.
INSTRUMENT CLUSTER DESCRIPTION 1. Check Gages This light illuminates when the V oltmeter , Engine Oil Pressur e or Engine Coolant T emperature gages indicate a reading either too high or too low . Examine the gages carefully , and follow the instructions above for each indicated problem.
CAUTION! Do not operate the engine with the tachometer pointer at high rpm for extended periods. Engine damage may occur . 5. Airbag Indicator Light The indicator lights and remains lit for 6 to 8 seconds when the ignition is first turned on.
NOTE: If the gauge pointer moves to either extreme of the gauge, the “Check Gages” indicator will illuminate and a single chime will sound. 10. TOW HAUL The TOW HAUL button is located at the end of the gear shift lever . This light will illuminate when the TOW HAUL button is pushed once.
12. Security The light will flash rapidly for approximately 16 seconds when the vehicle theft alarm is arming. The light will flash at a slower rate after the alarm is set. The security light will also come on for about two seconds when the ignition is first turned ON.
15. Check Gages Light This light is part of an onboard diagnostic system which monitors the emissions and engine control system. If the vehicle is ready for emissions testing the light will come on when the ignition is first turned on and remain on, as a bulb check, until the engine is started.
If the light remains on when the parking brake is released, it indicates a possible brake hydraulic system malfunction. In this case, the light will remain on until the cause is corrected. If brake failure is indicated, immediate r epair is necessary and continued operation of the vehicle in this condition is dangerous.
as 4-wheel-drive operation (e.g. off- r oad operation). If this light comes on, stop the vehicle and run the engine at idle or faster , with the transmission in NEUTRAL until the light goes off. 21. Low W asher Fluid Light This light comes on when the washer fluid level falls below approximately 1/4 full.
25. Door Ajar The Door Ajar light will illuminate when any door is opened. When the ignition is ON the Door Ajar light will stay illuminated until the open door is closed. When the ignition is OFF the Door Ajar light will stay illuminated until the open door is closed or the battery saver feature automatically turns the light of f.
Clock Setting Procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side T une / Audio control. 3. After the hours are adjusted, press the right side T une / Audio control to set the minutes. 4. Adjust the minutes using the right side T une / Audio control.
Satellite Navigation Radio with CD Player with MP3 Capability (REC) - combines a Global-Positioning System-based navigation system with an integrated color screen to pr ovide maps, turn identification.
Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/V olume Control (Rotary) Press the ON/VOL contr ol to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio.
NOTE: In Hands Free Phone (if equipped) mode, the MUTE button mutes the microphone. SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to sear ch for the next listenable station, in either AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next.
TUNE Control (Radio Mode) T urn the right side rotary contr ol clockwise to increase or counter-clockwise to decr ease the frequency . AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the T one, Balance, and Fade Press the r otary TUNE control and BASS will display .
T oggle the PTY button to select the following format types: Program T ype 16 Digit-Character Dis- play No program type or un- defined None Adult Hits Adult_Hits Alert Alert Alert Alert Classical Clas.
By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. If a preset button is activated while in the PTY (Program T ype) mode, the PTY mode will be exited and the radio will tune to the preset station.
Operation Instructions - (CD MODE for CD Audio Play) NOTE: The ignition switch must be in the ON or ACC position to operate the radio. NOTE: Note: This Radio is capable of playing compact discs (CD), .
MUTE Button (CD MODE for CD Audio Play) Press the MUTE button to cancel the sound fr om the speakers. ⬙ MUTE ⬙ will be displayed. Press the MUTE button a second time and the sound from the speakers will return. Rotating the volume contr ol, turning the radio ON/OFF , or turning OFF the ignition will also return the sound fr om the speakers.
If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded. If the CD is not r emoved, the radio will continue to play the non-removed CD. If the CD is removed and ther e are other CD’s in the radio, the radio will play the next CD after a 2 minute timeout.
Press the SEEK button to move to the next randomly selected track. Press and hold the FF button to fast forwar d through the tracks. Release the FF button to stop the fast forward feature. Press the RND button a second time to stop Random Play . B u t t o n s1-6( C D MODE for CD Audio Play) Selects disc position s1-6f o r Play/Load/Eject.
Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files). Discs created with an option such as ⬙ keep disc open after writing ⬙ are most likely multisession discs.
Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
LOAD / EJECT - Eject Press the LOAD/ EJECT button and the push- button with the corresponding number wher e the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show ⬙ EJECTING DISC ⬙ when the disc is being ejected and prompt the user to r emove the disc.
AM/FM Button (CD Mode for MP3 Play) Switches back to Radio mode. RND/ PTY Button (CD Mode for MP3 Play) Pressing this button plays files randomly . SET/DIR Button (CD Mode for MP3 Play) Press the SET/DIR Button to display folders, when playing an MP3 discs that have a file/folder structur e.
REMOTE SOUND SYSTEM CONTROLS The remote sound system contr ols are located on the r ear surface of the steering wheel. Reach behind the wheel to access the switches.
CD Player Pressing the top of the switch once will go to the next track on the CD. Pressing the bottom of the switch once will go to the beginning of the current track or to the beginning of the previous track if it is within one second after the current track begins to play .
RADIO OPERA TION AND CELLULAR PHONES Under certain conditions, the operation of a cellular phone in your vehicle can cause erratic or noisy perfor- mance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna.
Air Conditioning and Heating Operation T o turn on the Air Conditioning, set the fan control at any speed and press the snowflake button located on the control panel. Conditioned air will be dir ected through the outlets selected by the mode control. A light in the snowflake button shows that the air conditioning is on.
Recirculation Pushbutton Pushing the Recirculation button al- lows interior air to recir culate continu- ously in any position except defrost and defrost/floor mode for rapid cool down of the interior . See “Fast Cooldown” later in this section. Mode Control The mode control allows you to choose from several patterns of air distribution.
Heat Outside air flows primarily through the floor out- lets located under the instrument panel. Mix Outside air flows in equal proportions thr ough the floor and defroster outlets. Defrost Outside air is primarily directed to the windshield through the defr oster outlets located at the base of the windshield and side window demist outlets.
Dual Zone T emperature Control Use this control to r egulate the temperature of the air inside the passenger compartment. This is accomplished by having separate temperature contr ol slides for both the driver and front passenger . The blue area of the scale indicates cooler temperatures while the r ed area indicates warmer temperatures.
pushbutton. When a comfortable condition has been reached, choose a mode position and adjust the tempera- ture contr ol slide and blower speed as necessary to maintain comfort. For high humidity conditions it may be necessary to remain in the Recir culation mode to maintain comfort.
When using the air conditioner in extremely heavy traf fic in hot weather especially when towing a trailer , addi- tional engine cooling may be requir ed. If this situation is encountered, operate the transmission in a lower gear to increase engine RPM, coolant flow and fan speed.
Operating Tips Chart UNDERST ANDING YOUR INSTRUMENT P ANEL 197 4.
.
ST ARTING AND OPERA TING CONTENTS 䡵 Ignition/Starter Switch ................... 2 0 2 ▫ Lock .............................. 2 0 2 ▫ O f f ............................... 2 0 2 ▫ O n................................ 2 0 2 ▫ A C C .............
▫ Four-Wheel Anti-Lock Brake System (ABS) . . . 216 䡵 Power Steering ........................ 2 1 8 䡵 T ire Safety Information ................... 2 1 8 ▫ T ire Markings ........................ 2 1 8 ▫ T ire Identification Number (TIN) ....
▫ Materials Added T o Fuel ................ 2 4 1 ▫ Fuel System Cautions .................. 2 4 1 ▫ Carbon Monoxide W arnings .............. 2 4 2 䡵 Adding Fuel .......................... 2 4 3 ▫ Fuel Filler Cap (Gas Cap) ............... 2 4 3 䡵 Catalytic Converter .
IGNITION/ST ARTER SWITCH LOCK Engages the steering wheel lock (if equipped) when the steering wheel is turned. OFF Unlocks the steering wheel (if equipped with locking wheel). ON This is the normal running position. ACC Allows the electrical accessories to be used when the engine is not running.
ST ARTING PROCEDURES The starter should not be operated for more than 15- second intervals. W aiting a few seconds between such intervals will protect the starter fr om overheating. Manual T ransmission Apply the parking brake, place the gearshift control lever in NEUTRAL and depress the clutch pedal to the floor before starting the vehicle.
instrument panel and r elease when the engine starts. If the engine fails to start within 10 seconds, turn the key to the OFF position, wait 5 seconds, then repeat the normal starting procedur e. If Engine Fails T o Start If the engine fails to start after you have followed the normal starting procedur e, it may be flooded.
After Starting The idle speed is automatically controlled and will de- crease as the engine warms up. CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust tempera- tures which can damage your vehicle. Do not leave your vehicle unattended with the engine running.
“P” Park This gear position supplements the parking brake by locking the transmission. The engine can be started in this range. Never use Park while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply parking brake first, then place the selector in Park position.
W ARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in re- verse. Y ou could lose control of the vehicle and hit someone or something.
NOTE: Do not exceed maximum engine speed. “1” First Use this position for driving up very steep hills and for engine braking at low speeds (20 mph [32 km/h] or less) when going downhill.
• the engine coolant has reached normal operating tem- perature; • vehicle speed is above approximately 30 mph (48 km/h); • the “TOW/HAUL” switch has not been activated; • transmission has reached normal operating tempera- ture.
occurs, press the “T OW/HAUL” button. This will im- prove performance and r educe the potential for transmis- sion overheating or failur e due to excessive shifting. The “TOW/HAUL” light will illuminate in the instr u- ment cluster to indicate when the switch has been activated.
Manual T ransmission — 6-Speed NOTE: The parking brake should be engaged before leaving the vehicle, especially on an incline. This model is equipped with a clutch interlocking igni- tion system. The clutch pedal must be fully depressed to start the vehicle.
Y ou should use low gear when starting from a standing position if under a heavy load. T o shift into Reverse, come to a complete stop. Depress the clutch and pause briefly to allow the gear train to stop. Move the shift lever from the Neutral position straight across and up into Reverse.
CAUTION! When descending a hill, be very careful to downshift one gear at a time to prevent overspeeding the engine which can cause valve damage. LIMITED-SLIP DIFFERENTIAL The limited-slip differ enti.
P ARKING BRAKE The foot operated parking brake is positioned below the lower left corner of the instrument panel. T o release the parking brake, pull the parking brake release handle. NOTE: The instrument cluster r ed brake warning light will come on and flash to indicate that the parking brake is applied.
W ARNING! • Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage or injury . Also be certain to leave a manual transmis- sion in Reverse or first gear . Failure to do so may allow the vehicle to roll and cause damage or injury .
Brake Noise During normal operation of the brake system certain noises may be present fr om time to time. Occasional ⬙ groan ⬙ or ⬙ squeal ⬙ noises may occur during normal operation of the brake system which may not be indica- tive of a problem.
W ARNING! Pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer . Just press firmly on your brake pedal when you need to slow down or stop.
POWER STEERING Y our power steering system will provide mechanical steering capability if power assist is lost. If for any reason the hydraulic pr essure is interrupted, it will still be possible to steer your vehicle. Under these conditions you will experience a substantial increase in steering effort.
• European Metric tir e sizing is based on European design standards. T ires designed to this standar d have the tire size molded into the sidewall beginning with the section width. The letter ⬙ P ⬙ is absent from this tir e size designation. Example: 215/65R15 96H • L T(Light T ruck)-Metric tire sizing is based on U.
T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standar ds ⴖ ....blank.... ⴖ = Passenger car tire based on Eur opean design standards LT = Light T ruck tire based on U.
EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry . H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Tire Loading and T ire Pressure T ire Placard Location NOTE: The proper cold tir e inflation pressur e is listed on either the face of the driver’s door or the driver’s side “B” pillar .
3) the tire size designed for your vehicle 4) the cold tire inflation pr essures for the fr ont, rear and spare tir es. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.
4. The resulting figure equals the available amount of cargo and luggage load capacity . For example, if “XXX” amount equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lb.
226 ST ARTING AND OPERA TING.
W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
2. Economy— Improper inflation pr essures can cause uneven wear patterns to develop across the tir e tread. These abnormal wear patterns will reduce tr ead life resulting in a need for earlier tire r eplacement. Underinflation also increases tir e rolling r esistance and results in higher fuel consumption.
CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressur es specified on the placard ar e always “cold tire inflation pr essure”.
T ire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tir e inflation pressur e is very important.
Compact Spare Tire — If Equipped The compact spare is for temporary emer gency use with radial tires. It is engineer ed to be used on your style vehicle only . Since this tire has limited tread life, the original tire should be r epaired (or r eplaced) and rein- stalled at the first opportunity .
Limited Use Spare — If Equipped The limited use spare tir e is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tir e warning label located on the limited use spare tire and wheel assembly . This tire may look like the original equipped tire on the fr ont or rear axle of your vehicle, but it is not.
W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck.
Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • T ire pressur e • Distance driven W ARNING! T ires and spare tire should be replaced after six years, regardless of the remaining tread.
W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combina- tions of unapproved tires and wheels may change suspension dimensions and performance charac- teristics, resulting in changes to steering, han- dling, and braking of your vehicle.
Improper alignment will not cause vehicle vibration. V ibration may be a result of tire and wheel out-of- balance. Proper balancing will r educe vibration and avoid tire cupping and spotty wear .
These cautions apply to all chain traction devices, includ- ing link and cable (radial) chains. T ire chain use is permitted only on the rear tir es of SR T–10 Models. NOTE: The use of class “S” chains is permitted on SR T– 10 Models with the use of 17 x 8 steel wheels (part number 521 13265AC) available from your authorized dealer .
TIRE ROT A TION RECOMMENDA TIONS T ires on the front and r ear axles of vehicles operate at differ ent loads and perform differ ent steering, driving, and braking functions. For these reasons, they wear at unequal rates, and develop irregular wear patterns.
FUEL REQUIREMENTS Y our vehicle is designed to meet all emis- sion regulations and pr ovide excellent fuel economy when using high quality pre- mium unleaded gasoline having an octane rating of 91 or higher . Light spark knock at low engine speeds is not harmful to your engine.
Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with mate- rials called oxygenates such as 10% alcohol, MTBE, ETBE or T AME. Oxygenates are r equired in some ar eas of the country during the winter months to reduce carbon monoxide emissions.
Sulfur In Gasoline Y our vehicle may have been designed to meet California low emission standards on clean burning, low sulfur , California gasoline. Gasoline sold outside of California is allowed to have higher sulfur levels that may affect the performance of your vehicle’s catalytic converter .
some light smoke, your engine may be out of tune or malfunctioning and may requir e immediate service. Contact your dealer for service assistance. • When pulling a heavy load or driving a fully loaded vehicle when the humidity is low and the temperature is high, use a premium unleaded fuel to help pr event spark knock.
the vehicle is raised. Have any abnormal conditions repair ed promptly . Until repaired, drive with all side windows fully open. ADDING FUEL NOTE: The fuel tank filler tube is about 2 inches (50 mm) down from the opening.
CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. W ARNING! • Never allow any lit smoking materials near the vehicles while removing the cap or filling the tank.
CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly .
VEHICLE LOADING Certification Label As requir ed by National Highway T raffic Safety Admin- istration Regulations, your vehicle has a certification label affixed to the driver’s side door or pillar .
T ire Size The tire size on the Label r epresents the actual tir e size on your vehicle. Replacement tires must be equal to the load capacity of this tire size.
Improper weight distributions can have an adverse ef fect on the way your vehicle steers and handles and the way the brakes operate. CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GA WR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles.
Gross V ehicle W eight Rating (GVWR) 6500 LBS. TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer car efully re- view this information to tow your load as efficiently and safely as possible.
Gross T railer W eight (GTW) The gross trailer weight (GTW) is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its ⬙ loaded and ready for operation ⬙ condition.
Frontal Area The maximum height and maximum width of the front of a trailer . T railer Sway Control The trailer sway control is a telescoping link that can be installed between the hitch receiver and .
T railer Hitch Classification The rear bumper is intended to tow trailers up to 2,000 lbs (907 kg) without added equipment or alterations to the standard equipment. Y our vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional T railer T ow Prep Package.
T railer T owing Weights (Maximum T railer Weight Ratings) NOTE: For additional trailer towing information (maxi- mum trailer weight ratings) refer to the following website addresses: • http:// www .dodge.com/towing . • http:// www .dodge.ca (Canada).
• The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle.
W ARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.
• T otal weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. GVWR 2. GTW 3. GA WR 4.
T owing Requirements — T railer Brakes − Do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer . This could cause inadequate braking and possible personal injury . − An electronically actuated trailer brake contr oller is requir ed when towing a trailer with electronically actuated brakes.
W ARNING! Do not connect trailer brakes to your vehicle’s hy- draulic brake lines. It can overload your brake sys- tem and cause it to fail. Y ou might not have brakes when you need them and could have an accident. T owing any trailer will increase your stopping dis- tance.
T owing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away fr om heavy traffic. If using a manual transmission vehicle for trailer towing, all starts must be in FIRST gear to avoid excessive clutch slippage.
NOTE: Check the automatic transmission fluid level before towing. T owing T ips — T ow/Haul (If Equipped) T o reduce potential for automatic transmission over heat- ing, turn the “TOW HAUL” featur e ON when driving in hilly areas or shift the transmission to Drive position 2 on more sever e grades.
T railer T owing Mirrors — If Equipped These mirrors ar e designed with an adjustable mirror head to provide a gr eater vision range when towing extra-wide loads. T o change position inboard or out- board, the mirr or head should be rotated (flipped Out or In).
SNOWPLOW Dodge SRT -10 Models NOTE: DO NOT use Dodge SR T - 10 Models for snowplow applications. W ARNING! Snowplows, winches, and other aftermarket equip- ment should not be added to the front end or your vehicle. The airbag crash sensors may be affected by the change in the front end structure.
CAUTION! Using this vehicle for snowplow applications can cause damage to the vehicle. W ARNING! Attaching a snowplow to this vehicle could ad- versely affect performance of the airbag system in an accident.
EQUIPMENT IDENTIFICA TION PLA TE The equipment Identification Plate is located on the hood inner surface. The following information about your vehicle is dis- played on this plate: Model, Wheelbase, V.
WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Lights .................. 2 6 6 䡵 Adding Fuel .......................... 2 6 7 䡵 Jack Location .......................... 2 6 8 ▫ Removal ........................... 2 6 8 ▫ Reinstalling The Scissors-T ype Jack And T ools (Srt–10 Models) .
HAZARD W ARNING LIGHTS The Hazard W arning switch is mounted on the top of the steering column as shown in the illustration. T o engage the Hazard W arning lights, depress the button on the top of the steering column.
ADDING FUEL The fuel tank filler tube has a restriction about 2 inches (50 mm) inside the opening. If using a portable fuel container , it should have a flexible nozzle long enough to reach past the r estriction. W ARNING! A fire may result if gasoline is pumped into a portable container that is in a vehicle or on a truck bed.
JACK LOCA TION Removal The jack and jack tools are stor ed under the front passenger seat. Lift the tab and slide the plactic cover forward for access.
W ARNING! The jack is designed to use as a tool for changing tires only . The jack should not be used to lift the vehicle for service purposes, unless suitable sup- ports are placed under the vehicle as a safety mea- sure. The vehicle should be jacked on a firm level surface only .
Reinstalling The Scissors-T ype Jack And T ools (SRT–10 Models) 1. Lower the jack all the way down by turning the jack turn-screw until the jack is snug. 2. Position the jack and tool bag (unrolled). Make sure the lug wrench is under the jack near the jack turn-scr ew .
3. Fold the flap and roll the jack tool kit into a cylindrical package (in direction of arr ows), and tie to the jack using the tie straps. Folding Flap and Rolling Bag T ying Bag to Jack with Straps .
4. Place the jack and tools in the storage position holding the jack by the jack turn-screw , slip the jack and tools under seat so that the bottom slot engages into the fastener on the floor and then secure to the floor pan using the wing bolt.
CHANGING A FLA T TIRE Removing The Spare Tire Remove the spare tir e before attempting to jack the truck. Attach the wheel wrench to the jack extension tube. Insert the tube through the access hole between the lower tailgate and the top of the bumper and into the winch mechanism tube.
Tire Changing Procedure W ARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. Y ou could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
• T urn on the Hazard W arning Flasher . • Block both the front and r ear of the wheel diagonally oppo- site the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. • Passengers should not remain in the vehicle when the vehicle is being jacked.
1. Remove the spare wheel, jack, and tools from storage. 2. Using the wheel wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground.
• When changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle between the spring and the shock absorber with the drive tubes extending to the rear . • Connect the jack tube extension and wheel wrench.
6. Using the wheel wrench, finish tightening the nuts using a crisscross pattern. Corr ect nut tightness is 90–1 10 ft. lbs. (125–150 N·m). If in doubt about the correct tightness, have them checked with a torque wr ench by your dealer or at a service station.
Disc Wheels T ype Nut Stud Size T orque Ft. Lbs. T orque Newton Meters Cone 1/2-20 90-1 10 125-150 T o Stow The Flat Or Spare T urn the wheel so that the valve stem is down. Slide the wheel retainer thr ough the center of the wheel and position it properly acr oss the wheel opening.
JUMP-ST ARTING Y ou should not try to start your vehicle by pushing or towing. V ehicles equipped with an automatic transmis- sion cannot be started this way and pushing or towing a vehicle equipped with a manual transmission may over- heat and damage the catalytic converter .
2. Park the booster vehicle within cable reach but with- out letting the vehicles touch. Set the parking brake on both vehicles, place the automatic transmission in Park or the manual transmission in Neutral, and turn the ignition OFF . 3. T urn off the heater , radio, and all unnecessary electri- cal loads.
5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery . Make sure you have a good contact on the engine. W ARNING! • Do not connect the cable to the negative post of the discharge battery .
FREEING A STUCK VEHICLE If vehicle becomes stuck in snow , sand, or mud, it can often be moved by a rocking motion. Move the gear selector rhythmically between FIRST and REVERSE, while applying slight pressur e to the accelerator .
.
MAINT AINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment— 8.3L ............... 2 8 8 䡵 Onboard Diagnostic System (OBD II) ......... 2 8 9 䡵 Emissions Inspection And Maintenance Programs ............................ 2 8 9 䡵 Dealer Service ....
▫ Front Suspension Ball Joints .............. 3 0 2 ▫ Steering Linkage — Inspection ............ 3 0 3 ▫ Body Lubrication ..................... 3 0 3 ▫ W indshield W iper Blades ................ 3 0 4 ▫ W indshield W ashers ...............
▫ Center High-Mounted Stoplight W ith Cargo Light ......................... 3 3 1 ▫ Cab T op Clearance Lights — If Equipped .... 3 3 2 ▫ T ailgate ID Lights (Dual Rear Wheels) ....... 3 3 4 ▫ Side Marker Lights (Dual Rear Wheels) ...... 3 3 5 ▫ Fog Lights .
ENGINE COMP ARTMENT— 8.3L 288 MAINT AINING YOUR VEHICLE.
ONBOARD DIAGNOSTIC SYSTEM (OBD II) Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions and engine control systems.
For states which have an I/M (Inspection and Maintenance) requir ement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is r eady for testing.
b. The MIL light will r emain fully illuminated until the first engine crank or the key is turned off. This means that your vehicle’s OBD system is ready and you can proceed to the I/M station. If your OBD system is not ready , you should see your dealer or repair facility .
W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level r eadings. Maintain the oil level between the ADD and SAFE markings on the dipstick. Adding one quart of oil when the reading is at the ADD mark will result in a SAFE r eading on these engines.
• More than 50% of your driving is at sustained high speeds during hot weather , above 32°C (90°F) • T axi, Police or delivery service (commercial service) • Off-r oad or desert operation • If equipped for and operating with E-85 (ethanol) fuel.
Engine Oil Identification (API) Symbol There is a symbol to aid you in selecting the pr oper engine oil. This symbol means that the oil has been certified by the American Petroleum Institute (API). W e only recommend synthetic API Certified engine oils, such as Mo- bil 1 威 , that meet the requir ements of Material Standard MS-10725.
Materials Added to Engine Oil Do not add any materials (other than leak detection dyes) to engine oil. Engine oil is an engineered pr oduct and it’s performance may be impaired by supplemental addi- tives. Disposing of Used Engine Oil And Oil Filters Care should be taken in disposing of used engine oil and oil filters from your vehicle.
Spark Plugs Spark plugs must fire pr operly to assure engine perfor - mance and emission control. New plugs should be in- stalled at the specified mileage. The entire set should be replaced if ther e is any malfunction due to a faulty spark plug, malfunctioning spark plugs can damage the cata- lytic converter .
Catalytic Converter The catalytic converter requir es the use of unleaded fuel only . Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic con- verter will not requir e maintenance.
W ARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system. Do not park or operate your vehicle in areas where your exhaust system can contact any- thing that can burn.
Crankcase Emission Control System Proper operation of this system depends on fr eedom from plugging due to deposits. As vehicle mileage builds up, the Crankcase V entilation V alve orifice may accumu- late deposits. If a valve is not working properly , replace it with a new orifice.
CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and identified on the battery case.
Refrigerant Recovery And Recycling The air conditioning system of your vehicle contains R-134a, a refrigerant that does not deplete the ozone layer in the upper atmosphere. The manufactur er recommends that air conditioning service be done by facilities using refrigerant r ecycling and recovery equipment that meets SAE standard J1991.
The ball joints originally supplied with the vehicle are permanently lubricated at the factory and do not requir e service. However , if the seals on the ball joints are damaged, the joints should be replaced. Serviceable replacement ball joints ar e available.
Windshield Wiper Blades The rubber edges of the wiper blades and the windshield should be cleaned periodically with a sponge or soft cloth and a mild nonabrasive cleaner . This will remove accu- mulations of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades.
Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Whenever a change is noticed in the sound of the exhaust system, .
Cooling System Cooling System Maintenance At the intervals shown in the Maintenance Schedules Section of the manual, the system should be drained, flushed and filled. Inspection Check engine coolant (antifreeze) pr otection every 12 months (before the onset of fr eezing weather , where applicable).
W ARNING! Never add coolant to the radiator when the engine is overheated. Do not loosen or remove pressure cap to cool an overheated engine! The coolant is under pressure and severe scalding could result. Drain, Flush And Refill At intervals shown on the Maintenance Schedules, the system should be drained, flushed and refilled.
NOTE: Failure to follow the antifr eeze concentration and replacement r ecommendations, or failure to use antifreeze formulated to pr event corrosion of all cooling system metals, may result in radiator plugging, over heat- ing, or cooling system leaks such as in core hole plugs.
Disposal Of Used Engine Coolant Used ethylene glycol based engine coolant is a regulated substance requiring pr oper disposal. Check with your local authorities to determine the disposal rules for your community . Do not store ethylene glycol-based engine coolant in open containers or allow it to remain in puddles on the ground.
Insure nylon tubing in these ar eas has not melted or collapsed. Inspect all hose connections such as clamps and cou- plings to make sure they ar e secure and no leaks ar e present. Components should be replaced immediately if ther e is any evidence of wear or damage that could cause failure.
W ARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. Use only brake fluid that has been in a tightly closed container to avoid contamination from for eign matter or moisture.
Propeller Shaft Universal Joints Cross T ype (No fittings) — Relubrication of this type of universal joint is not requir ed. The seals should be inspected for external leaks or damage. If external leaks or damage is evident, the universal joint should be replaced.
Manual T ransmission Lubricant Selection Refer to the Fluids, Lubricants and Genuine Parts section for correct fluid type. CAUTION! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality .
Procedure For Checking Fluid Level T o properly check the automatic transmission fluid level, the following procedur e must be used: 1. The vehicle must be on level ground. 2. The engine should be running at curb idle speed for a minimum of 60 seconds.
CAUTION! Using a transmission fluid other than the manufac- turers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder . Using a transmission fluid other than the manufacturers recommended fluid will result in more frequent fluid and filter changes.
Front Wheel Bearings Front wheel bearings for all Dodge Ram T rucks ar e sealed-for-life. They do not r equire gr easing or seal replacement. In some instances, these bearings will “purge” excess gr ease and the bearing will look slightly wet. This is normal.
Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion V ehicle body care requir ements vary according to geo- graphic locations and usage.
• A void using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder , which will scratch metal and painted surfaces.
• If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials ar e well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use Mopar 威 touch up paint on scratches as soon as possible.
Glass Surfaces All glass surfaces should be cleaned on a regular basis with any commercial household-type glass cleaner . Never use an abrasive type cleaner . Use caution when cleaning inside rear windows equipped with electric defrosters or windshields equipped with a windshield wiper de-icer .
INTEGRA TED POWER MODULE Y our vehicle is equipped with a fuse and relay center located in the engine compartment near the battery . Located on the underside of the cover is a label that identifies each component.
Cavity Cartridge Fuse Mini Fuse Description 9 30 Amp Pink Off Road Module Power 10 5 Amp Orange T rx-Off Rd Pkg Sen (Gas Engine Only) 1 1 10 Amp Red IOD-CNN/Radio/ Under Hood Lamp/ WCM/SDARS/HFM 12 30.
Cavity Cartridge Fuse Mini Fuse Description 24 20 Amp Blue Subwoofer Amplifier 25 10 Amp Red Power Mirror 26 20 Amp Y ellow Brake Switch/ CHMSL/Stop Lamp 27 40 Amp Green Power Seats 28 10 Amp Red Powe.
Cavity Cartridge Fuse Mini Fuse Description 39 10 Amp Red Sunroof/Seatbelt T en- sioner 40 20 Amp Y ellow Cigar Lighter 41 25 Amp Natural Spare 42 30 Amp Pink Diesel PCM (Diesel Only) 1. Disconnect the battery negative (-) cable before remov- ing the cover .
REPLACEMENT LIGHT BULBS LIGHT BULBS — Inside Bulb No. Overhead Console Lights ............... T S 212-2 Dome Light ............................ 7679 All of the inside bulbs are brass or glass wedge base. Aluminum base bulbs are not appr oved. LIGHT BULBS — Outside Bulb No.
1. Open the hood 2. Remove the two (2) bolts from the front of the head- light housing. 3. Remove the plug from the inner fender well and remove the nut thr ough the access hole.
4. Pull the housing out from the fender to allow room to disconnect the electrical connectors. NOTE: For easier removal, pull the headlight assembly straight forward, applying the gr eatest amount of force to the outer edge of the headlight assembly .
5. Unlock and pull connector straight from the base of the headlight halogen bulb. 6. T wist connector on turn signal/park light bulb 1 ⁄ 4 turn and remove connector and bulb fr om housing. 7. Remove housing from vehicle with headlight halogen bulb in housing.
T ail, Stop, T urn and Backup Lights 1. Remove the two (2) screws that pass through the bed sheetmetal. 2. Pull the housing straight out from the body , with a quick motion, to separate the housing from the body . If not pulled straight, locators may be damaged.
3. Push the red lock slide in on the connector and remove the housing from the vehicle. 4. Remove the four (4) screws from the bulb strip in the housing. 5. Pull the appropriate bulb straight from the bulb strip. • T op Bulb: Park/T urn/Hazard • Center Bulb: Stop/Park/Sidemarker • Bottom Bulb: Backup Lights 6.
7. While holding the taillight firmly in place, fasten the top screw first. Center High-Mounted Stoplight With Cargo Light 1. Remove the two (2) screws holding the housing/lens to the body as shown. 2. Separate the connector holding the housing and wir- ing harness to the body .
4. Pull desired bulb straight from the socket. • Outside Bulbs: Cargo Lamps • Inside Bulb: Center High Mount Stop Lamp 5. Reverse procedure for installation of bulbs and hous- ing. Cab T op Clearance Lights — If Equipped 1. Remove the two screws from the top of the light.
2. Rotate the socket 1 ⁄ 4 turn and pull it from the light assembly . 3. Pull the bulb straight from it’s socket and r eplace. MAINT AINING YOUR VEHICLE 333 7.
T ailgate ID Lights (Dual Rear Wheels) 1. Remove the two screws and housing and access the bulb sockets from the r ear . 334 MAINT AINING YOUR VEHICLE.
2. T urn socket 1 ⁄ 4 turn counterclockwise to access the bulb. 3. Pull bulb straight out from socket. 4. Reverse procedure for installation of bulbs and hous- ing. Side Marker Lights (Dual Rear Wheels) 1. Push rearward on the side marker light assembly .
5. Reverse procedure for installation of bulbs and hous- ing. Fog Lights 1. Reach under the vehicle, unlock and twist connector counterclockwise 1 ⁄ 4 turn and remove connector and bulb from housing. 2. Pull bulb straight from the connector . 3. Reverse procedure for installation of bulbs and hous- ing.
FLUID CAP ACITIES U.S. Metric Fuel SR T -10 - Standard Cab Models 26 gal. 98L SR T -10 - Quad Cab Models 34 gal. 129L Engine Oil (with filter) 8.3L (SAE 0W -40 MS-10725) 10 qts.
FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar 威 Antifr eeze/Coolant 5 Y ear/102,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology) P/N 05066386AA or equivalent.
Chassis Component Fluids, Lubricants and Genuine Parts. Manual T ransmission Fluid Mopar Synthetic Manual T ransmission Lubricant 75W/85W (Castrol Syn- torq L T 75W/85W) Automatic T ransmission Fluid Mopar 威 A TF+4, Automatic T ransmission Fluid. Clutch Linkage Multipurpose Grease, NLGI Grade 2 E.
.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance ........ 3 4 2 䡵 Maintenance Schedules ................... 3 4 2 ▫ Schedule “B” .
EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type in this section (Section 8) must be done at the times or mileages specified to assure the continued pr oper functioning of the emission control system.
• T axi, police, or delivery service (commercial service). • Off-r oad or desert operation. • If equipped for and operating with E-85 (ethanol) fuel.
At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will impr ove the accu- racy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark.
Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures ar e below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions.
Miles 3,000 6,000 9,000 12,000 15,000 (Kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) Change engine oil and engine oil filter at interval shown or 3 months, whichever comes first. X X XXX Drain and refill automatic transmission fluid. Re- place filter and adjust bands.
Miles 18,000 21,000 24,000 27,000 30,000 (Kilometers) (30 000) (35 000) (40 000) (45 000) (50 000) Change engine oil and engine oil filter at interval shown or 3 months, whichever comes first. X X XXX Drain and refill automatic transmission fluid. Re- place filter and adjust bands.
Miles 33,000 36,000 39,000 42,000 45,000 (Kilometers) (55 000) (60 000) (65 000) (70 000) (75 000) Change engine oil and engine oil filter at interval shown or 3 months, whichever comes first. X X XXX Drain and refill automatic transmission fluid. Re- place filter and adjust bands.
Miles 48,000 51,000 54,000 57,000 60,000 (Kilometers) (80 000) (85 000) (90 000) (95 000) (100 000) Change engine oil and engine oil filter at interval shown or 3 months, whichever comes first. X X XXX Drain and refill automatic transmission fluid. Re- place filter and adjust bands.
Miles 63,000 66,000 69,000 72,000 75,000 (Kilometers) (105 000) (1 10 000) (115 000) (120 000) (125 000) Change engine oil and engine oil filter at interval shown or 3 months, whichever comes first. X X XXX Drain and refill automatic transmission fluid.
Miles 78,000 81,000 84,000 87,000 90,000 (Kilometers) (130 000) (135 000) (140 000) (145 000) (150 000) Change engine oil and engine oil filter at interval shown or 3 months, whichever comes first. X X XXX Drain and refill automatic transmission fluid.
Miles 93,000 96,000 99,000 102,000 (Kilometers) (155 000) (160 000) (165 000) (170 000) Change engine oil and engine oil filter at interval shown or 3 months, whichever comes first. XXX X Rotate tires. X X Check spare tir e for proper pr essure and correct stowage.
Miles 105,000 108,000 1 1 1,000 1 14,000 117,000 120,000 (Kilometers) (175 000) (180 000) (185 000) (190 000) (195 000) (200 000) Change engine oil and engine oil filter at in- terval shown or 3 months, whichever comes first. X X XXXX Drain and refill automatic transmission fluid.
Miles 105,000 108,000 1 1 1,000 1 14,000 117,000 120,000 (Kilometers) (175 000) (180 000) (185 000) (190 000) (195 000) (200 000) Replace ignition cables. X Inspect and replace, if necessary , the PCV valve.** X** Inspect auto tension drive belt and replace if requir ed.
Schedule “A” Miles 6,000 12,000 18,000 24,000 30,000 (Kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) [Months] [6] [12] [18] [24] [30] Change engine oil and engine oil filter . X X X X X Rotate tir es. X X X X X Check spare tir e for proper pr essure and correct stowage.
Miles 36,000 42,000 48,000 54,000 60,000 66,000 (Kilometers) (60 000) (70 000) (80 000) (90 000) (100 000) (1 10 000) [Months] [36] [42] [48] [54] [60] [66] Change engine oil and engine oil filter . X X X X X X Rotate tir es. X X X X X X Check spare tir e for proper pr essure and cor- rect stowage.
Miles 72,000 78,000 84,000 90,000 96,000 100,000 (Kilometers) (120 000) (130 000) (140 000) (150 000) (160 000) (170 000) [Months] [72] [78] [84] [90] [96] Change engine oil and engine oil filter . X X X X X Drain and refill automatic transmission fluid.
Miles 102,000 108,000 1 14,000 120,000 (Kilometers) (180 000) (190 000) (200 000) (210 000) [Months] [102] [108] [1 14] [120] Change engine oil and engine oil filter . X X X X Rotate tir es. X X X X Check spare tir e for proper pr essure and correct stowage.
** This maintenance is recommended by the manufac- turer to the owner , but not requir ed to maintain the emissions warranty . Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re- ceipts. W ARNING! Y ou can be badly injured working on or around a motor vehicle.
.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle .............................. 3 6 2 ▫ Prepar e For The Appointment ............ 3 6 2 ▫ Prepar e A List ........................ 3 6 2 ▫ Be Reasonable W ith Requests .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional charges with the service manager .
technicians, special tools, and the latest information to assure your vehicle is fixed corr ectly and in a timely manner . This is why you should always talk to your dealer’s service manager first.
Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its Customer Center .
W ARRANTY INFORMA TION (U.S. V ehicles Only) See the W arranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOP AR 姞 P ARTS Mopar 威 fluids, lubricants, parts, and accessories are available from your dealer .
PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Mas- tercar d, American Express, and Discover or ders are ac- cepted. If you prefer mailing your payment, please call for an order form.
• Owner’s Manuals. These manuals have been prepar ed with the assistance of service and engineering specialists to acquaint you with specific Chrysler group vehicles. Included ar e starting, operating, emergency and maintenance pr o- cedures as well as specifications, capabilities and safety tips.
.
INDEX 10.
Adding Fuel ........................ 243,267 Additives, Fuel ......................... 2 4 1 Air Cleaner , Engine (Engine Air Cleaner Filter) . . . 297 Air Conditioner Maintenance ............... 3 0 1 Air Conditioning Refrigerant ............... 3 0 1 Air Conditioning System .
B-Pillar Location ........................ 2 2 3 Brake Fluid ............................ 3 3 9 Brake System ........................ 215,310 Anti-Lock ........................... 2 1 6 Disc Brakes .......................... 3 1 0 Hoses ..............
Climate Control ......................... 1 9 0 Clock ............................. 172,176 Clutch ................................ 3 1 1 Clutch Linkage Maintenance ................ 3 1 1 Compact Disc Maintenance ................. 1 8 9 Compact Spare T ire .
Door Ajar ............................. 1 7 2 Door Locks ............................. 1 3 Door Opener , Garage ..................... 1 2 7 Drive Belts ............................ 2 9 6 DVD Player (V ideo Entertainment System) ...... 1 8 7 Electric Rear W indow Defrost .
Filters Air Cleaner .......................... 2 9 7 Engine Fuel .......................... 2 9 7 Engine Oil ........................ 296,338 Engine Oil Disposal .................... 2 9 6 Flashers T urn Signal ........................... 1 1 1 Flat T ire Stowage .
T achometer .......................... 1 6 5 V oltmeter ............................ 1 6 5 Gear Ranges ........................... 2 0 5 Glass Cleaning .......................... 3 2 0 Gross Axle W eight Rating .................. 2 5 0 Gross V ehicle W eight Rating .
Intermittent W ipers ...................... 1 1 3 Introduction ............................. 4 Jack Location ........................... 2 6 8 Jack Operation .......................... 2 7 4 Jump Starting .......................... 2 8 0 Key , Replacement .
Intensity Control ....................... 1 0 7 Interior .......................... 107,120 Lights On Reminder .................... 1 1 0 Passing ............................. 1 1 1 Seat Belt Reminder ..................... 1 6 6 Service ..............
T railer T owing ........................ 2 6 1 Modifications/Alterations, V ehicle ............. 6 Mopar Parts ......................... 292,365 Multi-Function Control Lever ............... 1 1 1 Occupant Classification System ............... 4 2 Occupant Restraints .
Pickup Box ............................ 1 4 9 Placard, T ire and Loading Information ......... 2 2 3 Power Distribution Center ..................... 3 2 1 Door Locks ........................... 1 3 Mirrors ............................. 1 5 8 Outlet ..
Safety Information, T ire ................... 2 1 8 Safety T ips ............................. 6 8 Satellite Radio .......................... 1 7 4 Schedule, Maintenance .................... 3 4 2 Seat Belt Maintenance .................... 3 2 0 Seat Belt Reminder .
Snow Plow ............................ 2 6 2 Snow T ires ............................ 2 3 7 Spare T ire .......................... 231,232 Spark Plugs ............................ 2 9 7 Speed Control .......................... 1 1 7 Speedometer ......
Compact Spare ........................ 2 3 1 General Information .................... 2 2 7 High Speed .......................... 2 3 0 Inflation Pressur es ..................... 2 2 8 Jacking ............................. 2 7 4 Load Capacity ........
Fluid ............................... 3 3 9 Maintenance .......................... 3 1 3 Manual .......................... 203,21 1 Shifting .......................... 205,212 T ransmitter , Garage Door Opener ............ 1 2 7 T read W ear Indicators .
Fluid ............................ 1 12,304 W indshield W iper Blades .................. 3 0 4 W indshield W ipers ....................... 1 1 2 W iper Blade Replacement .
Ein wichtiger Punkt beim Kauf des Geräts Dodge 2006 DR Ram SRT-10 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Dodge 2006 DR Ram SRT-10 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Dodge 2006 DR Ram SRT-10 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Dodge 2006 DR Ram SRT-10 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Dodge 2006 DR Ram SRT-10 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Dodge 2006 DR Ram SRT-10 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Dodge 2006 DR Ram SRT-10 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Dodge 2006 DR Ram SRT-10. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Dodge 2006 DR Ram SRT-10 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
