Benutzeranleitung / Produktwartung RAM 50 MAG des Produzenten Dixon
Zur Seite of 52
BLACK BEAR ™ ZTR ® Safety Instructions and Operator’s Manual RAM SERIES ™ ZTR ® RAM 44, BS/968999551 RAM 50, BS/968999552 RAM MAG 44, HON/968999559 RAM MAG 44, KOH/968999560 RAM MAG 50, KAW /9.
2.
3 IMPORTANT - READ CAREFULLY The Dixon® ZTR® mower is both easy and fun to operate. However, any power mower must be operated properly to be safe. It is not a toy or a recreational vehicle. Before you start to use the mower, read this Operator’s Manual carefully.
4.
5 TABLE OF CONTENTS RAM SERIES™ Part Number 539 114246IR GENERAL OPERATION .................................................................. 8-9 SLOPE OPERATION .................................................... 10-11 FIRE HAZARDS ...............
SAFETY 6 Blade Contact Tip Over Run Over Back Over RIDING LAWN MOWERS, IF IMPROPERLY OPERATED, CAN CAUSE SERIOUS INJURY OR DEATH Pictured below are the most common causes of injury to the operator or bystander. Please read and understand this manual to prevent injuries.
SAFETY 7 Safety Alert Symbol DANGER (highlighted in red) indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING (highlighted in orange) indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
WARNING 8 GENERAL OPERATION Read, understand, and follow all instructions in this manual and on the mower before starting. Only allow responsible adults, who are familiar with the instructions, to operate the mower. Clear the area of objects such as rocks, toys, wire, etc.
WARNING 9 WARNING ! Failure to observe the following instructions could result in serious injury or death. Turn off blades when not mowing. Injury could occur from contact with moving parts. Under no circumstances should you place hands or feet under the mower deck or in the chute while blades or impeller are still running.
WARNING 10 WARNING ! Failure to observe the following instructions could result in serious injury or death. SLOPE OPERATION Slopes are a major factor related to loss-of-control and tip-over accidents, which can result in severe injury or death. All slopes require extra caution.
WARNING 11 SLOPE OPERATION (continued) DO NOT Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible. Rapid uphill turns may cause tip-over. Do not mow near drop-offs, ditches, or embankments. Unstable ground may cause loss of control.
WARNING 12 FIRE HAZARDS Use extra care when handling gasoline and other fuels. They are flammable and vapors are explosive. Store all fuel in approved containers specifically designed for that purpose. Allow engine to cool before refueling. Never remove fuel cap or add fuel with engine running.
WARNING 13 FIRE HAZARDS (continued) To prevent fire or explosion, keep sparks and open flames away from battery. Keep electrical connections clean and tight. Inspect them often. Loose connections and corrosion increase fire risk. Before disconnecting the negative ground cable, make sure all switches are off.
WARNING 14 CHILDREN, BYSTANDERS AND PETS Tragic accidents can occur if the operator is not alert to the presence of children, bystanders and pets. Children are attracted to lawn mowers and the mowing activity. NEVER assume children, bystanders and pets will stay where they were last seen.
WARNING 15 SERVICE Never run a mower inside a closed area or without proper ventilation. Keep nuts and bolts tight, especially blade attachment bolts, and keep equipment in good condition. Never tamper with safety devices. Check their proper operation regularly.
16 DIXON ® ZTR ® COMMERCIAL / RESIDENTIAL W ARRANTY POLICY RAM 44, RAM 50, RAM 44 MAG™ & RAM 50 MAG™ DIXON® WARRANTS ITS ZTR® MOWERS AGAINST DEFECTS IN MA TERIAL AND WORKMANSHIP FOR THE PERIODS SET FO RTH BELOW . THE SOLE REMEDY UNDER THIS W ARRANTY IS REPLACEMENT OR REP AIR OF P ARTS INCLUDING LABOR COSTS.
SPECIFICATIONS 17 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Additional information may be provided elsewhere in this manual. RAM SERIES™ 44 Model 968999551 1½" square tube side frame Made of 11 gauge fabricated welded construction with external reinforcement ribs.
SPECIFICATIONS 18 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Additional information may be provided elsewhere in this manual. RAM SERIES™ 50 Model 968999552 1½" square tube side frame Made of 11 gauge fabricated welded construction with external reinforcement ribs.
SPECIFICATIONS 19 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Additional information may be provided elsewhere in this manual. RAM MAG SERIES™ 44 Model 968999559 1½" square tube side frame Made of 11 gauge fabricated welded construction with external reinforcement ribs.
SPECIFICATIONS 20 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Additional information may be provided elsewhere in this manual. RAM MAG SERIES™ 44 Model 968999560 1½" square tube side frame Made of 11 gauge fabricated welded construction with external reinforcement ribs.
SPECIFICATIONS 21 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Additional information may be provided elsewhere in this manual. RAM MAG SERIES™ 50 Model 968999561 1½" square tube side frame Made of 11 gauge fabricated welded construction with external reinforcement ribs.
SPECIFICATIONS 22 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Additional information may be provided elsewhere in this manual. RAM MAG SERIES™ 50 Model 968999562 1½" square tube side frame Made of 11 gauge fabricated welded construction with external reinforcement ribs.
SPECIFICATIONS 23 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Additional information may be provided elsewhere in this manual. RAM MAG SERIES™ 50 Model 968999563 1½" square tube side frame Made of 11 gauge fabricated welded construction with external reinforcement ribs.
24 SEAT ADJUSTMENT INSTRUCTIONS 1. Grasp seat slide adjuster and move it into adjustment position. 2. Slide seat forward or backward. 3. Release seat slide adjuster.
CONTROLS 25 CONTROL LEVERS For access to the seat, move control levers to neutral position and swing them outward. TO GO FORWARD • From neutral position, gently push control levers forward. • To increase speed, move levers further forward. TO GO BACKWARDS • From neutral position, gently pull control levers toward you.
CONTROLS 26 — Fig. 3 — PARK BRAKE The park brake is designed to hold the mower from moving and is not intended for use in stopping the mower while it is in motion. The engine will stop if the park brake is engaged while the control levers are in the drive position.
CONTROLS 27 BLADE DRIVE • Located on the control panel, on operator’s right. • To engage the mower blade, pull up on the switch. • To disengage mower blade, push down. CHOKE AND THROTTLE CONTROL LEVER • Located on control panel to operator’s right.
OPERATION INSTRUCTIONS 28 MOWER DECK CUT HEIGHT LIFT LEVER • Use right foot to operate deck foot pedal at right front foot area. • To raise mower deck, push forward with right foot on top portion of foot pedal.
OPERATION INSTRUCTIONS 29 The safe and successful operation of the RAM will depend on the operator having the correct knowledge of all controls used on the mower and making good judgements about the terrain to be mowed. NEVER allow anyone without complete knowledge of all controls and their functions to operate the mower.
OPERATION INSTRUCTIONS 30 STARTING INSTRUCTIONS 1. Park brake must be on, control levers in outward position and blade drive disengaged. 2. Position throttle to desired speed setting.
OPERATION INSTRUCTIONS 31 TESTING OF SAFETY INTERLOCK SYSTEMS The following tests should be performed at the start of each mowing day. PARK BRAKE SWITCH TEST 1. Swing control levers to outward position. 2. Disengage blade drive. 3. Put park brake in OFF position.
OPERATION INSTRUCTIONS 32 TESTING OF SAFETY INTERLOCK SYSTEMS The following tests should be performed at the start of each mowing day. BLADE DRIVE SWITCH TEST 1. Put park brake in ON position. 2. Swing control levers to outward position. 3. Engage blade drive.
OPERATION INSTRUCTIONS 33 MOWING WITH A MULCHING ATTACHMENT Mulching or recycling the grass clippings requires a totally different mowing approach than would be normal when side discharging or bagging the grass. There may be instances or conditions where it is not possible to hide all the recycled or mulched clippings.
OPERATION INSTRUCTIONS 34 MOWING WITH A MULCHING ATTACHMENT (continued) 7. Keep the underside of the mower deck clean. Remove all grass and dirt buildup from the underside of the pan, the baffles and deflectors after each use.
OPERATION INSTRUCTIONS 35 MOWING WITH A GRASS CATCHER ATTACHMENT In order to achieve optimum performance when mowing with a grass catching attachment, please read and follow the tips listed below. 1. Read and follow the installation instructions that are included with your grass catcher.
OPERATION INSTRUCTIONS 36 MOWING WITH A GRASS CATCHER ATTACHMENT (continued) WARNING ! Failure to observe the following instructions could result in serious injury or death. 7. Maintain sharp blades throughout the cutting season. Some grass catching attachments require a “high-lift” blade.
OPERATION INSTRUCTIONS 37 SIDE DISCHARGE OF THE CLIPPINGS In order to achieve optimum performance when side discharging the grass clippings, please read and follow the tips listed below. Additional information can be found in the Troubleshooting guide on Page 48-49.
OPERATION INSTRUCTIONS 38 GRASS HEIGHT AND CUTTING SUGGESTIONS Do not attempt to cut grass when it is wet. If the grass is tall, place the mower deck cut height lever in the top or second notch. “Initially” overlap cutting swaths instead of a full swath with each pass.
OPERATION INSTRUCTIONS 39 TOWING TRAILERS AND OTHER ATTACHMENTS Towing a trailer or other attachment that is too heavy could damage the drive or cause the mower to become unstable.
CARE AND MAINTENANCE 40 Before performing any maintenance, turn off engine, allow to cool and remove key. Use extreme care when working on machinery. Do not wear watch or jewelry. Do not wear loose fitting clothes, and observe all common safety practices with tools.
CARE AND MAINTENANCE 41 CAUTION ! Stop engine and remove ignition key for safety. Wear heavy, thick gloves when holding onto cutter blade, avoid the sharp edge of the blade. Blades should be discarded when worn excessively. DANGEROUS! Do not use blade in this condition! When notch starts, discard blade New blade — Fig.
CARE AND MAINTENANCE 42 BELTS Check belts every 100 hours. Replace any belts showing signs of severe cracking or large nicks. Belts are not adjustable, replace if they begin to slip from wear.
CARE AND MAINTENANCE 43 TIRES Correct tire pressure is essential for efficient operation of the mower. Check tire pressure periodically. Inflate tires to the pressure listed below. Front tires 11 x 4.50 - 5 15 PSI (103 kPa) Rear tires 18 x 9.50 - 8 15 PSI (103 kPa) Lug nuts or lug bolts should be checked regularly for tightness.
CARE AND MAINTENANCE 44 Hex Head Valve Stem CHANGING THE ENGINE OIL 1. The “Dapco” oil drain valve is located on the left side of the engine crankcase. 2. Place a suitable container under the drain valve hose. 3. To drain, turn hex head valve stem counter-clockwise with a 10mm wrench or socket.
CARE AND MAINTENANCE 45 TRACKING ADJUSTMENT If the mower is not tracking straight, check the air pressure in both rear tires. Recommended air pressure is 15 PSI (1 bar). If the unit will not track straight, follow the steps below. Tracking must be checked on a flat and level concrete or blacktop surface.
CARE AND MAINTENANCE 46 MOWER DECK LEVELING PROCEDURE There are four (4) slots that will control the attitude or pitch of the mower deck. The deck should be level or pitched slightly higher in rear. 1. Place the mower on a smooth level surface with front casters positioned towards deck.
CARE AND MAINTENANCE 47 ELECTRICAL SYSTEMS Keep all connections clean and tight. CLEANING THE MOWER Wash mower periodically. Clean above and below deck. High pressure washing and alkaline based soaps can cause damage to bearings and other parts of the mower.
48 TROUBLESHOOTING 1. ENGINE WON’T TURN OVER Mower blades engaged - - - - - - - - - - - - - - - - - - - - disengage blades Park brake not on - - - - - - - - - - - - - - - - - - - - - - - - engage pa.
49 TROUBLESHOOTING 6. ENGINE RUNS BUT MOWER WON’T MOVE FORWARD Drive belt broken or slipping - - - - - - - - - - - - - - - - - replace drive belt Transmission oil low - - - - - - - - - - - - - - - -.
50 STANDARD SERVICE PARTS LIST BLADES 44" Deck * Hi Lift Fusion P/N 539 119836 Super Hi-Lift Fusion P/N 539 119798 Standard Lift Fusion P/N 539 119860 Gator Fusion P/N 539 119862 Hi-Lift P/N 539 .
Dixon ~401 North Commerce Street~Beatrice, NE~68310 ~402-223-1000~Fax 402-223-1053 OWNER’S INFORMATION Date of Purchase ________________________________ Mower Model Number __________________________.
Dixon and ZTR® are registered trademarks of Dixon DIXON 401 Commerce Street Beatrice, NE 68310 Ram Series Part No. 539 114246IR WARNING ! The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
Ein wichtiger Punkt beim Kauf des Geräts Dixon RAM 50 MAG (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Dixon RAM 50 MAG noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Dixon RAM 50 MAG - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Dixon RAM 50 MAG reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Dixon RAM 50 MAG erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Dixon RAM 50 MAG besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Dixon RAM 50 MAG verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Dixon RAM 50 MAG. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Dixon RAM 50 MAG gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
