Benutzeranleitung / Produktwartung 12828-0603 des Produzenten Dixon
Zur Seite of 44
Model Y Model Y Model Y Model Y Model Y ear 200 ear 200 ear 200 ear 200 ear 200 4 4 4 4 4 ZTR® Model 2 Model 2 Model 2 Model 2 Model 2 700 700 700 700 700.
IMPORTANT - READ CAREFULLY The Dixon ® ZTR ® Mower is both easy and fun to operate. However, any power mower must be oper- ated properly to be safe. It is not a toy or a recre- ational vehicle. Before you start to use the mower, read the operator’s manual carefully and become completely familiar with the controls.
3 INDEX Page Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12 Warranty Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Controls . .
4 RIDING LAWN MOWERS, IF IMPROPERLY OPERATED, CAN CAUSE SERIOUS INJURY OR DEATH. The most common causes of injury to the operator or bystander... ...read and understand this manual to prevent injuries.
5 Safety Alert Symbol When you see this symbol, BE ALERT to the potential for injury. DANGER (highlighted in red) indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
6 Failure to observe the following safety instructions could result in serious injury or death. GENERAL OPERATION: • Read, understand, and follow all instructions in the manual and on the mower before starting. •Only allow responsible adults, who are familiar with the instructions, to operate the mower.
7 GENERAL OPERATION (continued) : •Turn off blades when not mowing. •Stop engine before removing grass catcher or unclogging chute. •Mow only in daylight or good artificial light. •Do not operate the mower while under the influence of alcohol or drugs.
8 SLOPE OPERATION: Slopes are a major factor related to loss-of-control and tip- over accidents, which can result in severe injury or death. All slopes require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it ! DO •Mow across the slope with your Dixon ZTR - never up or down.
9 •Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly down the slope. •If front wheels lift off the ground, pull the levers back to stabilize the mower. DO NOT • Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible.
10 SAFETY CHILDREN: Tragic accidents can occur if the operator is not alert to the presence of children. Children are attracted to lawn mowers and the mowing activity. NEVER assume children will stay where they were last seen. Be alert to avoid accidents.
11 SERVICE: •Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive. Use only an approved container. Never remove fuel cap or add fuel with engine running. Allow engine to cool before refueling. Do not smoke while refueling.
12 SERVICE (continued): •Never run a mower inside a closed area. The exhaust fumes are toxic. •Keep nuts and bolts tight, especially blade attachment bolts, and keep equipment in good condition. •Never tamper with safety devices. Check their proper operation regularly.
13 DIXON LIMITED W ARRANTY POLICY COMMERCIAL MODELS - 2700 SERIES DIXON ZTR MOWERS ARE W ARRANTED AGAINST DEFECTS IN MA TERIALS AND WORKMAN- SHIP AND PROVIDES FOR REPLACEMENT OR REP AIR OF P ARTS INCLUDING LABOR COSTS. THIS WARRANTY IS SUBJECT TO THE FOLLOWING CONDITIONS AND LIMIT A TIONS.
14 SPECIFICATIONS Model 2700 CHASSIS: 11 GA - rectangular tube, 7 GA reinforcement SEAT: Designed for operator comfort with padded back & arm rests. Seat is adjustable fore & aft. Mounted on operator suspension system. MOWER DECK: 2 decks are available.
15 CONTROLS CONTROL LEVERS Note: For access to the seat, move control levers to neutral position and swing them outward. TO GO FORWARD: • From neutral position, gently push both control levers forward. • To increase speed, move levers further forward.
16 CONTROLS SEAT: Fore & Aft: Move lever, slide seat fore & aft to desired position, release. PARKING BRAKE: A parking brake is located to the left of the seat. The engine will kill if control levers are not in the outboard position when the parking brake is engaged.
17 CONTROLS MOWER BLADE SWITCH: To engage blades: pull up on switch To disengage blades: push down IGNITION SWITCH: • Turn to start position to crank engine. Release when it starts. • For headlights - rotate switch one notch counter-clockwise from run.
18 CONTROLS.
19 OPERATION INSTRUCTIONS The safe and successful operation of the ZTR Model 2700 will depend upon the operator having the correct knowledge of all controls used on the mower and making good judgements about the terrain to be mowed. NEVER allow anyone to operate the mower without complete knowledge of all controls and their func- tions.
20 OPERATION INSTRUCTIONS TESTING OF SAFETY INTERLOCK SYSTEMS: Do not operate mower if safety switches are not operating properly. Your Zero Turning Radius Mower is equipped with control interlocks for your safety. 1 . The engine will not start if the mower blades are engaged.
21 INTERLOCK SWITCH TEST Note: Operator must be seated in normal operating position to perform these tests. 1 . With engine off, turn mower blade on and attempt to start engine. ENGINE SHOULD NOT START. 2 . With engine off, move control levers in and attempt to start engine.
22 OPERATION INSTRUCTIONS STARTING INSTRUCTIONS: 1. Operator must be seated in normal operating position. 2. Set parking brake. 3. Move control levers to outboard position. 4. Assure blade clutch is off. 5. Push throttle control lever to 1/2 setting. 6.
23 OPERATION INSTRUCTIONS MOWING INSTRUCTIONS: CAUTION Be sure that deflector is properly installed on the discharge chute. 1 . Start engine and set throttle at full speed. 2 . Set desired cut height. 3 . Release park brake. CAUTION Check the area to assure there is no one near.
24 OPERATION INSTRUCTIONS GRASS HEIGHT AND CUTTING SUGGESTIONS: Do not attempt to cut grass when it is wet. If the grass is tall, place the mower deck cut height lever in the top or second notch. “Initially” overlap cutting swaths instead of a full swath with each pass.
25 OPERATION INSTRUCTIONS TO LIFT SEAT: To lift the seat, move the control levers to the neutral “OUT” position. Release the seat latch and rotate the counterbalanced seat support frame upward and forward.
26 OPERATION INSTRUCTIONS TO FREE WHEEL MACHINE (UNLOCK TRANSMISSION): Always turn off engine before engaging or disengaging the hydro release (free wheel) valves. Never attempt to move the valves with the engine running. The hydro release valves are located beneath the seat on the top of the hydro pumps on each side of the machine.
27 CARE AND MAINTENANCE CAUTION CAUTION CAUTION CAUTION CAUTION Before performing any maintenance, turn off engine, allow to cool & remove k ey . Use extreme care when working on machinery . Do not wear w atch or jewelry . Do not wear loose fitting clothes, and observe all common safety practices with tools.
28 CARE AND MAINTENANCE ENGINE: For complete maintenance and operating information of the engine, please refer to the maintenance instructions furnished by the engine manufacturer and included in your Zero Turn Radius mower information packet. Note: Air intake screen must be kept clean.
29 MOWER BLADES: Check sharpness of mower blades after every 10 hours of opera- tion. To sharpen blades, proceed as follows. 1. Remove bolt and flat washer mounting blade on shaft. Remove blade. 2. Blades should be discarded when worn excessively. 3. Sharpen blade with a hand file, electric grinder or blade sharpener.
30 CARE AND MAINTENANCE LUBRICATION: ENGINE: Follow engine manufacturer’s recommenda- tion. DECK SPINDLES: Lubricate with 3 “shots” only, every 100 hours. MOWER CHASSIS: Lubricate with 3 “shots” only, every 50 hours (see zerk locations below).
31 CARE AND MAINTENANCE CHECKING & REPLENISHING OIL IN HYDROSTATIC TRANSMISSION: Dirt or water in oil can ruin the hydrostatic transmissions. Check the oil level in hydrostatic transmission oil reservoir after every 25 hours of usage. Clean the oil reservoir cap and the area around it prior to removal.
32 CARE AND MAINTENANCE PARKING BRAKE ADJUSTMENT 1 . Raise rear of machine. 2 . Remove tire and wheel assembly. 3 . Adjust the 3/8” adjustment nut clockwise to increase and counter-clockwise to decrease brake holding power. As the brake holding power is increased, the force required on the handle to engage the brake increases.
33 1 . Loosen the 1/2” retaining nut underneath the headlight and slide the headlight forward out of the recessed area of the fuel tank. 2 . Loosen the 1/2” nut on the “U” shaped holding bracket and swivel the headlight vertically to adjust the height of the beam.
34 CARE AND MAINTENANCE HYDROSTATIC PUMPS: Before each use, check to be sure that the cooling fins of the hydrostatic pumps are clean. Excessive accumulation of oil, dirt, or trash may cause the pumps to overheat. NEVER WASH ACROSS TOP OF RESERVOIR WITH WATER OR STEAM.
35 STEERING CONTROL ADJUSTMENTS: To adjust neutral: 1. Lift seat (see instructions on Page 25). 2 . Block up the unit so that the drive wheels are off the ground. 3 . Loosen ball joint jam nuts on control rod. Note: The front jam nuts are left hand threads.
36 STEERING CONTROL ADJUSTMENTS (continued): CARE AND MAINTENANCE To adjust steering control levers: 1. Loosen the front and rear bolts retaining the bellows hold down plate and slide the bellows and plate up the steering lever to expose the steering control mechanism.
37 To adjust “In” position of the steering controls 1. Move the levers inboard to the operating position. 2 . Adjust the steering lever stops until the steering levers have the desired clearance. To adjust for straight forward tracking. 1. Drive tractor with both control levers in the full forward position.
38 CARE AND MAINTENANCE LEVELING THE DECK: 1 . Set the tire pressure on all four tires. 2 . Front casters must be rotated in the direction of forward travel. 3 . Move the tractor to a hard level surface. 4 . Put the mower deck in the number 3 deck height position.
39 STANDARD SERVICE PARTS LIST ZTR MODEL 2700: Blades (60”) standard: P/N 12421 low lift: P/N 12451 Gator: P/N 12508 Blades (72”) standard: P/N 12339 low lift: P/N 12452 Gator: P/N 12509 Engine to.
40 1. ENGINE WON’T TURN OVER Mower blades engaged- - - - - - - - - - - - - - - - - - - - - - - - - - - -disengage blades Drive not in neutral - - - - - - - - - - - - - - - - - -move control levers t.
41 TROUBLESHOOTING 6. ENGINE OVERHEATED Radiator coolant level- - - - - - - - - - - - - - - - - - - - - - - - - - - -add coolant mixture Air intake screen or fins clogged- - - - - - - - - - - - - - - .
42 CARE AND MAINTENANCE ELECTRICAL SYSTEMS: Keep all connections clean and tight. CLEANING THE MOWER: Wash mower periodically. Clean above and below deck. High pressure washing and alkaline based soaps can cause damage to bearings and other parts of the mower.
43 OWNER INFORMATION Date Purchased _ ________________________________ Mower Model Number ____________________________ Mower Serial Number ____________________________ Purchased From ___ _____________.
ZTR®Mowers ZTR®Mowers ZTR®Mowers ZTR®Mowers ZTR®Mowers Dixon® and ZTR® are registered trademarks of Dixon Industries, Inc. DIXON INDUSTRIES, INC. a BLOUNT International Inc. Co. P.O. Box 1569 Coffeyville, Ks 67337-0945 620-251-2000 Model 2700 Part No.
Ein wichtiger Punkt beim Kauf des Geräts Dixon 12828-0603 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Dixon 12828-0603 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Dixon 12828-0603 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Dixon 12828-0603 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Dixon 12828-0603 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Dixon 12828-0603 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Dixon 12828-0603 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Dixon 12828-0603. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Dixon 12828-0603 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
