Benutzeranleitung / Produktwartung HCCA-D1200 des Produzenten Directed Electronics
Zur Seite of 24
W arranty LIMITED TWO YEAR CONSUMER WARRANTY : Directed Electronics promises to the original purchaser , to replace this product should it prove to be defective in workmanship or material under normal.
CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 What’ s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION Thank you for your purchase of Orion's HCCA-D1200, HCCA-D2400, or HCCA-D5000 power amplifier . Each Orion amplifier is designed to be the leader in its class of fering the most power , advanced features, and extreme ease of use.
PRACTICE SAFE SOUND™ Continuous exposure to sound pressure levels over 100dB may cause permanent hearing loss. High power automotive sound systems can generate sound pressure levels in excess of 130dB. When playing your system at high levels, please use hearing protection and avoid long term exposure.
10. Phase Control Switch - provides either 0 or 180 degree phase shift of the ampli- fied output (speaker) with respect to the input signal to facilitate bridging of amplifiers. 11. Power LED - when illuminated (green) indicates that the amplifier is on.
5 © 2006 Directed Electr onics, all rights reserved 2. +BA T - connect this terminal through a FUSE or CIRCUIT BREAKER to the positive terminal of the vehicle battery or the positive terminal of an isolated audio sys- tem battery .
6 © 2006 Directed Electr onics, all rights reserved SPECIFICA TIONS 1. Continuous 4 W load 20Hz to 200Hz, < 1% THD, with input voltage at 14.4VDC. 2.
7 © 2006 Directed Electr onics, all rights reserved AMPLIFIER SETTINGS Signal Input and Output Configurations The input section of the amplifier consists of a phase switch that sets the output configura- tion, infrasonic switch, gain controls, high pass and low pass crossovers controls, Intelli-Q control, and RCA inputs.
8 © 2006 Directed Electr onics, all rights reserved WARNING! DO NOT set crossover frequencies lower than the speakers recommended operating range. This can cause driver failure that is not covered by the man- ufacturer's warranty . Low-Pass Crossover When the switch is to the left (OFF position), the low-pass crossover is bypassed.
9 © 2006 Directed Electr onics, all rights reserved Infinite Baffle Example High-Pass Set at 30Hz By removing low frequency signal that the woofer cannot produce, the woofer can play its capable range louder . The first example is an infinite baf fle situation.
10 © 2006 Directed Electr onics, all rights reserved Sealed Example High-Pass Set at 20Hz This sealed example is the same 12-inch woofer in the recommended sealed enclosure. Up to 6 dB of boost is capable if 20 Hz was used. With +6dB of boost, the woofer has more out- put down to 15 Hz.
11 © 2006 Directed Electr onics, all rights reserved Remote Gain Operation NOTE: Do not use the Remote Gain control when you have an expanded system installed (see Line Ouput Configurations ).
12 © 2006 Directed Electr onics, all rights reserved Speaker Connections The Orion HCCA-D1200, HCCA-D2400, and HCCA-D5000 amplifiers offer two positive and two negative output terminals for ease of connecting the speakers to the amplifier . Since these are mono amplifiers, the speaker connectors are paralleled internally .
13 © 2006 Directed Electr onics, all rights reserved AMPLIFIER INST ALLA TION Choosing Mounting Locations The location of your amplifier will depend on several important issues. Due to the low pro- file size of the Orion amplifiers, there are many possible installation locations that will yield satisfactory amplifier performance.
14 © 2006 Directed Electr onics, all rights reserved General Precautions and Installation Tips WARNING! Be careful not to cut or drill into gas tanks, fuel lines, brake lines, hydraulic lines, vacuum lines, or electrical wiring when working on your vehicle.
15 © 2006 Directed Electr onics, all rights reserved ● RT A (real time analyzer) ● Soldering iron and solder ● Utility knife ● Wire brush or sandpaper for chassis grounding ● Wire crimper ● Wire cutters ● Wire strippers Step By Step Installation Step 1 Determine the location for the amplifier .
16 © 2006 Directed Electr onics, all rights reserved SET UP AND TROUBLESHOOTING T esting the System After you have completed the installation, you need to test the system. This will help ensure years of trouble-free operation. Please refer to the listed steps below when testing the sound of your Orion system.
17 © 2006 Directed Electr onics, all rights reserved Step 6 T urn up the level control corresponding to the tweeter output until you hear slight distortion and turn back the level control slightly for an undistorted output. Depending on your system the midrange and tweeter output may be on the same output channels.
18 © 2006 Directed Electr onics, all rights reserved T r oubleshooting Tips Symptom Probable Cause Action T o T ake No output Low or no remote turn-on Check remote turn-on voltage at voltage amplifier and repair as needed. Fuse blown Check power wire's integrity and check for speaker shorts.
Symptom Probable Cause Action T o T ake Distorted output Internal crossover not set Readjust crossovers. Refer to the properly for speakers Internal Crossover Configuration section of this guide for detailed instructions. Speakers are blown Check system with known work ing speakers and fix or replace as needed.
APPENDIX—PROGRAMMABLE FEA TURES The following listing are ESP ® -2 features that can be programmed or accessed by your installer to customize or troubleshoot your system. Factory default settings are shown in bold. NOTE: The Bitwriter ® must have software version 2.
NOTE: Use caution when adjusting or unlocking gain as restricting the range or unlock- ing the range can result in sudden increases in gain. The V alet Monitoring and Anti Theft options (below) require the ESP2 alarm to be “learned” into the amplifier .
Event 1 through 7 - Stores up to seven recent events that have occurred to aid in diagnos- tic troubleshooting. The events that are retained are: Undervoltage, Overvoltage, Reserved, No Fault, Thermal, Overcurrent. These events are read-only , they cannot be written to the amplifier by the installer .
NOTES ____________________________________________________ ____________________________________________________ ____________________________________________________ ___________________________________.
Ein wichtiger Punkt beim Kauf des Geräts Directed Electronics HCCA-D1200 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Directed Electronics HCCA-D1200 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Directed Electronics HCCA-D1200 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Directed Electronics HCCA-D1200 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Directed Electronics HCCA-D1200 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Directed Electronics HCCA-D1200 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Directed Electronics HCCA-D1200 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Directed Electronics HCCA-D1200. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Directed Electronics HCCA-D1200 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
