Benutzeranleitung / Produktwartung 350HV des Produzenten Directed Electronics
Zur Seite of 29
© 2005 Directed Electr onics , Inc . Vista, CA N426V 07-05 NO TE: This product is intended f or installation by a prof essional installer only! Any attempt to install this product b y any person other than a trained prof essional ma y result in sev ere damage to a v ehicle’ s electrical system and components.
Bitwriter™, Code H opping™, , Doubleguar d ® , ESP™, F ailSafe ® , Ghost S witch™, Learn Routine™, N ite-Lite ® , N uisance Pr evention ® Circuitry , NPC ® , Revenger ® , Silent M ode.
© 2005 Directed Electronics, Inc. all rights reser ved 3 T able of Contents P P r r i i m m a a r r y y H H a a r r n n e e s s s s ( ( H H 1 1 ) ) W W i i r r e e C C o o n n n n e e c c t t i i o o n n G G u u i i d d e e . . . . . . . . . . . . . .
4 © 2005 Directed Electronics, Inc. all rights reser ved Primary Harness (H1) Wire Connection Guide Primary Harness Wiring Diagram ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ Primary Harness Wiring Instructions This guide describes in detail the connection of each wire.
© 2005 Directed Electronics, Inc. all rights reser ved 5 H1/2 WHITE (+/-) light flash output As shipped, the H1/2 WHITE wir e should be connected to the (+) parking light wire. If the light flash polarity jumper is mov ed to the (-) position (see the Programming Jumper section of this installation guide), this wire supplies a (-) 200 mA output.
6 © 2005 Directed Electronics, Inc. all rights reser ved H1/3 WHITE/BLUE 200 mA (-) channel 3 output This wire pro vides a (-) 200 mA output whenever the transmitter button(s) controlling channel three is pr essed.
© 2005 Directed Electronics, Inc. all rights reser ved 7 H1/5 GREEN (-) door trigger input M ost vehicles use negative door trigger circuits. Connect the gr een wire to a wire sho wing ground when any door is opened. When connecting to newer model v ehicles there is generally a need to use individual door triggers.
8 © 2005 Directed Electronics, Inc. all rights reser ved H1/8 BLACK (-) chassis ground connection Connect this wire to a clean, paint-fr ee sheet metal location (driver kick panel) using a factor y bolt that DOES NO T have any vehicle component grounds attached to it.
© 2005 Directed Electronics, Inc. all rights reser ved 9 H1/11 RED (+)12V constant power input Before connecting this wir e, remo ve the supplied fuse. Connect to the battery positive terminal or the constant 12V supply to the ignition switch. NO TE: Always use a fuse within 12 inches of the point you obtain (+)12V .
10 © 2005 Directed Electronics, Inc. all rights reser ved Door Loc k Harness (H2), 3-PIN Connector ___ ___ ___ NO TE: For detailed instructions about connecting to the vehicle ’ s power door lock systems, refer to the Door Lock Wiring guide (D ocument N o.
© 2005 Directed Electronics, Inc. all rights reser ved 11 V alet/Program Switch, 2-Pin BLUE Plug The V alet/Pr ogram button should be accessible from the driver ’ s seat. It plugs into the BL UE por t on the side of the unit. Since the system featur es V alet® by using the remote transmitter , the button can be well hidden.
12 © 2005 Directed Electronics, Inc. all rights reser ved 3. M ount the receiver/antenna using the supplied double-sided tape. 4. Route the r eceiver/antenna cable to the control module and plug it into the four-pin antenna connector . On-Boar d Dual-Stage Shoc k Sensor There is a dual-stage shock sensor inside the control unit.
© 2005 Directed Electronics, Inc. all rights reser ved 13 Optional Sensor Harness, 4-pin Connector The four-pin sensor harness is optional, and is not included with this unit. RED (+) 12V Constant and BLACK (-) Ground These wires supply constant (+) 12 volts and gr ound to the optional sensor .
14 © 2005 Directed Electronics, Inc. all rights reser ved Bypassing Sensor Inputs There ar e times when you need to temporarily bypass all sensor inputs to the unit, such as when remote starting the vehicle. Anytime an auxiliary channel output is used, all inputs are bypassed for 5 seconds.
© 2005 Directed Electronics, Inc. all rights reser ved 15 2. I I g g n n i i t t i i o o n n . . T urn the ignition on, then back off: (The H1/9 YELLO W wire must be connected.) 3. S S e e l l e e c c t t a a M M e e n n u u . . P ress and HOLD the V alet/P rogram switch: (The V alet/P rogram switch must be plugged into the blue port.
16 © 2005 Directed Electronics, Inc. all rights reser ved To access another feature in the same menu: 1. P ress and release the V alet/P rogram switch the number of times necessar y to advance fr om the feature you just pr ogrammed to the next one you want to program.
© 2005 Directed Electronics, Inc. all rights reser ved 17 System Features Menus Menu #1 - Basic Features I tems in bold text have been programmed to the default setting at the factory .
18 © 2005 Directed Electronics, Inc. all rights reser ved Feature Descriptions The features of the system ar e described below . F eatures that have additional settings that can be selected only when.
© 2005 Directed Electronics, Inc. all rights reser ved 19 setting is 0.8 second door lock pulses. F or some vehicles a 0.4 second pulse duration is required to prevent the windo ws from mo ving. 1-7 FORCED PASSIVE ARMING ON/OFF: T o use this feature, passive arming must be selected in step 1-1.
20 © 2005 Directed Electronics, Inc. all rights reser ved 2-3 NUISANCE PREVENTION ® CIRCUITRY (NPC ® ) ON/OFF: NPC ® ® stops repeated triggering of the same zone. If one zone is trigger ed three times in one hour , that zone is bypassed for one hour , star ting from the time of the thir d trigger .
© 2005 Directed Electronics, Inc. all rights reser ved 21 2-9 DOUBLE/SINGLE PULSE LOCK: Some vehicles r equire two pulses on a single wir e to unlock the doors. When the double pulse unlock featur e is turned on, the BLUE H2/C wir e will supply two negative pulses instead of a single pulse.
22 © 2005 Directed Electronics, Inc. all rights reser ved 3. S S e e l l e e c c t t t t h h e e r r e e c c e e i i v v e e r r c c h h a a n n n n e e l l : : P ress and release the V alet/P rogram button the number of times necessary to access the desired channel.
© 2005 Directed Electronics, Inc. all rights reser ved 23 5. R R e e l l e e a a s s e e . . Once the code is learned, the V alet/P rogram button can be released. To exit the learn routine: One long chirp indicates that Learn Routine has been exited.
24 © 2005 Directed Electronics, Inc. all rights reser ved operates Arm only operates Disarm only operates Channel 2 and Silent M ode operates P anic and operate Channel 3 The expanded configuration also allows the user to utilize M ulti-Level S ecurity Arming, a feature that cannot be accessed from a standar d configuration transmitter .
© 2005 Directed Electronics, Inc. all rights reser ved 25 System Status Chirps T able of Zones NO TE: The W arn A way® response does not report on the LED. Long T erm Event Histor y The system stores the last two full triggers in memory . These are not erasable.
26 © 2005 Directed Electronics, Inc. all rights reser ved 1. With the ignition off , press and HOLD the V alet/P rogram switch. 2. T urn on the ignition. 3. Release the V alet/P rogram switch. 4. P ress and release the V alet/P rogram switch within 5 seconds.
© 2005 Directed Electronics, Inc. all rights reser ved 27 within a one hour period. F or a full description of NPC operations refer to the owner's manual. Rapid Resume Logic Rapid Resume Logic ensur es that the when the system is power ed up it will return to the same state it was in when power is disconnected.
28 © 2005 Directed Electronics, Inc. all rights reser ved Door input does not respond with the progressive trigger, but with immediate full alarm. ➤ What zone does the LED indicate? If the LED indicates that the impact sensor caused the trigger , the sensor may be detecting the door opening.
© 2005 Directed Electronics, Inc. all rights reser ved 29 Wiring Quic k Reference Guide.
Ein wichtiger Punkt beim Kauf des Geräts Directed Electronics 350HV (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Directed Electronics 350HV noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Directed Electronics 350HV - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Directed Electronics 350HV reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Directed Electronics 350HV erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Directed Electronics 350HV besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Directed Electronics 350HV verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Directed Electronics 350HV. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Directed Electronics 350HV gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
