Benutzeranleitung / Produktwartung D26204K des Produzenten DeWalt
Zur Seite of 20
D26204- XE HEA VY -DUTY COMP ACT ROUTER INSTRUCTION MANU AL.
.
1 Definitions: Safety Guidelines The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury .
2 WARNING: T o reduce the risk of injur y , user must read the instr uction manual. GENERAL POWER TOOL SAFETY WARNINGS WARNING! R ead all safety warnings and all instructions Failure to follow the warnings and instr uctions may result in electric shock, fire and/or serious injur y .
3 b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools.
4 • Hearing protection: AS/NZS1270 Acoustics – Hearing Protection; • Respiratory protection: AS/NZS1716 Respirator y Protective Devices. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other constr uction activities contains chemicals known to cause cancer , bir th defects or other reproductive harm.
5 A E D F C B G L J Q FIG. 1 ROUND SUBBASE D-SUBBASE I K H FIXED BASE M N O P R PL UNGE BASE.
6 .............. Class II Constr uction .............ear thing terminal ................... (double insulated) ..............safety aler t symbol …/min ........ per minute BPM ..........beats per minute IPM ............. impacts per minute RPM .....
7 Cutter Installation and Removal (Fig. 1, 3) WARNING: T o reduce the risk of injury , turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An accidental star t-up can cause injur y .
8 Excessive force should not be used to clamp the locking lever . Using excessive force may damage the fixed base. When the locking lever (I) is clamped the motor (J) should not move in the fixed base. Adjustment is needed if the locking lever will not clamp without excessive force or if the motor moves in the fixed base af ter clamping.
9 5. While holding down on the cone, tighten the subbase screws. LL LL T FIG. 6A FIXED BASE FIG 6B LL LL PL UNGE BASE T Using T emplate Guides The plunge subbase will accept template guides. On the fixed base an accessor y subbase will be needed to accept template guides.
10 Using a P arallel F ence (Fig. 8A) A basic parallel fence is included with the D26204- XE and works with the fixed base. The basic parallel fence D262003- XJ is available as an accessor y for the other models and may be purchased from your local retailer or ser vice center at extra cost.
11 FIG. 9 V W FIG. 10 HH II KK JJ U X 4. When using vacuum attachment, be aware of the placement of the vacuum cleaner . Be sure that the vacuum cleaner is stable and that its hose will not inter fere with the work. Vacuum Attachment (Plunge Base Only , Fig.
12 Set-up: Plunge Base INSERTING THE MOTOR INTO THE PL UNGE BASE (FIG. 1, 11) WARNING: T o reduce the risk of injury , turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs.
13 FINE ADJUSTMENT OF ROUTING DEPTH (FIG. 12) WARNING: T o reduce the risk of injury , turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An accidental star t-up can cause injur y .
14 VARIABLE SPEED CONTROL (FIG. 1) This router is equipped with a variable speed dial (C) with an infinite number of speeds between 16000 and 27000 RPM. Adjust the speed by turning the variable speed dial (C). NOTICE: In low and medium speed operation, the speed control prevents the motor speed from decreasing.
15 ACCESSORIES WARNING: Since accessories, other than those offered by D E WAL T , have not been tested with this product, use of such accessories with this tool could be hazardous. T o reduce the risk of injur y , only D E WAL T recommended accessories should be used with this product.
.
.
Stanley Black & Decker 82 T ar yn Drive, Epping, VIC 3076 Australia • 1800 444 224 (Aust) or 0800 339 258 (NZ) www .dewalt.com.au • www .dewalt.
Ein wichtiger Punkt beim Kauf des Geräts DeWalt D26204K (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie DeWalt D26204K noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für DeWalt D26204K - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von DeWalt D26204K reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über DeWalt D26204K erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon DeWalt D26204K besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von DeWalt D26204K verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit DeWalt D26204K. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei DeWalt D26204K gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.