Benutzeranleitung / Produktwartung BHT-202B-CE/202BW-CE des Produzenten Denso
Zur Seite of 175
Bar Code Handy Terminal B H T - 202B-CE/202BW-CE User ’ s Manual.
DENSO W A VE INCORPORA TED does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.
US and Canada Regulations This device complies with Part 15 of the FCC Rules, Canadian ICES-0 03 and RSS-210 Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference receiv ed, including interference that ma y cause undesired operation.
LABELING: Grip style BHT For USA and Canada For USA and Canada For USA and Canada.
Declaration of Conformity (For Eur opean Union) The radio frequency module (T ype: LA-4137) that complies with the Directive 99/5/EC(R&TTE) is mounted on this device (BHT -202BW-CE). A Declaration of Conformity may be obtained from: http://www2.symbol.
i Pr eface Please READ through these operating instructions carefully . It will enable you to operate your BHT -202B-CE/202BW-CE correctly . The following contents are explained in this guide: • Han.
ii How this book is organized This manual is made up of five chapters and appendices. Chapter 1 Quick Guide Describes the basic operating method of the BHT and the related notes.
iii Related Publications BHT -200-CE API Reference Manual BHT -200-CE Class Library Reference Manual 2D Code Scanner/Barcode Scanner Keyboard Interface with BHT -CE kbifCE User ’s Guide Screen In dication The lettering in the screens in this manual is a little different from that i n the actual screens.
iv SAFETY PRECAUTIONS Be sure to observe all these safety pr ecautions. Please READ through this manual carefully . It will enable you to use the BHT and CU correctly .
v Handling the battery cartridge • Never disassemble or heat the battery cartridge, nor put it into fire or water; doing so could cause battery-rupture or leakage of battery fluid, resulting in a fire or bodily injury . • Do not carry or store the battery cartridge t ogether with metallic ball-point pens, necklaces, coins, hairpins, etc.
vi Handling the CU • If smoke, abnormal odors or noises come from the CU, immediately unplug the AC adapter from the wall socket or CU and contact your nearest dealer .
vii Handling the battery cartridge • Never charge a wet or damp rechargeable battery cartridge. Doing so could cause the batteries to break, generate heat, rupture or burn. Handling the BHT • If smoke, abnormal odors or noises come from the BHT , immediately turn off the power , pull out the battery cartridge, and contact your nearest dealer .
viii Handling the CU • Never disasse mble or modify the CU; doing so could result in an accident such as fire or malfunction. • Never put the CU in places where there are excessively high temperatures, such as inside closed-up automobiles, or in places exposed to direct sunlight.
ix Proper Care of the BHT and CU Clean the housings, BHT charge terminals, battery cartridge terminals, and CU-200 charge terminals with a dry , soft cloth. Before cleaning, be sure to turn the BHT power off and unplug the AC adapter of the CU. • Never use benzene, alcohol, or other organic solvents.
x DENSO W A VE INCORPORA TED does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.
Chapter 1 Quick Guide Chapter 2 Getting S tarte d the BHT and System Menu Chapter 3 Communications Operations of the BHT -202B-CE/202BW -CE Chapter 4 Error Messages Chapter 5 Handling the CU-200 (Opti.
1 Chapter 1 Quick Guide This chapter describes the basic operating method of the BHT and the related notes. 1.1 Reading Bar Codes .........................................................................................................................
2 1.1 Reading Bar Codes T urn the BHT on, bring the bar-code reading window to the bar code to be scann ed, and press the trigger switch. Pressing the trigger switch halfway emits a laser light to indicate the scanning range and pressing it fully turns on the illumination LED to scan the bar code.
Chapter 1 Quick Guide 3 • If the BHT fails to read due to specular effects or other factors, change the scanning angle of the rea ding windo w or the distance from codes as sho wn at right, and try it again. (S pecular effects occur when the reflection of the light from the bar code becomes e xce ssivel y strong.
4 1.2 Setting and Using the Hand S trap and St y l u s Setting the hand strap Using the hand strap Put your hand through the hand strap and hold the BHT as shown below .
Chapter 1 Quick Guide 5 Using the stylus The BHT has a touch screen LCD. With the stylus that comes with the BHT , you can operate keys, menus, and icons displayed on the touch screen. Before using the touch screen, be sure to set it up. (Refer to Chapter 2, Section 2.
6 1.3 Setting the Backlight Pressing the right-hand trigger switch ( M4 key) with the SF/ALP key held down activates or deactivates the backlight function.
Chapter 1 Quick Guide 7 1.4 Using the Keypad Entering Numerical Data T o enter numerical data, use the numerical keys and the ENT key . For example, to enter the number "120," press the 1 , 2 and 0 keys and then press the ENT key . If you type in any wrong value, press the C/BS (BS) key and then enter the correct one.
8 1.5 T ransferring Data Using radio link (BHT -202BW -CE only) Using radio waves, the BHT -202BW-CE may transfer data to an access point in a spread spectrum communications system. If there are too many comm unications errors, first make sure that the BHT -202BW -CE points directl y at an access point.
Chapter 1 Quick Guide 9 Using infrar ed link Using infrared rays, the BHT may transfer dat a directly to the host computer equipped with an IrDA interface port and other IrDA-compliant devices. • Mak e sure that there is no obstruction in the li ght path between the B HT and any tar get stations.
10 Using USB interface Using a USB interface cable, the USB interface ports of the BHT and a h ost computer can be connected, allowing data to be transferred to the host computer .
11 Chapter 2 Getting S tarted the BHT and System Menu This chapter summarizes the BHT system configuration and describes the operation including preparation and System Menu (which is required for the efficient use of application programs). 2.1 BHT System Configuration .
12 2.1 BHT System Configuration The BHT barcode data collection system requires the following hardware as well as the BHT Bar Code Handy T erminal (which reads bar codes and accepts keypad entry), depending upon the intended system configuration.
Chapter 2 Getting Started the BHT and System Menu 13 In addition, the BHT -202BW-CE may operate in a radio communications system (spread spectrum communication) by connecting with access points by a wireless local area network (wireless LAN).
14 BHT Operating System (OS) Microsoft Windows CE .NET 5.0 Application Pr ogram Development Environment PC for application development Item Description OS Microsoft Windows 2000 Professional Servi.
Chapter 2 Getting Started the BHT and System Menu 15 Application Development T ool Microsoft eMbedded V isual C++ 4.0 Service Pack 4 or later , Microsoft Visual S tudio .NET or Microsof t Visual S tudio .NET 2003 Y ou can download Microsoft eMbedded V isual T ools 4.
16 2.2 Components 2.2.1 Names and Functions Indicator LED Illuminates in blue when the BHT has successfully read a bar code. Synchronization LED* Flashes during wireless communication. T o uch screen LCD (li quid crystal display) Shows the characters and graphic patterns.
Chapter 2 Getting Started the BHT and System Menu 17 Grip style BHT T rigger switch (M5 key) Press this switch to star t bar code reading. • Press this halfway to emit a laser light.
18 The functions of the keys may be set by user programs. Shown below is a set of sample functions. 30-key pad T rigger switch (M3 ke y) C (Clear) / BS (Backspace) key Moves back one character . Pressing this key with the SF key held down in BhtShell returns to the previous screen.
Chapter 2 Getting Started the BHT and System Menu 19 26-key pad T rigger switch (M3 key) T rigger switch (M4 key) Magic keys [M1] to [M5]* These keys may be used as an SF key , ENT key , CTRL key , AL.
20 2.2.2 S tatus Indicators on the LCD Windows desktop on 30-key pad type Windows desktop on 26-key pad type Battery volt age level Shows the current battery voltage level. Displays when the voltage level is high. Displays when the voltage level is low .
Chapter 2 Getting Started the BHT and System Menu 21 Synchronization state (Provided on the BHT -202BW-CE) Displays the open state of the wireless device and the radio field intensity . Displays when the wireless device is open. Shows the radio field intensity with the number of bars.
22 2.2.3 Notes for Using the BHT Windows desktop on the LCD The Windows desktop shown in this manual may be a little different fro m that in the actual screens on the LCD. (Windows desktop sample) This task tray also may be a little dif ferent from that in the actual screen.
Chapter 2 Getting Started the BHT and System Menu 23 2.3 Pr eparation 2.3.1 Setting-up 1: Load ing the battery cartridge Before the first use of the BHT , be sure to load the battery cartridge as sho wn below . The battery cartridge is not loaded in the BHT when shipped from the factory .
24 Into the grip (1) Take the bottom cover off the grip by removing the screw. (2) Pull the lock in the direction of the arrow and insert the battery cartridge into the grip with the boss facing as shown below. (3) Secure the bottom cover to the grip with the screw.
Chapter 2 Getting Started the BHT and System Menu 25 • Never disassemble or heat the battery cartridge, nor put it into fire or water; doing so could cause battery-rupture or leakage of battery fluid, resulting in a fire or bodily injury .
26 Battery V oltage Level on the S tatus Indicator Line The battery voltage level is always displayed on the status indicator line. (For details, refer to Section 2.
Chapter 2 Getting Started the BHT and System Menu 27 Grip style BHT As long as the voltage level of either one of battery cartridges loaded in the BHT body and grip is higher than the specified level, no low battery messages will appear . If any low battery message appears, therefore, you need to replace both battery cartridges.
28 2.3.2 Setting-up 2: Calibrating the touch scr een Press the power key to turn on the BHT . The calibration screen appears, so follow the on-screen instructions. If nothing appears, first perform a "cold boot" (refer to Section 2.3.5). The "+" appears first at the center of the screen as shown at left.
Chapter 2 Getting Started the BHT and System Menu 29 2.3.3 Battery Replacement Notes When is battery r eplacement needed? If the "Charge the battery!" appears on the LCD, replace the battery cartridge with a fully charged one.
30 2.3.4 BHT Turning-off Notes [ 1 ] "Shutdown in progress" message If you press the power key to turn off the BHT , the BHT displays the following message and starts preparation for shutdow n. When the above message is displayed, do not remove the battery cartridge.
Chapter 2 Getting Started the BHT and System Menu 31 [ 2 ] Backing up the Registry The Registry is the part of Windows CE that stores setup information required for operating the BHT .
32 2.3.5 W arm and Cold Booting W a rm-booting the BHT In any of the following cases, warm-boot the BHT : - The BHT makes no response to entry from the touch screen or keys.
Chapter 2 Getting Started the BHT and System Menu 33 Cold-booting the BHT If a problem persists even after w arm-booting the BHT , cold-boot the BHT . Cold-booting the BHT will erase all data stored in th e RAM. It is recommended that important data be saved into the FLASH folder or up lo aded to the host computer .
34 2.4 Replacement of the Backup Battery If the following warning message appears on the LCD, you need to replace the backup battery (refer to Section 2.4.1). If you rem ove the bac ku p bat tery , the content s of t he m em ory m ay no l ong er be backe d u p so t hat t he data stored in t he BHT m ay be lost.
Chapter 2 Getting Started the BHT and System Menu 35 2.4.1 Replacing the Backup Battery Before proceedi ng to the replacement proc edure below , it is recommended that you sa ve importan t data into the FLASH folder or upload it to the host computer .
36 (4) Pull the lock of the inside co ver to the right and towards you to release it. (5) Pull the right end of the clear insulation shee t up and out of the BHT.
Chapter 2 Getting Started the BHT and System Menu 37 (6) Slide the backup battery cover to the right and take it out. (7) Lift up the backup battery, take its lead wires out of the groove, and disconnect the battery connector as shown below.
38 (8) Connect the connector of a new backup battery with the red lead facing to the left. (9) Route the lead wires inside t he guides through the groove. For easier routing, use a tool whose tip is thin and round. (10) Load the backup battery. (11) Slide the backup battery cover back into place.
Chapter 2 Getting Started the BHT and System Menu 39 (12) Set the clear insulation sheet back into place while threading the battery pull strap through the cutout in the sheet. (13) Set the inside cover so that its lock and pawl become fitted between the printed circuit boards.
40 (14) Push the battery cartridge into the BHT. The end of the battery pull strap should come out from the left edge of the battery cartridge. (15) Set the battery cartridge co ver back into place and return the right and left release buttons to the original position.
Chapter 2 Getting Started the BHT and System Menu 41 2.4.2 Resetting the Dis charge Counter If you replace the backup battery , reset the internal discharge counter in the BhtShell System Properties Menu. For detailed operation, refer to Section 2.5.4, "[3] System Properties Menu, Backup Battery Discharge Counter .
42 2.5 Operating in System Menu 2.5.1 Desktop Upon completion of setting-up 2 (described in Section 2.3.2), the desktop appears on t he touch screen as shown below . Double-tapping icons on the desktop runs the corresponding programs. My Device On the desktop, double-tap My D e v ice .
Chapter 2 Getting Started the BHT and System Menu 43 Recycle Bin On the desktop, double-tap Recycle Bin . The Recycle Bin opens. The Recycle Bin stores files you deleted in the BHT . T o retrieve files stored in the Recycle Bin, select th e file to be retrieved and choose File|Restore .
44 Configuring Proxy Serv er When the Internet Explorer runs, choose V iew |Internet Options to call up the Options window . T ap the Connection tab to display the screen sho wn at left. Make your settings. Messenger On the desktop, double-tap Messenger .
Chapter 2 Getting Started the BHT and System Menu 45 My Documents On the desktop, double-tap My D ocum ent s . The screen sho wn at left appears. With this program, you can browse the file information in the BHT . Remote Desktop Co nnection On the desktop, double-tap Remote Desktop Connection .
46 2.5.2 S tart Menu T ap the button in the bottom left corner of the desktop. The S tart menu appears where you can run programs and make system settings. T erminal On the Star t menu, tap Pr o grams|Communication|T erminal . The screen shown at left appears.
Chapter 2 Getting Started the BHT and System Menu 47 Command Prompt On the Star t menu, tap Pr ograms|Command Prompt . The screen shown at left appears.
48 Backlight Properties On the Control Panel window , double-tap Backlight , and the Backlight Properties window appears. - Backlight function ( * 1) Enable or disable the backlight function. If it is enabled, the backlight comes on when you press any key or tap the touch screen.
Chapter 2 Getting Started the BHT and System Menu 49 BHTSettings On the Control Panel windo w , double-tap BHTSettings , and the BHTSettings window appears. For details, refer to Section 2.5.4. [3] “System Properties Menu." System Properties On the Control Panel window , double-tap System , and the System Properties window appears.
50 Stylus Properties On the Control Panel window , double-tap Styl u s , and the S tylus Properties window appears. Y ou can adjust the double-tap speed. T ap the Calibration tab to display the window shown at left. T ab the Recalibrate to display the screen sho wn at left.
Chapter 2 Getting Started the BHT and System Menu 51 Dialing Properties On the Control Panel window , double-tap Dialing , and the Dialing Properties window appears. Y ou can set up the telephone line. Owner Properties On the Control Panel window , double-tap Ow ne r , and the Owner Properties window appears.
52 V olume & Sounds Properties On the Control Panel windo w , double-tap V olume & Sounds , and the V olume & Sounds properties window appears.
Chapter 2 Getting Started the BHT and System Menu 53 Display Properties On the Control Panel window , double-tap Display , and the Display Properties window appears. T ap the Background tab to display the screen shown at left. Y ou can select wallpaper to be displayed on your desktop.
54 Connection On the Control Panel window , double-tap Network and Dial-up Connection , and the Connection window appears. Double-tap the "Make New Connection" icon starts Wiza rd. Follow the Wizard instructions and set the connection name and type.
Chapter 2 Getting Started the BHT and System Menu 55 Date/Time Properties On the Control Panel window , double-tap Date/T ime , and the Date/T ime Properties windo w appears. Y ou can specify the date, time and time zone. The entry range to th e year is 2003 to 2099.
56 Ta s k b a r On the Star t menu, tap Settings|T askbar . The T askbar and S tart Menu window appears. T ap the General tab to display the screen shown at left. Y ou can customize the taskbar . Run On the Star t menu, tap Run , and the screen shown at lef t appears.
Chapter 2 Getting Started the BHT and System Menu 57 2.5.3 Operating in System Men u On the desktop, double-tap BhtShell . System Menu starts up to display the following screen: T o run the items in System Menu, tap the desired item or press the corresponding numerical key .
58 S tructure of System Menu System Menu Double-tapping the BhtShell shortcut icon on the desktop start s up System Menu. Execute Program Executes a user program you select. (Refer to Section 2.5.4, [ 1 ].) Communication Communicates with the host computer .
Chapter 2 Getting Started the BHT and System Menu 59 Hardware T est T ests a variety of hardware operations. (Refer to Section 2.5.4, [ 4 ].) Explorer Runs Explorer . (Refer to Section 2.5.4, [ 5 ].) System Information Shows the system program version and memory size.
60 2.5.4 Detailed Description of the Functions in System Menu [ 1 ] Execute Program Choosing "1:Execute Program" in System Menu calls up the screen shown at left. With this menu, you can start an application you want. ⇓ T ap the Brow se button.
Chapter 2 Getting Started the BHT and System Menu 61 [ 2 ] Communication Menu Choosing "2:Communication" in System Menu calls up the screen shown at left. [1] Ymodem: Switches to the Ymodem menu where you can set the Ymodem communications parameters and download/upload files.
62 Setting the communications environments T apping button on the Ymodem menu calls up the communications environments setting screen. When using connector interface T o communicate with the host computer via the connector interface port, select "Serial (COM1:)" in Port .
Chapter 2 Getting Started the BHT and System Menu 63 Downloading S pecify a folder where you want to store a do wnloaded file and then tap button , and the BHT wait s for a file to be downloaded. If you download a file hav ing the same name as one already in the same folder , the newly downlo ade d file replaces the old one.
64 If an error occurs during do w nloading If some error occurs during downloading, the BHT beeps three times and shows one of the following screens. Problem The memory is insufficient for storing files to be downloaded. Solution Delete unnecessary files in the memory or decrease t he size of the file to be downloaded.
Chapter 2 Getting Started the BHT and System Menu 65 Problem Downloading has failed. Solution Confirm the communications environment settings and then retry the download. It is also necessary to check the communications environment setup of the host computer .
66 Uploading S pecify a file you want to upload and then tap button , and the BHT waits for a file to be uploaded. ⇓ Upon completion of uploading, the BHT sounds a long beep once and displays the screen shown at left.
Chapter 2 Getting Started the BHT and System Menu 67 If an error occurs during uploading If some error occurs during uploading, one of the following screens will appear and the beeper beeps three times. Problem The file you attempted to upload was opened.
68 Problem T imeout has occurred. Solution Confirm the communications environment settings and communications log, then retry the upload. It is also necessary to check the communications environment setup of the host computer . Problem No file has been correctly selected for uploading.
Chapter 2 Getting Started the BHT and System Menu 69 [2.2] ActiveSync (Infrared) Choosing "2:ActiveSync (Infrared)" on the Communication menu connects the BHT to the host computer via the IrDA interface port. Upon completion of connection, the screen shown at left appears.
70 [2.3] ActiveSync (Serial) Choosing "3:ActiveSync (Serial)" on the Communication menu connects the BHT to t he host computer via the connector interface port.
Chapter 2 Getting Started the BHT and System Menu 71 [2.4] ActiveSync (USB) Choosing "4:ActiveSync (USB)" on the Communication menu connects the BHT to the host computer via the USB interface port. Upon completion of connection, the screen shown at left appears.
72 [2.5] ActiveSync (RF) Choosing "5:ActiveSync (RF)" on the Communication menu connects the BHT to the host computer via the RF interface port. Before proceeding to "Activ eSync (RF)," you need to: - Set up a partnershi p between the host com puter and BHT by running "Acti veSync (Infrared).
Chapter 2 Getting Started the BHT and System Menu 73 Upon completion of connection by ActiveSync, the screen shown at left appears. If connection to the network fails If connection to the network fails, the BHT beeps three times and displays the following screen.
74 [ 3 ] System Properties Menu Choosing "3:System Properties" in System Menu calls up the window shown at left. [1] Barcode: Opens the Barcode menu. [2] Beeper/Vibration: Opens the Beeper/Vibration menu. [3] Control Panel: Opens the Control Panel window.
Chapter 2 Getting Started the BHT and System Menu 75 DECODE LEVEL You may set the decode level. Decreasing the level value increases the bar-code reading efficiency, but the BHT might misread low-quality bar codes (split or stained).
76 [3.2] Beeper/Vibration Double-tap the "Beeper/V ibration", and the Beeper/Vibration property appears. On this menu, you can adjust the beeper volume and s witch the beeper and vibrator .
Chapter 2 Getting Started the BHT and System Menu 77 [3.3] Control Panel Double-tap the "Control Panel", and the Control Panel window appears. With this menu, you can set up the basic Windows operating environment. For details, refer to Section 2.
78 Initializing the memory excluding the Registry Y ou can initialize the memory excluding the Registry and files stored in the FLASH folder . Initializing procedure (1) Tap the Initialize tab and select the RAM radio button. (2) Tap the Initialize button.
Chapter 2 Getting Started the BHT and System Menu 79 Initializing the memory including the Registry Y ou can initialize the memory including the Registry but excluding files stored in the FLASH folder . Initializing procedure (1) Tap the Initialize tab and select the RAM radio button.
80 Initializing the FLASH folder Y ou can erase all information stored in the FLASH folder and let the folder revert to the initial state. Initializing procedure (1) Tap the Initialize tab and select the FLASH radio button. (2) Tap the Initialize button.
Chapter 2 Getting Started the BHT and System Menu 81 Running Scandisk thr ough the FLASH folder If the power to the BHT is shut down when the FLASH folder is being accessed, some broken file fragments may remain in the FLASH folder so that the free memory space will be decreased.
82 [3.5] Power Management Double-tap the "Power Management", and the Power Management property appears. Y ou can set the automatic power-of f tim er , the standby timer , and CPU clock. Automatic Power-Of f T ime: Battery Power: For the BHT being out of the CU, set the automatic power-off timer .
Chapter 2 Getting Started the BHT and System Menu 83 [3.6] Key Double-tap the "Key", and the Key property appears. Y ou can define the functions of the following keys: - SF/ALP (SF) key - M1.
84 Defining the M1, M2, M3 (left-hand trigger sw itch), M4 (right-hand trigger sw itch), and M5* keys * M5 key available on the grip style BHT Choose the MAGIC Full-press tab on the Key definition menu to display the screen shown at left.
Chapter 2 Getting Started the BHT and System Menu 85 If you define the M4 key as a backli ght function on/of f key , pressi ng the M4 key activates or deactivates the bac klight function. Note that the b acklight function on/o f f key c an be assi gned only to a ny one of M1 through M5 * keys and halfway pressed M3 through M5 * keys.
86 [3.7] Status Display Double-tap the "S tatus Display", and the S tatus Display property appears. Y ou can display or hide the following status indicators in the task tray: BATTERY: Batter.
Chapter 2 Getting Started the BHT and System Menu 87 Displaying the wireless module version and opening/closing the RF device T apping the Info tab on the NIC Control menu displays the screen shown at left.
88 Setting the ESSID T apping the ID tab on the NIC Control menu displays the screen shown at left. Y ou can specify an ESSID (Extended Service Set ID) to be used on the communications network. For details about the ESSID, refer to Chapter 3, Section 3.
Chapter 2 Getting Started the BHT and System Menu 89 Setting the WEP keys (Authentication: Open) (40-bit WEP) T apping the WEP tab on the NIC Control menu displays any of th e following three types of screens according to the authentication type.
90 Displaying the current communications link status T apping the Link tab on the NIC Control menu displays the screen shown at left where the current communications link st atus appears in real-time. Associated Access Point: Displays the MAC address assigned to the wireles s interface of the associated access point.
Chapter 2 Getting Started the BHT and System Menu 91 T esting with Ping T apping the Ping tab on the NIC Control menu displays the screen shown at left. Dest IP: S pecify the IP address of a host computer that you want to ping. Data size: S pecify the data size of an echo request.
92 Ping Echo Request Send T iming T wo types of echo request send timings are available: T ype 1 and T ype 2. The default is T ype 2. • Type1 After sending an echo request, Ping will wait for the period specified by Interval and then send an echo request again.
Chapter 2 Getting Started the BHT and System Menu 93 Backup Battery Discharge Counter On the System Properties Menu, pressing the 0 key with the SF/ALP ( SF ) key held down calls up the screen shown at left. This screen displays the discharge count of the backup battery .
94 [ 4 ] Test Menu Choosing "4:T est" in Sy stem Menu calls up the screen shown at left. [1] BARCODE: Select the bar-code reading test. [2] BEEPER: Select the bee per scale test. [3] AGING: Select the aging test. [4] COM: Select the communications test.
Chapter 2 Getting Started the BHT and System Menu 95 [4.1] Bar-code reading test Selecting "1: BARCODE" on the Hard T est menu calls up the screen shown at left. Actually read bar codes with the BHT and check that the barcode data read matches ones displayed on the LCD.
96 [4.2] Beeper scale test Selecting "2:BEEPER" on t he Hard T est menu calls up the screen shown at left and sounds the beeper at three octaves listed below . Upon completion of this test, the BHT automatically returns to the Hard T est menu.
Chapter 2 Getting Started the BHT and System Menu 97 [4.4] Communications test In System Menu, you can test the IrDA interface port and USB interface port.
98 Testing the IrDA interface port Selecting the "1:OPTICAL" on the COM menu calls up the screen shown at left. At the slave BHT to be tested, select the "1:SLA VE" and at the maste r BHT , select th e "2:MASTER." Then press the ENT key on each BHT .
Chapter 2 Getting Started the BHT and System Menu 99 If the IrDA interface test ends abnormally : If the test ends due to a timeout error , the tested slave BHT beeps three times and displays the screen as shown at left. This sample screen shows that an error has occurred at 2400 bps.
100 Testing the USB interface port Selecting the "2:USB" on the COM menu calls up the screen shown at left and start s connecting with the host computer using ActiveSync. For the configuration of the host computer and details about ActiveSync, refer to Chapter 3, Section 3.
Chapter 2 Getting Started the BHT and System Menu 101 To terminate the USB interface test There are two ways to terminate the USB interface test--"Disconnect the USB interface cable" and "Disconnect the link with the button in the task tray (as described below).
102 [4.5] LCD and indicator LED tests Selecting "5:DISPLA Y" on the Hard T est menu calls up the test pattern shown at left on the LCD and turns on the indicator LED in blue. Each time the ENT key is pressed, the screen shifts to the next test pattern.
Chapter 2 Getting Started the BHT and System Menu 103 The checker pattern is reversed. C/BS (BS) key ⇑ ⇓ ENT key The gray screen appears with a one-dot wide white outline.
104 The gradation pattern appears. Press the ENT key , and the BHT returns to the Hard T est menu..
Chapter 2 Getting Started the BHT and System Menu 105 [4.6] Key entry and vibrator test Selecting "6:KEY VIBRA TION" on the Hard T est menu calls up the screen shown at left and makes the BHT ready for entry from the keypad. Pressing individual keys displays the identifier letters in the positions pre-assigned to those keys on the LCD.
106 [ 5 ] Explorer Choosing "5:Explorer" in System Menu calls up the screen shown at left. [ 6 ] System Information Choosing "6:V ersion" in System Menu calls up the screen sho wn at left.
Chapter 2 Getting Started the BHT and System Menu 107 2.6 W ireless Zer o Configuration (WZC) The screen on the left displays if a wireless local area network (wireless LAN) environment has not yet been established following purchase of the BHT unit.
108 IP Information T apping the IP Information tab on the WZC Menu displays the screen shown at left. Internet Protocol (TCP/IP) settings information displays at this menu. Renew: Updates with the latest information. Details: Displays detailed information.
Chapter 2 Getting Started the BHT and System Menu 109 Wir eless Information Wireless Properties T apping the Wireless Information tab on the WZC Menu displays the screen shown at left. The SSID list for which a search was performed automatically by the BHT displays.
11 0 This key is provided automatically: Select this check box to automatically obtain the network key . Enable 802.1X authentication: Select this check box to enable 802.
Chapter 2 Getting Started the BHT and System Menu 111 • Settings when PEAP , TLS Selected for EAP T y pe T apping the Properties… button on the Wireless Properties window displays the screen shown at left. Displays the User Certificate issuance information.
11 2 Advanced Wireless Settings T ap the Ad vanced… button from the Wireless Information tab to display the screen on the left. Use Windows to configure my wireless settings: Select this check box to automatically perform wireless network settings at Windows CE.
11 3 Chapter 3 Communications Operations of the BHT -202B-CE/202BW -CE Describes the communications operations of the BHT—the spread spectrum communication (BHT -202BW-CE only), infrared commun icat.
11 4 3.1 Spr ead Spectrum Communication The BHT-202BW-CE supports spread spectrum communication. 3.1.1 Notes for W ireless Operations • If there are too many communications errors, first make sure that the BHT -202BW-CE points directly at an access point because the 2.
Chapter 3 Communications Oper ations of BHT -202B-CE/202BW -CE 11 5 3.1.2 RF-Related Parameters Wireless communication between the BHT terminals and access point s that are connected to each other by a wireless LAN are command-controlled by user programs.
11 6 TRANSMIT KEY Y ou need to use the TRANSMIT KEY in order to choose and activate any one of the WEP KEY1 through WEP KEY4 already defined. If the size of the WEP KEY specified as a TRANSMIT KEY for the BHT is dif ferent from that for the access point, no communication is pos sible.
Chapter 3 Communications Oper ations of BHT -202B-CE/202BW -CE 11 7 3.2 Infrared Communication The BHT has an integrated infrared (IR) communications device which enables wireless transfer of programs and data between the BHT and the host computer and between the BHTs, instead of the conventional wire transfer.
11 8 3.3 Connector interface specification The BHT-202BW-CE is equipped with a USB interface for interfacing with the host PC, and with a connector interface for communicating with the host PC.
Chapter 3 Communications Oper ations of BHT -202B-CE/202BW -CE 11 9 (3)-1 Interface circuit （ USB ） (3)-2 Interface circuit （ RS-232C ） Output circuit Input circuit TxD, R TS RxD, CTS Signal Level Item Min.
120 3.4 Basic Communications Specifications and Ymodem 3.4.1 Basic Communications Sp ecifications Listed below are the communications specifications when the BHT exchanges data with a host computer through the CU-200 (IrDA interface) or the connector interface*.
Chapter 3 Communications Oper ations of BHT -202B-CE/202BW -CE 121 Transmission Code and Bit Order All characters should be coded to 7 or 8-bit code fo r data transmission.
122 3.4.2 Using Ymodem In System Menu and user programs, the BHT can use the Ymodem protocol with the following communications parameters: Port IrDA interface Connector interface Transmission Speed 24.
Chapter 3 Communications Oper ations of BHT -202B-CE/202BW -CE 123 3.5 ActiveSync With Microsoft ActiveSync, the BHT can exchange data with the host computer connected by IrDA, USB, connector interface , or spread spectrum communication (BHT -202BW-CE).
124 Setting up ActiveSync 3.7 Make ActiveSync connection settings according to the procedure below . S tart the inst alled ActiveSync 3.7, and the screen shown at left appears.
Chapter 3 Communications Oper ations of BHT -202B-CE/202BW -CE 125 3.5.2 Connection Using ActiveSync When connected by IrDA, USB, or connec tor inter fac e IrDA communication Arrange the BHT and host computer with their IrDA ports facing directly each other as shown below .
126 Connector interface communication Connect the BHT (connector interface port) to the host computer (RS-232C interface) by usin g a connector interface cable as shown below . For ActiveSync operating procedures on the BHT , refer to Chapter 2, Section 2.
Chapter 3 Communications Oper ations of BHT -202B-CE/202BW -CE 127 Setting up a p artnership Upon completion of connection between the host computer and BHT , the host computer displays the screen shown at left. On this screen, set up a partnership betw een the host computer and BHT .
128 Click Finish to complete the setup and return to Windows. The partnership between the BHT and host computer has been set up. For instructions on how to use ActiveSync, refer to its Help on the host computer .
Chapter 3 Communications Oper ations of BHT -202B-CE/202BW -CE 129.
130 Chapter 4 Err or Messages This chapter lists the error messages which will appear on the LCD if some error occurs in the BHT. 4.1 System Errors .......................................................................................................
Chapter 4 Error Messages 131 4.1 System Err ors If some error occurs when the power is turned on or during program ex ecution, one of the following error messages will appear on the LCD. System Program error Problem A System Program error has occurred.
132 Shut dow n due to low battery Problem When the power is turned on or off or during execution o f applications, the battery output level has lowered so that the BHT no longer operates. If lower battery is detected, the BHT beeps five times (for 0.
Chapter 4 Error Messages 133.
134 This chapter describes the handling procedure of the communication unit CU-200, the interfacing with the host PC, and the charging of the rechargeable battery cartridge. 5.1 Functions of the CU-200 .................................................
Chapter 5 Handling the C U-200 (Option) 135 5.1 Functions of the CU-200 The optical communication unit CU-200 series is available in t wo models: CU-201 and CU-221. The CU-200 series has the following functions: (1) Data exchange function The CU-201/221 exchanges data and programs between the BHT and the host PC.
136 5.2 Components and Functions St atus ind i cators POWER LED (green) Lights when the power is applied to the CU. DA TA Communications LED (gr een) Lights when the BHT is communicating with the host PC. IrD A interface port Used to exchange data optically with the BHT .
Chapter 5 Handling the C U-200 (Option) 137 5.3 Applying Power to the CU-200 CU-201: The CU-201 should be powered from a wall socket via the dedicated AC adapter . Connec t the outlet plug of the AC adapter to the power inlet connector of the CU-201, then plug the other end into a wall socket.
138 • If you are not u sing th e CU for a long time, be sure to unp lu g the AC adapter from the wall socket for safety . Failure to do so could result in a fire. • When caring fo r the CU, unplug the AC adapt er from the wall socket for safety . Failure to do so coul d result in an electrical shock.
Chapter 5 Handling the C U-200 (Option) 139 5.4 Communicating with the Host PC 5.4.1 Setting the Transmi ssion Speed of the CU-200 CU-201: Set the transmission speed to the same value as that of the BHT and host PC, by using the DIP switch. CU-221: The transmission speed is a utomatically determined by the host PC.
140 5.4.2 Interface Cable Connection (1) Unplug the AC adapter of the CU-200 from the wall socket. (2) Make sure that the host PC is turned off. (3) CU-201: Connect the RS-232C interfa ce cable to the interface port of the CU-201. CU-221: Connect the USB interface c able to the interface port of the CU-221.
Chapter 5 Handling the C U-200 (Option) 141 5.4.3 Interfacing with the Host PC This section describes how to start communication with the host PC fro m System Menu. The same may apply when you use a user program. (1) Turn the host PC on to run Windows.
142 5.5 Charging the Rechargeable Battery Cartridge (using the CU-200) Y ou can charge a rechargeable battery cartridge loaded in the BHT . Be sure to turn the BHT off before starting charging.
Chapter 5 Handling the C U-200 (Option) 143 Charging Operation and LED Indication Operator's Action CU-200 St at us Charge LED on the BHT On standby ⇓ Place the BHT on the CU-200. ⇓ Chargi ng ⇓ After approx. 3 hours (approx. 5.5 hours*) when the CU-201/221 is powered from the AC adapter After approx.
144 5.6 Interface Specifications [ 1 ] Interface Connector and Pin Assignment CU-201 The CU-201 has an RS-232C interface port (Dsub-9P). RS-232C interface port (Dsub-9P) on the CU -201 Pin No.
Chapter 5 Handling the C U-200 (Option) 145 [ 2 ] Interface Cable Connection CU-201 As illustrated below , connect the CU-201 (on which the BHT is put) to a host PC with a cross-mode cable.
146 Appendix A. S pecifications ................................................................................................................. .............................147 A.1 BHT -202B-CE/202BW-CE ..............................................
Appendices 147 Appendix A. Specifications A.1 BHT-202B-CE/202BW-CE [ 1 ] Product Specifications Power Source Main power Rechargeable lithium-ion battery cartridge (3.7 VDC) Dimensions (W) x (L) x (H) 90 x 186 x 44 mm (3.5 x 7.3 x 1.7 i nches) Weight Regular style B HT Grip style BHT Approx.
148 [ 2 ] Bar Code Specifications (1) Available Bar Code Types Bar code type Bar dimensions Readable magnificatio n Universal product codes EAN-13 EAN-8 UPC-A UPC-E EAN-13 with add-on EAN-8 with add-on UPC-A with ad d-on UPC-E with ad d-on 2-digits add-on 5-digits add-on 0.
Appendices 149 (3) Bar Code Label Size Recommended width: 10 mm min. (0.39 inch min.) Depth of field (Distance from bar codes to the reading window) Length of labels (including margins) Length: 700 mm (27.56 inches) 400 mm max. (15.75 inches max.) (Minimum narrow bar width: 0.
150 Connector Interface Specification: USB1.1, Full-speed compliant, RS-232C interface Connector: TCX3171 HOSIDEN Pin assignment: See below. Pin No Signal name Data direction 1 GND − 2 D+ (USB) Inpu.
Appendices 151 A.2 CU-200 [ 1 ] Product Specifications CU-201 CU-221 Power Source 100 to 240 VAC, 50/60 Hz, 0.2 A (5 VDC: Use AC adapter) Supplied via the USB cable* Power Consumption (AC adapter output) 5 VDC, 1500 mA 5 VDC, 500 mA Dimensions (W) x (L) x (H) 114 x 140 x 87 mm (4.
152 [ 3 ] Interface Specifications CU-201 RS-232C interface port (Dsub-9P) on the CU -201 Pin No. Signal Functions Signal Input/Output CU-201 External device 2 RD Receive data ← 3 SD Send data → 4.
Appendices 153 Appendix B. Loading an Optional Compact Flash Card Load an optional Compact Flash card to the BHT using the following procedure. (1) Turn the BHT upside down. (2) Slide the right and left release buttons in the direction of t he arrows to remove the battery cartridge cover .
154 (4) Pull the lock of the inside co ver to the right and towards you to release it. (5) Insert a Compact Flash card into the slot with the connector facing the slot and with the top facing down.
Appendices 155 T o remove the Compact Flash card, press the card release button provided at the left of the card as shown below . (6) Set the inside cover so that its lock and pawl become fitted between the printed circuit boards.
156 (7) Push the battery cartridge into the BHT . The end of the battery pull strap should co me out from the left edge of the battery cartridge. (8) Set the battery cartridge cover back into place and return the right and left release buttons to the original position.
Appendices 157 Appendix C. Quality Assurance Standards C.1 Interface Cables With the interface cables described in this section, DENSO WAVE has run the quality assurance test conforming to the EMC Directive for the BHT-202B-CE/202BW-CE and CU-200. Any connectors other than those specified here are not acceptable.
.
BHT -202B-CE/202BW - CE User's Manual First Edition, June 2006 DENSO W A VE INCORPORA TED The purpose of this manual is to provide accurate information in the handling and operating of the BHT -202B-CE/202BW-CE.
Ein wichtiger Punkt beim Kauf des Geräts Denso BHT-202B-CE/202BW-CE (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Denso BHT-202B-CE/202BW-CE noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Denso BHT-202B-CE/202BW-CE - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Denso BHT-202B-CE/202BW-CE reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Denso BHT-202B-CE/202BW-CE erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Denso BHT-202B-CE/202BW-CE besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Denso BHT-202B-CE/202BW-CE verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Denso BHT-202B-CE/202BW-CE. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Denso BHT-202B-CE/202BW-CE gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
