Benutzeranleitung / Produktwartung 36-560 w/stand) des Produzenten Delta
Zur Seite of 24
INSTRUCTION MANUAL 10" T able Saw (Model 36-550) (Model 36-560 w/stand) P ART NO. 904817 - 02-19-02 Copyright © 2002 Delta Machinery ESP AÑOL: PÁGINA 25 T o learn more about DEL T A MACHINER Y visit our website at: www .
2 GENERAL SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedur es ar e not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the pr oduct. Using the machine with respect and caution will considerably lessen the possibility of personal injury .
ADDITIONAL SAFETY RULES FOR T ABLE SA W 3 WARNING: F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . 1. DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions.
4 POWER CONNECTIONS A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wir e and should be protected with a 20 Amp time lag fuse.
Use proper extension cor ds. Make sur e your extension cord is in good condition and is a 3-wir e extension cor d which has a 3-prong gr ounding type plug and matching r eceptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the curr ent of the machine.
6 Fig. 3 6 - Rip Fence 7 - Wr enches for Blade Changing 8 - M8 Hex Nut for Rip Fence 9 - Locking Handle for Rip Fence 10 - Fence Rail 11 - Blade Raising and Lowering Handwheel 12 - M6 x 12mm Flat Head.
7 Fig. 4 FOR MODEL 36-560 ONL Y 49 - Leg (4) 50 - 3/8” Flat W asher for Mounting Saw to Stand & for Assembling Stand (24) 51 - Foot (4) 52 - M8 Hex Nut for Mounting Saw to Stand & for Assemb.
8 ASSEMBL Y ASSEMBLING BLADE RAISING AND LOWERING HANDWHEEL 1. Insert M6 x 55mm cheese head screw (14) Fig. 3, through handle (E) Fig. 5 and assemble handle (E) to handwheel (A) by threading scr ew (D) Fig. 5 clockwise into handwheel. 2. Fig. 6, illustrates the handle (E) assembled to handwheel (A).
9 ASSEMBLING BLADE GUARD AND SPLITTER ASSEMBL Y 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. IMPORT ANT : THE BLADE GUARD AND SPLITTER ASSEMBL Y MUST BE PROPERL Y ALIGNED TO THE SAW BLADE IN ORDER TO PREVENT KICKBACK. 3. Position the blade 90 degrees to the table and lock in place.
10 8. Assemble splitter (H) Fig. 14, to splitter support bracket (B) as shown using M6 x 20mm hex head screw (L), 1/4" external tooth washer , and 1/4" flat washer . 9. Fasten splitter (H) Fig. 15, to splitter support bracket using 1/4" flat washer , 1/4" exter nal tooth lockwasher and M6 wing nut (M).
11 ASSEMBLING EXTENSION WING 1. Assemble extension wing (A) Fig. 18, to the saw table using three 1/4-20 x 5/8” hex head scr ews (B), 1/4" lockwashers (C), and 1/4" flat washers (D).
12 ASSEMBLING RIP FENCE 1. Thread an M8 hex nut (A) Fig. 22, appr oximately halfway onto stud of handle (B). 2. Thread handle (B) Fig. 22, into tapped hole (C) in fence cam (D). Tighten hex nut (A) Fig. 23, against cam (D). 3. Lower rip fence onto table as shown in Fig.
13 ASSEMBLING MITER GAGE HOLDER 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Assemble spring clip (E) Fig. 26, to the miter gage holder (A) as shown using a M4x10mm pan head screw (F), 3/16" lockwasher and M4 hex nut. NOTE: Hex nut (G) Fig. 27, will fit into the recess at the back of the miter gage holder (A) to keep spring clip (E) Fig.
14 ASSEMBLING OUTFEED SUPPOR T 1. Loosely fasten brackets (A) Fig. 31, to the bottom left side of the saw table as shown, using two M6x15mm hex head screws (B) and M6.1 lockwashers (C). Assemble two remaining brackets to the bottom right side of saw table in the same manner .
15 ASSEMBLING ST AND (FOR MODEL 36-560 ONL Y) 1. Assemble the stand as shown in Fig. 36, using 16 carriage bolts, flat washers and hex nuts. Do not completely tighten the hardwar e at this time. Letters ar e stamped on the stand brackets for ease in assembly .
16 OPERA TING CONTROLS AND ADJUSTMENTS ST AR TING AND STOPPING SA W 1. The on/off switch is located underneath the switch shield (A) Fig. 41. T o tur n the saw “ON” , move switch trigger (B) to the up position. 2. T o tur n the saw “OFF” , push down on switch shield (A) Fig.
17 BLADE TIL TING CONTROL T o tilt the saw blade, loosen blade tilting lock handle (A) Fig. 45, move handwheel (B) until the blade is at the desired angle and tighten lock handle (A).
18 RIP FENCE OPERA TION AND ADJUSTMENTS 1. T o move the rip fence (A) Fig. 48, along the table, lift up fence locking lever (B), slide the fence to the desired location on the table and push down fence locking lever (B) to lock the fence in position. 2.
19 ADJUSTING BLADE P ARALLEL TO MITER GAGE SLOTS The blade was adjusted parallel to the miter gage slots at the factory . In or der to insure accurate cuts and help prevent kickback when cutting, this adjustment should be rechecked and if necessary , readjusted as follows: 1.
20 OPERA TION Common sawing operations include ripping and cross-cutting plus a few other standar d operations of a fundamental nature. As with all power tools, ther e is a certain amount of hazar d involved with the operation and use of the tool.
21 If the ripped work is less than 4 inches wide, a push stick should always be used to complete the feed, as shown in Fig. 124. The push stick can easily be made from scrap material as explained in the section “CONSTRUCTING A PUSH STICK.
22 CONSTRUCTING A FEA THERBOARD Fig. 60, illustrates dimensions for making a typical featherboard. The material which the featherboar d is constructed of, should be a straight piece of wood that is free of knots and cracks. Featherboar ds ar e used to keep the work in contact with the fence and table and help prevent kickbacks.
23 CONSTRUCTING A PUSH STICK When ripping work less than 4 inches wide, a push stick should be used to complete the feed and could easily be made from scrap material by following the pattern shown in Fig. 62. Fig. 62 PUSH STICK MAKE FROM 1/2” OR 3/4” WOOD OR THICKNESS LESS THAN WIDTH OF MA T’L.
24 T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in.
Ein wichtiger Punkt beim Kauf des Geräts Delta 36-560 w/stand) (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Delta 36-560 w/stand) noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Delta 36-560 w/stand) - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Delta 36-560 w/stand) reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Delta 36-560 w/stand) erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Delta 36-560 w/stand) besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Delta 36-560 w/stand) verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Delta 36-560 w/stand). Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Delta 36-560 w/stand) gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
