Benutzeranleitung / Produktwartung 26007 des Produzenten Dell
Zur Seite of 52
Dell™E157FPTTouchScreenMonitorContents Information in this document is subject to change without notice. © 2007DellInc.Allrightsreserved. Reproduction in any manner whatsoever without the written permission of Dell Inc.
Back to Contents Page About Your Monitor Dell™E157FPTTouchScreenMonitorContents Front View Back View Side View Bottom view Specifications Caring for Your Monitor Front View 1. Menu button - Enters/exits the OSD menu.
1. Cable holder 2. Monitor stand 3. Tilt - adjust knob 4. Mounting holes for optional Magnetic Stripe Reader (MSR) device 5. Cable cover 6.
1. Video connector 2. Audio connector 3. Power status LED indicator 4. Touch status LED indicator 5. Serial connector 6. USB connector 7. AC power Side View To adjust monitor angle: 1. Loosen tilt - adjust knob.
General Flat Panel The following table shows physical and optical properties of the monitor's display panel. Resolution The following table shows the scan rate and pixel resolution capabilities of the monitor's display.
Environmental The following table shows tolerable ambient environments while on (operating) and while off (non - operating). Power Management Modes During normal operation, the monitor's LED light is green . The LED indicates altered LED colors when monitor operates in different modes.
Pin Assignments - 15 - pin D - sub connector Plug and Play Capability You can install the display in any Plug and Play - compatible system. The display automatically provides the computer syst.
Back to Contents Page Appendix Dell™E157FPTTouchScreenMonitorContents Warranty Information CAUTION:General Safety Instructions CAUTION: Monitor Safety Instructions Contacting Dell Regulatory Notices Your Monitor Setup Guide Warranty Information U.
contract you purchased. Dell is not obligated to provide service or support you purchase through a third party and not Dell. 9. Limitation of Liability.
l The limited warranty for Power Adapters purchased independent of a system is one year. Power Adapters purchased with a system are covered by the system limited warranty. l Your PERC 5 battery may provide up to 72 hours of controller cache memory backup power when new.
During the remaining years: For the remaining period of the limited warranty, we will replace any defective part with new or refurbished parts, if we agree that it needs to be replaced.
l Ship back all products you are seeking to return to Dell. At Dell's discretion, credit for partial returns may be less than invoice or individual component prices due to bundled or promotional pricing and any unadvertised discounts or concessions.
l If your equipment does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service center.
Connecting the AC Plug Adapter (Japan Only) 1. Connect the metal ground connector to the grounding source on the outlet: a. Loosen the grounding source. b. Slide the metal ground connector behind the grounding source, and then tighten the grounding source.
1. Save and close any open files, exit any open programs, and shut down the computer. 2. Disconnect the computer or monitor AC adapter from the electrical outlet, and then, if possible, disconnect the AC adapter from the computer or monitor.
Country (City) International Access Code Country Code City Code Service Type Area Codes, Local Numbers, and Toll - Free Numbers Web and E - mail Address Anguilla Online Support www.
Bermuda Online Support la - techsupport@dell.com Technical Support, Customer Service, Sales 1- 877 - 890 - 0751 Bolivia Online Support www.dell.com/bo la - techsupport@dell.com Technical Support, Customer Service, Sales toll - free:800 - 10 - 0238 Brazil International Access Code: 00 Country Code: 55 City Code: 51 Online Support www.
Large Corporate Accounts Key Accounts toll - free:8008582628 Large Corporate Accounts North toll - free:8008582999 Large Corporate Accounts North Government and Education toll - f.
France (Paris) (Montpellier) International Access Code: 00 Country Code: 33 City Codes: (1) (4) Customer Service 0825823833 Switchboard 0825004700 Switchboard (calls from outside of France.
India Phone Numbers 080 - 25068032 or 080 - 25068034 or your city STD code + 60003355 or toll - free:18004258045 Gold Support Only E- mail eec_ap@dell.com Phone Numbers 080 - 25068033 or your city STD code + 60003355 or toll - free:1 - 800 - 425 - 9045 XPS Support Only E- mail Indiaxps_AP@dell.
Japan (Kawasaki) International Access Code: 001 Country Code: 81 City Code: 44 Technical Support outside of Japan – Dimension and Inspiron 81 - 44 - 520 - 1435 Technical Support – Dell Precision, .
Main or 001 - 800 - 888 - 3355 or 001 - 866 - 851 - 1754 Montserrat Online Support la - techsupport@dell.com Technical Support, Customer Service, Sales toll - free:1 - 866 - 278 - 6822 Netherlands Antilles Online Support la - techsupport@dell.
Customer Service and Sales 1- 877 - 537 - 3355 St. Kitts and Nevis Online Support www.dell.com/kn la - techsupport@dell.com Technical Support, Customer Service, Sales toll - free:1 - 866 - 540 - 3355 St. Lucia Online Support www.dell.com/lc la - techsupport@dell.
City Code: 8 Technical Support Fax 0859005594 Sales 0858770581 Switzerland (Geneva) International Access Code: 00 Country Code: 41 City Code: 22 Online Support support.
Regulatory Notices FCC Notice (U.S. Only) FCC Class B This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer's instruction manual, may cause interference with radio and television reception.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.
Back to Contents Page Setting Up Your Monitor Dell™E157FPTTouchScreenMonitorContents Connecting Your Monitor Using the OSD On - Screen Menu/Display (OSD) Special OSD Functions OSD Warning Messages Setting the Optimal Resolution Connecting Your Monitor 1.
7. Replace the cable cover. 8. Plug the power cables of your computer and your display into a nearby outlet. Your monitor is equipped with an automatic power supply for a voltage range from 100 to 240 Volt at a frequency of 50/60 Hz. Be sure that your local power is within the supported range.
Accessing the Menu System 1. With the menu off, press the 'MENU' button to open the OSD system and display the main features menu. Function Adjustment Method Auto Adjustment While the OSD menu is not showing, use this button to activate automatic setup and adjustment.
The OSD menu will open with the Contrast function selected. 2. Press the - and + buttons to move the OSD highlight cursor to other function icons. As you move from one icon to another, the function name appears, to reflect the function or group of functions (sub - menus) represented by that icon.
V- POSITION H- POSITION The H - POSITION function moves the picture left or right in relation to the monitor bezel. Pressing "+" will move the picture right. Pressing " - " will move the picture left. Minimum is 0.
COLOR TEMP COLOR TEMP USER The COLOR TEMP USER function is one of the available COLOR TEMP choices (see above). It allows individual intensity adjustment of the three primary colors (red, blue, green). This choice is recommended only for advanced users.
SHARPNESS PHASE The PHASE function allows for manual fine adjustment of screen interference. This function is recommended only for advanced users.
OSD H - POSITION OSD V - POSITION The OSD V - POSITION function moves the OSD Menu window up or down in relation to the monitor bezel. Pressing "+" will move the OSD Menu up. Pressing " - " will move the OSD Menu down.
Special OSD Functions l OSD LOCK and UNLOCK l POWER LOCK and UNLOCK l Automatic Save AUTO ADJUST Pressing "Select" will execute the function. Auto Adjustment will take only a few seconds. The OSD Menu will automatically disappear after adjustment is complete.
OSD LOCK and UNLOCK Operation of the OSD Menu may be disabled, thereby preventing unauthorized personnel from modifying any OSD adjustments. To "Lock" (disable) the OSD: 1. Press "Menu" and "+" buttons at the same time.
Automatic Save With the OSD open, if you make an adjustment and then either proceed to another menu or exit the OSD, the monitor automatically saves any adjustments you have made. If you make an adjustment and then wait for the OSD to disappear the adjustment will also be saved.
Back to Contents Page Solving Problems Dell™E157FPTTouchScreenMonitorContents General Problems Touch screen Problems General Problems Touch screen Problems Back to Contents Page Problem Suggestion The monitor does not respond after you turn on the system.
Dell™E157FPTTouchScreenMonitorUser'sGuide Information in this document is subject to change without notice. © 2006DellInc.Allrightsreserved. Reproduction in any manner whatsoever without the written permission of Dell Inc.
Back to Contents Page Using the Touch Screen Software Dell™E157FPTTouchScreenMonitorContents About Your Touch Screen Software Installing Touch Screen Software .
7. Click Next . 8. Review and accept the License Agreement. The driver files are installed. Following installation, the Setup Complete screen appears. 9. To calibrate the monitor, select Calibrate Dell Touch Screen monitors , click Finish .
5. Review and accept the License Agreement. The program will appear to proceed as a single/multiple serial controller installation but USB files will also install. The driver files will install. When the Setup Complete screen appears, you may choose to run calibration (the Video Alignment program, EloVA) immediately or wait until later.
2. Locate the Dell entry, then click Change . The Dell Touchscreen Setup dialog appears. 3. Select Install Serial Touchscreen Drivers , click Next . Adding USB Controllers If there are Dell USB devices already installed, plug the USB cable from the touchmonitor into the computer and run EloVA to calibrate the touchmonitors.
3. Locate the Dell entry, then click Remove . 4. Click Yes to confirm removal. You may see the following message when the Uninstall is complete: Some elements could not be removed. You should manually remove items related to the application. This is normal, as several files remain in use until you restart the computer.
2. Select the General Tab, then click Align . 3. A target appears on the screen. Touch the calibration target firmly and precisely with your fingertip. Be careful to keep your other fingers away from the touch screen as you touch the target. 4.
Mouse button emulation mode Place the right - click tool on your desktop enabling you to utilize right - click functionality using the touch screen. Click on Touch Click on Touch sends a mouse down/up message at the point of touch on the touch screen.
l Show tool tray utility activates the Tool Tray utility in the Windows Task Bar. See Tool Tray for a complete description of this feature Sound The Sound tab sends a single - frequency tone or "Beep" to the system speaker each time a valid touch occurs.
Screen Information l Windows Monitor Number lists the monitor that corresponds to the "Windows Monitor" from the Windows Display Properties control panel. l Touch screen Type: IntelliTouch. l Installed On indicates USB or lists the Windows COM port that a serial touch screen is installed on.
Disable/Enable touch Disable Touch stops touch information from reaching Windows for this touch screen. This feature may also be activated from the Tool Tray utility. Disabling touch has no effect on the operation of the standard mouse. Show right mouse button tool Show right mouse button tool launches this feature for this monitor.
Typically, a right button action will activate a new dialog box for some function similar to mouse right button click. When that dialog box is touched, or any other touch on the touch monitor is made, this touch will be a left button event. Simultaneously, the mouse button shading in the RMBT will toggle back to the left button.
When disabled through the Tool Tray, touches made on the touch screen are not buffered by the driver, and will not be sent from the driver to MouClass after the touch screen is re - enabled. After the touch screen has been disabled, the state of this segment of the Tool Tray menu changes from "Disable" to "Enable.
Configurable parameters are: l Cursor Acceleration scale. This scale can be set from a value of 0 - 10 where, 1 corresponds to no acceleration. l Edge acceleration rectangle bounds dimensions. l Edge acceleration rectangle bounds position.
Ein wichtiger Punkt beim Kauf des Geräts Dell 26007 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Dell 26007 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Dell 26007 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Dell 26007 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Dell 26007 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Dell 26007 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Dell 26007 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Dell 26007. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Dell 26007 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
