Benutzeranleitung / Produktwartung 6650-LC des Produzenten 3M
Zur Seite of 28
Mar ch 2005 78-8135-4385-3-A 3 LC Hot Melt Fiber Optic Connectors Installation.
2 78-8135-4385-3-A Contents 1.0 Safety and Helpful Hints ................................................................................................................3 Hot Melt Oven Safety Information ...............................................
78-8135-4385-3-A 3 1.0 Safety and Helpful Hints Use reagent-grade isopropyl alcohol that is 99% pure to clean the fibers and other components. When terminating connectors on any cable containing grease, ensure that all grease is wiped a way and the buf fer , coating and fiber are thoroughly cleaned with isopropyl alcohol.
4 78-8135-4385-3-A 2.0 3M ™ LC Expansion 6650-LC Kit Contents A A A A C B D E F H I B 1 G A. LC Hot Melt Connector Holder (4) B. LC Polishing Jig Assembly with W eight B 1 Spare Polishing Jig C. LC Crimp T ool D. LC Adapter for V iew Scope E. Heat Shrink Fixture F .
78-8135-4385-3-A 5 3.0 3M ™ LC Connectors 3.1 The Behind The W all (BTW) LC is used for simplex 900 micron applications. The connector contains (A) dust cap, (B) connector , and (C) strain relief boot. Note: The BTW LC multimode connector has a beige extender cap at the rear of the connector .
6 78-8135-4385-3-A 3.3 The 3.0 mm LC connector contains (A) dust cap, (B) connector , (C) metal strength sheath, (D) metal crimp slee ve, (E) strain relief boot. Note: Multimode simplex yok es are beige and singlemode yok es are blue. A B C D E 4.0 Setup 4.
78-8135-4385-3-A 7 4.4 Insert the connector into the hot melt connector holder . 4.5 Place the load adapter , with slot aligned with handle, into an av ailable port in the ov en. IMPORT ANT: Do not place connector in a hot load adapter . This ma y cause adhesive to flow to the outside of the ferrule.
8 78-8135-4385-3-A 5.0 900 micr on Cable Connector Pr eparation 5.1 Place strain relief boot on cable as sho wn. 6.0 1.6 – 2.0 mm Jack eted Cable Connector Pr eparation 6.1 Place the strain relief boot first and then the heat shrink crimp slee ve on the cable as shown.
78-8135-4385-3-A 9 8.0 Strip Guide 9.0 Stripping Pr ocedure f or 900 micr on Fiber 9.1 Place the cable on the strip template. Mark buf fer at 11 mm.
10 78-8135-4385-3-A 10.2 Snip the aramid yarn to 5-6 mm (approx. 3/16"). 10.3 Flare aramid yarn e venly around buf fer . 10.4 Using the 3M ™ Stripping T ool 6365-ST , remov e the buf fer in small increments until 21–22 mm (approx. 7/8") of buf fer is left.
78-8135-4385-3-A 11 11.0 Stripping Pr ocedure f or 3 mm Jack eted Fiber 11.1 Place the jacketed fiber on the strip template and use a fiber marking pen to mark the location of the jacket cut. Using the 3M ™ Stripping T ool 6365-ST , remov e 33 mm (1 1/3") of jacket of f cable.
12 78-8135-4385-3-A 11.5 Using the 3M ™ Stripping T ool 6365-ST , remov e the buf fer in small increments until 21–22 mm (approx. 7/8") of buf fer is left. 11.6 Using a lint-free cloth moistened with isopropyl alcohol, clean the bare fiber to remov e any oils or acrylate coating debris.
78-8135-4385-3-A 13 12.2 Maintaining fiber position in connector , push the jacketed fiber into the cable v-slot feature on the load adapter until secure. 12.3 Attempt to line up the holder arm to keep cable as straight as possible. 12.4 Remov e the load adapter from the oven by grasping the cool-touch handle.
14 78-8135-4385-3-A 13.0 Boot Placement f or 900 micron Fiber 13.1 Remov e connector from the load adapter and slide the boot ov er connector until fully seated.
78-8135-4385-3-A 15 14.3 Using the die labeled “ A” with the 3M lettering facing to the left, crimp the metal portion of the slee ve once. Note: Crimp sleeve must be bottomed against connector prior to crimping. The 3M lettered side of the crimp die should be touching the rear of the connector .
16 78-8135-4385-3-A 15.0 Crimping and Boot Placement f or 3 mm Jack eted Fiber 15.1 Remov e connector from load adapter 15.2 Slide metal crimp slee ve down and o ver aramid yarn.
78-8135-4385-3-A 17 15.5 Slide boot ov er crimp until boot is flush against the connector . Note: J ack eted boots appear the same in the photos but the boots for all 3 types of connectors are dif ferent sizes and cannot be interchanged. 16.0 Scribing 16.
18 78-8135-4385-3-A 17.0 Multimode P olish 17.1 Perform an air polish by holding the 9 micron lapping film firmly in one hand and gently moving the film in a circular motion for approximately 10 strokes or until approximately one half of the bead height is remov ed.
78-8135-4385-3-A 19 17.7 Clean the flat side of the polishing jig with a lint-free cloth moistened with isopropyl alcohol. 17.8 Place the polishing jig assembly on the lapping film. 17.9 Place the ferrule in the polishing jig aligning the latch side of the connector with the slot until it stops.
20 78-8135-4385-3-A 17.11 Polish 10 figure-eight strokes or until bead of adhesi ve is no longer visible. Note: Do not hold polishing jig assembly by the weight when polishing.
78-8135-4385-3-A 21 17.15 Good Polish (Coaxial light) 17.16 Good Polish (Oblique light) 17.17 Bad Polish – Cut or scratch going through center of core. In this picture half of fiber is missing. 18.0 Singlemode P olish to –40db 18.1 Complete steps17.
22 78-8135-4385-3-A 18.3 Place se veral drops of alcohol on to the rectangular rubber pad. 18.4 Before the alcohol e vaporates, place a sheet of the 0.5 micron pale gray diamond lapping film on the polishing pad, shiny side do wn. 18.5 Clean the lapping film with a lint-free cloth moistened with isopropyl alcohol.
78-8135-4385-3-A 23 19.0 Singlemode P olish to –55db Note: Complete steps 17.0 through 17.13 of the multimode polish and 18.0 through 18.11 of the singlemode polish before proceeding further . 19.1 Place se veral drops of alcohol on to the second gray rectangular rubber pad.
24 78-8135-4385-3-A 19.8 Leaving polishing jig assembly positioned on the lapping film rotate 180 degrees. Perform 4 additional figure eights. 19.9 Once polishing is complete , refer to steps 17.14 through 17.17 on inspecting the connector with the 200X fiber vie w scope before proceeding to final step.
78-8135-4385-3-A 25 21.3 T aper on the boot will cause the yoke to spread allo wing the correct placement at the rear of the connector . 21.4 Pinch the top and bottom of the yoke closed and press together the outer edges of the yoke, snapping firmly into connector .
26 78-8135-4385-3-A 22.0 3M ™ Expansion Kit 6650-LC and Replacement Part Numbers 6650-LC LC Expansion Kit (complete) ............................................................................80-6113-1353-9 6650-LH LC Hot Melt Connector Holder (4 ea.
78-8135-4385-3-A 27.
Important Notice All statements, technical information, and recommendations related to 3M’ s products are based on information believ ed to be reliable , but the accuracy or completeness is not guaranteed. Before using this product, you must ev aluate it and deter mine if it is suitable for your intended application.
Ein wichtiger Punkt beim Kauf des Geräts 3M 6650-LC (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie 3M 6650-LC noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für 3M 6650-LC - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von 3M 6650-LC reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über 3M 6650-LC erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon 3M 6650-LC besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von 3M 6650-LC verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit 3M 6650-LC. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei 3M 6650-LC gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
