Benutzeranleitung / Produktwartung DWL-2700AP des Produzenten D-Link
Zur Seite of 34
Manual Building Networks for People D-Link Air Premier TM D WL-2700AP Wireless Access Point This product should be installed ONL Y by experienced, professional installers who are familiar with local building and safety codes, and wherever applicable, are licensed by the appropriate authorities.
2 Content s Package Contents ................................................................................ 3 Introduction ............................................................................................ 4 Features ......................
3 1 2 3 4 5 6a 7 8 9 10 11 12 13 6b D-Link Air Premier TM DWL-2700AP Outdoor 802.1 1g Wireless Access Point Eight screws & one rubber ring T wo rubber dipole antennas Manual on CD Quick Install Gu.
4 Introduction The DWL-2700AP covers a large operating dist ance, providing an 802.1 1g outdoor WLAN which enables users to access the Internet or an organization’s network.
5 5 Different Operation modes with WDS (Wireless Distribution System) - Capable of operating in one of five different operation modes to meet your wireless networking requirements: access point (AP), Point-to-Point (PtP) bridge, Point-to-multipoint (PtMP) bridge, wireless client, or repeater .
6 Five Operational Modes AP Mode Bridge Mode.
7 Using the Configuration Utility T o configure the DWL-2700AP , use a computer which is connected to the DWL-2700AP with an Ethernet cable (see the Network Layout diagram). http://192.168.0.50 First, disable the Access the Internet using a proxy server function.
8 Note: If you have changed the default IP address assigned to the DWL-2700AP , make sure to enter the correct IP address. Home > Wizard The Home>Wizard screen will appear . Please refer to the Quick Inst allation Guide for more information regarding the Setup Wizard .
9 Using the Configuration Utility (continued) Home > Wireless Channel- 6 is the default channel. All devices on the network must share the same channel. Wireless Band- 802.1 1g SSID- Service Set Identifier (SSID) is the name designated for a specific wire- less local area network (WLAN).
10 Using the Configuration Utility (continued) Home > LAN LAN is short for Local Area Network. This is considered your internal network. These are the IP settings of the LAN interface for the DWL-2700AP . These settings may be referred to as private settings.
11 Using the Configuration Utility (continued) Advanced > Mode The DWL-2700AP can be configured to perform in any of five modes: wireless access point, wireless client, wireless bridge, multi-point bridge, repeater . Access Point is the default setting.
12 Using the Configuration Utility (continued) Advanced > Performance T ransmit Power- Choose full, half (-3dB), quarter (-6dB), eighth (-9dB), minimum power . Channel- Select from channels 1-1 1 . (FCC 1-1 1; ETSI 1-13). DTIM- (Delivery T raffic Indication Message) - 1 is the default setting.
13 Using the Configuration Utility (continued) Advanced > Filters > Wireless Access Settings Click Apply to save the changes. Access Control- Select Disabled to disable the filters function. Select Accept to accept only those devices with MAC addresses in the Access Control List.
14 Using the Configuration Utility (continued) Advanced > Filters > WLAN Partition Click Apply to save the changes. Inter-Wireless Client Connection- Enabling this feature allows wireless clients to communicate with each other .
15 Select Open System to communicate the key across the network. Select Shared Key to limit communication to only those devices that share the same WEP settings. Select Open System/Shared Key to communicate the key and require identical WEP settings to communicate.
16 Using the Configuration Utility (continued) Advanced > Grouping Select Enabled or Disabled . Click Apply to save the changes. Load Balance- User Limit (0-64)- Link Integrate- Ethernet Link Statu.
17 Using the Configuration Utility (continued) Advanced > DHCP Server > Dynamic Pool Settings DHCP Server Control- Dynamic Pool Settings- Enable or Disable the DHCP function here. Enter the starting IP address in the range. IP Assigned From- Enter the number (quantity) of IP ad- dresses in the range.
18 Using the Configuration Utility (continued) Advanced > DHCP Server > Static Pool Settings DHCP Server Control- Static Pool Settings- Enable or Disable the DHCP function here. Enter the static IP address of the de- vice here. Assigned IP- Enter the MAC ad- dress of the device here.
19 Using the Configuration Menu (continued) Advanced > DHCP Server > Current IP Mapping List Current DHCP Dynamic Pools- These are IP address pools to which the DHCP server function has assigned dynamic IP addresses.
20 Using the Configuration Utility (continued) T ools > Admin Enter a user name; admin is the default setting. User Name- T o change your password, enter your old password here Old Password- Enter your new password here. New Password- Enter your new password again.
21 Using the Configuration Utility (continued) T ools > System Apply settings and Restart. Restart- Restore to factory default settings. Restore-.
22 Using the Configuration Utility (continued) T ools > Firmware After you have downloaded the most recent version of the firmware from www .support.dlink.com you can browse your hard drive to locate the downloaded file. Click OK to update the firmware.
23 Using the Configuration Utility (continued) T ools > Cfg File Browse for the con- figuration settings that you have saved to your hard drive. Click OK when you made your selection. Update File- Click OK to load the selected settings. Load Settings to the Local Hard Drive- T ools > Misc.
24 Using the Configuration Utility (continued) This window dis- plays the settings of the DWL- 2700AP , as well as the Firmware version and the MAC address. Status > Device Info Status > Stats This window dis- plays the statis- tics of the wireless local area network.
25 Using the Configuration Utility (continued) Status > Indication Indicates the current tempera- ture. T emperature Indication- Indicates the RSSI voltage.
26 Help At this window you can access the help screens for the topics listed. Using the Configuration Utility (continued).
27 T echnical S pecifications S tandards • IEEE 802.1 1b • IEEE 802.1 1g • IEEE 802.3 • IEEE 802.3u • IEEE 802.3x Device Management • Web-Based – Internet Explorer v6 or later; Netscape Navigator v6 or later; or other Java-enabled browsers.
28 T echnical Specifications (continued) Receiver Sensitivity For 802.1 1b: • 1Mbps: -92dBm • 2Mbps: -89dBm • 5.5Mbps: -88dBm • 1 1Mbp s: -83dBm For 802.
29 LEDs • Power • 10/100M • RSSI level • 802.1 1b/g Operating V oltage • 48VDC +/- 10% for PoE Current Consumption • Max.7W without PoE (without heater) • Max.8.5W with PoE (without heater) • Max.27W without PoE (with heater) • Max.28.
30 Y ou can find software updates and user documentation on the D-Link website. D-Link provides free technical support for customers within the United S tates and within Canada for the duration of the warranty period on this product. U.S. and Canadian customers can contact D-Link technical support through our web site, or by phone.
31 Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited warranty for its product only to the person or entity that originally purchased the p.
32 • After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package.
33 Governing Law : This Limited W arranty shall be governed by the laws of the S tate of California. Some states do not allow exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limit ations and exclusions may not apply .
34 Registration 12/13/04 Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights.
Ein wichtiger Punkt beim Kauf des Geräts D-Link DWL-2700AP (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie D-Link DWL-2700AP noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für D-Link DWL-2700AP - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von D-Link DWL-2700AP reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über D-Link DWL-2700AP erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon D-Link DWL-2700AP besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von D-Link DWL-2700AP verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit D-Link DWL-2700AP. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei D-Link DWL-2700AP gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
