Benutzeranleitung / Produktwartung DVS-310-1 des Produzenten D-Link
Zur Seite of 59
.
2 D-Link DVS-310-1 User Manual Table of Contents Product Overview ........................................................ 4 Package Contents ................................................... 4 System Requirements ...................................
3 D-Link DVS-310-1 User Manual Table of Contents Example DI/DO Schematic ........................................ 56 Networking Basics .................................................... 57 Check your IP address ......................................
4 D-Link DVS-310-1 User Manual Section 1 - Product Overview System Requirements Product Overview Package Contents • Pentium 4 - 2.4GHz or higher with 512MB RAM • Windows Vista / Windows XP with SP2 or higher / Windows 2000 with SP4 or higher • Microsoft IE 6.
5 D-Link DVS-310-1 User Manual Section 1 - Product Overview Introduction C o n g r a t u l a t i o n s o n y o u r p u r c h a s e o f t h e D V S - 3 1 0 - 1 V i d e o E n c o d e r .
6 D-Link DVS-310-1 User Manual Section 3 - Conguration Hardware Overview Front Power Socket: Connect the supplied DC adapter here to power the device. LAN Port: The 10/100 Ethernet LAN port connects the Video Encoder to networking equipment such as a router or switch.
7 D-Link DVS-310-1 User Manual Section 3 - Conguration Audio In: This standard 3.5mm stereo jack accepts a connection from a microphone or any suitable analog audio input source. Audio Out: This standard 3.5mm stereo jack accepts a connection from a speaker or any suitable analog audio output device.
8 D-Link DVS-310-1 User Manual Section 3 - Conguration Hardware Installation Note: The following installation instructions assume that an analog video camera is installed and providing a signal. If necessary, please consult your camera manufacturer’s user manual for information on how to set up your analog camera.
9 D-Link DVS-310-1 User Manual Section 3 - Conguration Connect the Ethernet Cable Connect a CAT5 Ethernet cable to the LAN port of the Video Encoder. Connect the opposite end of the CAT5 cable to an active network device such as a hub, switch, or router.
10 D-Link DVS-310-1 User Manual Section 3 - Conguration Mounting Bracket Installation (Optional) Remove the four rubber feet from the bottom of the device, then afx the mounting brackets as shown below. Secure both of the brackets into place using the supplied screws.
11 D-Link DVS-310-1 User Manual Section 3 - Conguration Setup Wizard Initial Conguration This section will show you how to congure your new DVS-310-1 Video Encoder using the D-Link Setup Wizard SE. Click Wizard After loading the Setup Wizard, your Video Encoder’s IP Address will be displayed along with its corresponding MAC Address here.
12 D-Link DVS-310-1 User Manual Section 3 - Conguration Enter the Admin ID and Password . Note: The default Admin ID is admin with the password left blank.
13 D-Link DVS-310-1 User Manual Section 3 - Conguration Setup is now complete. Click Link to launch the web page of your Video Encoder, to view live video from your Video Encoder. Click Link Connect to Your Video Encoder Enter admin as the default User name and leave the Password blank.
14 D-Link DVS-310-1 User Manual Web-based Conguration Utility Conguration This section explains how to congure your new D-Link Video Encoder using the Web-based Conguration Utility. Click on the D-Link Setup Wizard SE icon that was created in your Windows Start menu.
15 D-Link DVS-310-1 User Manual This sectio n shows your Video E ncoder’s live vid eo. You can select your video prole and view or operate th e Vi deo Encoder. For additional informat ion about web conguration, please refer to the user manual included on the CD-ROM or the D-Link website.
16 D-Link DVS-310-1 User Manual Live Video This section shows your camera’s live video. You may select any of the available icons listed below to operate the camera. You may also select your language using the drop-down menu on the left side of the screen.
17 D-Link DVS-310-1 User Manual Setup Wizard To congure your Video Encoder, click Internet Connection Setup Wizar d . Alte rnative ly, you may cl ick Manu al Inte rnet Co nnection Setup to manually congure your Video Encoder and skip to page 22.
18 D-Link DVS-310-1 User Manual Select Static IP if your Internet Service Provider has provided you with connection settings, or if you wish to set a static address within your home ne two rk. E nte r t he co rre ct c on gur at ion in fo rma tio n a nd cl ick N ext to continue.
19 D-Link DVS-310-1 User Manual Congure the correct time to ensure that all events will be triggered as scheduled. Click Next to continue. If you have selected DHCP, you will see a summary of your settings, inc lu di ng t he Vi de o En co de r's IP ad dr ess .
20 D-Link DVS-310-1 User Manual This wizard will guide you through a step-by-step process to congure your Video Encoder's motion detection functions.
21 D-Link DVS-310-1 User Manual Step 3 This step allows you to specify how you will receive event notications from your Video Encoder. You may choose not to receive notications, or to receive notications via e-mail or FTP. Please enter the relevant information for your e-mail or FTP account.
22 D-Link DVS-310-1 User Manual Network Setup LAN Settings: DHCP: Static IP Address: IP Address: Subnet Mask: Default Gateway: Primary DNS: Secondary DNS: Enable UPnP: Enable UPnP Port Forwarding: Settings for your local area network.
23 D-Link DVS-310-1 User Manual Enable PPPoE: User Name: Password: HTTP Port: Access Name for Stream 1~3: HTTPS Port: RTSP Port: Maximum Upload/ Download Bandwidth: Enable this setting if your network uses PPPoE. The uniqu e name of you r acco unt . You may obt ain this inf orm at ion from your ISP.
24 D-Link DVS-310-1 User Manual Dynamic DNS DDNS (Dynamic Domain Name Server) will hold a DNS host name and synchronize the public IP address of the modem when it has been modied.
25 D-Link DVS-310-1 User Manual Image Setup In this section, you may congure the video image settings for your Video Encoder. A preview of the image will be shown in Live Video.
26 D-Link DVS-310-1 User Manual Audio and Video You may congure 3 video proles with different settings for your camera. Hence, you may set up different proles for your computer and mobile display. In addition, you may also congure the two-way audio settings for your camera.
27 D-Link DVS-310-1 User Manual Motion Detection Enabling Video Motion will turn on the motion detection feature. You may draw a nite motion area that will be used for monitoring. Enable Video Motion: Sensitivity: Percentage: Draw Motion Area: Erase Motion Area: Select this box to enable the motion detection feature.
28 D-Link DVS-310-1 User Manual Time and Date This section allows you to automatically or manually congure, update, and maintain the internal system clock for your Video Encoder.
29 D-Link DVS-310-1 User Manual Event Setup The Event Setup page includes 4 different sections. • Event • Server • Media • Recording 1. To add a new item - "event, server or media," click Add . A sc re en wi ll a pp ear a nd al lo w yo u to u pd ate t he e ld s accordingly.
30 D-Link DVS-310-1 User Manual Application In a typical application, when motion is detected, the DVS-310-1 Video Encoder sends images to a FTP server or via e-mail as notications. As shown in the illustration below, an event can be triggered by many sources, such as motion detection or external digital input devices.
31 D-Link DVS-310-1 User Manual Server Name: E-mail: FTP: Network Storage: SD Card: Enter the unique name of your server. Enter the conguration for the target e-mail server account. Enter the conguration for the target FTP server account. Specify a network storage device.
32 D-Link DVS-310-1 User Manual Media Name: Snapshot: Source: Send pre-event image(s) [0~4]: Send post-event image(s) [0~7]: File name prex: Add date and time sufx to le name: Video clip: Source: Pre-event recording: Maximum duration: Maximum le size: File name prex: System log: Enter an unique name for media.
33 D-Link DVS-310-1 User Manual Send post-event image (s) [0~7) Specify to capture the number of images after a trigger is activated. A maximum of seven images can be generated. For example: If both the Send pre-event images and Send post-event images are set to four, a total of 9 images are generated after a trigger is activated.
34 D-Link DVS-310-1 User Manual for another four seconds after a trigger is activated. File name prex Enter the text that will be added at the beginning of the le name. 1 sec. 2 sec. 3 sec. 4 sec. 5 sec. 6 sec. 7 sec. 8 sec. 9 sec. 10 sec. The moment the trigger is activated.
35 D-Link DVS-310-1 User Manual Event name: Enable this event: Priority: Delay: Trigger: Video Motion Detection: Periodic: Digital Input: System Boot: Network Lost: Video Lost: Time: Enter a name for the event. Select this box to activate this event. Set the priority for this event.
36 D-Link DVS-310-1 User Manual Trigger D/O: Server: SD: Select this option to trigger the digital output for a specic number of seconds when an event occurs. Specify the location where the event information should be saved to. This option will not be available for the Network Lost trigger.
37 D-Link DVS-310-1 User Manual Recording entry name: Enable this recording: Priority: Source: Recording schedule: Recording settings: Destination: Total cycling recording size: Size of each le for recording: File Name Prex: The unique name of the entry.
38 D-Link DVS-310-1 User Manual Format SD Card: View Recorded Picture: Playback Recorded Video: Refresh: Click this icon to automatically format the SD card and create "picture" & "video" folders. If the picture les are stored on the SD card, click on the picture folder and choose the picture le you would like to view.
39 D-Link DVS-310-1 User Manual Advanced This screen allows you to control the behavior of digital input and digital output devices. The I/O connector provides the physical interface for digital output (DO) and digital input (DI) that is used for connecting a diversity of external alarm devices such as IR-Sensors and alarm relays.
40 D-Link DVS-310-1 User Manual RS-485 You may congure the RS-485 settings or communication specications (baud rate, data bit, stop bit, and parity bit) for your Video Encoder. RS-485 is a serial communication method for computers and devices. RS-485 is used to control a PAN/TILT apparatus, such as an external camera enclosure.
41 D-Link DVS-310-1 User Manual HTTPS This page allows you to install and activate an HTTPS certicate for secure access to your Video Encoder. Enable HTTPS Secure Connection: Create Certicate Method: Status: Note: Enable the HTTPS service. Choose the way the certicate should be created.
42 D-Link DVS-310-1 User Manual Access List Here you can set access permissions for users to view your DVS-310-1. Allow list: Start IP address: End IP address: Delete allow list: Deny list: Delete deny list: The list of IP addresses that have the access right to the Video Encoder.
43 D-Link DVS-310-1 User Manual Maintenance You may modif y the name and adminis trato r’s password of your Video Encoder , as well as add and manag e the user accounts for acce ssing the Video Encoder. You may also use this section to create the unique name and congure the OSD settings.
44 D-Link DVS-310-1 User Manual Backup and Restore In this section, you may backup, restore and reset the Video Encoder conguration, or reboot the device. Save To Local Hard Drive: Local From Local Hard Drive: Restore to Factory Default: Reboot Device: You may save and document your current settings into your computer.
45 D-Link DVS-310-1 User Manual Firmware Upgrade The Video Encoder's current rmware version will be displayed on this screen. You may visit the D-Link Support Website to check for the latest available rmware version.
46 D-Link DVS-310-1 User Manual Status This page displays detailed information about your device and network connection. Device Info.
47 D-Link DVS-310-1 User Manual This page displays the log information of your Video Encoder. You may download the information by clicking Download . You may also click Clear to delete the saved log information.
48 D-Link DVS-310-1 User Manual This page provides helpful information regarding Video Encoder operation. Help.
49 D-Link DVS-310-1 User Manual Section 4 - Security D-Link’s DVS-310-1 is a versatile and cost-effective Video Encoder offering both video and audio monitoring.
50 D-Link DVS-310-1 User Manual Section 4 - Security Run the Setup Wizar d progr am fro m the CD incl ude d with the DVS-3 10-1 . Foll ow the steps in the Quick Instal lat ion Guide to congure the DVS-310-1. The Video Encoder will be assigned a local IP Address that allows it to be recognized by the router.
51 D-Link DVS-310-1 User Manual Section 4 - Security Run your Internet Explorer Web browser. In the address bar, type in the IP Address that was assigned to the Video Encoder by the Installation Wizard program. The DVS-310-1 Home Page appears with a window displaying live video from the Video Encoder.
52 D-Link DVS-310-1 User Manual Section 4 - Security 3. Access the Router with Your Web Browser The following steps generally apply to any router that you have on your network. A D-Link Router is used as an example to clarify the conguration process.
53 D-Link DVS-310-1 User Manual Section 4 - Security Note: Because a dynamic WAN IP can change from time to time depending on your ISP, you may want to obtain a Static IP address from your ISP.
54 D-Link DVS-310-1 User Manual Section 4 - Security Please make sure to check the box next to the camera name on the Port Forwarding List to enable your settings. Important: Some ISPs block access to port 80 and other commonly used Internet ports to conserve bandwidth.
55 D-Link DVS-310-1 User Manual Section 5 - Troubleshooting Troubleshooting 1. Why is the Power LED not lighting up? The power supply used might be at fault. Conrm that you are using the provided power supply, which is DC 12V, for the Video Encoder.
56 D-Link DVS-310-1 User Manual Section 5 - Troubleshooting Example DI/DO Schematic DI Rec eive s sign als fro m a reed swi tch, vibra tion senso r, or any other external security device.
57 D-Link DVS-310-1 User Manual Appendix B - Networking Basics Networking Basics Check your IP address After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically.
58 D-Link DVS-310-1 User Manual Appendix B - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please fol.
59 D-Link DVS-310-1 User Manual Appendix C - Technical Specications Technical Specications Hardware Specications • Power Supply: DC 12V / 1.25A • Removable Storage: SD Card Slot (SDHC compliant) Video Specications Codec • Simultaneous multi prole support ( H.
Ein wichtiger Punkt beim Kauf des Geräts D-Link DVS-310-1 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie D-Link DVS-310-1 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für D-Link DVS-310-1 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von D-Link DVS-310-1 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über D-Link DVS-310-1 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon D-Link DVS-310-1 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von D-Link DVS-310-1 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit D-Link DVS-310-1. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei D-Link DVS-310-1 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
