Benutzeranleitung / Produktwartung CRAFTSMAN 917.274762 des Produzenten Craftsman
Zur Seite of 56
Owner's Manual ICRRFTSMIIH°I LAWN TRACTOR 18.5 HP, 42" Mower Electric Start Automatic Transmission Model No. 917.274762 [_ his product has a low emission engine which operates differently from previously built engines.
Warranty ................................................ 2 Safety Rules .......................................... 3 Product Specifications ........................... 6 AssemblyPre-Operation ........................ 8 Operation .....................
IMPORTANT: This cutting machine is capable of amputating hands and feet and throw- ing objects. Failure to observe the following safety instructions could result in serious injury or death.
II. SLOPE OPERATION Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or death. Opera- tion on all slopes requires extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it.
• Remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment with a portable container, rather than from a gasoline dispenser nozzle. • Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete.
PRODUCT SPECIFICATIONS Gasoline 2.0 Gallons Capacity Unleaded and Type: Regular Oil Type SAE 30 (above 32°F) (API-SG-SL): SAE 5W-30 (Below 32°F) Oil Capacity: W/Filter: 3.5 Pints W/O Filter: 3.0 Pints Spark Plug: Champion RC12YC (GAP: .030") Ground Speed Forward: 5.
Steering Wheel Insert Steering Boot Hex Bolt (15)/16-18 x 4 Steering Wheel @ [L_ Steering Extension Shaft (1) Large Flat Washer u I I w Steering Wheel Adapter (1) 5/16 Lock Washer Seat (1) Washer 17/3.
Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.
7. Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down. 8. Get off seat without moving its ad- justed position. 9. Raise seat and tighten adjustment bolt securely. Seat Seat Shoulder Bolts Flat Washer djus,men, Kno @ CHECK BATTERY 1.
CHECKTIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Cor- rect tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown in "PRODUCT SPECIFICATIONS" section of this manual.
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. R N H L I',,I REVERSE NEUTRAL HIGH LOW CHOKE FAST SLOW IGNITION SWITCH O 4.
KN OW YOU R TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATINGYOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
The operation of any tractor can result in foreign objects thrown into the I eyes, which can result in severe eye damage. Always wear safety glasses I or eye shields while operating your tractor or performing any adjustments I or repairs. We recommend standard safety glasses or a wide vision safety I mask worn over spectacles.
TO ADJUST GAUGE WHEELS Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.
TO OPERATE ON HILLS _II, WARNING: Do not drive up or down hills with slopes greater than 15 ° and do not drive across any slope. Use the slope guide at the back of this manual. • Choose the slowest speed before start- ing up or down hills. • Avoid stopping or changing speed on hills.
TO START ENGINE When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. 1. Be sure freewheel control is in the transmission engaged position. 2. Sit on seat in operating position, depress clutch/brake pedal and set parking brake.
5. Move motion control lever to neutral (N) position. Shutoff engine and set parking brake. 6. Engage transmission by placing free- wheel control in engaged position (See "TO TRANSPORT" in this section of manual). 7. Sitting in the tractor seat, start engine.
FILL IN DATES /_/_X'x_'_/_ _ " AS YOU COMPLETE /__/_ _4 _/_/O.Oq. _" REGULAR SERVICE /_r/_'_r_VSERVICE DATES C hh :; kk Birakp r?sPe_;i° n _ Check Operator Presence and T ROS.
TRACTOR Always observe safety rules when per- forming any maintenance. BRAKE OPERATION If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.
NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not. • Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced,it should remain in a horizontalposition.
Oil Drain Valve Closed and Locked Position Yellow Cal: Drain Tube 3. Unlock drain valve by pushing inward slightly and turning counterclockwise. 4. To open, pull out on the drain valve. 5. After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown.
MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could cre- ate a fire hazard and/or damage. SPARK PLUG(S) Replace spark plug(s) at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first.
WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: 1. Depress clutch/brake pedal fully and set parking brake. 2. Place motion control lever in neutral (N) position. 3. Place attachment clutch in "DISENGAGED" position.
8. Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring. 9. Install belt onto engine pulley. TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See "PROD- UCT SPECIFICATIONS" section of this manual).
3. Install mower(See "To Install Mower" With parking brake "Engaged" in this section of this manual). Nut "A" Mandrel Idler Pulley TO CHECK AND ADJUST BRAKE Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.
Engine Pulley Clutching Idler I_ J_ I Keeper 11 _,,_ TRANSAXLE MOTION CONTROL LE- VER NEUTRAL ADJUSTMENT The motion control lever has been preset at the factory and adjustment should not be necessary. 1. Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.
If "jumper cables"are used for emergency starting, follow this procedure: IMPORTANT:Your tractor is equipped with a 12 volt system.The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles. Seat TO ATTACH JUMPER CABLES - 1.
ENGINE Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers expense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.
Immediately prepare your tractor for stor- age at the end of the season or if the trac- tor will not be used for 30 days or more. _ICAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CAUSE CORRECTION Will not start Hard to start Engine will not turn over 1. Out of fuel. 2. Engine not "CHOKED" properly. 3. Engine flooded.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CAUSE CORRECTION Loss of power 6. ',cont.) 7. 8. 9. Faulty spark plug. Dirty fuel filter. Stale or dirty fuel. Water in fuel. 6. Clean and regap or change spark plug.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CAUSE CORRECTION Mower blades will not rotate Poor grass discharge Poor grass discharge (contin.
SCHEMATIC 02836 193374 / 390 TRACTOR - - MODEL NUMBER 917.274762 BATTERY SOLENOID STARTER IGNITION SWITCH POSITION CIRCUIT "MAKE" OFF M+G+A1 RUN/OVERRIDE B+A1 RUN B+A1 L+A2 START 3 + S + A1 IGNITION UNIT ON TWIN CYL. ENGINES) 8CUE HOUR BLACK METER I FUEL I (OPTIONAL) I LINE I ,, {I I I .
ELECTRICAL TRACTOR - - MODEL NUMBER 917.274762 I I 41 I t I 26 34 29 I 16 ' i I I i I 93 _ I I I I I I I I 34.
ELECTRICAL TRACTOR - - MODEL NUMBER 917.274762 KEY PART NO. NO. DESCRIPTION 1 163465 Battery 2 74760412 Bolt Hex Hd 1/4-20 unc x 3/4 8 176689 Box Battery 16 176138 Switch, Interlock 21 183759 Harness Asm Light W/4152j 22 4152J Bulb Light #1156 24 4799J Cable Battery 6 Ga.
TRACTOR - - MODEL NUMBER 917,274762 CHASSIS AND ENCLOSURES 259 212 28 260 258 31 @/5 @/5 39 278 208 209 208 / 2_ 206 209 209 60 74 37 _37 208 chassis-Laser-It.
TRACTOR - - MODEL NUMBER 917.274762 CHASSIS AND ENCLOSURES KEY PART NO. NO. DESCRIPTION 1 174619 Chassis 2 176554 Drawbar 3 17060612 Screw 3/8-16 x 3/4 5 155272 Bumper Hood/Dash 9 193510X012 Dash 10 STD533710 Bolt, Carriage 3/8-16 x 3/4 11 174996 Panel, Dash, L.
TRACTOR - - MODEL NUMBER 917,274762 GROUND DRIVE 62 52 52 _ _o 36 .53 16 26 16 ; 22 _. 84 19 /" _ 5/S 2s _. .-__ 200 i 71_ 63 78 75 7876 73_16 drive-hydro.
TRACTOR - - MODEL NUMBER 917,274762 GROUND DRIVE KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. 1 Transmission (See Breakdown) 69 142432 Hydro Gear Model 314-0510 8 192502 Rod, Shift 70 134683 10 STD561210 Pin, Cotter 1/8 x 1 71 169183 14 STD551125 Washer Lock 1/4 73 169182 15 74490544 Bolt Hex Flghd 5/16-18 Gr.
TRACTOR - - MODEL NUMBER 917,274762 STEERING ASSEMBLY t j I _,_ 34 I / zz _ 1 , / L 37 i _D _ _-_- 36 88 t 29 68 15 15 15_ ............ steering pl,lt 57 82 4o 13 65 68 67 67 67 40.
TRACTOR - - MODEL NUMBER 917.274762 STEERING ASSEMBLY KEY PART NO. NO. DESCRIPTION 1 186780 Steering Wheel 2 184706 Axle Assembly Cast Iron 3 169840 Spindle Assembly, L.H. 4 169839 Spindle Assembly, R.H. 5 6266H Bearing, Race, Thrust, Hardened 6 121748X Washer 25/32 x 1-5/8 x 16 Ga.
ENGINE TRACTOR - - MODEL NUMBER 917,274762 / 31 29 33 38 14 72 / 62 13 23 OPTIONAL EQUIPMENT Spark Arrester engine-bs.lcyl 48 KEY PART NO. NO. 1 170545X505 2 17720408 3 4 137352 13 165291 14 148456 23.
TRACTOR - - MODEL NUMBER 917.274762 SEAT ASSEMBLY seat_It.knob_9 12 5 // / KEY NO. 1 2 3 4 5 6 7 8 9 10 11 PART NO. 180597 180166 71110616 19131610 145006 STD541437 124181X 17000616 19131614 180186 166369 DESCRIPTION Seat Bracket Pnt Pivot Seat (blk) Bolt Fin Hex 3/8-16 unc x 1 Washer 13/32 x 3/4 x 10 Ga.
DECALS TRACTOR - - MODEL NUMBER 917,274762 13 11 15 lO 13 12 20 5 14 KEY PART NO. NO. 1 193307 2 193960 3 186280 4 186281 5 138047 6 133644 7 191777 8 172331 9 186282 10 156439 11 186283 12 146046 13 191551 DESCRIPTION Decal, Oper. instr. Decal, Replacement Decal, Hood, R.
TRACTOR - - MODEL NUMBER 917,274762 LIFT ASSEMBLY 7 3 13 22. 48 2 6 11 5 19 13 32 32 13 19 • 1718 20 20 /-_ 16 15 lift-rh=l piece3 KEY NO. 1 2 3 4 5 6 7 8 11 12 PART NO. 159460 159471 105767X 12000002 19211621 120183X 125631X 122365X 139865 139866 DESCRIPTION Washer Asm Inner Spring Wi Plunger Shaft Asm.
TRACTOR - - MODEL NUMBER 917,274762 MOWER DECK 158 67 68 185 46 2 55 i '" 142 !147 30 117 119 118_ 6 1S 21 42 D man-t-path stlt 3 21 28 29 18 119 113 23 24 25 26 27 46.
TRACTOR - - MODEL NUMBER 917.274762 MOWER DECK KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 165892 Mower Deck Assembly, 42" 48 133944 2 STD533107 Bolt 52 139888 3 138017 Bracket As.
4_ O0 73_ 79 17 _69 7 52 L53 LI08 [125 120_ 1 10_ 14 i28 f88 f113 1° 9 _88 r124 107 6 SEALANT 57 - 20W50 OiL - 78.80Z 127- SEAL AND O-RINO KiT -r ..< 0 -I z , _ oO m, r- , zN c O W m m _r- _z .
TRACTOR - - MODEL NUMBER 917.274762 HYDRO TRANSAXLE -- MODEL NUMBER 314-0510 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 3 4 5 6 7 8 9 10 11 12 13 14 16 17 18 19 23 24 27 28 29 3O 31 32 .
TRACTOR - - MODEL NUMBER 917.274762 BRIGGS & STRATTON ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0299-E1 I 1330 REPAIR MANUAL I 11329 REPLACEMENT ENGINE I 3o7_ 358 ENGINE GASKET SET 12 20@ 524 617 0 .
TRACTOR - - MODEL NUMBER 917.274762 BRIGGS & STRATTON ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0299-E1 238 1022 6170 616 1022 404 # 914 614 _ 643 1095 VALVE GASKET SET 617 0 1022 868 _ 525 729 697 .
TRACTOR - - MODEL NUMBER 917,274762 BRIGGS & STRATTON ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0299-E1 108 692 117 93_ 1270 1266 1266A O 118 51 105A 1127 127A 276A@ 947A NIKKIJ B I 977 CARBURETOR G.
TRACTOR - - MODEL NUMBER 917.274762 BRIGGS & STRATTON ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0299-E1 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO.
TRACTOR - - MODEL NUMBER 917.274762 BRIGGS & STRATTON ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0299-E1 KEY PART KEY PART NO, NO. DESCRIPTION NO. NO.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION L_ ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. & t. Fold this page atong dotted line indicated above. 2_ Hotd page before you go that its [eft edge is vertically para[_e_ to a tree trunk or other upright structure, 3.
iiiiiiiiiiiiiiiiii[ iiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiii iiiiiiiiiiiiiii i.
Ein wichtiger Punkt beim Kauf des Geräts Craftsman CRAFTSMAN 917.274762 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Craftsman CRAFTSMAN 917.274762 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Craftsman CRAFTSMAN 917.274762 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Craftsman CRAFTSMAN 917.274762 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Craftsman CRAFTSMAN 917.274762 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Craftsman CRAFTSMAN 917.274762 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Craftsman CRAFTSMAN 917.274762 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Craftsman CRAFTSMAN 917.274762. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Craftsman CRAFTSMAN 917.274762 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
