Benutzeranleitung / Produktwartung 917.273642 des Produzenten Craftsman
Zur Seite of 56
Owner's Manual CRIIFTSMHN ° LAWN TRACTOR 18.5 HP, 42" Mower Electric Start Automatic Transmission Model No. 917.273642 This product has a low emission engine which operates differently from previously built engines.
Warranty ................................................ 2 Safety Rules .......................................... 3 Product Specifications ........................... 6 AssemblyPre-Operation ........................ 8 Operation .....................
IMPORTANT: This cutting machine is capableof amputating hands and feet and throw- ing objects. Failure to observe the following safety instructions could result in serious injury or death.
II. SLOPE OPERATION Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or death. Opera- tion on all slopes requires extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it.
• Remove gas-powered equipmentfrom the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipmentwith a portable container, rather than from a gasoline dispenser nozzle. • Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete.
PRODUCT SPECIFICATIONS Gasoline Capacity 4.0 Gallons and Type: Unleaded Regular Oil Type SAE 30(above 32°F) API-SG-SL): SAE 5W-30(Below 32°F Oil Capacity: W/Filter: 3.5 Pints W/O Filter: 3.0 Pints Spark Plug: Champion RC12YC GAP: .030") Ground Speed Forward: 5.
) Mower Leveling Wrench Bubble Level ) Keys (2) Keys (1) Oil Drain Tube For Future Use Slope Sheet Video Cassette 7.
Your new tractor has been assembled at the factory. Review the video cassette before you begin. When right or left hand is mentioned in this manual, it means when you are in the oper- ating position (seated behind the steering wheel). TO REMOVE TRACTOR FROM CARTON UNPACK CARTON 1.
4. Sit on seat in operating position, depress clutch/brake pedal and set the parking brake. 5. Place motion control lever in neutral (N) position. 6. Press lift lever plunger and raise attachment lift lever to its highest posi- tion. 7. Start the engine.
_CHECKLIST Before you operate your new tractor, we wish to assure that you receive the best performance and satisfaction from this quality product. Please review the following checklist: ,/ All assembly instructions have been completed. ,/No remaining loose parts in carton.
These symbols may appear on your tractor or in literature supplied with the product, Learn and understand their meaning. R N H L I1 REVERSE NEUTRAL HIGH LOW CHOKE FAST G G ENGINE OFF LIGHTS ON ENGINE .
KN OW YOU R TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATINGYOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
The operation of any tractor can result in foreign objects thrown into the I eyes, which can result in severe eye damage. Always wear safety glasses I or eye shields while operating your tractor or performing any adjustments I or repairs. We recommend standard safety glasses or a wide vision safety I mask worn over spectacles.
TO ADJUST GAUGE WHEELS Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.
Transmission Engaged Transmission Disengaged NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).
WARM WEATHER STARTING (50 ° F and above) 7. When engine starts, move the throttle control to the fast position. • The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.
MOWING TIPS • Mower should be properly leveled for best mowing performance. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trimming. • Drive so that clippings are discharged onto the area that has already been cut.
MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE Check Brake Operation Check Tire Pressure Check Operator Presence and T Interlock Systems R Check for Loose Fasteners A Sharpen/Repla.
TRACTOR Always observe safety rules when per- forming any maintenance. BRAKE OPERATION If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.
TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and termi- nals can cause the battery to "leak" power. 1. Remove terminal guard. 2. Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor.
ENGINE OIL FILTER Replace the engine oil filter every season or every other oil change if the tractor is used more than 100 hours in one year. AIR FILTER Your engine will not run properly using a dirty air filter. Replace pre-cleaner after every 25 hours of operation or every season.
CLEANING • Clean engine, battery, seat, finish, etc. of all foreign matter. • Keep finished surfaces and wheels free of all gasoline, oil, etc. • Protect painted surfaces with automotive type wax.
5. Connect suspension arms to rear deck brackets and secure with retainer springs. 6. Connect anti-sway bar to chassis bracket and secure with retainer spring. 7. Install belt into electric clutch pulley groove. TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground or driveway.
Mandrel "D .... D" BOTH FRONT LINKS MUST BE EQUAL IN LENGTH Front Links TO REPLACE MOWER BLADE DRIVE BELT The mower blade drive belt may be re- placed without tools. Park the tractor on level surface. Engage parking brake. BELT REMOVAL - 1. Remove mower from tractor (See "TO REMOVE MOWER" in this section of manual).
TO REPLACE MOTION DRIVE BELT Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest. BELT REMOVAL - 1. Remove mower (See "TO REMOVE MOWER" in this section of manual).
TO ADJUST STEERING WHEEL ALIGNMENT If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble with crossbars horizontal. Tighten securely. FRONT WHEEL TOE-IN/CAMBER The front wheel toe-in and camber are not adjustable on your tractor.
Keps Nut Hex Bolt Terminal Guard Positive (Red) Cable Negative '_: ' (Black) Cable TO REPLACE HEADLIGHT BULB 1. Raise hood. 2. Pull bulb holder out of the hole in the backside of the grill. 3. Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.
TO ADJUST CARBURETOR NOTE: The carburetor on this engine is low emission. It is equipped with an idle fuel adjusting needle with a limiter cap, which allows some adjustment within the limits allowed by the cap. Do not attempt to remove the limiter cap.
Immediately prepare your tractor for stor- age at the end of the season or if the trac- tor will not be used for 30 days or more. 41:_WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CAUSE CORRECTION Will not start Hard to start Engine will not turn over Engine clicks but will not start Loss of power 1. Out of fuel. 2. Engine not "CHOKED" properly.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CORRECTION Loss of power (continued) CAUSE 5. Low oil level/dirty oil. 6. Faulty spark plug. Excessive vibration Engine continues to run when operator leaves seat with attachment clutch engaged Poor cut - uneven Mower blades will not rotate 7.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM Poor grass discharge Headlight(s) not working (if so equipped) Battery will not charge Loss of drive Engine "backfires" when turning engine "OFF" CAUSE 1.
SCHEMATIC TRACTOR - - MODEL NUMBER 917.273642 BATTERY AMMETER (OPTIONAL) RED RED FUSE RED BLACK D PTO (DISENGAGED) SOLENOID I I STARTER BLACK I J ELECTRIC CLUTCH I I i CLUTCH/BRAKE I (PEDAL UP) IGNITI.
ELECTRICAL TRACTOR - - MODEL NUMBER 917.273642 I I I I I / / / / / 26 40 f I 46 29 7 / / // / i i t i i - / I I i I I i "12 34.
ELECTRICAL TRACTOR - - MODEL NUMBER 917.273642 KEY PART NO. NO. DESCRIPTION 1 163465 Battery 2 74760412 Bolt, Hex 1/4-20 x 3/4 8 7603J Tray, Battery 10 145211 Bolt, Btr Front 1/4-20 x 7-1/2 11 150109 .
TRACTOR - - MODEL NUMBER 917,273642 CHASSIS AND ENCLOSURES 217 209 54 / 54 158 278 _. 209 209 f 206 chassis-stealth,stlt 21 209 209 6O 74 209 38 60 37 > 209 14 -145 209 36.
TRACTOR - - MODEL NUMBER 917,273642 CHASSIS AND ENCLOSURES KEY PART NO. NO. DESCRIPTION 1 174619 Chassis 2 176554 Drawbar 9 161566X428 Dash 10 72140608 Bolt RDHD SQNK 3/8-16 x 1 11 167203 Panel, Dash,.
TRACTOR - - MODEL NUMBER 917.273642 GROUND DRIVE 32 30 16 1 ./ 26 52 77 32 /34 36 3O 16 @ 84 200 73 263 55 38.
TRACTOR -- MODEL NUMBER 917.273642 GROUND DRIVE KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 --- Transaxle, HydroGear, Model 62 123533X Number 314-0510 (See Break 63 174607 down) 65 10040700 8 165866 Rod Shift Fend.
TRACTOR - - MODEL NUMBER 917.273642 STEERING ASSEMBLY J J 29 46 15 40 65 33 34 35 68 13 67 67 43 / f <- 14395 / / 4,_ / / / / 8 I / 11 steering stealth prem 3 40.
TRACTOR - - MODEL NUMBER 917.273642 STEERING ASSEMBLY KEY PART NO. NO. DESCRIPTION 1 159944X428 Wheel Steering 2 184706 Axle Asm 3 169840 Spindle Asm LH 4 169839 Spindle Asm RH 5 6266H Bearing Race Thrust Harden 6 121748X Washer 25/32 x 1-5/8 x 16 Ga.
ENGINE TRACTOR - - MODEL NUMBER 917,273642 2 1 33 112 33 29 OPTIONAL EQUIPMENT I Spark Arrester 38 3 72 81 14 23 13 4 engine-bs lcyl 51 KEY PART NO. NO.
TRACTOR - - MODEL NUMBER 917.273642 SEAT ASSEMBLY 17 12 seat It,knob 14 18 I i I i I i I KEY PART NO. NO. DESCRIPTION 1 180598 Seat 2 180166 Bracket Pivot Seat 3 STD523710 Bolt Fin Hex 3/8-16 unc x 1 4 19131610 Washer 13t32 x 1 x 10 Ga 5 145006 Clip Push-In 6 STD541437 Nut Hex w/Ins.
DECALS TRACTOR - - MODEL NUMBER 917,273642 KEY PART NO. NO. 1 187407 2 138047 3 186242 Decal 4 186243 Decal 5 186572 Decal 6 146046 Decal 7 164096 Decal 8 179128 Decal 9 192830 Decal 10 156439 Decal 1.
TRACTOR - - MODEL NUMBER 917,273642 LIFT ASSEMBLY 38 40 3 / ! 12 6 5 4 13 13 19 19 lift-rh.lpiece 24 KEY NO. 1 2 3 4 5 6 7 11 12 13 15 16 17 PART NO. 179504 159476 188822 12000002 19211621 120183X 175830 139865 139866 4939M 173288 73350800 175689 DESCRIPTION Plunger Assembly Shaft Assembly, Lift Pin, Groove E-Ring Washer 21/32 x 1 x 21 Ga.
TRACTOR - - MODEL NUMBER 917,273642 MOWER DECK 117 34 149 5 6 19F 21 144 ,:_..... 4s 140 - 55 , 138 21 2 _ 23 24 <, 6 29 27 18 42 D,elec.t-path.adjwl.
TRACTOR - - MODEL NUMBER 917.273642 MOWER DECK KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 182032 Mower Housing 92 STD541437 2 STD533107 Bolt 94 132264 3 138017 Bracket Assembly, Sway .
TRACTOR - - MODEL NUMBER 917.273642 HYDRO GEAR TRANSAXLE - - MODEL NUMBER 314-0510 48.
TRACTOR - - MODEL NUMBER 917.273642 HYDRO GEARTRANSAXLE -- MODEL NUMBER 314-0510 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 170351 Main Housing, Assembly 59 170408 2 170352 Side Housi.
TRACTOR - - MODEL NUMBER 917.273642 BRIGGS ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0348-E1 I I 358 ENGINE GASKET SET 8680 43 7 146 _1 I 741 524 617 0 8420 943 0 1019 LABEL KIT II 1330 REPAIR MANUAL 30.
TRACTOR - - MODEL NUMBER 917.273642 BRIGGS ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0348-E1 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 697174 Cylinder Assembly 108 690464 2 399265 Kit-.
TRACTOR - - MODEL NUMBER 917.273642 BRIGGS ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0348-E1 1022 830 6170 @ 35 914 1095 VALVE GASKET SET 1022 868 _;_ 276(d_ 1127_ 1091 977 CARBURETOR GASKET SET 137 <>_/_._ 276 _ 267 _ 334_ 6o1_ 385<%9 I 1266A <__> 918 1 93_.
TRACTOR - - MODEL NUMBER 917.273642 BRIGGS ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0348-E1 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 383 89838 Wrench-Spark Plug 868 690968 385 694476 S.
54.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees.
Your Home © Sears, Roebuck and Co. Au Canada pour service en frangais: 1-800-LE-FOYER Mc (1-800-533-6937) www.sears.ca 02410 ® Registered Trademark / TM Trademark / SM Service Mark of Sears, Roebuck and Co. SM ® Marca Registrada / TM Marca de Fabrica / - Marca de Servicio de Sears, Roebuck and Co.
Ein wichtiger Punkt beim Kauf des Geräts Craftsman 917.273642 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Craftsman 917.273642 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Craftsman 917.273642 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Craftsman 917.273642 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Craftsman 917.273642 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Craftsman 917.273642 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Craftsman 917.273642 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Craftsman 917.273642. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Craftsman 917.273642 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
