Benutzeranleitung / Produktwartung 917.2720601 des Produzenten Craftsman
Zur Seite of 60
Owner's Manual ICRAFTSMAN°I LAWN TRACTOR 16.0 HP, 42" Mower Electric Start Automatic Transmission Model No. 917.2720601 This product has a low emission engine which operates differently from previously built engines. Before you start the engine, read and understand this Owner's Manual.
Warranty ............................................... 2 Safety Rules ......................................... 3 Product Specifications .......................... 6 AssemblyPre-Operation ....................... 8 Operation .........................
IMPORTANT: This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. Look for this symbol to point out important safety precautions.
DO: • Mow up and down slopes, not across. • Remove obstacles such as rocks, tree limbs, etc. • Watch for holes, ruts, or bumps. Uneven terrain could overturn the machine. Tall grass can hide obstacles. • Use slow speed. Choose a low gear so that you will not have to stop or shift while on the slope.
• Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area. • Never carry passengers or children even with the blades off. • Do not mow in reverse unless abso- lutely necessary. Always look down and behind before and while backing.
PRODUCT SPECIFICATIONS Gasoline 1.25 Gallons Capacity Unleaded andType: Regular Oil Type SAE 30 (Above32°F) API-SF-SJ): SAE 5W-30 (Below 32°F) Oil Capacity: 3.5 Pints Spark Plug: Champion RC12YC (GAP: .040") Ground Speed Forward: 5.5 (MPH): Reverse: 2.
Steering Wheel Insert (1) Hex Bolt 1/4-28 x 1-1/4 Steering _ Steering Wheel (1) Large Flat Washer (1) Locknut 1/4-28 (1) Locknut 1/2-20 J_ Steering Wheel Adapter Steering Extension Shaft (1) Washer 17.
(2) 7116"wrench (1) Utility knife (1) Tire pressure gauge When right or left hand is mentioned in this manual, it means, from your point of view, when you are in the operating position (seated behind the steering wheel). Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes.
Label Terminal INSTALL SEAT Adjust seat before tightening adjustment knob. 1. Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. 2. Pivot seat upward and remove from the cardboard packing, Remove the cardboard packing and discard.
INSTALL MULCHER PLATE (If previously removed) 1. Raise and hold deflector shield in upright position. 2. Place front of mulcher plate over front of mower deck opening and slide into place, as shown. 3. Hook front latch into hole on front of mower deck.
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. BATTERY CAUTION OR REVERSE FORWARD FAST SLOW WARNING ENGINE ON ENGINE OFF OIL P.
KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
I_ he operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles.
TO ADJUST GAUGE WHEELS Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.
TOWING CARTSAND OTHER ATTACH- MENTS Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.
AUTOMATIC TRANSMISSION WARMUP Before driving the unit in cold weather, the transmission should be warmed up as follows: 1. Be sure the tractor is on level ground. 2. Place the motion control lever in neutral. Release the parking brake and let the clutch/brake slowly return to operating position.
MOWING TIPS • Mower should be properly leveled for best mowing performance. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trimming. • Drive so that clippings are discharged onto the area that has already been cut.
FILL IN DATES DATES BIll I B Check Brake Opera,on _V' Check _re pressure Check Operator presence and T Interlock Systems I_ R Check for Loose Fasteners _ I_s If SharpervReplace Mower Blades _3 T .
TRACTOR Always observe safety rules when performing any maintenance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be ad- justed. (See "TO ADJUST BRAKE" in the Service and Adjustments section of this manual).
• Keep battery bolts tight. * Keep small vent holes open. • Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.
8. Use gauge on oil fill cap/dipstick for checking level. Insert dipstick into the tube and rest the oil fill cap on the tube. Do not thread the cap onto the tube when taking reading. Keep oil at "FULU' line on dipstick. Tighten cap onto the tube securely when finished.
CLEAN AIR INTAKE/COOLING AREAS To insure proper cooling, make sure the grass screen, cooling fins, and other external surfaces of the engine are kept clean at all times. Every 100 hours of operation (more often under extremely dusty, dirty conditions), remove the blower housing and other cooling shrouds.
,_ WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: 1. Depress clutch/brake pedal fully and set parking brake. 2. Place motion control lever in neutral (N) position. 3, Place attachment clutch in "DISENGAGED" position.
TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See "PROD- UCT SPECIFICATIONS" section of this manual). If tires are over or underinflated, you will not propedy adjust your mower.
Mandrel Idler ianq Pulley TO ADJUST BRAKE Your tractor is equipped with an adjustable brake system which is mounted on the side of the transaxle. If tractor requires more than six (6) feet stopping distance at high speed in highest gear on a level dry concrete or paved surface, then brake must be adjusted.
TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT The motion control lever has been preset at the factory and adjustment should not be necessary. 1. Loosen adjustment bolt in front of the right rear wheel, and lightly tighten. 2. Start engine and move motion control lever until tractor does not move forward or backward.
3. Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery. TO REMOVE CABLES, REVERSE ORDER - 1. BLACK cable first from chassis and then from the fully charged battery. 2. RED cable last from both batteries.
ENGINE Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers expense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's sen/ice outlet.
Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. ,_ CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM Will not start Hard to start CAUSE CORRECTION Enginewill not turn over 1. Out of fuel. 2. Engine not "CHOKED" properly. 3. Engine flooded.
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM Loss of power (continued) Excessive vibration Engine continues to run when operator leaves seat with attachment clutch engaged Poorcut-uneven CAUSE CORRECTION 3.
TROUBLESHOOTING CHART: See appropriate section In manual unless directed to Sears service center PROBLEM CAUSE CORRECTION Mowerbladeswill 2. Worn/damaged mower 2, Replace mower drive belt. not rotate (con't) drive belt. 3. Frozen idler pulley. 3.
SCHEMATIC TRACTOR -- MODEL NUMBER 917,2720601 [ I;,ED BATTERY SOLENOID FUSE _) w.mE AMMETER IGNITION SWITCH IGNITION SWITCH NOTE YOUR TRACTOR IS EQUIPPED WITH A SPECIAL ALTERNATOR SYSTEM. THE UGHTS ARE NOT CONNECTED TO THE BATI'ERY, BUT HAVE THEIR OWN ELECTRICAL SOURCE.
ELECTRICAL TRACTOR-- MODELNUMBER 917.2720601 22 26 I I I I I I I 27 I I I J I I I I _ I I I I I I I I I i I I i I I I i I I I I I I I I I I I I I I / / __ / l / / / // 34.
TRACTOR -- MODEL NUMBER 917.2720601 ELECTRICAL KEY PART NO. NO. DESCRIPTION 1 163465 Battery 2 74760412 Bolt, Hex Head 114-20 unc x 3/4 8 176689 Box Battery Fender 16 176137 Switch, Interlock 21 17568.
TRACTOR -- MODEL NUMBER 917.2720601 CHASSIS AND ENCLOSURES 28 39 166 208 208. 58 208 74 14 13 ." 2O8 36.
TRACTOR -- MODEL NUMBER 917.2720601 CHASSIS AND ENCLOSURES KEY PART NO. NO. DESCRIPTION 1 174619 Chassis Stamping 2 176554 Drawbar 3 17060612 Screw 3/8-16 x 3/4 5 155272 BumperHood/Dash 9 168337X013 Dash 10 STD533710 Bolt, Carriage 3/8-16xl 11 174996 Panel, Dash, L.
TRACTOR-- MODEL NUMBER 917.2720601 GROUND DRIVE 16 3_ 52 62 120 ''_ 36 30 6 38.
TRACTOR -- MODEL NUMBER 917.2720601 GROUND DRIVE KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. 1 ...... Transaxle (See Breakdown) 70 134683 Hydro Gr314-0510 71 169183 8 165866 Rod Shift Fender Adjust .
TRACTOR -- MODEL NUMBER 917.2720601 STEERING ASSEMBLY J ~f- _12 I / I ---..-__1 k u I 17 9_ z_ z_ s_ s_ 3O 43 4O.
TRACTOR - - MODEL NUMBER 917.2720601 STEERING ASSEMBLY KEY PART NO. NO. DESCRIPTION 1 139768 Steedng Wheel 2 175131 Axle Assembly STM P Dropped STL 3 169840 Spindle Assembly, L.
TRACTOR -- MODEL NUMBER 917.2720601 ENGINE 38 61 80 I OPTIONAL EQUIPMENT Spark Arrester 4O KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 4 13 14 16 23 29 31 32 33 170548 Control, Throttle 37 137040 17720408 Screw, Hox Head, Thread Cutting 38 148315 1/4-20 x 5/8 40 124028X .
TRACTOR -- MODEL NUMBER 917.2720601 LIFTASSEMBLY 7 13 6 3 2 6 19 13 32 19 13 2O 15 2O KEY PART NO. NO. 1 159460 2 159471 3 105767x 4 12000002 5 19211621 6 120183x 7 125631X 8 122365X 11 139865 12 1398.
TRACTOR - - MODEL NUMBER 917.2720601 SEAT ASSEMBLY 21 i" I i i It 12 _f 5 i _. _ f./ /J J'" ." _1_ -/ ". s I ". i " J.
TRACTOR -- MODEL NUMBER 917.2720601 DECALS 3 7 11 4 10 13 16 20 KEY PART NO. NO. 1 156811 2 177368 3 177333 4 177334 5 181422 6 133644 7 177325 8 172331 9 163204 10 156439 11 179128 KEY PART DESCRIPTION NO. NO. DESCRIPTION Decal, Oper. Instr. 12 146046 Decal, HP Engine 13 177336 Decal, Hood, R.
TRACTOR - - MODEL NUMBER 917.2720601 MOWER DECK 157 156 68 _147 142 .146 2 16 14 18 28 29 _.18 21 23 24 25 27 46.
TRACTOR - - MODEL NUMBER 917.2720601 MOWER DECK KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. 1 165892 Mower Deck Assembly, 42" 67 149846 2 STD533107 Bolt 68 144959 3 138017 Bracket Assembly,Sway.
81 77 79 73 16 93 32 _8 60 58 19 48 124 120- 19 107 "43 12 .128 o I | m_O r-m zr- cz !=c mi= m_ "nm _3J o._ .-Sl_ °_ 0 o_ 0.
TRACTOR -- MODEL NUMBER 917.2720601 HYDRO GEAR TRANSAXLE - - MODEL NUMBER 314-0510 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 170351 Main Housing, Assembly 59 170408 2 170352 Side Hou.
TRACTOR - - MODEL NUMBER 917.2720601 KOHLER ENGINE-MODEL NUMBER CV460, TYPE NUMBER 26509 CYLINDER HEAD, VALVE AND BREATHER I 24 1t 13 19 CRANKCASEJ /1 18 50.
TRACTOR-- MODEL NUMBER 917.2720601 KOHLER ENGINE-MODEL NUMBER CV460, TYPE NUMBER 26509 CYLINDER HEAD/VALVE/BREATHER CRANKCASE KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 12-032-03-S 1 25-351-01-S Lifter, valve (2) 2 2 12-755-94-S Kit, cylinder head (Includes 3-17, Gaskets 12 041 01-S 3 12-445-02-S (Qty.
TRACTOR - - MODEL NUMBER 917.2720601 KOHLER ENGINE-MODEL NUMBER CV460, TYPE NUMBER 26509 3NITIONIELECTRICAL I --9 BLOWER HOUSING AND BAFFLES I 12 AIR INTAKE I 6-- 9 m 0-8 52.
TRACTOR - - MODEL NUMBER 917.2720601 KOHLER ENGINE-MODEL NUMBER CV460,TYPE NUMBER 26509 IGNITION/ELECTRICAL BLOWER HOUSING & BAFFLES KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 2 3 4 5 6 7 8 9 10 11 17 18 19 12-086-14-S Screw, hexo flange 1 M-545010-S M10x1.
TRACTOR -- MODEL NUMBER 917.2720601 KOHLER ENGINE-MODEL NUMBER CV460, TYPE NUMBER 26509 STARTING SYSTEM I 1 8 8 Ii 8-- ENGINE CONTROLS 1 / 11 1 ! /3 OIL PAN I LUBRICATION J m 2_ 3, 1 ! 7 m_ 54.
TRACTOR-- MODEL NUMBER 917.2720601 KOHLER ENGINE-MODEL NUMBER CV460, TYPE NUMBER 26509 STARTING SYSTEM ENGINE CONTROLS KEY PART KEY PART NO. NO. DESCRIPTION NO.
TRACTOR -- MODEL NUMBER 917.2720601 KOHLER ENGINE-MODEL NUMBER CV460, TYPE NUMBER 26509 CRANKSHAFT mt EXHAUST 3 FUEL SYSTEM I 1 /' C:::D"' 56.
TRACTOR -- MODEL NUMBER 917.2720601 KOHLER ENGINE-MODEL NUMBER CV460, TYPE NUMBER 26509 FUEL SYSTEM CRANKSHAFT KEY PART KEY PART NO. NO. DESCRIPTION NO. NO, DESCRIPTION 1 M-641060-S Nut, hex. flange M6xl.O (2) 1 2 X-22-11-S Washer, lock 1/4" 2 3 M-629116-S Stud M6x1.
.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious Injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control.
For repair of majorbrand appliances in your own home... no matter who made it, no matter who sold W 1-800-4-MY-HOME _ An,prre, day or night (l e004e_4_3) (US._ andS) www,sear_.com www.sears.ca m i .i. For repair of cany in products like vacuums, lawn equipment, and electronics, call forthe nearestSears Parts and Repair Center.
Ein wichtiger Punkt beim Kauf des Geräts Craftsman 917.2720601 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Craftsman 917.2720601 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Craftsman 917.2720601 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Craftsman 917.2720601 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Craftsman 917.2720601 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Craftsman 917.2720601 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Craftsman 917.2720601 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Craftsman 917.2720601. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Craftsman 917.2720601 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
