Benutzeranleitung / Produktwartung 536.88626 des Produzenten Craftsman
Zur Seite of 54
9 Horsepower 26 Inch Dual Stage 120V. Electric Start SNOW THROWER MODEL NO. 536.886260 Caution: Read and follow all Safety Rules and Operating Instructions before first use of this product, SEARS, ROEBUCK AND CO.
WARRANTY STATEMENT ...... SAFETY RULES ............... INTERNATIONAL SYMBOLS .... ASSEMBLY ................... OPERATION .................. MAINTENANCE ............... SERVICE AND ADJUSTMENT .. 2 STORAGE .................... 28 2 TROUBLE SHOOTING CHART .
TRAINING 1. Read the operating and service instruction manual carefully. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly. 2. Never allow children to operate the equip- ment.
13. 14. 15. Never operate the snow thrower near en- closures, automobiles, window wells, drop-offs, and the like without proper ad- justment of the snow discharge angle. Keep children and pets away. Do not ovedoad the machine capacity by attempting to clear snow at too fast a rate.
Drive Clutch rd Rev_erse Auger Clutch Auger Collector Engage I÷61 / Push To Engage Fuel Electric Starter Oil Fuel Oil Mixture Discharge DOWN Discharge UP Discharge LEFT Discharge RIGHT 0 Weight Transfer Weight Transfer Transmission Lift Handle To Depress Pedal Engage To Disengage Safety Warning Symbols DANGER Thrown Objects.
Contents of Parts Bag (actual size) 1 - Owner's Manual (not shown) 1 - Packet of Fuel Stabilizer (not shown) 1 - Warranty Card (not shown) 2 - Parts bags (not shown) *Non-Assembly Parts, found in toolbox located on belt cover 1- Screw, 5/16-18 x 2 in @ 1-Split Lockwasher 1 - ,Id ut, 5/1 6-18 1-Flatwasher 11/321n.
Parts packed separately in carton (not shown full size) 1- Crank Assembly 2- Ignition Keys (Attached to engine in plastic hag) 1-Snow Chute Assembly ml II I I ,_ WARNING: Always wear safety glasses or eye shields wmle assembling snow thrower.
2. Remove and discard the packing material from around the snow thrower. 3. Cut down all four corners of the car- ton and lay the panels flat. 4. Roll snow thrower off the carton by pulling on the lower handle. CAU- TION: DO NOT back over cables. 5. Remove the packing material from handle assembly.
7. Install the 3/8" flatwasher and the 3/8" nylon Iocknut loosely on the eye bolt. 8. Carefully remove cotter pin, clevis pin and universal joint pin from yoke end of crank rod assembly. See Figure 6. 9. Place universal joint into end of worm gear lining up large holes.
SNOW CHUTE ASSEMBLY 1. Turn crank assembly counterclock- wise until it stop. 2. Position snow chute on inside of snow chute flange and align the three holes in the snow chute with holes on snow chute flange. (See Figure 9) 3. Place three 5/16-18 carriage bolts from inside of chute as shown in Figure 9.
KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your SNOW THROWER to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference.
The operation of any snow thrower can result in foreign objects being thrown into the eyes, which can result in se- vere eye damage. Always wear safety glasses or eye shields while operating the snow thrower. We recommend standard safety glasses or a wide vision safety mask for over your glasses.
Klick Pin Unlocked Position Single Wheel Drive Figure 13 NOTE: Make sure that the klick pin is in the single wheel drive position of the axle only and not through the locked position. BEFORE STARTING THE ENGINE , Before you service or start the en- gine, familiarize yourself with the snow thrower.
Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. 1. Fill the fuel tank only with a fresh, clean, unleaded regular, unleaded premium, or reformulated automo- tive gasoline.
. Push the primer button while cov- ering the vent hole as follows: Re- move finger from primer button between primes. Do not prime if temperature above 50 ° F (10 ° C). Push two time if temperature is 50 ° F (10 ° C) to 15°F (-10 ° C). Push four times if temperature is below 15 ° F (-10 ° C).
2. Release the starter handle and let it snap back against the starter. If the engine still fails to start, repeat the two previous steps until the engine starts. Then continue with the direc- tions for cold start. To help prevent possible freeze-up of recoil starter and engine controls, pro- ceed as follows after each snow remov- al job.
CUSTOMER RESPONSIBILITIES SERVICE RECORDS Fill in dates as you Before complete regular Each service. Use Often Check Engine Oil Level ! Change Engine Oil ]]ghten All Screws and _ .
PRODUCT SPECIFICATIONS HORSEPOWER 9 HP DISPLACEMENT 19.34 cu. in. GASOLINE 4 quarts CAPACITY (unleaded) OIL CAPACITY 5W30 20 oz capacity) ;PARK PLUG: Champion RJ19LM (Gap .030 in.) or equivalent VALVE CLEARANCE: Intake: .010 In. Exhaust: .010 In. SNOW THROWER AS REQUIRED The following adjustment should be preformed more than once each sea- son.
drive plate or friction wheel come in contact with grease or oil, damage to the friction wheel will result. Should grease or oil come in contact with the disc drive plate or friction wheel, be sure to clean the plate and wheel thoroughly. NOTE: For storage, the hex shaft and sprockets should be wiped with 5W30 motor oil to prevent rusting.
,_ WARNING: Always discon- nect the spark plug wire and place it where it cannot make contact with spark plug to pre- vent accidental starting when mak- ing any adjustments or repairs. TO ADJUST SKID HEIGHT This snow thrower is equipped with two height adjustment skids, located on the outside of the auger housing.
HOW TO CHECK AND ADJUST THE CABLES The cables are adjusted at the factory and no adjustment should be neces- sary. If the cables have become stretched or are sagging adjustment will be necessary.
raction Drive Belt Idler Pulley Auger Drive Belt Guide Drive Pulley Loosen this nut Figure 23 3. Loosen the nut on the idler pulley and move the pulley toward the belt about 1/8". See Figure 23. 4. Tighten the nut. 5. Press the auger drive lever.
. Remove the old auger drive belt. Replace the auger drive belt with an original factory replacement belt available from an authorized service center. 9. install the new auger drive belt onto the auger drive pulley and onto the drive pulley, 10. Adjust the auger drive belt.
HOW TO ADJUST THE BELT GUIDE 1. Disconnect spark plug wire. 2. Remove the screw. Remove the belt cover. See Figure 22. 3. Engage the auger drive lever. 4. Measure the distance between the belt guide and auger drive belt. The correct distance is 1/8 inch (3.
position for the friction wheel. See Figure 30. Leverl _,@ -" _Spring _ / J Figure 30 2. Install the bottom panel. See Figure 28. 3. Tighte_ the bolts on each side of the bottom panel.
12. Fasten the bearing plates using the four bolts removed earlier. 13. Make sure the hex shaft turns free- ly. 14. Check the adjustment of the friction wheel. See "How To Adjust The Friction Wheel" in this section. 15. Make sure the friction wheel and the disc drive plate are free from grease or oil.
2. Be sure spark plug is clean and free of foreign material. Check elec- trodes gap with a wire feeler gauge and reset gap to 0.030" if neces- sary. See Figure 34. To Replace: 1. If you need a new spark plug, use only the proper replacement spark plug.
_b ARNING: Never store your snow thrower indoors or in an enclosed, poorly venti- lated area. If gasoline remains in the tank, fumes may reach an open flame, spark or pilot light from a fur- nace, water heater, clothes dryer, cigarette, etc. NOTE: To prevent engine damage (if snow thrower is not used for more than 30 days) follow the steps below.
TROUBLE CORRECTION Difficult starting Replace spark plug, CAUSE Defective spark plug. Water or dirt in fuel system. Engine runs erratic Engine stalls Engine runs erratic; Loss of power Excessive vibration Unit fails to propel itself Unit fails to discharge snow Blocked fuel line, empty gas tank, or stale gasoline Unit running on CHOKE.
CRAFTSMAN 26" 9HP SNOW THROWER 536.886260 FRAME ASSEMBLY ENGINE MOUNTS TO FRONT HOLES ON THE FRAME 12- 13- 45 53 54 59 60 Key No. 10 12 13 41 42 43 44 45 53 54 57 58 59 6O 63 67 68 69 F-001088,.I Description Model 143.019003 SCREW, 5/16-18 WASHER, SPTLK .
CRAFTSMAN 26" 9HP SNOW THROWER 536.886260 ELECTRIC START ASSEMBLY 319051 Key No. 6 7 8 9 Description MOTOR, STARTER SCREW SCREW CORD, STARTER Part No.
CRAFTSMAN 26" 9HP SNOW THROWER 536.886260 FRAME ASSEMBLY 108 111 109 -140 91 90 88 88 91 1 199 ........... 148 Key No. 8O 88 9O 91 103 105 106 108 109 110 111 140 141 145 146 148 149 160 161 162 163 199 F-001088J Description FRAME ASSY SCREW, 5/16-18X .
CRAFTSMAN 26" 9HP SNOW THROWER 536.886260 GEAR CASE ASSEMBLY -341 3O5 3O6 327 303 310 320 3O4 312 311 Key No. Description Part No. 300 CASE, GEAR, RH 10577 301 CASE, GEAR, LH 10576 303 SCREW,1/4-20X.75 710025 304 NUT, I/4-20 302635 305 NUT, 1/4-20 HEXKEPS 303008 306 SCREW, 3/8-16X.
CRAFTSMAN 26" 9HP SNOW THROWER 536.886260 DRIVE COMPONENTS 192 190 191 19! 198 211X 195 196 193 217 221 215 223 256 277 223 271 243 226 225 226 249 250 255 224 229 246 240 276 235 244 _% 230 245.
CRAFTSMAN 26" 9HP SNOW THROWER 536.886260 DRIVE COMPONENTS Key No. Description Part No. 190 LEVER, ASSY TRACTION CLUTCH 761820 191 BEARING, FLANGE 53703 192 RING, RET E 20864 193 SPRING, RETURN 53818 195 LEVER, SPRING 579937 196 SCREW, 1/4--20X .
CRAFTSMAN 26" 9HP SNOW THROWER 536.886260 AUGER HOUSING ASSEMBLY 500 KEY# 500 IS A WELDMENT AND INCLUDES TWO SIDE PANELS REF. 5OO 544 339972 F-O01088J 36.
CRAFTSMAN 26" 9HP SNOW THROWER 536.886260 AUGER HOUSING ASSEMBLY Key No. 48O 481 482 465 490 491 493 499 50O _02 510 511 514 52O 521 522 523 524 525 526 527 540 541 544 Description PULLEY, 4L 6.12X .67 SCREW, 5/16-18X.63 KEY, SQUARE SPACER, SLEEVE .
CRAFTSMAN 26" 9HP SNOW THROWER 536.886260 DISCHARGE CHUTE ASSEMBLY 582- 593 597 594 596 595 REF. KEY# 600 I 608 - F--O01088J 38 337160.
CRAFTSMAN 26" 9HP SNOW THROWER 536.886260 DISCHARGE CHUTE ASSEMBLY Key No. Description Part No. 582 BOLT, 5/16-18 X.75 340720 583 WASHER, PLASTIC 12021 584 NUT, 5/16-18 71038 588 WASHER, PLASTIC 6711 592 WASHER, PLASTIC 12021 593 WASHER, PLASTIC 6711 594 FLATWASH ER .
CRAFTSMAN 26" 9HP SNOW THROWER 536.886260 HANDLE ASSEMBLY 72O 733 731 734 728 725 725 755- F-O01088J 40 339622.
CRAFTSMAN 26" 9HP SNOW THROWER 536.886260 HANDLE ASSEMBLY Key No. 720 724 725 726 727 728 73O 731 733 734 739 740 741 743 744 745 746 750 751 752 753 754 755 756 757 F-O01088J Description Part No. HANDLE, UPPER 9552-853 SCREW, 5/16-18X2.75 11234 WASHER, FLAT .
CRAFTSMAN 26" 9HP SNOW THROWER 536.886260 WHEEL ASSEMBLY 678 673 673 """ ..... Key No. 650 652 653 654 655 656 671 673 675 676 677 678 679 F-001088.1 Description SHAFT, AXLE SPRKT & HUB SCREW, 1/4-20X2.25 NUT, 1/4-20 HEX NYLOCK BRNG, FL CHAIN, ROLLER LINK, CHAIN MASTER FLATVVASHER .
CRAFTSMAN 26" 9HP SNOW THROWER 536.886260 SHIFT YOKE ASSEMBLY 790 -- 791 801 792 81 812 Key No, 790 791 792 795 796 8OO 801 8O2 811 812 813 F-001088J Description ROD, SHIFT SCREW, 1/4-20X.75 NUT, 1/4--20 REGHEXCTRLK NUT, 1/2-13 HEXJAM KNOB, SHIFT LEVER, SPRING SHIFT SCREW, 1/4--20X.
CRAFTSMAN 26" 9HP SNOW THROWER 536.886260 CHUTE CONTROL ROD ASSEMBLY 856 855 854 855 85O 860 862 863 867 863 i 864 873 '_ 866 874 F-001088J Key No. Description Part No. 850 CRANK, ASSY CHUTE 585426 854 HANDLE, CHUTE CRANK 307399 855 FLATWASHER .
CRAFTSMAN 26" 9HP SNOW THROWER 536.886260 DECALS VIEW FROM AU( HOUSING REAR -830 831 828 824 I [] F-O01088J VIEW FROM AUGER FRAME REAR Key No. 821 823 824 827 828 829 830 831 833 MODEL DECAL DECA.
CRAFTSMAN 4-CYCLE ENGINE MODEL NUMBER 143.019003 18 7 ¸ 87 70 69 224, 219 , . 220 328 _370G 25 26 282 370C F-OO1088J 46.
CRAFTSMAN 4-CYCLE ENGINE MODEL NUMBER 143.019003 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 0 RPM High 3550 to 3850 65 650128 Screw, 10-24 x 1/2" 0 RPM Low 2000 69 35262A Cylinder Cover Gasket 1 35385 Cylinder (Incl. 2 & 20) 70 35376 Cylinder Cover 2 27652 Dowel Pin (Incl.
CRAFTSMAN 4-CYCLE ENGINE MODEL NUMBER 143.019003 149A 35862 Valve Spring Cap 298 650665 Screw, 1/4-15 x 7/8" 150 27881 Valve Spring 300 34156A Fuel Tank 151 32581 Valve Spring Keeper (Incl.
CRAFTSMAN 4-CYCLE ENGINE MODEL NUMBER 143.019003 12 13 6/{_EI_6 t, F-O01088J KEY NO. o 1 2 3 4 5 6 7 8 11 12 13 PART NO. 590749 590599A 590600 590679 590601 590678 590680 590412 590682 590750 590535 590574 DESCRIPTION Rewind Starter Spring Pin (Incl.
CRAFTSMAN 4-CYCLE ENGINE MODEL NUMBER 143.019003 _'37 I "'" - 25 J 40"-_J F--O01088J 50.
CRAFTSMAN 4-CYCLE ENGINE MODEL NUMBER 143.019003 KEY PART NO. NO. 640052 1 631776A 2 631970 6 631778 7 650506 10 632112 14 632174 15 630735 16 632164 17 650417 18 630766 20 640016 20A 640053 25 631951.
CRAFTSMAN 4-CYCLE ENGINE MODEL NUMBER 143.019003 16 26 31J_' I I 10 5A 1 2 F-OO1088J 52.
CRAFTSMAN 4-CYCLE ENGINE MODEL NUMBER 143.019003 KEY PART NO. NO. DESCRIPTION 0 33329D Electric Starter (110 Volt) 1 33451 Dust Cover 2 33842 Retainer Ring 3 33430 Spring Retainer 4 33431 Anti--drift Spring 5A 37050 Gear & Nut (Incl. 2) 6 35449 Drive End Cap Ass'y.
r-or me repair or replacement parts you need delivered directly to your home Call 7am-7pm, 7days a week 1-800-366-PART (1 --800-366-7278) Para ordenar piezas con entrega a domicilio - 1-800-659-7084 F.
Ein wichtiger Punkt beim Kauf des Geräts Craftsman 536.88626 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Craftsman 536.88626 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Craftsman 536.88626 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Craftsman 536.88626 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Craftsman 536.88626 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Craftsman 536.88626 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Craftsman 536.88626 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Craftsman 536.88626. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Craftsman 536.88626 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.