Benutzeranleitung / Produktwartung 536.88123 des Produzenten Craftsman
Zur Seite of 24
12.5 Horsepower 33 Inch Dual Stage 120V. Electric Start SNOW THROWER MODEL NO. 536.881230 Caution: Read and follow all Safety Rules and Operating Instructions before first use of this product.
Table of Contents 2 Service and Adjustments 18-22 Warranty 2 Storage 23 Safety Rules 2-4 Troubleshooting 24 Contents of Shipping Carton 4-5 Snow Thrower Repair Parts 25-36 Assembly 5-8 Engine Repair P.
PREPARATION 1. Thoroughly inspect the area where the snow thrower is to be used and remove all doormats, sleds, boards, wires and other foreign objects. 2. Disengage all clutches before starting the engine (motor). 3. Do not operate the snow thrower without wearing adequate winter outer garments.
17. Disengage power to the auger/impeller when snow thrower is transportedor not in use. 18. Use only attachments and accessories approved by the manufacturer of the snow thrower (such as tire chains, electric start kits, etc). 19. Never operate the snow thrower without good visibility or light.
Parts packed separately in carton (not shown full size) 2 - Ignition Keys (Attached to engine in plastic bag) Z_ CAUTION: Always wear safety glasses or eye shields while assembling snow thrower, TOOLS.
HOW TO SET UP YOUR SNOW THROWER NOTE: Place fuel stabilizer In a safe place untll needed for storage. • Remove top pallet from carton. • Cut and discard the plastic ties securing the chute rod to the upper pallet and place aside. Discard pallet. • Cut all four comers of the carton from top to bottom and lay the panels flat.
• Place yoke end of crank rod around uni- versal joint, lining up openings. Insert clevis pin through assembly and secure with cotter pin. Spread ends of cotter pin to lock in place. See figure below. • Tighten nut on eye bolt, keeping eye in line with the rod while tightening the inside securely.
Position shifter lever assembly as shown in figure below. ,€ Control Panel • Reinstall bolt, spring, washer and Iocknut. See last figure on page 7, • Tighten Iocknut until 1/8 to 3/16 inch of the bolt threads protrude past the Iocknut • Thread the 3/8-16" hex jam nut onto the lever until the nut roaches the end of the thread.
KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your SNOW THROWER to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference.
Auger Drive Lever - Starts and stops the auger and impeller (snow gathering and throwing). Traction Drive Lever - Propels the snow thrower forward and in reverse. Speed Select Lever - Selects the speed of snow thrower (6 speeds forward and 2 speeds reverse).
• Engage the traction drive lever as shown in next figure, left hand. As the snow thrower starts to move, maintain a firm hold on the handles, and guide the snow thrower along the cteadng path.
FILL GAS NOTICE: ENGINES WHICH ARE CERTI- FIED TO COMPLY WITH CALIFORNIA AND US EPA EMISSION REGULATIONS FOR ULGE ENGINES: Are certified to oper- ate on regular unleadedgasoline. Include the following emisssion control system(s): EM, TWC (if so equipped).
• Connect the power cord to the switch box on the engine. • Plug the other end of the power cord into a three-hole, grounded 120 volt A.C. receptacle. • Push the primer button while covedng the vent hole as follows: (Remove finger from primer button between primes).
FROZEN RECOIL STARTER If the starter is frozen and will not turn engine: • Pull as much rope out of the starter as possible. • Release the starter handle and let it snap back against the starter. If the starter still fails to turn engine, repeat the two previous steps until the starter en- gages.
CUSTOMER RESPONSIBILITIES SERVICE RECORDS SCHEDULE Fill in dates as Mter Before As Every Every Every i Each Before first2 Each Needed 10 25 Season Storage fou complete _lour_ Use Plours Hours Hours re.
SNOW THROWER AFTER FIRST USE • Check for any loose or damaged parts after each use. • Tighten any loose fasteners, • Check and maintain the auger. AFTER EACH USE • Remove all snow and slush off the snow thrower to prevent freezing of auger or controls.
LUBRICATION • Hex Shaft and Gears - Hex shaft and gears require no lubrication. All bearings and bushings are lifetime lubricated and require no maintenance. NOTE: Any greasing or oiling of the above components can cause contamination of the friction wheel.
Z_ CAUTION: Always disconnect the spark plug wire and tie back away from the plug before making any adjustments or repairs. TO ADJUST SKID HEIGHT This snow thrower is equipped with two height adjustment skids, located on the out- side of the auger housing (see figure be- low).
• Remove fuel from tank, and stand blower on end, • Pull rubber boot off the top of the spdng. Push the cable through the spring (see figure below) to expose the threaded por- tion of the cable.
• Remove top two bolts that secure auger housing to motor mount frame. Loosen bottom two botts, Auger housing and motor mount frame will separate, hinged by bottom two bolts. • Remove old bell from auger drive pulley. • Install the original equipment replacement belt in reverse order of removal.
" --.exS.e. 3" If adjustment is necessary: • Remove washer and cotter pin connect- ing trunnion nut to speed rod (see figure below). • Twist trunnion nut up or down on shift rod to obtain the correct friction wheel posi- tion.
FdctionWheel Bolt Nut TO REPLACE AUGER SHEAR BOLT The augers are secured to the auger shaft with special bolts (see figure below) that are designed to break (to protect the machine) if an object becomes lodged in the auger housing. Use of a harder bolt will destroy the protection provided by the shear bolt.
it_ CAUTION: Never store your snow thrower indoors or in an enclosed, poody ventilated area if gasoline remains in the tank. fumes may reach an open flame, spark or pilot light from a furnace, water heater, clothes dryer, cigarette, etc. To prevent engine damage (if snow thrower is not used for more than 30 days} follow the steps below.
TROUBLE CAUSE CORRECTION Difficult starting Defective spark plug Replace defective plug Water or dirt in fuel system Use carburetor bowl drain to flush and refill with fresh fuel Engine runs er- Block.
Ein wichtiger Punkt beim Kauf des Geräts Craftsman 536.88123 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Craftsman 536.88123 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Craftsman 536.88123 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Craftsman 536.88123 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Craftsman 536.88123 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Craftsman 536.88123 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Craftsman 536.88123 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Craftsman 536.88123. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Craftsman 536.88123 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.