Benutzeranleitung / Produktwartung 247.88851 des Produzenten Craftsman
Zur Seite of 40
Owner's Manual / CRAFTSMAN 9 Horse Power 26" Two-Stage Track Drive Snow Thrower Model No. 247.888510 I! CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. Sears, Roebuck And Co., Hoffman Estates, IL 60179, U.
Content Page Warranty Information ......................................... 2 Safe Operation Practices ................................... 3 Assembly ........................................................... 6 Operation .............................
This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate your snow thrower. Failure to comply with these instructions may result in personal injury.
hand in the discharge or collector openings. Use a stick or wooden broom handle to unclog the discharge opening. Take all possible precautions when leaving the unit unattended.
Lay the hardware pieces from the hardware pack on the figure here and you will have automatically sorted these according to the steps of the assembly procedure described later. (Only one unit of each hardware has been shown per group. The number in parenthesis indicates the total number of the hardware needed in that group.
Chute / Panel IMPORTANT: This unit is shipped with engine oil, but without gasoline, in the engine. After assembly, see OPERATION section of this manual for fuel selection and fill-up. NOTE: To determine right and left hand sides of your snow thrower, stand behind the unit with the engine farthest away from you.
Secure bottom hole on the handle to the snow thrower using 5/16 x3/4" hex bolt and lock washer from the hardware pack (group A on page 5 ). Do not tighten at this time.
I I J _ook under this for i HandlePanel J / ,, Support J i Chute Crank Bracket Figure 5 You may have to loosen the carriage bolts and hex lock nuts which secure the lower chute crank bracket to the extension on the left side of the chute assembly. See Figure 6.
Attaching Clutch Cables The clutch control cables are attached to the snow thrower. If the cables are attached to the top of the engine with cable ties, cut the cable ties now. The Z ends of the clutch cables are hooked into the clutch grips on each handle.
hardware in group H ofthe hardware pack (on page 5). Pull onthe cable and rotate it around the bottom ofthe trigger, with the inner cable in the slot, until the cable end can bepushed into the trigger housing and snapped tight.
Recheck theadjustment. Tighten the jam nut against the cable when correct adjustment is reached. Adjusting Traction Drive Control • To check the adjustment of the traction drive control and shift lever, move the weight transfer lever to the transport position (shown in on ) and the shift lever all the way forward to sixth (6) position.
Knowing Your Snow Thrower Read this owner's manual and safety rules before operating your snow thrower. Compare with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference.
Operating Controls (See Figure 17.) Chute Crank The chute crank is located on the left hand side of the snow thrower. To change the direction in which snow is thrown, turn chute crank as follows: turn clockwise to discharge to the left; turn counterclockwise to discharge to the right.
Before Starting Engine Fill Gas WARNING: Gasoline is flammable and cau- tion must be used when handling or storing it. Do not fill fuel tank while the snow thrower is running, when it is hot or when it is in an enclosed area. Keep your snow thrower away from any open flame or an electrical spark and do not smoke while filling the fuel tank.
"Final Adjustments" section of the Assembly Instructions. WARNING: The electric starter must be properly grounded at all times to avoid the possibility of elec- tric shock which may be injurious to the operator. • Determine whether your house wiring is a three- wire grounded system.
two REVERSE positions. Select a speed appropriate for the snow conditions that exist. Use slower speeds until you arefamiliar with the operation ofthe snow thrower. • Squeeze the traction drive clutch grip against the right handle and the snow thrower will move.
General Recommendations • Always observe safety rules when performing any maintenance. The warranty on this snow thrower does not • cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain A the snow thrower as instructed in this manual.
Lubrication For a view of the lubrication points on the snow thrower, see Figure 20. Sprocket Shaft Lubricate the sprocket shaft with grease at least once a season or after every 25 hours of operation. IMPORTANT: Keep all grease and oil off of the friction wheel and the drive plate.
SAEviscosity grade according to the expected operating temperature. colder .,_32 o --._ warmer I 5W30 _ I SAE30 I Viscosity Chart NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi- viscosity oils will result in increased oil consumption when used above 32°F.
,& WARNING: Always stop the engine, dis- connect spark plug wire and move it away from the spark plug before performing any adjustments or repairs, Never attempt to clean the chute or make any adjustments while the engine is running.
Shift Chute Distance Lever Control Drive Auger Clutch Upper Hole Shift Lever Spring Washer Flat Washer Hak Clip Flat Washer Rod Assembly Auger Drive Belts Disconnect the chute crank at the chute assembly by removing the cotter pin and the flat washer.
Drive Belt Figure 27 To remove the front auger drive belt, push the idler pulley to the left and lift front auger drive belt from the front auger pulley.
• Reassemble the new friction wheel rubber to the friction wheel assembly tightening the six screws in rotation and with equal force. • Position the friction wheel assembly up onto the pin of the shift rod assembly and slide the shaft through the friction wheel.
if your snow thrower is left unused for30 days or longer, it needs to be prepared forstorage. Also, at the end ofthe snow season, you should follow the same set of instructions and store the snow thrower properly forthe off-season. Proper storage ensures longer life of the snow thrower.
PROBLEM Shift lever not locking into the sixth speed Engine failsto start Engine runs erratic. Loss of power Engine overheats Excessive vibration POSSIBLE CAUSE 1. Shift rod out of adjustment CORRECTIVE ACTION 1. Remove washer and pin. Turn ferrule clockwise one turn and reinstall.
SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL 247.888510 26.
Key No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 Pad No. 629-0058 684-0008A- 0637 684-0053 684-0066 684-0102 684-0111 684-0112 710-02.
SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL 247.888510 @ 28.
Key Part No. No. 1 611-0053 2 618-0043 3 618-0044 4 618-0169 7 683-0024 9 684-0014B 10 684-0021 12 684-0031 14 684-0042B 17 710-0643 18 710-0599 19 710-0602 20 710-0604 21 710-0654A 22 710-0788 23 710.
SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL 247.888510 @ r® @ 3O.
Key No. 1 2 3 4 5 6 7 8 9 11 12 13 14 15 17 18 19 20 21 22 PaR No. 631-0032 684-0009 684-0024 684-0038 710-0157 710-0459 710-0604 710-1231 712-0214 712-0346 712-0429 720-0223 731-1292 731-1538A 736-02.
SEARS CRAFTSMAN 9.0 H.P, SNOW THROWER MODEL 247.888510 NOTE: For painted parts, please refer to the list of color codes below. Please add the applicable color code, wherever needed, to the part number to order a replacement part. For instance, if a part, numbered 700-xxxx, is painted polo green, the part number to order would be 700- xxxx-0689.
Key Part No. No. 1 05931 2 605-5192A 3 605-5193A 4 618-0121 5 684-0040A 6 684-0065 7 705-5226 8 710-0703 9 710-0451 10 710-0459A 11 710-0604 12 13 14 15 16 17 18 19 710-0890A 712-0116 712-0324 712-042.
SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL 247.888510 Ref. No. 1 2 3 4 5 6 7 9 10 11 12 13 14 15 16 17 Pad No. 05896A 629-0071 710-0627 710-1245 710-0230 710-3005 710-0696 710-1652 712-0181 731-1324 .
Craftsman Engine Model No. 143.999005 for Craftsman Snow Thrower Model 247.888510 CARBURETOR Key Pad No. No. Description Qty. 0 640052 _'37 27 631024 28 632019 29 631028 30 631021 ,_,,27 31 631O22 32 27136A 33 27554 36 640005 37 632547 40 640055 44 27110 47 630748 _36 '1_,_37 I I ]3 25 48 631027 Carburetor (Incl.
Craftsman Engine Model No, 143.999005 for Craftsman Snow Thrower Model 247,888510 305 18 17 _ 83 L40 > 300 87 70 69 224_ 182 185. 3O 100 110A 343 219 3"t0G 328 [_370H 25 26 315 / 206 .
Craftsman Engine Model No. 143.999005 for Craftsman Snow Thrower Model 247,888510 Key No. 1 2 3 4 5 15 15A 15B 16 17 18 19 20 25 26 28 30 35 36 37 38 40 4O 41 41 42 42 43 45 47 48 49 5O 60 65 69 7O 71 75 76 80 81 82 83 84 86 87 89 Part No.
Craftsman Engine Model No, 143.999005 for Craftsman Snow Thrower Model 247,888510 Table continued from previous page Key Pad No. No, 220 35438 222 28820 223 650376 224 27915A 260 35447A 261 650788 262.
Craftsman Engine Model No. 143.999005 for Craftsman Snow Thrower Model 247,888510 Recoil Starter 12 13 _m5 Recoil Starter (Optional) mll Key Part No. No. Description 0 590733 1 590599A 2 590600 3 590696 4 590601 5 590697 6 590698 7 590699 8 590709 11 590734 12 590535 13 590574 Rewind Starter Spring Pin (Incl.
For the repair or replacement parts you need delivered directly to your home Call 7 am - 7 pm, 7 days a week 1-800-366-PART (1-800-366-7278) For in-home major brand repair service Call 24 hours a day,.
Ein wichtiger Punkt beim Kauf des Geräts Craftsman 247.88851 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Craftsman 247.88851 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Craftsman 247.88851 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Craftsman 247.88851 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Craftsman 247.88851 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Craftsman 247.88851 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Craftsman 247.88851 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Craftsman 247.88851. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Craftsman 247.88851 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.