Benutzeranleitung / Produktwartung 139.53675SRT des Produzenten Craftsman
Zur Seite of 40
Owner's Manual Model No. 139.53662SRT 139.53675SRT For Residential Use Only Caution: Read and follow all safety rules and operating instructions before first use of this product. Fasten the manual near the garage door after installation. Compffeswith UL325/Ih _ re_lations effective January 1, I9_3 .
Contents Page A review of safety alert syrnboFs........................................ 2 You'll need tools ............................................................................... 3 Safety information regarding garage door locks and ropes .
You'll Need Tools During assembly, installation and adjustment of the opener, instructions will call for hand tools shown below S_e_adder Tape Measure Per'<_ Hac_ Saw Claw Hammer A_ustabl.
.............. . .. ........... :., _. ........ . _ Before you begin, survey your garage area to see whether any of the conditions below apply to your installation.
Based on your particular requirements, there are several instaJlat_on steps which might call for materiaJs and/or hardware not included in the carton. '.
Carton Inventory Your garage door opener is packaged in two cartons which contain aJl parts illustrated below.. If anything is missing, carefully check the packing matedaJ.
Separate all hardware from the packages in the rail carton and the opener carton, as shown below, for the assembly and installation procedures. Assembly Hardware Waslkei'ed Screw Hex Screw Nut 5/16"-18xl/2" (2) 5/16*-18x7fS" (3) 5.
Assembly Section: Pages 8 - 11 To avoid installation difficulties, do not run the garage door opener until instructed to do so. Assembly Step 1 Assemble the T-raft & Attach the Cable Pulley Bracket . Place the 3 T-rail sections on a flat surface for assembly.
Assembly Step 2 Install the Trolley on the T-rail • Attach the threaded shaft to the trolley with the lock washer and nuts as shown° T_ey Lock Washer 5/16" Inner Nut 5/16" Hardware Shown .
Assembly Step 4 Install the Chain/Cable & Attach the Sprocket Cover Dispensing C, arlc, r_ Leave Chain and Cable {nside Dispensing Carton to Prevec_t K3nking, Kee_ Cha;n and Cable Taul When Dispensing • Detach the cable loop from the carton and fasten it to the trolley with a master tink from the hardware bag.
Assembly Step 5 _ghten the Chain & Cable • Spfn the inner nut and lock washer down the threaded shaft, away from the trolley. • To tighten the chain, turn outer nut in the direction shown.
Installation Section: Pages 12 - 27 • =, L ,,, Installation Step 1 Determine Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door. ,= = ,== ........................... , H, _de_ WaM .
Pead the Safety instructions on page 12. They also apply to doors withm_t tracks. • Close the door and mark the inside ve_c_t centedine of your garage door. Extend the fine onto the header wall above door. If headroom clearance is minimal, you can install the header bracket on the ceiling° See page 14.
Installation Step 2 Install the Header Bracket I You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the Instructions which will work best for your particular requirements.
Installation Step 3 Attach the T-rail to the Header Bracket • Position the opener on the garage floor below the header brackeL Use packing material as a protective base.
w ......... Installation Step 4 Position the Opener =ollow Instructions which apply to your door type as illustrated. A 2x4 laid flat Is convenient for setting an ideal door-to-T-rail distance. • Raise the opener onto a stepladder. You will need help at this point ff the/adder is not tall enough.
installation Step 5 Hang the Opener Two representative installations are shown. Yours may be different. Hanging brackets should be angled, Figure 1, to provide rigid support. On inished ceilings, F_gure 2, attach a sturdy metal bracket to structural supports before installing the opener.
• ,ll i installation Step 6 Install the Premium Control Console Locate the door control within sight of the door at a minimum height of 5 feet where small children cannot reach, and away from all moving parts of the door and door hardware.
6_ Attach the User Safety Instruction label to the wall near the door control, and the Maintenance Instruction label in a prominent tocai_on on the inside of the garage door. Page 32 explains how to use the door control. Do NOT connect the power and operate the openerat this time.
.... i ,,,,u,uJl Installation Step 9 Electrical Requirements To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin_ This plug will onlyfit into a grounding type cutlet.
The Safety Reversing System Information you'll need before you begin the installation of the safety reversing sensor. The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction° This is a required safety device and cannot be disabled.
Installation Step 10 " ---] Figures 2 and 3 show assembly of brackets and "C" wrap based on the recommended installation of the sensors as shown on page 21.
o Center each sensor unit in a "C"wrap with lenses pointing toward each other across the door (see _gure 6). • Secure sensors with the hardware shown° Finger tighten the wing nut on the receiving eye to allow for final adjustment. Securely tighten the sending eye wing nut.
i ,,i ,,ll, ii,ll i Installation Step 11 Fasten Door Bracket Follow Instructions which apply to your door type as illustrated below or on page 25. ILl, Ill, A horizontal brace should be long enough to be secured to 2 vertical supports. A vertical brace should cover the height of the top panel.
P'.ease read and comply with the warnings and reinforcement instructions on page 24. They apply to one-piece doors also. 1 1 I 2x4 Support Vertical Cente_ne of Ooor • Center the bracket on the top of the door, in line with the header bracket as shown.
Installation Step 12 Connect Door Arm to Trolley Follow Instructions which apply to your door type as tUustrated below and on page 27. ll,lllllll i Ill Ill :" Make sure garage door is fully close.
Assemble the Door Arm: • Fasten the straight and curved door arm sections together to the longest possible length, w_ a 2 or 3 hole ovedap. • With the door closed, connect the straight door arm section to the door bracket with the 5-16" × 1-1/4' clevis pin.
Adjustment Section: Pages 28 -30 Adjustment Step 1 Adjust the UP and DOWN Limits Do not make any limit adjustments until the safety reversing sensors are completely installed_ Limit adjustment settings regulate the points at which the door will stop when moving up or down.
ill ...... _J,J_ i,,, HH IL_ I Adjustment Step 2 Adjust the Force J,, ii i,i NIl ,,q,,iH ill ii Force adjustment controls are located on the right side panel of the opener. Force adjustment settings regulate the amount of power required to open and close the door.
Adjustment Step 3 Test The Safety Reversing Sensor , Press the remote control push button to open the door. ° Place the opener carton in the path of the door. • Press the remote control push bt_on to close the door. The door will not move more than an inch, and the opener light(s) wi!l flash.
IMPORTANT SAFETY INSTRUCTIONS ii _ L, ....... I ii i........ i_ i _,?. iiiiii To reduce the risk of severe injury or death to persons: 1. READ AND FOLLOW ALL INSTRUCTIONS. 5. If possible, use the emergency release only 2. Do not permit children either to operate or to when the door is in a closed position.
Operation of Your Opener Activate the opener with any of the following: • The Remote Control: Hold push button down until the door starts to mover - The Door Control: Hold push button down until the door starts to move.
Receiver and Remote Control Programming Your garage door opener receiver and remote control have been pro-set at the factory. The door will open when you press the LARGE remote control push button,, The code between the remote control and the receiver changes with each use, randomly accessing over 100 bilIion new codes.
Having a Problem? Situation Probable Cause and Solution "The opener doesn't operate from either the Door Control or the remote controb ....... J 1. Does the opener have electric power?. Plug a lamp into the oLr_et. If it doesn't light, check the fuse box or the circuit breaker.
*t i ,_ Having a Problem? (continued) Situation The door opens but won't close: Probable Cause & Solution i i l llll lllll i i ill i i i i Illll I I N,ll 1. If the opener lights blink, check the safety reversing sensor. See page 23, 2. If the opener lights do not blink and it is a new installation, check the down force.
Rail Assembly Parts Repair Parts 3 Installation Parts NO. NO. t 41A4884 2 41A5032 3 10A19 4 298134 5 31 D431 6 31B430 7 '10A2 8 41 A2828 9 41A4353 10 217A238 11 178B35 t 2 41 A5047 13 41A4373A 4 KEY NO.
, )p(:ner Assembly Parts I Repair Parts =nn= 19 18 17 KEY PART NO. NO. DESCRIPTION 1 31 D380 2 41 C4220A 3 41A2817 4 41 B4245 5 41 C4253 6 41 A5021-2 7 4tA4351 8 175B88 15 13 14 Sprocket cover Gear an.
ACCESS,. .............................. ,,,,,,,,, ,,,,, .......................... Sears offers many useful accessories for your garage door opener, They are Illustrated below _ tth Sears model numbers and descriptions. iii iii i ,111 ,,,,, ,,,,,, ,,,,,,,11111111 iu 139.
Index Access Door/Outside Key Release Accessory ................................................................................................ 4, 5 Electrical Safety Warnings ..........................................................................
For professional installation Cal! 24 hours a day, 7 days a week t -800-865..6500 For the repair or replacement parts you need Call 7 am - 7 pm, 7 days a week t -800-366-PART (1-800-366-7278) For in-h.
Ein wichtiger Punkt beim Kauf des Geräts Craftsman 139.53675SRT (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Craftsman 139.53675SRT noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Craftsman 139.53675SRT - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Craftsman 139.53675SRT reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Craftsman 139.53675SRT erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Craftsman 139.53675SRT besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Craftsman 139.53675SRT verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Craftsman 139.53675SRT. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Craftsman 139.53675SRT gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
