Benutzeranleitung / Produktwartung 137.248830 des Produzenten Craftsman
Zur Seite of 31
Operator's Manual 3.0 HP (Max. Developed) 10" Inch Blade 5000 R.P.M. TABLE SAW Model No. 137.248830 CAUTION: Before using this Table Saw, read this manual and follow all its Safety Rules and.
SECTION PAGE Warranty ........................................ 2 Product Specifications ....................... 2 Power Tool Safety ............................ 3 Table Saw Safety .............................. 4 Electrical Requirements and Safety ...
I_ WARNING] Before using your table saw, it is critical that you read and understand these safety rules. Failure to follow these rules could result in serious injury or damage to the table saw. Good safety practices are a combination of common sense, staying alert and understanding how to use your power tool.
. ALWAYS USE SAW BLADE GUARD, splitter and 12. anti-kickback pawls for every operation for which they can be used, including through sawing. Through sawing operations are those in which the blade cuts 13. completely through the workpiece when ripping or crosscutting.
POWER SUPPLY REQUIREMENTS I A WARNING] To avoid electrical hazards, fire hazards or damage to the table saw, use proper circuit protection. Always use a separate electrical circuit for your tools. This power tool is wired at the factory for 120V operation.
RECOMMENDED ACCESSORIES [,A WARNINGJ Visit your Sears Hardware Department or see the Craftsman Power and Hand Tools Catalog to purchase recommended accessories for this power tool. WARNINGJ To avoid the risk of personal injury: • Do not use adjustable (wobble) type dadoes or carbide tipped dado blades; maximum dado width is 1/2".
UNPACKING YOUR TABLE SAW K L 7 M A D B G J _F 7 R P Q S T V W.
Extension wing locking lever Blade guard Rip fence Table insert Side table extension wing Thermal overload reset switch ON/OFF switch & safety key Bevel angle pointer & scale Blade elevation h.
.
SAW MOUNTED TO WORK SURFACE (FIG. C) 1. If the leg set will not be used, the saw must be properly secured to a sturdy workbench using the four mounting holes at the base of the saw. 2. The surface of the table where the saw is to be mounted must have a hole large enough to facilitate sawdust fall-through and removal.
RIP FENCE (Fig. G) 1. Lift upward on the rip fence handle (t) so that the holding clamp (2) is fully extended. 2. Place the rip fence on the saw table. Lowering the front of the fence onto the table first. 3. Push down on the fence handle (t) to lock.
BLADE GUARD ASSEMBLY (FIG. K, L, M) 1. Set the blade to maximum height and the tilt to zero degrees on the bevel scale with the hand wheels. Lock the blade lock knob. 2. Place the external toothed lock washer (1) ,a steel flat washer (2) and a spring washer (10) onto the long hex head bolt (3).
INSTALLING THE TABLE SIDE EXTENSIONS- cont'd (FIG. O) 6. Snap one location seat (5) over the end of the rear table extension tube (3). Make sure the locating pin (6) in the location seat fits into the matching hole in the extension tube (Fig. O).
RIP FENCE INDICATOR ADJUSTMENT (FIG. Q) 1. The rip fence indicator (6) points to the measurement scale. The scale shows the distance from the side of the fence to nearest side of the blade. 2. Measure the actual distance with a rule. If there is a difference between the measurement and the indicator, adjust the indicator (6).
BLADE PARALLEL TO THE MITER GAUGE GROOVE (FIG. R,S) I_ WARNING I This adjustment was made at the factory, but it should be rechecked and adjusted if necessary. IA WARNING I To prevent personal injury: • Always disconnect plug from the power source when making any adjustments.
BASIC SAW OPERATIONS RAISE THE BLADE (FIG. T) To raise or lower the blade, turn the blade elevation handwheel (1) to the desired blade height, and then tighten lock handle (2) to maintain the desired blade angle. Fig. T 1 2 TILTING THE BLADE (FIG. T) 1.
CUTTING OPERATIONS There are two basic types of cuts: ripping and crosscutting. Ripping is cutting along the length and the grain of the workpiece. Crosscutting is cutting either across the width or across the grain of the workpiece. Neither ripping nor crosscutting may be done safely freehand.
BEVEL RIPPING This cut is a combination of ripping while having the blade bevel angle is set to an angle other than "0". WARNING I Cut only with the workpiece and thefenceon the right side of the blade. RIPPING SMALL PIECES I_ WARNING I Avoid injury from the blade contact.
MITERING (FIG. BB) This sawing operation is the same as crosscutting except the miter gauge is locked at an angle other than 90 ° 1_Hold the workpiece (2) firmly against the miter gauge (3). 2. Feed the workpiece slowly into the blade (1) to prevent the workpiece from moving.
MAINTAINING YOUR TABLE SAW GENERAL MAINTENANCE IA WARNING I For your own safety, turn the switch OFF and remove the switch key. Remove the plug from the power source outlet before maintaining or lubricating your saw. 1. Clean out all sawdust that has accumulated inside the saw cabinet and the motor.
I_ WARNING I To avoidinjury from an accidental start, turn theswitch OFF and always remove the plug from thepower source before making any adjustments. • Consult your local Sears Service Center if for any reason the motorwill notrun. SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION 1.
10" TABLE SAW PARTS LIST MODEL NO. 137.248830 IA WARNING I When servicing use only CRAFTSMAN replacement parts. damage. IA WARNING I Use of any other parts may create a HAZARD or cause product Any attempt to repair or replace electrical parts on this Table Saw may create a HAZARD unless repair is done by a qualified service technician.
26Ji7 W -'_'. t- o rn _> u) 0 m F- z 0 4_ CO CO.
10" TABLE SAW PARTS LIST Schematic B MODEL NO. 137.248830 I.D. NO. Description Size 08VH CI ,AMP.¢ ORD #06 0AW4 BODY SHEI.L #AM 0BIW HANDLE BAi_ ASS'Y 0B_:_ SABI)LE 0B24 SPkLN(} 0B27 _)[NTER i_I_ACt(ET 0B2B NEEDLE POINTER 0B_ SWITCH BOX #06 0B4_ RETAIN[N(} CLP 0B4S WARNIN(; i.
W "4" F- _' m OT04 OIPA 0 m r- z 0 k_ 4_ CO CO 0.
10" TABLE SAW Part list for STAND MODEL NO. 137.248830 I,D. No. Description Size Qty 0A4T BASE #06 2 0EAA BRACKET 4 0EAN UPPER SUPPORT 1 0EAP UPPER SUPPORT 1 0EAY UPPER SUPPORT 2 0EBB BOTTOM SUPPORT BRACKET 2 0EBG BOTTOM SUPPORT BRACKET 2 0J4F FLAT WASHER ci_ 8X16-2.
r- m -.j 0 m I-- Z 0.
10" TABLE SAW Part list for MOTOR MODEL NO. 137.248830 I.D. NO. DESCRIPTION SIZE QTY 1502 FIELD ASS'Y 1 0HX9 NEEDLE BEARING 1 0JAL EXT.TOOTH LOCK WASHER _;,_4 4 0JX3 HEX. SOC. SET SCREW M5X0.8-8 2 0K3A CR.RE. PAN HD. SCREW & WASHER M5X0.
f_fJ ;r o --I O W r- rrl (t) / i ;r 0 113 r- Z O €_ 4:_ co co €_ c_.
,.._J , i Cut off here to _--- push 1/2" wood. - [ --- 1/2" Squares. l _ ..... j PUSH STICK Make from 1/2" or 3/4" wood or thickness less than width of material to be cut. ] Optional hanging hole. CAUTION! _ Use only good strong wood or plywood.
Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and Operator's Manuals that you need to do-it-yourself.
Ein wichtiger Punkt beim Kauf des Geräts Craftsman 137.248830 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Craftsman 137.248830 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Craftsman 137.248830 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Craftsman 137.248830 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Craftsman 137.248830 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Craftsman 137.248830 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Craftsman 137.248830 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Craftsman 137.248830. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Craftsman 137.248830 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.