Benutzeranleitung / Produktwartung TLC18-CHP des Produzenten Country Home Products
Zur Seite of 36
DR CHIPPER Operating & Assembly Instruction Manual Model: 18.0 HP TLC18-CHP This manual contains informati on concerning pr oper and improper operating procedures, warnings, maintenance, troubleshooting, assembly, and tips. Everyone who operates this machine should read these instructions and be thoroughly familiar with them.
SECTION I - SAFETY This symbol points out impor tant safety instructions , which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate your chipper.
WARNING California to cause cancer, birth def : The Engine Exhaust from this product contai ns chemicals known to the state of ects or other reproductive harm. MAKE CERTAIN THAT ALL SAFETY LABELS ON THIS EQUIPMENT ARE KEPT CLEAN AND IN GOOD CONDITION.
091-0057 091-0059 091-0062 091-0088 091-0093 4.
091-0256 091-0378 091-0379 091-0380 091-0381 5.
091-0384 913-0265 6.
SAFE OPERATION PRACTICES TRAINING • Read this owner’s manual carefully in its entirety bef ore attempting to assemble this machine. Read, understand, and follow all instructions on the machine bef ore operation. Be completely familiar with the controls and the proper use of the machine before operating it.
OPERATION • Never place your hands, feet, or any part of your body in the chipper chute, discharge opening, or near or under any moving part while the engine is running. Keep clear of the discharge opening at all times. If it becomes necessary to push material into the chipper chute, use a small diameter stick, NOT YOUR HANDS.
• Do not allow an accumulation of processed material to build up in the discharge area as this will prevent proper discharge and can result in kick-back from the chipper chute.
• Only operate your chipper from the operator zone. • Know how to turn your unit off. • Never move your chipper or leave it unattended with the engine running. • Do not operate your chipper on concrete or blacktop. • Follow engine owner’s manual for engine maintenance and repair.
SECTION II - ASSEMBLY INSTRUCTIONS PACKAGE CONTENTS SKID PARTS BO X BOLT BA G CHIPPER CHIPPER HOPPER 7 EA – 5/16-18 X ¾” CARRIAGE BOLTS DISCHARGE CHUTE SWIVEL TOP 8 EA – 5/16-18 NYLOCK NUT HITC.
STEP III – ATTACHING THE HITCH ARMS AND TRAILER HITCH ASSEMBLY 1. Attach the hitch arms (item #39, pg. 29) to the traile r frame using the two hitch arm mounting plates (item #52, pg. 29) and four 1/2”-13 x 1-1/4” HHCS (ite m #38, pg. 29) from the bolt bag.
STEP V – ATTACHING THE SWIVEL TOP AND DEFLECTOR 1. Get three 5/16-18 X ¾” carriage bolts (item #2, pg. 29) , two 5/16-18 nylock nuts (item #5, pg. 29), three 3/8” flat-washers(item #60, pg. 30), and the locki ng knob (item #12, pg 29) from the bolt bag.
STEP VI – ATTACHING THE WIRE HARNESS Identify the “road side” and “curb side” of your trailer per the picture below. The mounting brackets have an access hole in them so the wire harness can be attached to the light. On the wire harness the yellow/brown wire is for the road side light and the green/brown wire is for the cu rb side light.
SECTION III - OPERATION BEFORE STARTING ENGINE, ALWAYS CHECK OIL LEVEL! Refer to the engine owner’s manual for further details regarding OPERATION AND MAINTENANCE OF the engine. NOTE: ENGINE IS SHIPPED WITHOUT OIL! FILL CRANKCASE WITH OIL BEFORE STARTING ENGINE.
CHECKING AND ADDING OIL • Check oil level before starting the engine. • Check level daily, or after every eight hours. • Keep oil level at FULL. • Do not overfill. Oil filling procedure: first add 1 quart. Start and run engine at idle for 30 seconds.
STARTING AND STOPPING STARTING AND OPERATING TIPS • Store and fuel equipment in level position. • Use fresh fuel. • Use correct type of oil. • Remove external equipment/engine loads. • Periodically remove any debris buildup from the machine.
SECTION IV - CHIPPING THIS CHIPPER WAS DESIGNED FOR CHIPPING LIMBS OR BRANCHES. NEVER USE THIS MACHINE FOR ANY OTHER PURPOSE AS IT COULD CAUSE SERIOUS INJURY. SAFETY FIRST • Always wear protective gloves and safety glasses during operation of the chipper.
• USE COMMON SENSE WHEN USING YOUR CHIPPER. • LEARN TO RECOGNIZE THE CHANGE IN THE SOUND OF YOUR MACHINE WHEN IT IS OVERLOADED. • BECOME FAMILIAR WITH SUCCESSFUL OPERATING CONDITIONS AND AVOID THOSE THAT CAN OVER LOAD AND DAMAGE THE MACHINE. • IF THE MACHINE BECOMES JAMMED BY OVERLOADING OR ANY OTHER CAUSE, STOP THE MACHINE IMMEDIATELY.
TO FREE A JAMMED FLYWHEEL • Stop the engine. • Remove both spark plug wires and keep away from spark plugs. • Disconnect battery at negative terminal. • Remove any material left in the chipper hopper. • Remove discharge chute weldment. NOTE: Never pry against the scroll weldment when removing the discharge chute or at any other time.
SECTION V - MAINTENANCE AND STORAGE IMPORTANT: The knife should be checked for sharpness and the nuts and bolts attaching it to the flywheel for tightness every 8-10 hours of operation.
REMOVAL, SHARPENING AND RE-INSTALLATION OF CHIPPER KNIFE HOW TO REMOVE THE KNIFE • Stop the engine. • Remove both spark plug wires and keep away from spark plugs. • Disconnect battery at negative terminal. • Remove both access covers from the chipper basic machine.
• The knife should never be sharpened to the extent that more than 3/32” is taken off this measurement. • Once this measurement is below 7/32” (s ee figure 3) the knife should be replaced. • If you are unable to remove dents or gouges wit h these guidelines, replace the knife.
AFTER ANY BLADE OR WEAR PLATE MAINTENANCE OR ADJUSTMENT, ROTATE THE CHIPPER DISK BY HAND. WATCH AND LISTEN CAREFULLY FOR ANY UNUSUAL NOISES, CLICKING OR VIBRATION. IF ANY OF THESE ARE DETECTED, INSPECT THE MACHINE FOR DAMAGE, REPAIR OR REPLACE ANY DAMAGED PARTS AND CHECK FOR ANY LOOSE PARTS AND RETIGHTEN.
INSTRUCTIONS FOR ADJUSTING OR REPLACING BELT BELT ADJUSTMENT The belt on your chipper should deflect 3/8” under three pounds of pressure as shown in figure 1 below. If it doesn’t, adjust per the following directions. Figure 1 • Remove belt guard.
TROUBLESHOOTING SYMPTOM PROBLEM CORRECTION Clutch overheats. Belt burns. Flywheel won’t turn. Clutch is slipping or flywheel is jammed or stopped. • Immediately stop engine. • Remove spark plug wires. • Turn flywheel by hand to be sure it turns freely.
LUBRICATION AND MAINTENANCE OPERATION TIME PROCEDURE COMMENTS BREAK IN • Change engine oil and filter after first five hours. • Check belt tension. • Check all nuts and bolts for tightness. • Follow oil recommendations per the engine & owner’s manual.
CENTRIFUGAL CLUTCH INSTALLATION AND SERVICING INSTRUCTIONS FOR CLUTCH 911-0236 REMOVAL 1. Remove clutch from shaft by removing bolt and washers. 2. Slide clutch off shaft. 3. Remove key from keyway. INSTALLATION 1. Clean the shaft and remove any burrs.
SECTION VI – PARTS LIST & ASSEMBLY DRAWINGS TLC18-CHP PARTS LIST ITEM # PART # QTY DESCRIPTION 1 030-0325 1 18HP B&S VANGUARD ENGINE 2 090-0462 10 5/16-18 X 3/4" CARRIAGE BOLT 3 913-037.
TLC18-CHP PARTS LIST ITEM # PART # QTY DESCRIPTION 43 090-0234 3 3/8 USS FLATWASHER 44 408-0078 2 SAFETY CHAIN 45 911-0220 1 HITCH TUBE WELDMENT 46 913-0218 1 TRAILER HITCH 47 090-0370 4 1/2-13 X 3&qu.
31.
32.
913-0232 CHIPPER BASIC MACHINE ITEM # PART # QTY DESCRIPTION 1 090-0048 9 5/16-18 GRIPCO LOCKNUT 2 030-0115 2 BEARING 3 090-0233 8 5/16 USS FLATWASHER 4 090-0049 4 3/8-16 GRIPCO LOCKNUT 5 030-0117 1 R.
34.
NOTES 35.
NOTES COUNTRY HOME PRODUCTS Meigs Road, P.O. Box 25, Vergennes, Vermont 05491 1(800) DR-OWNER (376-9637) 12/31/03 36.
Ein wichtiger Punkt beim Kauf des Geräts Country Home Products TLC18-CHP (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Country Home Products TLC18-CHP noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Country Home Products TLC18-CHP - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Country Home Products TLC18-CHP reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Country Home Products TLC18-CHP erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Country Home Products TLC18-CHP besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Country Home Products TLC18-CHP verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Country Home Products TLC18-CHP. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Country Home Products TLC18-CHP gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
