Benutzeranleitung / Produktwartung Steam Oven des Produzenten Cleveland Range
Zur Seite of 30
260AZH REV. B 3/06 This kit connects a PC to as many as 31 Combis at a maximum distance of 3280 Feet (1000 meters). The software can download cooking programs, reco rd HACCP information, and monitor the networked Combis in real-time. This installation manual incl udes instru ctions for both RS232 and USB connection s for a PC.
2 1 Software-CD - 300550 2 Network Connection Cable – 300551 (included onl y w/ 232 kit) 3 Dongle - C5009210 4 PC Interface Converter - C5009156 (included only w/ 232 kit) 5 9 Volt Power Supply for .
3 1 Electronic Board (1) – C5019104 2 Connector (1) – C5002091 3 Bracket with Studs (1) – C2114799 4 Control Panel Spacers (2) – C8009030 5 Screws – M3 (2) - 111633 6 Lock Washers (2) – C8.
4 TO CONNECT THE RS232 CONVERTER TO THE PC Photos 4, 5, and 6 show the correct cable c onnections from the PC to the PC Converter for RS232. Note the position of the Dongle on the PC in Photo 5. Make sure the PC Converter is connected to the 9-volt DC power supply as shown in Photo 7.
5 NOTE: A: RED WIR E B: BLACK WIRE GROUND: GR OUND OR SH IELD WIRE RS232 CABLE CONNECTION FOR CONVERTER TO RS485 ONLY Photo 8 shows the cable connections for the PC Converter.
6 TO CONNECT USB CONVERTER TO RS485 ONLY IMPORTANT : ALWAYS USE THE SAME USB PORT WHE N RE ATTACHING THE USB CA BLE TO THE PC! See Page 20 for instructions for USB hardwa re and software installation and setup. The USB software must be installed on the PC before using the USB adapter.
7 Remove the Control Side Cover Turn the 1/4 turn quick-locks to loosen. From the bottom edge of the side panel, push up and pull out. Remove the side panel and set it aside.
8 Remove the Control Panel Photo 17 Press down and turn counterclockwise to remo ve the Operation P anel retention screw. Photo 18 Remove the Operation Panel out from the rear. Be careful not to drop it. Disconnect the computer cable from the Op eration Panel and set the panel aside.
9 Attaching the Base Plate to the Communication Module 1. Mount the board to the panel using the spacers, nuts and washers included in the kit. Photo 20 Photo 21 Press the Communication Module Inte rface onto the Control Module. Tighten the screws holding the Communicati on Module to the Control Module.
10 Attaching the Base Plate to the Communication Module Mount the board to the panel using the spacers and nuts included in the kit. Photo 24 Complete Assembly of Communication Module Interface and Control Module.
11 Inserting the Communication M odule Cable into the Oven Photo 30 Remove the sanitary seal plug from the underside of the Combi. Photo 31 Insert the new bushing, P/N 111751 into the opening.
12 Photo 25 Photo 2 6 Connect the Network Cable to the Communication Module T ake care to match the wire ends or colors to the connections throughout the network to avoid miswiring. For RS232 Converter : Attach the wire to the Converte r at connection “A” and attach the other end to connection “A” on the Communi cation Module.
13 Setting the Jumpers on the Communication Module Photo 27 Jumper setting for the first Comb i and all Combis in the Network. To set the jumpers: gently pull them fr om the board and insta ll them as shown. Photo 28 Wire Connection and jumpers positions for la st communication module in the Network.
14 Photo 33 Secure cable to the upper right spacer as shown in Photo 36. Photo 35 Place Control Board and Modul e back into the Combi. Use wire ties to secure cable away from high voltage, sharp corners and edges, and moving parts. Make sure the Control Board can still be re moved from the Combi once the Network Board and cables are attached.
15 Replace the Operation Panel Photo 36 Remount the Operation Pane l back into the Combi. Photo 37 Press down and turn clockwise to tighten the Operation Panel retention screw.
16 Replace the Control Side Panel Photo 38 Photo 39 Push up and in from the bo ttom edge of the side panel. P h o t o 4 0 P h o t o 4 1 Turn the 1/4 turn quick-locks to tighten.
17 Directions for Installing the USB Adapter 1. Plug the USB connector into the adapter and connect to one of the USB ports on the back of your computer.
18 Select install from a list of specific location (advanced) Ignore this screen if it appears:.
19 Uncheck “Include this location in the search.” Click Next. Let search.
20 The Hardware wizard will appear a second time:.
21 Follow the directions in each screen..
22 Allow search for CD.
23 Click Finish to close the screen. Configure your serial device: 1. Right click My Computer, select properties: Then select the “Hardware tab” and click on the “Device Manager” button.
24 Expand the Ports (COM & LPT) device.
25 Right click on the “USB Seri al Port (COM??)” item. The ?? will be a number great er than 0 and less than 255. Select the Port Settings tab..
26 Note the COM setting. Only COM1, COM2, COM3, and COM4 can be used by the HACCP software. To change the COM num ber, click the Advanced button..
27 If needed click the COM Port Number: drop menu and select and acceptable port number. If all are marked as (i n use) then change one of the other serial devices to a COM port number higher than 4.
28 For USB to RS485 Switches 1 and 4 are ON For USB to RS232 Switches 2, 3, 4 are ON 6. Once the c omputer recognizes the USB adapter, the dip swit ches in the adapter have to be set up for RS485 or RS232 data transfer; chos e the correct setting to match the configurati on you are using.
29 Jumper #1 Position SHOWS WIRE CONNECTIONS PIN 1, PIN 2, AN D GRO UND (PIN 6). 7. For the adapter to output data for RS485, a jumper insi de the metal case must be positioned correctly. This photo shows t he position of the #1 jumper. All other jumpers should be in the original position.
260AZH REV. B Rev Page 116 March 2006 This Page for Internal Reco rd Only, Not for Printing Cleveland Range, LLC 1333 East 179 th St, Cleveland, Ohio 44110 Drawing No.
Ein wichtiger Punkt beim Kauf des Geräts Cleveland Range Steam Oven (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Cleveland Range Steam Oven noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Cleveland Range Steam Oven - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Cleveland Range Steam Oven reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Cleveland Range Steam Oven erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Cleveland Range Steam Oven besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Cleveland Range Steam Oven verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Cleveland Range Steam Oven. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Cleveland Range Steam Oven gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
