Benutzeranleitung / Produktwartung iDP-3210 des Produzenten Citizen Systems
Zur Seite of 65
Rev. Issued Japan CBM Corporation Information Systems Div. User ’ s Manual Line Thermal Printer Model : iDP-3210.
iDP-3210 User ’ s Manual CITIZEN 2 1996.08.02(10-DCL)15 Declaration of Conformity Manufactu r er's Name : : Japan CBM Corporation Manufactu r er's Address : 1-1-7, Okubo, Shinjuku-ku, Tokyo 169, Japan Declare the Product Product Name Thermal Printer Model Number (s) iDP3210 (iDP3210R, iDP3210P) (S.
iDP-3210 User ’ s Manual CITIZEN 3 IMPORTANT SAFETY INSTRUCTIONS l Read all of these instructions and save them for later reference. l Follow all warnings and instructions marked on the product. l Unplug this product from the wall outlet before cleaning.
iDP-3210 User ’ s Manual CITIZEN 4 IMPO RT ANT: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications.
iDP-3210 User ’ s Manual CITIZEN 5 <Cautions> 1. Before using the equipment, be sure to read this User ’ s manual thoroughly. Please keep this manual handy to refer to when needed. 2. Portions of the contents of this User ’ s manual may be changed without prior notice.
iDP-3210 User ’ s Manual CITIZEN 6 ! WARNING l Do not subject this equipment to excessive force or shocks such as by treading on it, dropping it or hitting it. l Do not install this equipment in locations with poor ventilation, and do not use the equipment in such way that the ventilation port is obstructed.
iDP-3210 User ’ s Manual CITIZEN 7 Precautions for installation l Do not install or store this printer near fire, water, a heater, in the direct sunshine in the locations such as high-temperature, high humidity, oily and dusty. This may cause fire and abnormality.
iDP-3210 User ’ s Manual CITIZEN 8 Caution for Handling Do not carry out the following operation, since they may damage the printer. l Do not carry out blank printing in the condition where there is no recording paper, this may damage the print head.
iDP-3210 User ’ s Manual CITIZEN 9 This Caution label is attached in the following position. Make sure to use this equipment properly reading the cautions for handling carefully. This label indicates the danger of burn due to the heat of print head.
iDP-3210 User ’ s Manual CITIZEN 10 Ordinary Maintenance l Make sure to maintain the equipment after switching OFF the power . l When cleaning the platen of printer mechanism, wipe out the dirty portion by a cotton pud dipped into ethyl alcohol. l When cleaning the surface of the main unit case, use soft cloth.
iDP-3210 User ’ s Manual CITIZEN 11 CONTENTS 1. OUTLINE ....................................................................................................................................................................... 13 1.1 Features .........
iDP-3210 User ’ s Manual CITIZEN 12 7. Drawer Kickout Connector ............................................................................................................................................. 43 7.1 Specifications .....................
iDP-3210 User ’ s Manual CITIZEN 13 1. OUTLINE This printer, a small-sized line thermal printer, has been developed to be applicable to various data communication terminals, POS terminals, kitchen printers, etc.. Since the printer is equipped with abundant functions, it can be used widely in various applications.
iDP-3210 User ’ s Manual CITIZEN 14 (2) When using the printer, remove the protective paper of the thermal head in the following manner: 1) Open the printer cover. 2) Holding the paper guide of the platen roller section, pull it in the arrowed direction.
iDP-3210 User ’ s Manual CITIZEN 15 2. BASIC SPECIFICATIONS 2.1 Model Classification iDP3210 - R F 120 AC Adapter 120 : for AC 120V 230 : for AC 230V Model name Character set F: International Interf.
iDP-3210 User ’ s Manual CITIZEN 16 2.2 Basic Specifications Item Description Printing system Line thermal dot printing system Print width 73.92 mm/448 dots Dot pitch Horizontal 0.165mm (approx. 6 dots/mm) Vertical 0.163mm (1/156 inch) Printing speed 73.
iDP-3210 User ’ s Manual CITIZEN 17 2.3 Printing Paper Specifications 2.3.1 Recommended Paper Type : Thermal paper Paper width : 80 plus 0/minus 1 mm Paper thickness : 65 ± 5 micro m Roll diameter : Ø83mm or less Printed surface : Outside of the roll (surface) Recommended paper : TF50KS- E2C by Nippon paper Mil.
iDP-3210 User ’ s Manual CITIZEN 18 2.3.2 Printing position 2.3.3 Head and Cutter Layout.
iDP-3210 User ’ s Manual CITIZEN 19 3 OUTER APPEARANCE AND COMPONENTS.
iDP-3210 User ’ s Manual CITIZEN 20 4.OPERATION 4.1 Connecting AC Adapter (1) Turn off the power switch. (2) Holding the AC Adapter cable connector with its arrowed side facing downward, put it into the power connector on the rear side of the printer.
iDP-3210 User ’ s Manual CITIZEN 21 4.2 Connecting Interface Cable (1) Turn OFF the power switch. (Both for the printer and the host side.) (2) Confirming the up and down side of the cable terminal, connect it to the interface connector. (3) Fix the cable terminal.
iDP-3210 User ’ s Manual CITIZEN 22 4.3 Connecting Drawer Kickout Connector (1) Turn OFF the power switch. (2) Confirming the up and down side of the drawer kickout cable connector, put it into the drawer kickout connector on the rear side of the printer.
iDP-3210 User ’ s Manual CITIZEN 23 4.4 Inserting the Paper Roll Cautions : Do not use a paper roll other than the one specified in this manual. In case of using a paper roll other than the one specified, there is a case the print quality and reliability may not be guaranteed.
iDP-3210 User ’ s Manual CITIZEN 24 Cautions : In case the slack of paper remains, remove the slack by rolling up the roll paper. In case the p aper is tilting, keep pressing FEED switch after closing printer cover. Then, this tilting is automatically corrected.
iDP-3210 User ’ s Manual CITIZEN 25 4.5 How to Remove Remaining Roll Paper (1) Open the printer co ver. (2) Holding the paper guide, pull it in the arrowed direction. The platen roller is detached from the print head and the remaining paper can be pulled out.
iDP-3210 User ’ s Manual CITIZEN 26 Caution : Since print head and motor are hot, do not carry out this action right after printing. In case of moving the head springs, do not move it beyond the removable range of the springs.
iDP-3210 User ’ s Manual CITIZEN 27 4.7 Canceling Cutter Lock (1) As referring to "4.6 Removing Paper Jam", remove the roll paper remains inside the paper c ourse. (2) Press the FEED switch. The auto cutter performs initialization, returning the blade to home position and canceling alarm state.
iDP-3210 User ’ s Manual CITIZEN 28 4.8 Cleaning Print Head (1) As referring to "4.6 Removing Paper Jam ” , remove the platen roller unit. (2) Using a cotton pud containing ethyl alcohol, wipe off dust, etc. on the surface of the surface of the head.
iDP-3210 User ’ s Manual CITIZEN 29 4.9 OPERATION PANEL AND DISPLAY OF ERROR (1) POWER LAMP (Green) With power switch is turned ON, this lamp lights up. Further, when "Memory Check Error" has occurred, this lamp lights up, too. (2) ERROR LAMP (Red) Error details are indicated by lighting or blinking state as follows.
iDP-3210 User ’ s Manual CITIZEN 30 Details of error Cover open : When printer cover is opened, printer cover open sensor detects the cover opening and has ERROR LED illuminate, then stops printing operation. But, depending on dip switch setting, paper feed can be performed when printer cover is opened.
iDP-3210 User ’ s Manual CITIZEN 31 5 Dip Switch Setting 5.1 Location of Dip Switch (1) Turn OFF the power switch. (2) Remove the rear cover. (Remove it by taking off two screws at the bottom and turning the cover in the arrowed direction.
iDP-3210 User ’ s Manual CITIZEN 32 5.2 Dip Switch Setting DS1 FUNCTION ON OFF FACTORY SETTING -1 Paper cutter Enabled Disabled ON -2 Cover open Disabled Enabled OFF -3 CR switching LF activate Ignored OFF -4 Unused OFF -5 Print columns 44 columns 42 columns ON -6 International Characters OFF -7 International Characters See the table below.
iDP-3210 User ’ s Manual CITIZEN 33 6. INTERFACE (Connecting with Peripheral Equipment) 6.1 Parallel Interface 6.1.1 Specifications Data input method : 8 bit parallel signal (DATA 1 - 8) Control sig.
iDP-3210 User ’ s Manual CITIZEN 34 6.1.3 I/O SIGNALS (1) Input Signals to the Printer l DATA : 8-bit parallel signal (positive logic) l STB : Strobe signal to read 8-bit data (negative logic) l RESET : Signal to reset the entire printer (negative logic) 1m sec or more (2) Output Signals from Printer l ACK : An 8 bit data request signal.
iDP-3210 User ’ s Manual CITIZEN 35 6.1.4 Electrical Characteristics (1) Input Signal Level All the input signals are at C-MOS level. "HIGH" level : 4.0V MIN "LOW" level : 1.0V MAX (2) Output Signal Level All the output signals are at C-MOS level.
iDP-3210 User ’ s Manual CITIZEN 36 6.1.5 TIMING CHART (1) Data Input and Printing Timing T1, T2, T3 : 0.5 λ s MIN T4 : 270 ns MAX T5 : 2.3 λ s TYP T6 : 500 ms MIN (On supplying power) 6.1.6 Data Receiving Control When BUSY signal is "LOW", data from the host c an be received.
iDP-3210 User ’ s Manual CITIZEN 37 6.2 Serial Interface 6.2.1 Specifications (1) Data transfer system: Asynchronous (2) Baud rates 150, 300, 600, 1200, 2400, 4800, 9600, 19200 bps (Selectable by us.
iDP-3210 User ’ s Manual CITIZEN 38 6.2.2 Connector ’ s Pin Configurations No. SIGNAL NAME I/O FUNCTION 1 FG Frame Grand 7 GND Signal GND 3 RD Input Receiving data 20 DTR Output Printer BUSY signa.
iDP-3210 User ’ s Manual CITIZEN 39 6.2.3 I/O SIGNALS (1) RD Serial receiving data signa l. On occurrence of framing error, overrun error, or parity error, the data is printed as "?". (2) DTR When this signal is READY, write data or a command.
iDP-3210 User ’ s Manual CITIZEN 40 6.2.4 Data Configuration ------- à t Mark Space 1 2 3 1. Start bit 2. Data bit (+ parity bit) 3. Stop bit ( 1 or more ) (1) Start Bit In 1/2 bit from the mark-to-space starting edge, state is read once again. When "space" state is confirmed, it is recognized as the start bit.
iDP-3210 User ’ s Manual CITIZEN 41 6.2.5 Error Detection Parity, framing, and overrun are detected. On detection of any error, the data are stored in the buffer as "?". (1) Framing Error With "space" state having been detected on detection of a stop bit, error takes place.
iDP-3210 User ’ s Manual CITIZEN 42 6.2.8 ELECTRICAL CHARACTERISTICS (1) RS-232C Circuit Input (RD, DSR) (Printer Side) (Host Side) Equivalent to Max 232 RD Mark = <-8V> : Stop bit Space = <.
iDP-3210 User ’ s Manual CITIZEN 43 7 . Drawer Kickout Connector 7.1 Specifications (1) Drawer-Kick Drive Signal Pulses specified by ESCp are output. Also, SW(+) state, in parallel interface, can be observed by Pin 34 of the interface c onnector and, in serial interface, by ESC u command.
iDP-3210 User ’ s Manual CITIZEN 44 8 POWER SUPPLY CONNECTOR SPECIFICATIONS This is the connector for power supply from exclusive AC Adapter. Connector ’ s Pin Configurations No.
iDP-3210 User ’ s Manual CITIZEN 45 9 PRINT CONTROL FUNCTION 9.1 Command List CONTROL CODE FUNCTION PAGE 1 HT Horizontal tab command 2 CR Print command 3 LF Printing and paper feed 4 ESC SP Setting .
iDP-3210 User ’ s Manual CITIZEN 46 9.2 Command Details (1) Horizontal Tab Command (HT) Code : (09)h Shifts the printing position to the next horizontal tab position. The horizontal tab position is set by ESC D. Initial setting of the horizontal tab position is in 9th, 17th, 25th, 33rd, 41st columns.
iDP-3210 User ’ s Manual CITIZEN 47 (5) Specifying Collectively the Print Mode (ESC ! n) Code: [1Bh] + [21h] + n ≤ * {0 ≤ n ≤ FF} The data is described in Hex code.
iDP-3210 User ’ s Manual CITIZEN 48 (7) Defining Download Character (ESC & s n m a (D1D2 - Dn) Code: [1B]h + [26]h + s +n +m +a + Dn * {s = 02} {20 (Hex) ≤ n ≤ 7E (Hex)} {20 (Hex) ≤ m ≤ 7E (Hex)} {0 ≤ a ≤ 0A (Hex)} Defines the font of download characters of alphanumeric characters.
iDP-3210 User ’ s Manual CITIZEN 49 (8) Specifying the Bit Image Mode (ESC * m n1 n2 D1 - Dn) Code : [1B]h + [2A]h + m + n1 + n2 + Dn * {m= bit image mode (See the table below.)} {0 ≤ n1 ≤ FF} {0 ≤ n2 ≤ 02} Data is described in Hex code. According to the bit image mode assigned in m, prints data in the bit image.
iDP-3210 User ’ s Manual CITIZEN 50 (9) Specifying/ Canceling Underline (ESC - n) Code: [1B]h + [2D]h + n * {0 ≤ n ≤ 02} Data is described in Hex code. Specifying/canceling an underline. l An underline is attached to the full character width. It is, however, not attached to the part having been horizontal tab command.
iDP-3210 User ’ s Manual CITIZEN 51 (14) Specifying/canceling highlighting (ESC E n) Code : [1B]h + [45]h + n * {0 ≤ n ≤ FF} Data is described in Hex code. Specifying/canceling the highlighted characters. l "n" is valid only for the lowest bit (n0).
iDP-3210 User ’ s Manual CITIZEN 52 (17) Selecting International Characters (ESC R n) Code : [1B]h + [52]h + n * {0 ≤ n ≤ 0A) Data is described in Hex code. Selecting international characters. l Depending on the value of n, following character sets are specified.
iDP-3210 User ’ s Manual CITIZEN 53 (20) Enabling/Disabling Panel Switch (ESC c 5 n) Code : [1B]h + [63]h + [35]h + n * {0 ≤ n ≤ FF} Data is described in Hex code. Selecting the paper feed switch valid/invalid. l "n" is valid only in the lowest bit (n0).
iDP-3210 User ’ s Manual CITIZEN 54 (23) Transmitting the printer status (ESC v) Code : [1B]h + [76]h Current printer status is transmitted.. l Status sent out consists of 1 byte whose content is as in the table below.
iDP-3210 User ’ s Manual CITIZEN 55 (25) specifying/Canceling Inverted Characters Code : [1B]h + [7B]h + n * {0 ≤ n ≤ FF} Data is described in Hex code. Specifying/canceling inverted characters. l "n" is valid only for the lowest bit (n0).
iDP-3210 User ’ s Manual CITIZEN 56 (26) Specifying/Canceling 90°-right- turned Characters (ESC V n) Code : [1B]h + [56]h + n * {0 ≤ n ≤ 1} Data is described in Hex code. Specifyi ng/canceling characters 90°-right- turned character. l No underlines are attached to 90°-right- turned characters .
iDP-3210 User ’ s Manual CITIZEN 57 (29) Bar Code Printing (GS k n Dn NUL) Code : [1D]h + [6B]h + n + Dn + [00]h * {0 ≤ n ≤ 7} Data are described in Hex code. Specifying a type of bar code and printing b ar codes. l The beginning of line is considered as the next printing start position.
iDP-3210 User ’ s Manual CITIZEN 58 (32) Selecting Printing Position of HRI Characters (GS H n) Code : [1d]H + [48]H + N * {0 ≤ n ≤ 3} Data is described in Hex code. Selecting printing position of HRI characters for printing bar codes. l "n" means the followings.
iDP-3210 User ’ s Manual CITIZEN 59 (35) Starting / Ending Macro Definition (GS :) Code : [1D]h + [3A]h Specifying starting / ending mac ro definition. Maximum content available for macro definition is 2048 bytes. A portion exceeding 2048 bytes is not defined.
iDP-3210 User ’ s Manual CITIZEN 60 (38) Data Input Control (ESC = n) Code : [1B]h + [3D]h + n * {0 ≤ n ≤ FF} Data is described in Hex code. Selecting equipmen t in which data input from the host is effective.
iDP-3210 User ’ s Manual CITIZEN 61 10 CHARACTER CODE TABLE 10.1 International (IBM Character # 2).
iDP-3210 User ’ s Manual CITIZEN 62 10.2 International Character Code Table.
iDP-3210 User ’ s Manual CITIZEN 63 A pp endix 1 Outline Drawing 1.1Outler Dr a wing of Printer (Model : iDP-3210).
iDP-3210 User ’ s Manual CITIZEN 64 1.2Outer Drawing of AC Adapter (Model : 30AD).
iDP-3210 User ’ s Manual CITIZEN 65 Appendix 2 Block Diagram.
Ein wichtiger Punkt beim Kauf des Geräts Citizen Systems iDP-3210 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Citizen Systems iDP-3210 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Citizen Systems iDP-3210 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Citizen Systems iDP-3210 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Citizen Systems iDP-3210 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Citizen Systems iDP-3210 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Citizen Systems iDP-3210 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Citizen Systems iDP-3210. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Citizen Systems iDP-3210 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
