Benutzeranleitung / Produktwartung PA-4T des Produzenten Cisco Systems
Zur Seite of 76
170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Cisco Systems, Inc. Corporate Headquarters Tel: 800 553-NETS (6387) 408 526-4000 Fax: 408 526-4100 P A-4T+ Synchronous Ser ial P .
Access Registrar, AccessPath, Any to Any, AtmDirector, CCDA, CCDE, CCDP, CCIE, CCNA, CCNP, CCSI, CD-PAC, the Cisco logo, Cisco Certified Internetwork Expert logo, CiscoLink , the Cisco Management Conn.
CHAPTER Overview 1-1 1 Ov er vie w This chapter describes the P A-4T+ port adapter and describes its LEDs, cables, and receptacles. This chapter contains the following sections: • Port Adapter Overv.
Port Adapter Overview PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 1-2 Figure 1-2 P A-4T P or t Adapter—Faceplate View The following e xample of the show diag slot command s.
Overview 1-3 Synchronous Serial Overview The following e xample of the show diag slot command shows a P A-4T+ in port adapter slot 1 in a Cisco 7200 series or a cisco uBR7200 series router: Router# show diag 1 Slot 1: Mx serial port adapter, 4 ports Port adapter is analyzed Port adapter insertion time 02:19:52 ago Hardware revision 1.
Serial Interface Specifications PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 1-4 EIA/TIA-449. Like EIA/TIA-449, EIA-530 refers to the electrical specifications of EIA/TIA-422 and EIA/TIA-423. The specification recommends a maximum speed of 2 Mbps.
Overview 1-5 Cables and Pinouts T able 1-1 Standards f or T ransmission Speed V ersus Distance Balanced dri vers allow EIA/TIA-449 signals to tra vel greater distances than EIA/TIA-232. The recommended distance limits for EIA/TIA-449 sho wn in T able 1-1 are also v alid for V .
Cables and Pinouts PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 1-6 • EIA/TIA-449: DTE mode with a 37-pin D-shell plug (CAB-449MT=); DCE mode with a 37-pin D-shell receptacle (CAB-449C=). • V .35: DTE mode or DCE mode with a 34-pin W inchester-type V .
Overview 1-7 PA-4T+ Receptacles and Cables EIA/TIA-232 Connections The router end of all EIA/TIA-232 adapter cables is a high-density 60-pin plug. The network end of the adapter cable is a standard 25-pin D-shell connector (kno wn as a DB-25) that is commonly used for EIA/TIA-232 connections.
Cables and Pinouts PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 1-8 EIA/TIA-449 Connections The router end of all EIA/TIA-449 adapter cables is a high-density 60-pin plug. The network end of the adapter cable provides a standard 37-pin D-shell connector , which is commonly used for EIA/TIA-449 connections.
Overview 1-9 PA-4T+ Port Adapter Cable Pinouts X.21 Connections The router end of all X.21 adapter cables is a high-density 60-pin plug. The network end of the adapter cable is a standard DB-15 connector . Figure 1-7 shows the connectors at the netw ork end of the X.
Cables and Pinouts PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 1-10 T able 1-2 EIA/TIA-232 Adapter Cable Signals DTE Cable (CAB-232MT=) DCE Cable (CAB-232FC=) Router End, HD 1 60-P osition Plug 1 HD = high density.
Overview 1-11 PA-4T+ Port Adapter Cable Pinouts T able 1-3 Intermediate Adapter Cable Signals (f or Connecting a P A-4T+ to a NEC - NEXTST AR 1E Model C4969 MD/SAC Unit) Router (DTE) End, DB-25 Recept.
Cables and Pinouts PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 1-12 T able 1-4 EIA/TIA-449 Adapter Cable Signals DTE Cable (CAB-449MT=) DCE Cable (CAB-449C=) Router End, HD 1 60-P osition Plug 1 HD = high density.
Overview 1-13 PA-4T+ Port Adapter Cable Pinouts T able 1-5 EIA-530 DTE Adapter Cable Signals (CAB-530MT=) Router End, HD 1 60-P osition Plug 1 HD = high density.
Cables and Pinouts PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 1-14 T able 1-6 V .35 Adapter Cable Signals DTE Cable (CAB-V35FT= or CAB-V35MT=) DCE Cable (CAB-V35FC= or CAB-V35MC=) Router End, HD 1 60-P osition Plug 1 HD = high density.
Overview 1-15 LEDs LEDs The P A-4T+ contains the enabled LED, standard on all port adapters, and one status LED for each port. After system initialization, the enabled LED goes on to indicate that the P A-4T+ has been enabled for operation. (The LEDs are shown in Figure 1-9.
LEDs PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 1-16 If any of the abo ve conditions are not met, or if the initialization fails for other reasons, the enabled LED will not go on. T able 1-8 lists port LED status indications.
Preface v Pref ace This preface describes the objecti ves and organization of this document and e xplains how to find additional information on the P A-4T+ port adapter and other Cisco products and services.
Document Organization PA-4T+ Synchronous Serial Port Adapter Installation and Configuration vi Document Organization This document is organized into the follo wing chapters: Related Documentation Y ou.
Preface vii Cisco Connection Online • For hardware installation and maintenance information on the Cisco 7100 series routers, refer to the Cisco 7100 Series VPN Router Configuration Guide publicati.
Documentation CD-ROM PA-4T+ Synchronous Serial Port Adapter Installation and Configuration viii Y ou can access CCO in the following ways: WWW : http://www .cisco.com WWW : http://www-europe.cisco.com WWW : http://www-china.cisco.com T elnet: cco.cisco.
CHAPTER Preparing for Installation 2-1 2 Prepar ing f or Installation This chapter describes the general equipment, safety , and site preparation requirements for installing the P A-4T+ port adapter .
Software and Hardware Requirements PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 2-2 Software and Har dware Requirements lists the minimum Cisco IOS software release required to use the P A-4T+ port adapter in supported router platforms.
Preparing for Installation 2-3 Software and Hardware Requirements Note The minimum recommended VIP2 model is a VIP2-15..
Safety Guidelines PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 2-4 Safety Guidelines This section provides safety guidelines that you should follo w when working with any equipment that connects to electrical power or telephone wiring.
Preparing for Installation 2-5 Electrical Equipment Guidelines Adv arsel Dette varselsymbolet betyr f are. Du befinner deg i en situasjon som kan føre til personskade.
FCC Class B Compliance PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 2-6 Pre v enting Electrostatic Discharge Damage Electrostatic discharge (ESD) damage, which can occur when electronic cards or components are improperly handled, results in complete or intermittent failures.
Preparing for Installation 2-7 FCC Class B Compliance • Mov e the equipment farther away from the tele vision or radio. • Plug the equipment into an outlet that is on a dif ferent circuit from the television or radio.
FCC Class B Compliance PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 2-8.
CHAPTER VIP2 and the PA-4T+ Port Adapter 3-1 3 VIP2 and the P A-4T+ P or t Adapter This chapter provides information on the P A-4T+ port adapter and its use in the VIP2 in Cisco 7000 series and Cisco 7500 series routers.
Installation Overview PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 3-2 Figure 3-1 VIP2-15 or VIP2-40 with a P A-4T+ in P or t Adapter Slot 1 Note Port adapters hav e a handle attached, but this handle is not sho wn to allow a full vie w of detail on each port adapter’ s faceplate.
VIP2 and the PA-4T+ Port Adapter 3-3 Removing a Port Adapter Remo ving a P or t Adapter This section provides the standard procedures for remo ving a port adapter on the VIP2. Depending on the circumstances, you might need to install a new port adapter on a VIP2 motherboard or replace a failed port adapter in the field.
Installing a Port Adapter PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 3-4 Figure 3-3 Location of P or t Adapter Screw—P ar tial P or t Adapter View Step 5 Remov e the screw that secures the port adapter (or blank port adapter).
VIP2 and the PA-4T+ Port Adapter 3-5 Installing a Port Adapter Figure 3-5 Aligning a P or t Adapter in a P or t Adapter Slot Step 2 Before you insert the new port adapter in its slot, v erify that the port adapter carrier is between the upper and lower slot edges, as sho wn in Figure 3-5.
Installing a Port Adapter PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 3-6 Figure 3-6 P or t Adapter Installed in a P or t Adapter Slot—Partial P ort Adapter View Step 4 Replace the screw in the rear of the port adapter slot.
CHAPTER Cisco 7200 Series and the PA-4T+ Port Adapter 4-1 4 Cisco 7200 Ser ies and the P A-4T+ P or t Adapter This chapter provides information on the P A-4T+ and its use in the Cisco 7200 series routers.
Removing a Port Adapter PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 4-2 When a port adapter slot is not in use, a blank port adapter must fill the empty slot to allo w the router to conform to EMI emissions requirements and to allow proper air flo w across the port adapters.
Cisco 7200 Series and the PA-4T+ Port Adapter 4-3 Installing a Port Adapter Figure 4-3 Handling a P or t Adapter Step 6 Place the port adapter on an antistatic surface with its components facing upw ard, or in a static shielding bag. If the port adapter will be returned to the factory , immediately place it in a static shielding bag.
Installing a Port Adapter PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 4-4 Step 5 W ith the port adapter halfway in the slot, connect all required cables to the port adapter .
CHAPTER Cisco uBR7200 Series and the PA-4T+ Port Adapter 5-1 5 Cisco uBR7200 Ser ies and the P A-4T+ P or t Adapter This chapter provides information on the P A-4T+ port adapter and its use on Cisco uBR7200 series univ ersal broadband routers.
Removing a Port Adapter PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 5-2 Note The Cisco uBR7200 series supports online insertion and remov al (OIR); therefore, you do not hav e to power do wn the router when removing and replacing a P A-4T+.
Cisco uBR7200 Series and the PA-4T+ Port Adapter 5-3 Removing a Port Adapter • For the Cisco uBR7223, place the port adapter le ver in the unlocked position.
Installing a Port Adapter PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 5-4 Step 6 Place the port adapter on an antistatic surface with its components facing upw ard, or in a static shielding bag. If the port adapter will be returned to the factory , immediately place it in a static shielding bag.
Cisco uBR7200 Series and the PA-4T+ Port Adapter 5-5 Installing a Port Adapter Note If the retention clip does not slide up to the locked position, the port adapter is not completely seated in the midplane. Carefully pull the port adapter halfway out of the slot, reinsert it, and slide the port adapter lev er up to the locked position.
Installing a Port Adapter PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 5-6 This completes the procedure for installing a port adapter in a Cisco uBR7200 series router . Proceed to Chapter 7, “Installing the P A-4T+ Interf ace Cables, ” to connect the necessary cables to your port adapter .
CHAPTER Cisco 7100 Series and the PA-4T+ Port Adapter 6-1 6 Cisco 7100 Ser ies and the P A-4T+ P or t Adapter This chapter provides information on the P A-4T+ port adapter and its use in the Cisco 7100 series routers.
Removing a Port Adapter PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 6-2 Figure 6-2 Cisco 7140 Series Router—P or t Adapter Slot 4 Location Depending on your circumstances, you might need to install a new port adapter in a Cisco 7100 series router or replace a failed port adapter in the field.
Cisco 7100 Series and the PA-4T+ Port Adapter 6-3 Installing a Port Adapter Figure 6-3 Handling a P or t Adapter Step 6 Place the port adapter on an antistatic surface with its components facing upw ard, or in a static shielding bag. If the port adapter will be returned to the factory , immediately place it in a static shielding bag.
Installing a Port Adapter PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 6-4 Figure 6-4 Aligning the Single-Width P or t Adapter Between the Slot Guides Step 7 W ith the port adapter halfway in the slot, connect all required cables to the port adapter .
CHAPTER Installing the PA-4T+ Interface Cables 7-1 7 Installing the P A-4T+ Interf ace Cab les T o continue your P A-4T+ port adapter installation, you must install the port adapter cables and configure the P A-4T+ interfaces. The instructions that follo w apply to all supported platforms.
Replacing PA-4T+ Port Adapter Cables PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 7-2 Caution Serial interface cables must be attached correctly or damage to the cable plug will result. Attempting to force a cable plug on the 60-pin receptacle can damage the plug.
Installing the PA-4T+ Interface Cables 7-3 Replacing PA-4T+ Port Adapter Cables Follo wing is an example of the show contr ollers cbus command for a VIP2 that sho ws an interface port (3/1/0) that has an EIA/TIA-232 DTE cable attached: Router# show controllers cbus 3/1/0 slot3: VIP2, hw 2.
Replacing PA-4T+ Port Adapter Cables PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 7-4 For a Cisco 7100 series, Cisco 7200 series, or Cisco uBR7200 series router , use the follo wing commands: Router# configure terminal Enter configuration commands, one per line.
CHAPTER Configuring the PA-4T+ Interfaces 8-1 8 Configur ing the P A-4T+ Interf aces T o continue your P A-4T+ port adapter installation, you must install the port adapter cables and configure the P A-4T+ interfaces. The instructions that follo w apply to all supported platforms.
Identifying Port Adapter Slot and PA-4T+ Interface Port Numbers PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 8-2 The system prompt for the privile ged lev el ends with a pound sign (#) instead of an angle bracket (>).
Configuring the PA-4T+ Interfaces 8-3 Cisco 7200 Series and Cisco uBR7200 Series Ports Figure 8-1 P A-4T+ Interface P or t Address Example—Cisco uBR7246 Figure 8-2 shows the interface ports of a P A-4T+ in slot 2 of the Cisco uBR7200 series.
Identifying Port Adapter Slot and PA-4T+ Interface Port Numbers PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 8-4 VIP2 P or ts In the router, physical port addresses specify the actual physical location of each interf ace port on the router interface processor end.
Configuring the PA-4T+ Interfaces 8-5 Cisco 7100 Series Ports Cisco 7100 Series P or ts In Cisco 7100 series routers, the s lot number is the location in the chassis where the interface resides and the port number is the physical port. Interfaces in the Cisco IOS software are identified by a type, slot number , and port number .
Shutting Down an Interface PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 8-6 Step 2 At the privile ged-lev el prompt, enter configuration mode and specify that the console terminal will be the source of the configuration subcommands as follows: Router# configure terminal Enter configuration commands, one per line.
Configuring the PA-4T+ Interfaces 8-7 Shutting Down an Interface For a Cisco 7200 series, Cisco uBR7200 series, or Cisco 7100 series router , use the follo wing example: Router# show interfaces serial.
Performing a Basic Configuration PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 8-8 P erf orming a Basic Configuration Follo wing are instructions for a basic interface configuration: enabling an interface, specifying IP routing, and setting up external timing on a DCE interface.
Configuring the PA-4T+ Interfaces 8-9 Configuring Timing (Clock) Signals Step 9 When you hav e included all of the configuration subcommands to complete the configuration, press Ctrl-Z (hold down the Contr ol key while you press Z ) or enter end to exit configuration mode and return to the EXEC command interpreter prompt.
Configuring Timing (Clock) Signals PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 8-10 Note Cisco IOS Release 11.2(7a)P or later , or 11.
Configuring the PA-4T+ Interfaces 8-11 Setting the Clock Rate When the P A-4T+ interface is a DTE, the in vert-txc command in verts the TxC signal it recei ves from the remote DCE. When the P A-4T+ interface is a DCE, this command in verts the clock signal to the remote DTE port.
Configuring Half-Duplex and Binary Synchronous Communications PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 8-12 Configuring CRCs Cyclic redundancy check (CRC) is an error -checking technique that uses a calculated numeric value to detect errors in transmitted data.
Configuring the PA-4T+ Interfaces 8-13 Configuring Half-Duplex Configuring Half-Duplex Use the half-duplex command to configure P A-4T+ interfaces for half-duplex mode; full-duple x mode is the default for lo w-speed serial interfaces.
Checking the Configuration PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 8-14 T able 8-1 Half-Duplex Timer Default Settings Configuring Bisync T o configure P A-4T+ interface.
Configuring the PA-4T+ Interfaces 8-15 Using show Commands to Display Interface Information Using show Commands to Displa y Interf ace Inf ormation T o display information about a specific interface,.
Checking the Configuration PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 8-16 The following e xample of the show interfaces serial slot/port command on a Cisco 7200 series, Cis.
Configuring the PA-4T+ Interfaces 8-17 Using show Commands to Display Interface Information The show version (or sho w hardwar e ) command displays the configuration of the system hardware (the number of each port adapter type installed), the software version, the names and sources of configuration files, and the boot images.
Checking the Configuration PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 8-18 VIP2 show interf aces Command Follo wing are examples of how the show interfaces [ type slot/port-adapter/port ] command displays status information (including the physical slot and port address) for the interfaces you specify .
Configuring the PA-4T+ Interfaces 8-19 Using show Commands to Display Interface Information The following e xample of the show interfaces serial slot/port-adapter/port command sho ws all of the inform.
Checking the Configuration PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 8-20 The show version (or sho w hardwar e ) command displays the configuration of the system hardware (the number of each interface processor type installed), the software v ersion, the names and sources of configuration files, and the boot images.
Configuring the PA-4T+ Interfaces 8-21 Using ping and loopback Commands Use the show diag command to vie w all the interface types installed in your system.
Checking the Configuration PA-4T+ Synchronous Serial Port Adapter Installation and Configuration 8-22 Follo wing is an example of a successful ping command to a remote server with the address 10.10.10.10: Router# ping 10.10.10.10 <Return> Type escape sequence to abort.
Ein wichtiger Punkt beim Kauf des Geräts Cisco Systems PA-4T (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Cisco Systems PA-4T noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Cisco Systems PA-4T - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Cisco Systems PA-4T reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Cisco Systems PA-4T erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Cisco Systems PA-4T besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Cisco Systems PA-4T verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Cisco Systems PA-4T. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Cisco Systems PA-4T gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
