Benutzeranleitung / Produktwartung NPE-225 des Produzenten Cisco Systems
Zur Seite of 226
Americas Headquarters Cisco Systems, In c. 170 West Tasman Drive San Jose, CA 951 34-1706 USA http://www.ci sco.com Tel: 408 526-4000 800 553-NETS (638 7) Fax: 408 527-0883 Netw ork P r ocessing Engin.
THE SPECIFICATION S AND INFORMATION REGARDING THE P RODUCTS IN TH IS MANUAL AR E SUBJECT TO CHANGE WITHOUT NOT ICE. ALL STATEMENTS , INFORMATION, AND RECOMMENDATI ONS IN THI S MANUAL ARE BE LIEVED TO BE A CCURATE BUT ARE PRESENTED WI THOUT WARRANTY OF ANY KIND, EX PRESS OR IMPLIED.
iii Network Processing Engin e and Network Services Engine Installation and Configuration OL-4448-12 CONTENTS Preface i Document Revision History i-i Objectives i-ii Organization i-ii Related Document.
Contents iv Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 System Management Fu nctions 3-4 Terms and Acronyms 3-4 NPE-300 and NPE-400 Memory Infor.
Contents v Network Processing Engin e and Network Services Engine Installation and Configuration OL-4448-12 Bandwidth Requirements 6-3 Components 6-3 Interfaces 6-4 LEDs 6-5 CompactFlash Disk 6-6 USB .
Contents vi Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Installing an SFP Module—NPE-G2 7-20 Installing a GBIC—NPE-G1 7-23 Replacing the DIM.
Contents vii Network Processing Engin e and Network Services Engine Installation and Configuration OL-4448-12 Configuring the Interface Transmission and Speed Modes 7-57 Sample Configuration for the G.
Contents viii Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Removing the NPE or NSE 9-9 Removing and Installin g Memory 9-11 Removing DRAM SIMMs 9.
Contents ix Network Processing Engin e and Network Services Engine Installation and Configuration OL-4448-12 Replacing a Power Supply in a Cisco 720 0 Series Router 10-15 Fiber Optic Cleaning Informat.
Contents x Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12.
i Network Processing Engin e and Network Services Engine Installation and Configuration OL-4448-12 Preface This preface describes th e objecti ves and or ganization of this document and e xplains ho w to f ind additional informati on on related products and servi ces.
ii Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Preface Objectives Objectives This document incl udes an ov ervie w of each netw or k processing .
iii Network Processing Engin e and Network Services Engine Installation and Configuration OL-4448-12 Preface Related Documentation Related Documentation Y our router and the Ci sco IOS software runnin.
iv Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Preface Obtaining Documentation an d Submitting a Se rvice Request • Cisco 7200 Series Router s Documentation Roadmap at http://www .cisco.com/en/US/docs/routers/ 7200/ roadmaps/7200_seri es_doc_roadmap/3512.
CH A P T E R 1-1 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 1 NPE-100, NPE-150, and NPE-200 Overview This chapter describes the netwo rk processi.
1-2 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 1 NPE-100, NPE-150, and NPE-200 Overview NPE-100, NPE-150, and NPE-200 Desc ription and Overview • The network processing engine maintains and e xec utes the system management functions for the Cisco uBR7200 series routers.
1-3 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 1 NPE-100, NPE-150, and NPE-200 Overview NPE-100, NPE-150, and NPE-200 Description and Ove.
1-4 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 1 NPE-100, NPE-150, and NPE-200 Overview NPE-100, NPE-150, and NPE-200 Desc ription and .
1-5 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 1 NPE-100, NPE-150, and NPE-200 Overview NPE-100, NPE-150, and NPE-200 Description and Ove.
1-6 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 1 NPE-100, NPE-150, and NPE-200 Overview NPE-100, NPE-150, and NPE- 200 Memory Informati.
1-7 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 1 NPE-100, NPE-150, and NPE-200 Overview NPE-100, NPE-150, and NP E-200 Memory Information NPE-100 Memory Information Ta b l e 1-1 pro vides information about memo ry specificat ions.
1-8 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 1 NPE-100, NPE-150, and NPE-200 Overview NPE-100, NPE-150, and NPE- 200 Memory Information NPE-200 Memory Information Ta b l e 1-5 prov ides information about memory specif ication s.
CH A P T E R 2-1 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 2 NPE-175 and NPE-225 Overview This chapter describes the netw ork processing engin e.
2-2 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 2 NPE-175 and NPE-225 Overview NPE-175 and NPE-225 Desc ription and Overview Components .
2-3 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 2 NPE-175 and NPE-225 Overview NPE-175 and NPE-225 Description and Overview Figur e 2-2 NP.
2-4 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 2 NPE-175 and NPE-225 Overview NPE-175 and NPE-225 Desc ription and Overview • Boot R .
2-5 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 2 NPE-175 and NPE-225 Overview NPE-175 and NPE-225 Memory Information • SRAM—static random-access memory • Unified cache— Instruction cache and data cache are combined.
2-6 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 2 NPE-175 and NPE-225 Overview NPE-175 and NPE-225 Memory Information Ta b l e 2-2 NPE-1.
CH A P T E R 3-1 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 3 NPE-300 and NPE-400 Overview This chapter describes the netw ork processing engin e.
3-2 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 3 NPE-300 and NPE-400 Overview NPE-300 and NPE-400 Desc ription and Overview NPE-300 and.
3-3 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 3 NPE-300 and NPE-400 Overview NPE-300 and NPE-400 Description and Overview Figur e 3-2 NP.
3-4 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 3 NPE-300 and NPE-400 Overview NPE-300 and NPE-400 Desc ription and Overview • Upgradable memory modules The NPE-300 and NPE-400 use SDRAM fo r storing all pack ets receiv ed or sent from netw ork interfaces.
3-5 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 3 NPE-300 and NPE-400 Overview NPE-300 and NPE-400 Memory Information • Primary , secondary , tertiary cache—Hierarchical cache memory storage based on th e proximity of the cache to the core of the processor .
3-6 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 3 NPE-300 and NPE-400 Overview NPE-300 and NPE-400 Memory Information cisco 7206VXR (NPE400) processor (revision 0xFF) with 122880K/8192K bytes of memory.
3-7 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 3 NPE-300 and NPE-400 Overview NPE-300 and NPE-400 Memory Information 32 MB 4 + 128 MB U45 and U44 or U45 2 64-MB DIMMs or 1 128-MB DIMM MEM-SD-NPE-64MB MEM-SD-NPE-128MB 32 MB 4 + 256 MB U45 and U44 2 128-MB DIMMs MEM-SD-NPE-256MB 1.
3-8 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 3 NPE-300 and NPE-400 Overview NPE-300 and NPE-400 Memory Information.
CH A P T E R 4-1 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 4 NSE-1 Overview This chapter describes the netw ork services engine (NSE-1) and cont.
4-2 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 4 NSE-1 Overvie w NSE-1 Description and Over view Note The NSE-1 is not supported in t he Cisco uBR7200 VXR series routers, e v en though it is physically capable of being insert ed into the routers.
4-3 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 4 NSE-1 Overview NSE-1 Description and Overview • System co ntroller The system controller provides hardware logi c to interconnect the processor , DRAM, and the PCI-based system backplane bus.
4-4 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 4 NSE-1 Overvie w NSE-1 Memory Information • Primary , secondary , tertiary cache—Hierarchical cache memory storage based on the p roximity of the cache to the core of the processor .
4-5 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 4 NSE-1 Overview NSE-1 Memory Information Secondary cache 256 KB — RM7000 processor , internal, unifi ed cache U22 T ertiary cache 2 MB (fixed) — RM7000 processo r , e xternal cache 2 U7, U9, U12, U14, U17 1.
4-6 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 4 NSE-1 Overvie w NSE-1 Memory Information.
CH A P T E R 5-1 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 5 NPE-G1 Overview This chapter de scribes the NPE-G1 an d contains the follo w ing se.
5-2 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 5 NPE-G1 Overview NPE-G1 Description and Overview NPE-G1 Description and Overview This section contains information about the NPE-G1 components and the system management functio ns.
5-3 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 5 NPE-G1 Overview NPE-G1 Description and Overview Components Figure 5-1 illustrates the NPE-G1 an d its major components.
5-4 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 5 NPE-G1 Overview NPE-G1 Description and Overview – Three Gigabit Ethernet interf aces (six ports: th ree GBI C [optical] and three RJ-45s [copper]).
5-5 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 5 NPE-G1 Overview NPE-G1 Description and Overview • Only one port per interf ace can be used at any one time. F or example, for in terface Gigabit Ethernet 0/1, either the RJ-45 port can be used o r the GBIC port, b ut not both.
5-6 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 5 NPE-G1 Overview NPE-G1 Description and Overview CompactFlash Disks are smaller in size than T ype 2 Flash Disks but pro vide the same Attachment (A T A) interface and eq uiv alent fun ctionality .
5-7 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 5 NPE-G1 Overview NPE-G1 Description and Overview T o remov e a CompactFlash Disk from the CompactFl ash Disk slot, complete the follo wing steps: Step 1 Press the ejector button on the slot.
5-8 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 5 NPE-G1 Overview NPE-G1 Description and Overview • The NPE-G1 uses no ban dwidth points, and wh en used with any I/O co ntroller , the I/O cont roller also uses no band width points.
5-9 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 5 NPE-G1 Overview NPE-G1 Memory Information • Primary and secondary cache—Hie rarchical cache memory storage based on the pr oximity of the cache to the core of the processor .
5-10 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 5 NPE-G1 Overview Connection Equipment and Specifications Connection Equipment and Spec.
5-11 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 5 NPE-G1 Overview Connection Equipme nt and Specifications Note T o comply with EMI EN550 22 Class B regulations, shi elded Ethernet cables must be used with the UBR7200-NPE-G1 in the Ci sco uBR7246VXR router .
5-12 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 5 NPE-G1 Overview Connection Equipment and Specifications Figur e 5-6 Fou r T wisted-P .
5-13 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 5 NPE-G1 Overview Connection Equipme nt and Specifications Figur e 5-8 Ether net/Fast Eth.
5-14 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 5 NPE-G1 Overview Connection Equipment and Specifications Figure 5-10 sho ws the simple x and duple x SC-type connectors on your multi mode or single-mode optical f iber cables.
5-15 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 5 NPE-G1 Overview Connection Equipme nt and Specifications Ta b l e 5-6 lists the a v ailable CWDM GBIC options. Ta b l e 5-7 pro vides cabling specifications for the GBICs that you install in Gigabit Ethernet devices.
5-16 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 5 NPE-G1 Overview Connection Equipment and Specifications Mode-Conditioning Patch Cord .
5-17 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 5 NPE-G1 Overview Connection Equipme nt and Specifications Figur e 5-1 1 Mo de Conditioni.
5-18 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 5 NPE-G1 Overview Connection Equipment and Specifications Note When connecting to an auxiliary port on a Cisco 7200 VXR router , the port will not function at baud rates higher than 19.
5-19 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 5 NPE-G1 Overview Connection Equipme nt and Specifications The Cisco 7200 series router s ship with a roll-ov er cable. Connection to a termi nal or a modem requires an RJ-45-to -DB-25 adapter, and possibl y a DB-25-to-DB9 adapter .
5-20 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 5 NPE-G1 Overview Fiber Optic Cleaning Information RJ-45 Auxiliary Port Signals and Pinouts Ta b l e 5-12 lists the RJ-45 auxil iary port signals for the NPE-G1.
CH A P T E R 6-1 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 6 NPE-G2 Overview This chapter de scribes the NPE-G2 an d contains the follo w ing se.
6-2 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview Software Requirements Software Requirements For minim um software release information, see the “Software Requirements” section on page 8-4 .
6-3 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Description and Overview Bandwidth Requirements The Gigabit Ethernet ports on the NPE-G2 do not use bandwidth point s, nor does the Fast Ethernet management port.
6-4 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Description and Overview • Cache memory The NPE-G2 has two levels of cache: primary and secondary cache that are internal to the microprocessor with secondary unifie d cache for data and instruction.
6-5 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Description and Overview • The port numbering for the interfaces on the NPE-G2 starts with 0/1 an d not with 0/0, as is typical for other interf ace cards.
6-6 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Description and Overview Figur e 6-3 NPE-G2 LEDs CompactFlash Disk The NPE-G2 has one CompactFlash Disk sl ot that uses CompactFlash Disks.
6-7 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Description and Overview CompactFlash Disks are smaller in size than T ype 2 Flash Disks but pro vide the same Attachment (A T A) interface and equi valent functionality .
6-8 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Description and Overview T o remov e a CompactFlash Disk from the CompactFl ash Disk slot, complete the follo wing steps: Step 1 Press the ejector button on the slot.
6-9 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Description and Overview Summary of Important NPE-G2 Information .
6-10 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Description and Overview Note The Gigabit Ethernet interf aces on the NPE-G2 do not support the Int er-Switch Link ( ISL) VLAN encapsulation protoc ol.
6-11 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specificat ions • SDRAM—synchronou s dynamic random-access memory . • SDRAM-f ixed—SDRAM of a f ixe d size or quantity; can be replaced, b ut not upgraded .
6-12 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specifications 2045K bytes of NVRAM.
6-13 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specificat ions Connection Equipment and.
6-14 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specifications Note W ith reference to the RJ-45 pinout in Ta b l e 6-7 , proper common-mod e line terminat ions should be used for the unused Cate gory 5 UTP cable pairs 4/5 and 7 /8.
6-15 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specificat ions Figur e 6-7 Fou r T wist.
6-16 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specifications Gigabit Ethernet SFP Co.
6-17 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specificat ions Ta b l e 6-8 pro vides SFP module specificat ions. The NPE-G2 supports single Gigabit Ethernet inte rfaces based on SFP technology .
6-18 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specifications Ta b l e 6-9 pro vides SFP port cabling specif ications. Ta b l e 6-10 pro vides SFP module po wer bu dget information.
6-19 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specificat ions Ta b l e 6-11 pro vides CWDM SFP module option informati on for the NPE-G2.
6-20 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specifications Figur e 6-1 1 Mo de-Con.
6-21 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specificat ions Note When connecting to an auxiliary port on a Cisco 7200 VXR router , the port will not function at baud rates higher than 19.
6-22 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specifications The Cisco 7200 series routers ship with a roll -ov er cable. Connection to a terminal or a modem requires an RJ-45-to -DB-25 adapter, and possibl y a DB-25-to-DB9 adapter .
6-23 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 6 NPE-G2 Overview Fiber Optic Cleaning Information RJ-45 Auxiliary Port Signals and Pinouts Ta b l e 6-15 list s the RJ-45 auxiliary port signals for the NPE-G2.
6-24 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview Fiber Optic Cleaning Information.
CH A P T E R 7-1 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 7 NPE-G1 and NPE-G2 Installation and Configuration Information This chapter pro vides.
7-2 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Preparing fo r an Upgrade Ti p Before you begin an y remov al or in stallation procedure, read Chapter 8, “Preparation f or Installation.
7-3 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Preparing for an Upgr ade.
7-4 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Copying the Configurati.
7-5 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Copying the Configuration File Step 3 Make sure you are at the privileg ed le v el of the EXEC command interpreter (check the system pro mpt for a pound sign [#]).
7-6 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Copying the Configuration File Step 4 Enter the copy startup-conf ig tftp command.
7-7 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Removing the Network Proc.
7-8 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Removing the Network Pr.
7-9 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Removing the Network Processin g Engine Note When poweri ng of f the router , wait a min imum of 30 seconds before po wering it on ag ain.
7-10 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Removing the Network P.
7-11 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Removing the Network Pro.
7-12 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Removing the Network P.
7-13 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Removing the Network Processin g Engine Step 5 Repeat this step for the –V lead and the ground lead.
7-14 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Removing the Network P.
7-15 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Removing the Network Pro.
7-16 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Removing the Network P.
7-17 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Removing the Network Pro.
7-18 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 .
7-19 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or NPE-G2 Installing a CompactFlash Disk Use the follo wing instruction s to install the CompactFlash Disk .
7-20 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 or NPE-G2 Caution Do not remov e a USB Flash memory module when a read o r write operation to the USB Flash memory module is in prog ress.
7-21 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or NPE-G2 Figur e 7 -9 T ypes of SFP Module Latches Note The SFP module must be installed before you connect the cables to it.
7-22 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 .
7-23 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or NPE-G2 Installing a GBIC—NPE-G1 Use the instructions in this sectio n to i nstall a GBIC in the NPE-G1.
7-24 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 or NPE-G2 Replacing the DIMM on the NPE-G2 T o replace the DIMM on the NPE-G2 , use the following instructions: Step 1 Locate the DIMM on th e NPE-G2.
7-25 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or NPE-G2 Figur e 7 -13 Installing or Remo ving the DIM M on the NPE-G2 Step 4 Gently insert a DIMM into the DIMM sock et.
7-26 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 .
7-27 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or NPE-G2 Figur e 7 -15 Removin g or Installing an SDRAM SODIMM Step 3 Remov e the SODIMM from the sock et.
7-28 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 or NPE-G2 Step 5 If the SODIMM appears misalign ed, carefully remov e it and reseat it in the so cket.
7-29 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or NPE-G2 Note The NPE-G1 or NPE-G2 is not fully seated in the rout er midplane until you ti ghten its capti ve installation sc rews.
7-30 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 or NPE-G2 Note Do not use the cable-manage ment bracket as a ha ndle for inserting and remo ving the NPE-G1 or NPE-G2 in the chassis .
7-31 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or NPE-G2 Step 1 Loosen the left and right capti ve installation scr ews on the NPE-G1 or NPE- G2.
7-32 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 .
7-33 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or.
7-34 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 or NPE-G2 Y ou have f inished in stalling the cable-management br ackets.
7-35 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or.
7-36 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 or NPE-G2 Figur e 7 -24 Connecting A C-Input P ower t o a Cisco 7200 VXR Router Step 4 Plug the A C po wer supply cable i nto the A C po wer source.
7-37 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or.
7-38 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 .
7-39 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or.
7-40 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 .
7-41 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or NPE-G2 This completes the steps for reconnecti ng DC-input po wer to a Cisco 7200 VXR router .
7-42 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 .
7-43 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or NPE-G2 Step 4 Connect the two -hole grounding lu g on the groundin g lead to the M5 gro unding receptacles with the M5 nuts.
7-44 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 .
7-45 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or.
7-46 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Enabling the Second Pr ocessor on the NPE-G1 Note When poweri ng on the router , wait a minimum of 30 seconds before po wering it of f again.
7-47 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Enabling the Second Processor o n the NPE-G1 • Upgrade the R OMmon. (The minimum R OMmon version is 12.
7-48 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Enabling the Second Pr ocessor on the NPE-G1 Using the show interface stats Command Use the show interface stats command for infor mation about the interface.
7-49 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Enabling the Second Proc.
7-50 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Enabling the Second Pr.
7-51 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Enabling the Second Processor o n the NPE-G1 Gi0/1.201 201 up RX punts 29 Gi0/1.
7-52 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Copying the Saved Configuration to NVRAM Compiled Wed 02-Feb-05 04:57 by ROM: System Bootstrap, Version 12.
7-53 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Copying the Saved Con fi.
7-54 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Copying the Saved Conf.
7-55 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Copying the Saved Con figuration to NVRAM Step 4 The system prompts you to select a host or networ k configu ration fi le.
7-56 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Auxiliary and Console .
7-57 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Configuring the Native G.
7-58 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Configuring the Native Gigabit Ethe rnet Interfaces ip address 10.198.75.
7-59 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Using show Commands to C.
7-60 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Using show Com mands to Check the Installation T o determine the hard ware conf iguration of your NPE-G1 or NP E-G2, use the sho w version command.
7-61 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Using show Commands to C.
7-62 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Upgrading the Cisco IO.
7-63 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Upgrading ROMmon on the .
7-64 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Upgrading ROMmon on th.
7-65 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Troubleshooting the Upgr ade Running new upgrade for first time System Bootstrap, Version 12.
7-66 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Troubleshooting the U .
7-67 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Upgrading FPGA on the NPE-G2 Upgrading FPGA on the NPE-G2 A field-programmable gat e array (FPGA) device exists on the NPE-G2.
7-68 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Fiber Optic Cleaning I.
CH A P T E R 8-1 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 8 Preparation for Installation This chapter pro vides a list of parts and tools you n.
8-2 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 8 Preparatio n for Installation Software and Hardwar e Requirements If your router is mo.
8-3 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 8 Pre paration for Installation Software and Hardware Requirements Use the follo wing table to deter mine supported NPEs or the NSE-1 for specif ic routers.
8-4 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 8 Preparatio n for Installation Software and Hardwar e Requirements Port Adapter Jacket Card Support The Port Adapter Jacket Card inse rts into the I/O con troller slot of a Cisco 7200 VXR router when an NPE-G2 or NP E-G1 is installe d.
8-5 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 8 Pre paration for Installation Software and Hardware Requirements • Cisco uBR7 246VXR Cisco IOS Re lease 12.1(6)EC or later releases of 12.
8-6 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 8 Preparatio n for Installation Software and Hardwar e Requirements • Cisco 72 04 and Cisco 72 06 Cisco IOS Release 11.1(8) Cisco IOS Rel ease 11.
8-7 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 8 Pre paration for Installation Software and Hardware Requirements Cisco uBR7200 series • Cisco uBR7246VXR — — — Cisco IOS Release 12.
8-8 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 8 Preparatio n for Installation Software and Hardwar e Requirements Safety Guidelines Follo wing are saf ety guidelines that you should fol low wh en working with an y equipment that connects to electrical po wer or telephone wiri ng.
8-9 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 8 Pre paration for Installation Software and Hardware Requirements Safety Warnings War ni ng IMPORT ANT SAFETY INSTRUCTIONS This warning symbol means danger .
8-10 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 8 Preparatio n for Installation Software and Hardwar e Requirements War nun g WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol b edeutet Gefahr .
8-11 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 8 Pre paration for Installation Software and Hardware Requirements Va r n i n g ! VIKTIGA SÄKERHETSANVISNINGAR Denna varningssignal signalerar fara.
8-12 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 8 Preparatio n for Installation Software and Hardwar e Requirements Avi so INSTRUÇÕES IMPORT A NTES DE SEGURANÇA Este símbolo de aviso significa perigo.
8-13 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 8 Pre paration for Installation Software and Hardware Requirements.
8-14 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 8 Preparatio n for Installation Software and Hardwar e Requirements Electrical Equipmen.
8-15 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 8 Pre paration for Installation Software and Hardware Requirements • Nev er touch unin sulated telep hone wires or te rminals unless the telephone l ine has been disconnected at the network interface.
8-16 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 8 Preparatio n for Installation Software and Hardwar e Requirements Figur e 8-3 Hand li.
CH A P T E R 9-1 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 9 Removing and Installing the NPE or NSE This chapter describes ho w to remo ve a net.
9-2 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Caution .
9-3 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Powering D.
9-4 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Disconne.
9-5 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Figur e 9-.
9-6 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Step 3 Remove the cable tie that secures the –V , +V , and gr ound leads to the pow er supply faceplate.
9-7 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Disconnecting DC-Input Power fr om a Cisco uBR7246 Router T o disconnect DC-i nput po wer from a Cisco uBR7346 rou ter , complete the fol lowin g steps.
9-8 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Step 4 Using a 3/16-inch flat-blade screwdri v er , loosen the screw belo w the +V lead rec eptacle and pull the lead from the connector .
9-9 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Note Repeat the Steps 1 to 5 to disconnect secondary po wer supply , if connected.
9-10 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Figur e.
9-11 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Removing .
9-12 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Figur e.
9-13 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Installin.
9-14 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Caution When inserting SIMMs, use f irm but not e xcessiv e pressure.
9-15 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Figur e 9-9 Opening DIMM Soc k et Latc hes Note The SDRAM DIMM sockets on th e NPE-175, NPE-225, and NP E-300 are paral lel to the circuit board.
9-16 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Figur e 9-1 1 Handling the DIMM Caution T o pre vent ESD damage, handle the DIMM b y the card edges only .
9-17 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE W ith the.
9-18 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Removin.
9-19 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Figur e 9.
9-20 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Caution SODIMMs are sensitiv e components that are susc eptible to ESD damage.
9-21 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE SIMMs or DIMMs should b e aligned at the same angle an d the same height as others on the board when properly installed.
9-22 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Caution.
9-23 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Figur e 9.
9-24 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE War ni ng Read the installation instruc tions before you connect the sy stem to its power source.
9-25 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Reconnect.
9-26 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Reconne.
9-27 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Reconnect.
9-28 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Figur e.
9-29 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Reconnect.
9-30 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Figur e 9-22 Connecting DC-Input P ower t o a Cisco uBR7246VXR Router Step 3 If necessary , use a wire stri pper to strip approximately 0 .
9-31 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Step 4 Connect the two -hole grounding lu g on the groundin g lead to the M5 gro unding receptacles with the M5 nuts.
9-32 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Figur e 9-24 Replacing the Str ain-Relief Cov er on a Cisco uBR7246VXR Rout er DC-Input P ower Supply Step 9 Restore current to the –V and +V leads.
9-33 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Powering .
9-34 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Step 5 Observe the initi alization process.
CH A P T E R 10-1 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 10 Configuration Tasks and Troubleshooting Information This chapter pr ovides conf igurat ion and troubleshooti ng information.
10-2 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 10 Config uration Tasks and Troubleshooting Information Boot Changes in Cisco IOS Release 12.2 Note Before enabling the PXF processor , you must ha ve IP routi ng and IP CEF switching turned o n.
10-3 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 10 Configuration Tasks and Troublesh ooting Information Troubleshooting the NPE-G1 o r NP.
10-4 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 10 Config uration Tasks and Troubleshooting Information .Troubleshooting the NPE-100 Through NPE-400 • Check the Cisco IOS release running on the router .
10-5 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 10 Configuration Tasks and Troublesh ooting Information NPE or NSE show Commands Image text-base:0x60008900, data-base:0x6141C000 (display text omitted) cisco 7206VXR (NSE-1) processor (revision B) with 57344K/8192K bytes of memory.
10-6 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 10 Config uration Tasks and Troubleshooting Information NSE-1 show Commands 0x20:37 35 .
10-7 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 10 Configuration Tasks and Troublesh ooting Information NSE-1 show Commands PXF Statistic.
10-8 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 10 Config uration Tasks and Troubleshooting Information NSE-1 show Commands ICM0(b4~13).
10-9 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 10 Configuration Tasks and Troublesh ooting Information NSE-1 show Commands Using the sho.
10-10 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 10 Config uration Tasks and Troubleshooting Information NSE-1 Error Messages • show .
10-11 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 10 Configuration Tasks and Troublesh ooting Information Using Debugging Comman ds and PX.
10-12 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 10 Config uration Tasks and Troubleshooting Information PXF Troubleshootin g Information The PXF has 16 processors, only one of which is in us e at a time when there is a lo w traf fic rate.
10-13 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 10 Configuration Tasks and Troublesh ooting Information PXF Troubleshooting Information Note CPU usage be comes more ef ficient as packet load increases.
10-14 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 10 Config uration Tasks and Troubleshooting Information Removing and Replacing an AC-I.
10-15 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 10 Configuration Tasks and Troublesh ooting Information Removing and Replacing an AC-In .
10-16 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 10 Config uration Tasks and Troubleshooting Information Removing and Replacing an AC-I.
10-17 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 10 Configuration Tasks and Troublesh ooting Information Fiber Optic Cleaning Information.
10-18 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 10 Config uration Tasks and Troubleshooting Information Fiber Optic Cleaning Informati.
IN-1 Network Processing Engin e and Network Services Engine Installation and Configuration OL-4448-12 INDEX B Bable Manage ment Brack et 4-post Rack 7-34 C Cable Manage ment Brack et How to Install 7-.
Index IN-2 Network Processing Engine and Network Servi ces Engine Installation and Configura tion OL-4448-12 I Installing and Removi g a CompactFlash Disk 6-7 Installing DIMMs NPE-175, NPE-225, NPE-30.
Index IN-3 Network Processing Engin e and Network Services Engine Installation and Configuration OL-4448-12 Replacing SODIMMs 7-26 Resetting the Interface 7-58 ROMmon upgrade Error Messages 7-66 Runni.
Index IN-4 Network Processing Engine and Network Servi ces Engine Installation and Configura tion OL-4448-12 RJ-45 Port Pinout 6-14 RJ-45 Port Pinouts 5-11 ROMmon, NPE-G1 or NPE-G2 Changing Preference.
Ein wichtiger Punkt beim Kauf des Geräts Cisco Systems NPE-225 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Cisco Systems NPE-225 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Cisco Systems NPE-225 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Cisco Systems NPE-225 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Cisco Systems NPE-225 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Cisco Systems NPE-225 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Cisco Systems NPE-225 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Cisco Systems NPE-225. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Cisco Systems NPE-225 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.