Benutzeranleitung / Produktwartung ACIP-SM(=) des Produzenten Cisco Systems
Zur Seite of 32
1 Customer Order Number: Cisco Systems, Inc. All rights reser ved. 170 West Tasman Drive San Jose, CA 95134-1706 USA Cisco Systems, Inc. Corporate Headquarters Copyright © 1997 Documentation P ar t N.
2 A TM Cable Interf ace Processor (A CIP) Installation and Configuration A TM T erms and Acron yms A TM T erms and Acr on yms The follo wing are common A TM terms and acronyms for your reference: AAL—A TM Adaptation Layer . An AAL defines the conv ersion of user information into cells.
ATM Cable Interface Processor (ACIP) Installation and Configuration 3 Asynchronous Transfer Mode Overview SONET—Synchronous Optical Network. An A TM UNI specification and American National Standards Institute (ANSI) standard (T1.105-1988) for optical digital transmission at hierarchical rates from 51.
4 A TM Cable Interf ace Processor (A CIP) Installation and Configuration A CIP Description An A TM connection transfers raw bits of information to a destination router/host.
ATM Cable Interface Processor (ACIP) Installation and Configuration 5 ACIP Description A CIP Interf ace The A CIP’ s A TM interface is full duplex. Y ou must use the appropriate A TM interface cable to connect the A CIP with external A TM equipment.
6 A TM Cable Interf ace Processor (A CIP) Installation and Configuration A CIP Description T able 2 T ypical Fiber-Optic Link Atten uation and Dispersion Limits Appro ximating the A CIP P ower Margin.
ATM Cable Interface Processor (ACIP) Installation and Configuration 7 ACIP Description For the A CIP , the signal must meet the worst case parameters listed in T able 4.
8 A TM Cable Interf ace Processor (A CIP) Installation and Configuration A CIP Description Figure 2 Duplex SC-T ype Connector Figure 3 Simplex SC-T ype Connector The multimode cable connects to the SC connector on the PLIM.
ATM Cable Interface Processor (ACIP) Installation and Configuration 9 ACIP Installation Prerequisites A CIP Installation Prerequisites Before you begin the A CIP installation, revie w the guidelines in this section to ensure a successful installation, to av oid injuring yourself, or to a void damaging the equipment.
10 A TM Cable Interf ace Processor (A CIP) Installation and Configuration A CIP Installation Prerequisites Figure 7 shows the rear of the 7-slot Cisco 7507 router . In the Cisco 7507, up to two slots (2 and 3) are reserved for the Route Switch Processor (RSP2), which contains the system processor and performs packet switching functions.
ATM Cable Interface Processor (ACIP) Installation and Configuration 11 ACIP Installation Prerequisites Figure 8 shows the rear of the 13-slot Cisco 7513. In the Cisco 7513, up to two slots (6 and 7) are reserved for the Route Switch Processor (RSP2), which contains the system processor and performs packet switching functions.
12 A TM Cable Interf ace Processor (A CIP) Installation and Configuration A CIP Installation Prerequisites List of P ar ts and T ools Y ou need the following tools and parts to install or upgrade an A CIP . If you need additional equipment, contact your service representativ e for ordering information.
ATM Cable Interface Processor (ACIP) Installation and Configuration 13 ACIP Installation Prerequisites Attention Ce symbole d'av ertissement indique un danger . V ous vous trouv ez dans une situation pouvant causer des blessures ou des dommages corporels.
14 A TM Cable Interf ace Processor (A CIP) Installation and Configuration A CIP Installation Prerequisites Electrical Equipment Follo w these basic guidelines when working with an y electrical equipm.
ATM Cable Interface Processor (ACIP) Installation and Configuration 15 ACIP Installation Prerequisites • When removing an A CIP , use the ejectors to release the bus connectors from the backplane. Hold the handle on the front of an A CIP with one hand and support the bottom edge of the metal carrier with the other hand.
16 A TM Cable Interf ace Processor (A CIP) Installation and Configuration Installing and Removing an A CIP Installing and Remo ving an A CIP An A CIP slides into slots in the rear of a Cisco 7500 series chassis and connects directly to the backplane.
ATM Cable Interface Processor (ACIP) Installation and Configuration 17 Attaching Network Interface Cables to the ACIP Attaching Netw ork Interface Cables to the A CIP The A CIP interfaces are full duple x.
18 A TM Cable Interf ace Processor (A CIP) Installation and Configuration Using LEDs to Check A CIP Status After you install the A CIP and attach the interface cable between the A CIP’ s interface port and your cable headend (T eraLink 1000) or external A TM switch, verify the installation by observing the LED states and the console display .
ATM Cable Interface Processor (ACIP) Installation and Configuration 19 Using show Commands to Verify Interface Status Step 6 If this installation was a replacement A CIP , use the show interfaces or show controllers cbus command to v erify the status of the A TM interface.
20 A TM Cable Interf ace Processor (A CIP) Installation and Configuration Using show Commands to V erify Interface Status Follo wing is an example of the show contr oller cb us display . Note the display of the A CIP’ s microcode version (20.2), PLIM type (SONET), and a v ailable bandwidth (155 Mbps).
ATM Cable Interface Processor (ACIP) Installation and Configuration 21 Configuring the ACIP Configuring the A CIP Configuring the A CIP is a two step process: first you configure the A CIP , then you configure the cable headend and/or A TM switch.
22 A TM Cable Interf ace Processor (A CIP) Installation and Configuration Configuring the A CIP Configure an A CIP Interf ace The A CIP interface (or subinterf ace) uses the configuration defaults sho wn in T able 1.
ATM Cable Interface Processor (ACIP) Installation and Configuration 23 Configuring the ACIP Configure Cable P arameters T o assign the A TM interface on the A CIP to a cable headend and specify the c.
24 A TM Cable Interf ace Processor (A CIP) Installation and Configuration Configuring the A CIP T o create a bridge-group virtual interface, perform the follo wing tasks in interface configuration .
ATM Cable Interface Processor (ACIP) Installation and Configuration 25 Configuring the ACIP Monitor and Maintain the A CIP After configuring the new interf ace, you can display its status. Y ou can also display the current status of connections and activ e modems on each interface.
26 A TM Cable Interf ace Processor (A CIP) Installation and Configuration A CIP Error Statistics A CIP Error Statistics The A CIP maintains a count of certain errors. In addition to keeping a count of these errors, the A CIP also takes a snapshot of the last VCI/VPI that caused the error .
ATM Cable Interface Processor (ACIP) Installation and Configuration 27 Using the Debug ATM Commands • Use the show atm vc n command to display statistics for a gi ven PVC, where n is the VCD. The follo wing is sample output from the show atm vc n command, with VCD 1 specified: Router# show atm vc 1 ATM3/0.
28 A TM Cable Interf ace Processor (A CIP) Installation and Configuration Examples of A TM Err or Messages • T o display A TM events, use the debug atm e vents command: This command displays ev ent changes to the A CIP . Reset, VC configurations, ACIP configurations, and PLIM failures are displayed.
ATM Cable Interface Processor (ACIP) Installation and Configuration 29 Examples of ATM Error Messages Error Messa ge AIP_lov e_note(A TM2/0): asr=0xaaaa Explanation Receiv ed a love note from the A CIP . Love notes are messages that the A CIP passes to the RSP to indicate an action or ev ent has taken place.
30 A TM Cable Interf ace Processor (A CIP) Installation and Configuration Examples of A TM Err or Messages Follo wing is a list of possible error messages displayed when you enter the debug atm err ors command: Error Messa ge AIP_lov e_note(A TM2/0): UNKNO WN asr=0x0000 Explanation A bad lov e note message was passed back by the A CIP .
ATM Cable Interface Processor (ACIP) Installation and Configuration 31 Examples of ATM Error Messages Error Messa ge atm_pakalign(A TM2/0): In v alid VC(65535) receiv ed, type=0xaaaa Explanation A packet was recei ved by the A CIP with a VC that is out of the valid range of VCs.
32 A TM Cable Interf ace Processor (A CIP) Installation and Configuration Cisco Connection Online Cisco Connection Online Cisco Connection Online (CCO) is Cisco Systems’ primary , real-time support channel. Maintenance customers and partners can self-register on CCO to obtain additional content and services.
Ein wichtiger Punkt beim Kauf des Geräts Cisco Systems ACIP-SM(=) (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Cisco Systems ACIP-SM(=) noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Cisco Systems ACIP-SM(=) - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Cisco Systems ACIP-SM(=) reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Cisco Systems ACIP-SM(=) erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Cisco Systems ACIP-SM(=) besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Cisco Systems ACIP-SM(=) verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Cisco Systems ACIP-SM(=). Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Cisco Systems ACIP-SM(=) gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
