Benutzeranleitung / Produktwartung MP3200 des Produzenten Cino
Zur Seite of 196
1 MP3200 Series Programming Reference Pr eliminary Release Rev . 02.
Progr amming Reference VERSAJET MP3200 Propriet ary S t atement The information contained herein is propriet ary and is provided sorely for the purpose of allowing customer s to operate and maintain the equipment described herein. PC W orth Int’l Co.
Progr amming Reference VERSAJET MP3200 T able of Contents Chapter 1 Introduction ................................................................................................... 1 JCL Command Set s ..................................................
Progr amming Reference VERSAJET MP3200 ESC ? ......................................................................................................................... ...................... 40 ESC R.....................................................
Progr amming Reference VERSAJET MP3200 ESC * .......................................................................................................................... ...................... 74 GS * ....................................................
Progr amming Reference VERSAJET MP3200 GS h .......................................................................................................................... ..................... 160 GS w .....................................................
Progr amming Reference VERSAJET MP3200 Introduction Thank you for choosing VERSAJET MP3200 Series Mobile Printer . The MP3200 series mobile printer is designed with rugged yet lightweight architecture, delivering the ultimate convenience of mobility to meet your on-demand labels and receipts printing requirement s.
Introduction Progr amming Reference VERSAJET MP3200 JCL Command Sets ESC/POS (Epson S tandard Code for Point of Sales) is one of the most world-popular command sets, which was designed to provide the expandability and universal applicability demanded by the market.
Introduction Progr amming Reference VERSAJET MP3200 Commands Comparison between JCL and ESC/POS Command Descriptions JCL ESC/POS HT Horizontal tab v v LF Print and line feed v v FF Print and return to.
Introduction Progr amming Reference VERSAJET MP3200 Command Descriptions JCL ESC/POS SC ? Cancel user-defined characters v v ESC @ Initialize printer v v ESC D Set horizontal tab positions v v ESC E T.
Introduction Progr amming Reference VERSAJET MP3200 Command Descriptions JCL ESC/POS ESC d Print and feed n lines v v ESC p Generate pulse v ESC t Select character code table v v ESC { Turn upside-dow.
Introduction Progr amming Reference VERSAJET MP3200 Command Descriptions JCL ESC/POS GS Set relative vertical print position in page mode v v GS ^ Execute macro v v GS a Enable/disable Automatic Stat.
Introduction Progr amming Reference VERSAJET MP3200 Command Descriptions JCL ESC/POS GS c Print counter setup v GS ( K Printing density setup v GS ( k Specify and print the symbol v RS m n Media lengt.
Introduction Progr amming Reference VERSAJET MP3200 Command Descriptions JCL ESC/POS ESC ESC 13 Radio off time setup v ESC ESC 14 Setting IrDA protocol v ESC ESC D Restore default value v 8 Preliminary Rev .
Progr amming Reference VERSAJET MP3200 Command Overview This chapter covers following topics to present the supported commands that are used with MP3200(BT) series : Command Notation Explanations of T erms Supported Commands 9 Preliminary Rev .
Command Overview Progr amming Reference VERSAJET MP3200 Command Notation [Name] The name of the command. [Format] The code sequence. [Range] Gives the allowable ranges for the arguments. [Default] Gives the default values, if any, for the command parameters.
Command Overview Progr amming Reference VERSAJET MP3200 Explanation of T erms (1) Receive buffer The receive buffer is a buffer that stores, as is, the data received from the host (the reception data). The reception data is stored in the receive buffer temporarily, and is then processed sequentially.
Command Overview Progr amming Reference VERSAJET MP3200 (5) Printable area The maximum range within which printing is possible under the printer specifications. The printable area for this printer is as follows: The length of the horizontal direction in standard mode: approximately 48 mm {1.
Command Overview Progr amming Reference VERSAJET MP3200 (10) LSB Least Significant Bit (11) Base line Standard position when character data is stored in the print buffer. Normal character in standard mode and page mode: A y * Base line * When font A (12×24 dots) is selected, this height is for 24 dots.
Command Overview Progr amming Reference VERSAJET MP3200 Supported Commands In these tables, click any name to see the command description. Please refer following instructions before you utilize these commands to confiure your MP3200(BT) : St andard mode | : Enabled.
Command Overview Progr amming Reference VERSAJET MP3200 Commands Listed by F unction Function Ty p e Command Description Classification St andard Mode Page Mode Print LF Print and line feed Executing .
Command Overview Progr amming Reference VERSAJET MP3200 Function Ty p e Command Description Classification St andard Mode Page Mode Character ESC G T urn double-strike mode on/off Setting || Character.
Command Overview Progr amming Reference VERSAJET MP3200 Function Ty p e Command Description Classification St andard Mode Page Mode Bit Image ESC * Select bit-image mode Executing || Bit Image GS * De.
Command Overview Progr amming Reference VERSAJET MP3200 Function Ty p e Command Description Classification St andard Mode Page Mode Miscellaneous RS W Clear printing area Setting Ignored | Miscellaneo.
Command Overview Progr amming Reference VERSAJET MP3200 Function Ty p e Command Description Classification St andard Mode Page Mode Flash ESC ESC 00 Communication parameter setup (RS232C) Executing ||.
Command Overview Progr amming Reference VERSAJET MP3200 Commands Listed in Alphanumeric Order Command Function Ty p e Description Classification St andard Mode Page Mode CAN Character Cancel print dat.
Command Overview Progr amming Reference VERSAJET MP3200 Command Function Ty p e Description Classification St andard Mode Page Mode ESC ESC 13 Flash Radio off time setup Executing || ESC ESC 14 Flash .
Command Overview Progr amming Reference VERSAJET MP3200 Command Function Ty p e Description Classification St andard Mode Page Mode ESC & Character Define user-defined characters Setting || ESC ? .
Command Overview Progr amming Reference VERSAJET MP3200 Command Function Ty p e Description Classification St andard Mode Page Mode GS h Bar Code Set bar code height Setting || GS I Miscellaneous T ra.
Command Overview Progr amming Reference VERSAJET MP3200 Command Function Ty p e Description Classification St andard Mode Page Mode HT Print Position Horizontal tab Executing || LF Print Print and lin.
Progr amming Reference VERSAJET MP3200 Command Descriptions This section contains the command codes for the MP3200(BT) which allows you to configure your printer for particular application to match your specific requirements. Each command begins on a sep arate page with it s own heading to help you find the key information about each command.
Command Descriptions Progr amming Reference VERSAJET MP3200 LF [Name] Print and Line Feed [Format] ASCII LF Hex 0A Decimal 10 [Range] None [Default] None [Description] Prints the dat a in the print buf fer and feed one line [Notes] The amount of paper fed per line is based on the value set using the line sp acing command (ESC 2 or ESC 3).
Command Descriptions Progr amming Reference VERSAJET MP3200 CR [Name] Printing and carriage return [Format] ASCII CR Hex 0D Decimal 13 [Range] None [Default] None [Description] Executes printing and one line feed as LF . [Notes] After printing, the printing position moves to the beginning of the line.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC J [Name] Print and feed paper [Format] ASCII ESC J n Hex 1B 4A n Decimal 27 74 n [Range] 0 Љ n Љ 255 [Default] None [Description] Prints the dat a in the print buf fer and feeds the paper n x (vertical or horizont al motion unit).
Command Descriptions Progr amming Reference VERSAJET MP3200 When this command is processed in page mode, only the printing position moves, and the printer does not perform actual printing. This command is used to temporarily feed a specific length without changing the line spacing set by other commands.
Command Descriptions Progr amming Reference VERSAJET MP3200 FF [Name] Print and return to standard mode [Format] ASCII FF Hex 0C Decimal 12 [Range] None [Default] None [Description] In page mode, print s the data in the printer buf fer collectively and returns to standard mode.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC d [Name] Print and feed n lines [Format] ASCII ESC d n Hex 1B 64 n Decimal 27 100 n [Range] 0 Љ n Љ 255 [Default] None [Description] Prints the dat a in the print buf fer and feeds n lines.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC FF [Name] Print data in page mode [Format] ASCII ESC FF Hex 1B 0C Decimal 27 12 [Range] None [Default] None [Description] In page mode, print s all buffered data in the print able area collectively .
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC 2 [Name] Select default line spacing [Format] ASCII ESC 2 Hex 1B 32 Decimal 27 50 [Range] None [Default] None [Description] Sets the line sp acing to the “default line spacing”. [Notes] The line sp acing can be independently in standard and page mode.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC 3 [Name] Set line spacing [Format] ASCII ESC 3 n Hex 1B 33 n Decimal 27 51 n [Range] 0 Љ n Љ 255 [Default] Amount of line spacing which corresponds to “default line sp acing” (See ESC 2 for the line spacing).
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC SP [Name] Set right-side character spacing [Format] ASCII ESC SP n Hex 1B 20 n Decimal 27 32 n [Range] 0 Љ n Љ 255 [Default] n = 0 [Description] Sets the right-side character sp acing to n x (horizontal or vertical motion unit).
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC % [Name] Select/cancel user-defined character set [Format] ASCII ESC % n Hex 1B 25 n Decimal 27 37 n [Range] 0 Љ n Љ 255 [Default] n = 0 [Description] Selects or cancels user-defined character set.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC & [Name] Define user-defined characters [Format] ASCII ESC & y c1 c2 [x1 d1 d(y x x1)] [xk d1 d(y x xk)] Hex 1B 26 y c1 c2 [x1 d.
Command Descriptions Progr amming Reference VERSAJET MP3200 Data( d ) specifies a bit printed to 1 and not printed to 0. The dot pattern is in the horizont al direction from the left side. Any remaining dots on the right side are blank. The data to define a user defined character is ( y x x ) bytes.
Command Descriptions Progr amming Reference VERSAJET MP3200 Only the MSB can be printed in the third byte for vertical direction of font B. A user-defined character and downloaded bit image cannot be defined simultaneously . 39 Preliminary Rev .
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC ? [Name] Cancel user-defined characters [Format] ASCII ESC ? n Hex 1B 3F n Decimal 27 63 n [Range] 32 Љ n Љ 126 [Default] None [Description] Cancels the user-defined characters defined for the character code n .
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC R [Name] Select an international character set [Format] ASCII ESC R n Hex 1B 52 n Decimal 27 82 n [Range] 0 ≦ n ≦ 10 [Default] n = 0.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC t [Name] Select character code table [Format] ASCII ESC t n Hex 1B 74 n Decimal 27 1 16 n [Range] 0 n 8, 16 n 19, n = 25.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC ! [Name] Select print mode(s) [Format] ASCII ESC ! n Hex 1B 21 n Decimal 27 33 n [Range] 0 Љ n Љ 255 [Default] n = 0 [Description] Selects print mode(s) using n as follows: Bit Off/On Hex Decimal Function Off 00 0 Character font A (12 × 24).
Command Descriptions Progr amming Reference VERSAJET MP3200 [Notes] When both double-height and double-width modes are selected, quadruple size characters are printed. The printer can underline all characters, but can not underline the space set by HT or 90° clockwise rotated characters.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC - [Name] Turn underline mode on/of f [Format] ASCII ESC - n Hex 1B 2D n Decimal 27 45 n [Range] 0 n 2, 48 n 50 [Default].
Command Descriptions Progr amming Reference VERSAJET MP3200 Underline mode can also be turned on or off by using ESC ! . Note, however , that the last received command is effective. This command does not affect Kanji printing. 46 Preliminary Rev .
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC E [Name] Turn emphasized mode on/f f [Format] ASCII ESC E n Hex 1B 45 n Decimal 27 69 n [Range] 0 Љ n Љ 255 [Default] n = 0 [Description] T urns emphasized mode on/ff When the LSB of n is 0, emphasized mode is turned off.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC G [Name] Turn double-strike mode on/f f [Format] ASCII ESC G n Hex 1B 47 n Decimal 27 71 n [Range] 0 Љ n Љ 255 [Default] n = 0 [Description] T urns double-strike mode on/ff [Notes] When the LSB of n is 0, double-strike mode is turned off.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC { [Name] Turn up side-down printing mode on/ff [Format] ASCII ESC { n Hex 1B 7B n Decimal 27 123 n [Range] 0 Љ n Љ 255 [Default] n = 0 [Description] In standard mode, turns up side-down printing mode on/ff When the LSB of n is 0, emphasized mode is turned off.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC V [Name] Turn 90° clockwise rot ation mode on/off [Format] ASCII ESC V n Hex 1B 56 n Decimal 27 86 n [Range] n = 0, 1, 48, 49 [Default].
Command Descriptions Progr amming Reference VERSAJET MP3200 The 90° clockwise rotation mode has no ef fect in page mode. If this command is processed in page mode, an internal flag is activated, and this flag is enabled when the printer returns to standard mode.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ! [Name] Select character size [Format] ASCII GS ! n Hex 1D 21 n Decimal 29 33 n [Range] 0 Љ n Љ 7, 16 Љ n Љ 23, 32 Љ n Љ 39, 48 Љ.
Command Descriptions Progr amming Reference VERSAJET MP3200 Character height selection Bit 2 Bit 1 Bit 0 Hex Decimal Height Off Of f Off 00 0 1(normal) Off Off On 01 1 2(double-height) O f fO nO f f 0.
Command Descriptions Progr amming Reference VERSAJET MP3200 In page mode, double-height and double-wid th are on the character orientation. The setting of the character size of alphanumeric and Katakana is ef fective until ESC ! or ESC @ is executed, the printer is reset, or the power is turned off.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS B [Name] Turn white/black reverse printing mode on/f f [Format] ASCII GS B n Hex 1D 42 n Decimal 29 66 n [Range] 0 Љ n Љ 255 [Default] n = 0 [Description] T urns white/black reverse printing mode on/ff When the LSB of n is 0, white/black reverse printing mode is turned off.
Command Descriptions Progr amming Reference VERSAJET MP3200 CAN [Name] Cancel printing data in page mode [Format] ASCII CAN Hex 18 Decimal 24 [Range] None [Default] None [Description] In p age mode, deletes all the print data for the current printing area.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC M [Name] Select character font [Format] ASCII ESC M n Hex 1B 4D n Decimal 27 77 n [Range] 0, 1, 48, 49 [Default] n = 0 [Description] Sel.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC $ [Name] Set absolute print position [Format] ASCII ESC $ nL nH Hex 1B 24 nL nH Decimal 27 36 nL nH [Range] 0 Љ nL 255, 0 ЉЉ nH 255 .
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC [Name] Set relative print position [Format] ASCII ESC nL nH Hex 1B 5C nL nH Decimal 27 92 nL nH [Range] 0 Љ nL 255, 0 ЉЉ nH 255 Љ [Description] Moves the print starting position to ( nL + nH x256) x (horizont al or vertical motion unit) from the current position.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC a [Name] Select justification [Format] ASCII ESC a n Hex 1B 61 n Decimal 27 45 n [Range] 0 n 2, 48 n 50 [Default] n = 0 .
Command Descriptions Progr amming Reference VERSAJET MP3200 HT [Name] Horizontal tab [Format] ASCII HT Hex 09 Decimal 9 [Range] None [Default] None [Description] Moves the printing position to the next horizontal t ab. [Notes] This command is ignored unless the next horizontal t ab position has been set.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC D [Name] Set horizontal tab positions [Format] ASCII ESC D n …nk NUL Hex 1B 44 n1…nk 0 Decimal 27 68 n1…nk 0 [Range] 1 Љ n Љ 255.
Command Descriptions Progr amming Reference VERSAJET MP3200 When [ n ] is less than or equal to the preceding value [ n ] k -1, horizontal t ab setting is finished, and the following data is processed as normal dat a. k is not transmission data to the printer .
Command Descriptions Progr amming Reference VERSAJET MP3200 GS L [Name] Set left margin [Format] ASCII GS L nL nH Hex 1D 4C nL nH Decimal 29 76 nL nH [Range] 0 Љ ( nL + nH x 256) Љ 65535 (0 Љ nL Љ.
Command Descriptions Progr amming Reference VERSAJET MP3200 Left margin setting is ef fective until ESC @ is executed, the printer is reset, or the power is turned off. Left margin position is lef t edge of the printable area. If lef t margin setting is changed, left edge of the printable area will move.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS W [Name] Set printable area width [Format] ASCII GS W nL nH Hex 1D 57 nL nH Decimal 29 87 nL nH [Range] 0 Љ ( nL + nH x 256) Љ 65535 (0.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC W [Name] Set printable area in page mode [Format] ASCII ESC W xL xH yL yH dxL dxH dyL dyH Hex 1B 57 xL xH yL yH dxL dxH dyL dyH Decimal .
Command Descriptions Progr amming Reference VERSAJET MP3200 If [horizontal logical origin + printing area wid th] exceeds the printable area, the printing area width is automatically set to [horizont al print able area – horizontal logical origin].
Command Descriptions Progr amming Reference VERSAJET MP3200 paper ………………………….xLxH , yL yH page mode range ………………………… dxLdxH dyLdyH 69 Preliminary Rev .
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC T [Name] Select print direction in page mode [Format] ASCII ESC T n Hex 1B 54 n Decimal 27 84 n [Range] 0 n 3, 48 n 51 [.
Command Descriptions Progr amming Reference VERSAJET MP3200 This command setting has no effect in st andard mode. If this command is processed in standard mode, an internal flag is activated, and this flag is enabled when the printer selects p age mode.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS $ [Name] Set absolute vertical print position in page mode [Format] ASCII GS $ nL nH Hex 1D 24 nL nH Decimal 29 36 nL nH [Range] 0 Љ nL .
Command Descriptions Progr amming Reference VERSAJET MP3200 GS [Name] Set relative vertical print position in page mode [Format] ASCII GS nL nH Hex 1D 5C nL nH Decimal 29 92 nL nH [Range] 0 Љ nL 25.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC * [Name] Select bit-image mode [Format] ASCII ESC * m nL nH d1dk Hex 1B 2A m nL nH d1 dk Decimal 27 92 m nL nH d1 dk [Range] m = 0, 1, 3.
Command Descriptions Progr amming Reference VERSAJET MP3200 The bit-image is not affected by print mode(emphasized, double-strike, underline, character size, white/black reverse printing, or 90° clockwise-rotated), except for upside-down printing mode.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS * [Name] Define downloaded bit image [Format] ASCII GS * x y d1 d(x x y x 8) Hex 1D 2A x y d1 d(x x y x 8) Decimal 29 42 x y d1 d(x x y x 8) [Range] 1 Љ x Љ 255 1 Љ y 48 Љ 0 Љ d 255 Љ k = x x y x 8 [Default] None [Description] Defines a downloaded bit image.
Command Descriptions Progr amming Reference VERSAJET MP3200 A downloaded bit image and a user-defined character cannot be defined simultaneously . When this command is executed, the user-defined character is cleared. The downloaded bit image is printed by GS / .
Command Descriptions Progr amming Reference VERSAJET MP3200 GS / [Name] Print downloaded bit image [Format] ASCII GS / n Hex 1D 2F n Decimal 29 47 n [Range] 0 n 3, 48 n 51 [Default] n = 0 [Description] Prints a downloaded bit image using the mode specified by n .
Command Descriptions Progr amming Reference VERSAJET MP3200 If the downloaded bit image to be printed exceeds the printable area, the excess dat a is not printed.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS v 0 [Name] Print raster bit image [Format] ASCII GS v 0 n xL xH yL yH d1 dk Hex 1D 76 30 n xL xH yL yH d1 dk Decimal 29 1 18 48 n xL xH y.
Command Descriptions Progr amming Reference VERSAJET MP3200 [Notes] In standard mode, this command is ef fective only when there is no data in the print buf fer . This command has no effect in the print modes (emphasized, double-strike, underline, character size, or white/black reverse printing) for raster bit image.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS : [Name] S tart/end macro definition [Format] ASCII GS : Hex 1D 3A Decimal 29 58 [Range] None [Default] None [Description] S tarts or end.
Command Descriptions Progr amming Reference VERSAJET MP3200 The following commands cannot be contained in a macro. Do not use these commands while the macro is being defined: FS q , GS ( A , GS ^ , and GS v 0 .
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ^ [Name] Execute macro [Format] ASCII GS ^ r t m Hex 1D 5E r t m Decimal 29 94 r t m [Range] 1 Љ r Љ 255 0 Љ t Љ 255 m = 0, 1 [Defaul.
Command Descriptions Progr amming Reference VERSAJET MP3200 The macro is defined by GS : . Macro function is useful to print the same data repeatedly . T o define a macro definition, send GS : just before and after the dat a desired to be repeated.
Command Descriptions Progr amming Reference VERSAJET MP3200 FS & [Name] Select Kanji character mode [Format] ASCII FS & Hex 1C 26 Decimal 28 38 [Description] Selects Kanji character mode. [Notes] Kanji codes are processed in order of the first byte and the second byte.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS P [Name] Set horizontal and vertical motion units [Format] ASCII GS P x y Hex 1D 50 x y Decimal 29 80 x y [Range] 0 x 255, 0 y 255 [Default] x = 203, y = 203 [Description] Sets the horizont al and vertical motion units to 1/ x and 1/ y inch, respectively .
Command Descriptions Progr amming Reference VERSAJET MP3200 The setting of this command is effective until ESC @ is executed, the printer is reset, or the power is turned off. The calculated result from combining this command with others is truncated to the minimum value of the mechanical pitch.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC @ [Name] Initialize printer [Format] ASCII ESC @ Hex 1B 40 Decimal 27 64 [Range] None [Default] None [Description] The data in the print buf fer is cleared, and the printer mode(s) is reset to the mode that was in effect when the power was turned on.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS I [Name] Transmit print IS [Format] ASCII GS I n Hex 1D 49 n Decimal 29 73 n [Range] n = 2, 65 n 67, 80 n 81 [Default] No.
Command Descriptions Progr amming Reference VERSAJET MP3200 [Notes] With a serial interface printer , be sure to use this function when the host can receive data.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC L [Name] Select page mode [Format] ASCII ESC L Hex 1B 4C Decimal 27 76 [Range] None [Default] None [Description] Switches from standard mode to p age mode. [Notes] This command is only enabled when processed at the beginning of the line in standard mode.
Command Descriptions Progr amming Reference VERSAJET MP3200 In page mode, the printer print s the data in the print buf fer for the printing area specified by ESC W collectively by FF or ESC FF .
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC S [Name] Select standard mode [Format] ASCII ESC S Hex 1B 53 Decimal 27 76 [Range] None [Default] None [Description] Switches from page mode to st andard mode. [Notes] This command is only enabled in page mode.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( A [Name] Execute test print [Format] ASCII GS ( A pL pH n m Hex 1D 28 41 pL pH n m Decimal 29 40 65 pL pH n m [Range] ( pL + ( pH x 256)) = 2 ( pL = 2, pH = 0) [Description] Executes a specified test print.
Command Descriptions Progr amming Reference VERSAJET MP3200 When processing the automatic setting (m = 64) of the paper layout, the printer feeds the current roll paper to measure the p aper layout. During this time, the printer does not print.
Command Descriptions Progr amming Reference VERSAJET MP3200 RS G [Name] Draw line or square [Format] ASCII RS G n Hex 1E 47 n Decimal 30 71 n [Range] 1 n 2 [Default] None [Description] Draws line or square in page mode. If n = 1, draw a line.
Command Descriptions Progr amming Reference VERSAJET MP3200 RS s [Name] Print serial number [Format] ASCII RS s n1 nh Hex 1E 73 n1 nh Decimal 30 1 15 n1 nh [Range] nh Њ 0 [Default] n1 = 00, nh = 00 [Description] Prints serial number . [Notes] This command is only enabled in page mode.
Command Descriptions Progr amming Reference VERSAJET MP3200 RS W [Name] Clear printable area in page mode [Format] ASCII RS W xL xH yL yH dxL dxH dyL dyH Hex 1E 57 xL xH yL yH dxL dxH dyL dyH Decimal .
Command Descriptions Progr amming Reference VERSAJET MP3200 If the horizontal or vertical logical origin is set outside the print able area, this command is canceled, and the following data is processed as normal dat a.
Command Descriptions Progr amming Reference VERSAJET MP3200 RS b [Name] Battery check [Format] ASCII RS b Hex 1E 62 Decimal 30 98 [Range] None [Default] None [Description] Battery check, the return va.
Command Descriptions Progr amming Reference VERSAJET MP3200 RS m n [Name] Media length measurement setup [Format] ASCII RS m n Hex 1E 6D n Decimal 30 109 n [Range] 0 n 5 [Default] n = 0 [Description] Y ou can conduct length measurement by using transmissive sensor for gap label roll or reflective sensor for I-Mark media roll.
Command Descriptions Progr amming Reference VERSAJET MP3200 RS p [Name] Set printing copies of printing data [Format] ASCII RS p n Hex 1E 70 n Decimal 30 1 12 n [Range] 1 n 255 [Default] n = 1 [Description] Sets printing copies of printing dat a.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( K [Name] Select printing control [Description] Selects printing control as follows: Function is specified by the function code fn . fn Function 49 Function 49 Select s printing density pL and pH specify parameter number af ter fn to ( pL + pH x 256) bytes.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( K <Function 49> [Name] Selects printing density [Format] ASCII GS ( K pL pH fn m Hex 1D 28 4B 02 00 31 m Decimal 29 40 75 2 0 49 m [Range] ( pL + pH x 256) = 2 ( pL = 2, pH = 0 ) fn = 49, 0 m 15 [Default] m = 8 [Description] Selects printing control mode by m .
Command Descriptions Progr amming Reference VERSAJET MP3200 GS C 0 [Name] Select counter print mode [Format] ASCII GS C 0 n m Hex 1D 43 30 nm Decimal 29 67 48 nm [Range] 0 n 5, 0 m 2, .
Command Descriptions Progr amming Reference VERSAJET MP3200 [Notes] The serial number counter is stored in the print buffer by GS c . Settings of this command are effective until ESC @ is executed, the printer is reset, or the power is turned off.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS C 1 [Name] Select counter mode [Format] ASCII GS C 1 aL aH bL bH n r Hex 1D 43 31 aL aH bL bH n r Decimal 29 67 49 aL aH bL bH n r [Range.
Command Descriptions Progr amming Reference VERSAJET MP3200 [Notes] In a count-up setting, when the GS c is executed, the counter value exceeds the maximum value( bL + bH x 256), restart counting from the minimum value ( aL + aH x 256).
Command Descriptions Progr amming Reference VERSAJET MP3200 GS C 2 [Name] Select the serial number counter value [Format] ASCII GS C 2 nL nH Hex 1D 43 32 nL nH Decimal 29 67 50 nL nH [Range] 0 ( n.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS c [Name] Print counter [Format] ASCII GS c Hex 1D 63 Decimal 29 99 [Range] None [Default] None [Description] Sets the serial counter value in the print buffer and increment s or decrements the counter value.
Command Descriptions Progr amming Reference VERSAJET MP3200 The counter mode (count-up, count-down, count-stop) and details of counter (maximum value, minimum value, stepping amount of incrementing or decrementing of a counter value, the repetition number of printing) are set by GS C 1.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k [Name] S pecify and print the symbol [Format] ASCII GS ( k Hex 1D 28 6B Decimal 29 40 107 [Description] Processes the data concerning two-dimensional code. (PDF417, QR Code, MaxiCode).
Command Descriptions Progr amming Reference VERSAJET MP3200 cn fn Function 65 Function 765 Datamatrix: Specify the number of columns 66 Function 766 Datamatrix: Specify the number of rows 67 Function .
Command Descriptions Progr amming Reference VERSAJET MP3200 [Notes] The function is specified with the function code ( fn ). Details of the performance dif fer according to the function. For processing of PDF417 symbol dat a (w hen cn = 48) The symbol data specified by Function 080 d1 .
Command Descriptions Progr amming Reference VERSAJET MP3200 For process of QR Code symbol (when cn = 49) The symbol data specified by Function 080 d1 .
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k PDF417<Function 065> [Format] ASCII GS ( k pL pH cn fn n Hex 1D 28 6B 03 00 30 41 n Decimal 29 40 107 3 00 48 65 n [Range] ( pL.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k PDF417<Function 066> [Format] ASCII GS ( k pL pH cn fn n Hex 1D 28 6B 03 00 30 42 n Decimal 29 40 107 03 00 48 66 n [Range] ( p.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k PDF417<Function 067> [Format] ASCII GS ( k pL pH cn fn n Hex 1D 28 6B 03 00 30 43 n Decimal 29 40 107 03 00 48 67 n [Range] ( pL + pH x 256) = 3 ( pL =3 , pH =0 ) cn = 48 , fn = 67 1 n 5 [Default] n = 2 [Description] S pecifies the width of a module of PDF417 symbol.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k PDF417<Function 068> [Format] ASCII GS ( k pL pH cn fn n Hex 1D 28 6B 03 00 30 44 n Decimal 29 40 107 03 00 48 68 n [Range] ( pL + pH x256) = 3 ( pL =3, pH =0) cn = 48, fn = 68, 5 n 100 [Default] n = 5 [Description] Specifies the height of a module of PDF417 symbol.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k PDF417<Function 069> [Format] ASCII GS ( k pL pH cn fn m n Hex 1D 28 6B 04 00 30 45 mn Decimal 29 40 107 04 00 48 69 mn [Range].
Command Descriptions Progr amming Reference VERSAJET MP3200 The error correction code word calculated by modulus 929. Settings of this function are effective until ESC @ is executed, the printer is reset, or the power is turned off. 122 Preliminary Rev .
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k PDF417<Function 080> [Format] ASCII GS ( k pL pH cn fn m d1 dk Hex 1D 28 6B pL pH 30 50 30 d1 dk Decimal 29 40 107 pL pH 48 80 .
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k PDF417<Function 081> [Format] ASCII GS ( k pL pH cn fn m Hex 1D 28 6B 03 00 30 51 m Decimal 29 40 107 03 00 48 81 m [Range] ( pL + pH x 256) = 3 ( pL = 3, pH = 0) cn = 48, fn = 81 m = 48 [Description] Encodes and prints the PDF417 symbol dat a in the symbol save area.
Command Descriptions Progr amming Reference VERSAJET MP3200 The dat a area includes the following code words. Data specified by Function 080. The descriptor of symbol length (the first code word in the data area). The error correction code word calculated by modulus 929.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k QR Code<Function 165> [Format] ASCII GS ( k pL pH cn fn n1 n2 Hex 1D 28 6B 04 00 31 41 n1 n2 Decimal 29 40 107 04 00 49 65 n1 n.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k QR Code <Function 167> [Format] ASCII GS ( k pL pH cn fn n Hex 1D 28 6B 03 00 31 43 n Decimal 29 40 107 03 00 49 67 n [Range] ( pL + pH X 256) = 3 ( pL = 3, pH = 0) cn = 49, fn = 67 2 n 5 [Default] n = 2 [Description] S pecifies the size of a module of QR Code symbol.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k QR Code <Function 169> [Format] ASCII GS ( k pL pH cn fn n Hex 1D 28 6B 3 00 31 45 n Decimal 29 40 107 03 00 49 69 n [Range] ( pL + pH x 256) = 3 ( pL = 3, pH =0) cn = 49, fn = 69 48 n 51 [Default] n = 48 [Description] S pecifies the error correction level of QR Code.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k QR Code <Function 180> [Format] ASCII GS ( k pL pH cn fn m d1 dk Hex 1D 28 6B pL pH 31 50 30 d1 dk Decimal 29 40 107 pL pH 49 8.
Command Descriptions Progr amming Reference VERSAJET MP3200 Settings of this function are effective until the following processing is performed: Function 080 or 180 is executed. ESC @ is executed. The printer is reset or the power is turned off.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k QR Code <Function 181> [Format] ASCII GS ( k p pH cn fn m Hex 1D 28 6B 03 00 31 51 m Decimal 29 40 107 03 00 49 81 m [Range] ( .
Command Descriptions Progr amming Reference VERSAJET MP3200 The following data are added automatically by the encode processing. Position Detection Patterns Separators for Positio.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k MaxiCode<Function 265> [Format] ASCII GS ( k k pL pH cn fn n Hex 1D 28 6B 03 00 32 41 n Decimal 29 40 107 03 00 50 65 n [Range].
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k MaxiCode <Function 280> [Format] ASCII GS ( k pL pH cn fn m d1…dk Hex 1D 28 6B pL pH 32 50 30 d1…dk Decimal 29 40 107 pL pH.
Command Descriptions Progr amming Reference VERSAJET MP3200 [Data Format] Item Size and Type ANSI message header [ ]> <RS> Transportation Data Format Header 01 <GS> 96 Ship-To Postal Code 5 or 9 digits in the USA (mode2), up to 6 alphanumeric characters in other countries (mode3).
Command Descriptions Progr amming Reference VERSAJET MP3200 Notes: (1) RS and GS represents (1EH) and (1DH) respectively. (2) Background is yellow Æ Start / End elements (necessary) (3) Background is blue Æ data elements are mandatory (4) Each item finished adding “GS” 136 Preliminary Rev .
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k MaxiCode <Function 281> [Format] ASCII GS (k pL pH cn fn m Hex 1D 28 6B 03 00 32 51 m Decimal 29 40 107 03 00 50 81 m [Range] (.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k Datamatrix<Function 765> [Format] ASCII GS (k pL pH cn fn n Hex 1D 28 6B 03 00 37 41 n Decimal 29 40 107 03 00 55 65 n [Range] .
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k Datamatrix <Function 766> [Format] ASCII GS ( k pL pH cn fn n Hex 1D 28 6B 03 00 37 42 n Decimal 29 40 10703 00 55 66 n [Range] ( pL + pH x ҏ 256) = 3 ( pL = 3, pH =0 ) cn = 55 fn = 66 [Description] Specifies the number of rows of the data area of Datamatrix.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k Datamatrix <Function 767> [Format] ASCII GS ( k pL pH cn fn n Hex 1D 28 6B 03 00 37 43 n Decimal 29 40 107 03 00 55 67 n [Range.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k Datamatrix <Function 768> [Format] ASCII GS ( k pL pH cn fn n Hex 1D 28 6B 03 00 37 44 n Decimal 29 40 107 03 00 55 68 n [Range.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k Datamatrix <Function 769> [Format] ASCII GS ( k pL pH cn fn n Hex 1D 28 6B 04 00 37 45 n Decimal 29 40 107 04 00 55 69 n [Range] ( pL + pH x ҏ 256) = 3 ( pL = 4, pH =0 ) cn = 55 fn = 69 1 ҏ n ҏ 6 [Default] n = 6 [Description] Specifies the Data mode of Datamatrix.
Command Descriptions Progr amming Reference VERSAJET MP3200 Barcode type: Rectangle Shape Capacity Row Column number alphanumeric bytes 81 2 1 0 6 3 83 2 2 0 1 3 8 12 26 32 22 14 12 36 44 31 20 16 36 64 46 30 16 48 98 72 47 143 Preliminary Rev .
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k Datamatrix <Function 780> [Format] ASCII GS ( k pL pH cn fn m d1…dk Hex 1D 28 6B pL pH 37 50 30 d1…dk Decimal 29 40 107 pL .
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k Datamatrix <Function 781> [Format] ASCII GS ( k pL pH cn fn m Hex 1D 28 6B 03 00 37 51 m Decimal 29 40 107 03 00 55 81 m [Range] ( pL + pH x 256) = 3 ( pL = 3, pH = 0) cn = 55 fn = 81 m = 48 [Description] Encodes and prints the Datamatrix symbol data in the symbol save area.
Command Descriptions Progr amming Reference VERSAJET MP3200 The data area includes the following code words. Data specified by Function 780. The descriptor of symbol length (the first code word in the data area). The error correction code word calculated by modulus 929.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k RSS-14<Function 865> [Format] ASCII GS ( k pL pH cn fn n Hex 1D 28 6B 03 00 38 41 n Decimal 29 40 107 03 00 56 65 n [Range] ( pL + pH x 256) = 3 ( pL = 3, pH = 0) cn = 56 fn = 65 49 ҏ ҏ n ҏ ҏ 54 (Hex : 31~36) [Default] n = 49 [Description] Specify the mode of RSS-14.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k RSS-14<Function 866> [Format] ASCII GS ( k pL pH cn fn n Hex 1D 28 6B 03 00 38 42 n Decimal 29 40 107 03 00 56 66 n [Range] ( p.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k RSS-14<Function 867> [Format] ASCII GS ( k pL pH cn fn n Hex 1D 28 6B 03 00 38 43 n Decimal 29 40 107 03 00 56 67 n [Range] ( p.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k RSS-14<Function 868> [Format] ASCII GS ( k pL pH cn fn n Hex 1D 28 6B 03 00 38 44 n Decimal 29 40 107 03 00 56 68 n [Range] ( p.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k RSS-14<Function 880> [Format] ASCII GS ( k pL pH cn fn m d1…dk Hex 1D 28 6B pL pH 38 50 30 d1…dk Decimal 29 40 107 pL pH 56.
Command Descriptions Progr amming Reference VERSAJET MP3200 2D Composite Component CC-A capacity Æ 56 characters. CC-B capacity Æ 338 characters. For RSS-14 and RSS LIMIT, the printer automatically adds a check character at 14th digit when print.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k RSS-14<Function 881> [Format] ASCII GS ( k pL pH cn fn m Hex 1D 28 6B 03 00 38 51 m Decimal 29 40 107 03 00 56 81 m [Range] ( p.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k Code49<Function 967> [Format] ASCII GS ( k pL pH cn fn n Hex 1D 28 6B 03 00 39 43 n Decimal 29 40 107 3 00 57 67 n [Range] ( pL + pH x256) = 3 ( pL = 3, pH =0 ) cn = 57, fn = 67 1 n 255 [Default] n = 2 [Description] Specifies the width of narrow element.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k Code49<Function 968> [Range] ( pL + pH x 256) = 3 ( pL = 3, pH =0 ) [Format] ASCII GS ( k pL pH cn fn n Hex 1D 28 6B 03 00 39 44 n Decimal 29 40 107 3 00 57 68 n cn = 57, fn = 68 1 n 255 [Default] n = 16 [Description] Specify the height of one row.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k Code49<Function 980> [Format] ASCII GS ( k pL pH cn fn m d1 dk k bytes of d1 .
Command Descriptions Progr amming Reference VERSAJET MP3200 Data capacity Characters: The characters can’t exceed 49 bytes. Following characters will spend one byte, the others will spend two bytes.
Command Descriptions Progr amming Reference VERSAJET MP3200 Settings of this function are effective until the following processing is performed. For example: (1) “123ABC” ; Æ 6 bytes (2) “123abc” ; Æ 3 + 3*2 = 9 bytes Numeric Æ The numeric can’t exceed 81 bytes.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS ( k Code49<Function 981> [Format] ASCII GS ( k pL pH cn fn m There is no data (Function 980 is not processed).
Command Descriptions Progr amming Reference VERSAJET MP3200 GS h [Default] n = 162 [Name] Set bar code height [Format] ASCII GS h n Hex 1D 68 n Decimal 29 104 n [Range] 1 n 255 [Description] Sets the height of a bar code. n specifies number of dots in the vertical direction of a bar code.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS w [Name] Set bar code width [Format] ASCII GS w n Hex 1D 77 n Decimal 29 1 19 n [Range] 1 n 6 [Notes] This command setting is effective until ESC @ is ex ecuted, the printer is reset, or the power is turned off.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS k [Format] I. ASCII GS k m d1 dk NULL Hex 1D 6B m d1 dk NULL [Name] Print bar code Decimal 29 107 m d1 dk NULL I. II. ASCII GS k m n d1 dn Hex 1D 6B m n d1 dn Decimal 29 107 m n d1 dn [Range] I.
Command Descriptions Progr amming Reference VERSAJET MP3200 m Bar code system Number of data (k, n) Number of characters Characters Character code (d) 0 UPC-A Fixed 11 k 12 0~9 48 d 57.
Command Descriptions Progr amming Reference VERSAJET MP3200 [Notes] For I and II When standard mode is selected, this command is enabled only when the printing position is at the head of a line or when no data exist s in the print buffer . The bar code width that exceeds the printing area cannot be specified.
Command Descriptions Progr amming Reference VERSAJET MP3200 For UPC-A (m = 0, 65) process Modular check character is processed as follows: Automatically added when processing data is 1 1 byte. The 12th byte data is processed as a modular check character when processing dat a is 12 byte.
Command Descriptions Progr amming Reference VERSAJET MP3200 Prints a 6-column short code from 10 digit ( d2.d1 1 ) except NSC and modular check characters.
Command Descriptions Progr amming Reference VERSAJET MP3200 For JAN8/EAN8 (m = 3, 68) process Modular check character is processed as follows: Automatically added when processing data is 7 byte. The 8th byte data is processed as a modular check character when processing dat a is 8 byte.
Command Descriptions Progr amming Reference VERSAJET MP3200 For ITF (Interleaved 2 of 5) (m = 5, 70) process S tart code and stop code are added automatically . Check digits are not calculated and added. For CODEBAR (NW-7) (m = 6, 71) process S tart code and stop code are not added automatically .
Command Descriptions Progr amming Reference VERSAJET MP3200 For CODE128 ( m = 73) process Make sure to specify start character . The st art character must be code set selection character (any of CODE A, CODE B, or CODE C) which selects the first code set.
Command Descriptions Progr amming Reference VERSAJET MP3200 In CODE B, following data can be used. Character data: It is specified by ASCII code [in hexadecimal: 20H ~ 7FH / in decimal: 32~127] when specify "{", transmit “{{“ as 2 byte data (It is described sep arately).
Command Descriptions Progr amming Reference VERSAJET MP3200 Check digit is calculated and added automatically . S pecial character HRI is processed as follows: The printer does not print HRI characters that correspond to the shift character or code set selection character (CODE A, CODE B, or CODE C).
Command Descriptions Progr amming Reference VERSAJET MP3200 GS H [Name] Select printing position of Human Readable Interpretation (HRI) characters [Format] ASCII GS H n Hex 1D 48 n Decimal 29 72 n [Ra.
Command Descriptions Progr amming Reference VERSAJET MP3200 GS f [Name] Select font for HRI characters Font of HRI characters [Format] ASCII GS f n Hex 1D 66 n Decimal 29 102 n [Range] n = 0, 1 , 48, .
Command Descriptions Progr amming Reference VERSAJET MP3200 FS q [Name] Define image, write to flash memory [Format] ASCII FS q n [xL xH yL yH d1 dk] 1 [xL xH yL yH d1 dk] n Hex 1C 71 n [xL xH yL yH d.
Command Descriptions Progr amming Reference VERSAJET MP3200 [Notes] Paper cannot be fed by using P APER FEED button. dY+1 NV bit image means a bit image which is defined in a non-volatile memory . The NV bit image defined is effective until the next NV bit image is defined.
Command Descriptions Progr amming Reference VERSAJET MP3200 Data is written to the non-volatile memory by this command. Note the following when using this command. The printer is BUSY when writing the data to the non-volatile memory . In this case, be sure not to transmit data from the host because the printer does not receive dat a.
Command Descriptions Progr amming Reference VERSAJET MP3200 FS p [Name] Read the image file from flash memory [Format] ASCII FS p n m Hex 1C 70 n m Decimal 28 1 12 n m [Range] 1 n 255 0 m 3, 48 m 51 [Description] Prints a NV bit image n using the mode specified by m .
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC ESC 00 [Name] Communication parameter setup (RS232C or IrDA) [Format] ASCII ESC ESC 00; n , n1 n2 n3 n4, n5 , n6 , n7 , n8 , n9 , n10 , .
Command Descriptions Progr amming Reference VERSAJET MP3200 n10 n5 : Data Length (8 bit s, fixed) n6 : Parity (N, fixed) n7 : S t op Bit (1bit, fixed) n8 : Communication Protocol R Ш R TS/CTS(hardware, use R as a dummy even for IrDA) X Ш Xon/Xoff(sof tware) n9 : Reserve(value:00) : Reserve(value:00) n1 1 : Reserve(value:00) 179 Preliminary Rev .
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC ESC 04 [Name] Printing Mode Change [Format] ASCII ESC ESC 04 n Hex 1B 1B 04 n Decimal 27 27 04 n [Range] 0 n 1 [Default] n = 0 [Description] Set up printing mode, using n as follows: n Function 0 S tandard (line) mode 1 Page mode 180 Preliminary Rev .
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC ESC 05 [Name] Printer ID (for IrDA only) [Format] ASCII ESC ESC 05 nh n1 Hex 1B 1B 05 nh n1 Decimal 27 27 05 nh n1 [Range] 0 nh 255 0 n1 255 [Default] nh = 00 n1 = 01 [Description] Prints ID (for IrDA only).
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC ESC 07 [Name] Adjust label printing position [Format] ASCII ESC ESC 07 nn 1 Hex 1B 1B 07 nn 1 Decimal 27 27 07 nn 1 [Range] n = “+” or “-” 0 n1 160 (0.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC ESC 08 [Range] 0 n 1 Function [Name] Setup sensor [Format] ASCII ESC ESC 08 nn 1 Hex 1B 1B 08 nn 1 Decimal 27 27 08 nn 1 0 n.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC ESC 09 [Name] Setup power off time [Range] 1 n 255 [Notes] If the power is on, and the printer has had no action for n minutes, then, the printer will be automatically off.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC ESC 10 [Name] Define printing intensity [Format] ASCII ESC ESC 10 n Hex 1B 1B 0A n Decimal 27 27 10 n [Range] 0 n 15 [Default] n = 8 [Description] Defines printing intensity . The more of n , the more intensity .
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC ESC 1 1 [Range] 0 n 2 n [Name] Define the using port of IrDA [Format] ASCII ESC ESC 1 1 n Hex 1B 1B 0B n Decimal 27 27 1 1 n [De.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC ESC 12 [Name] On-demand Setup [Range] 1 n 2 [Format] ASCII ESC ESC 12 n Hex 1B 1B 0C n Decimal 27 27 12 n [Default] n = 1 [Description] Setup auto linefeed, using n as follows: n Function 1 Motor will not move back 2 Motor will move back and forward 187 Preliminary Rev .
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC ESC 13 [Name] Setup radio off time [Format] ASCII ESC ESC 13 n Hex 1B 1B 0D n Decimal 27 27 13 n [Range] 1 n 255 [Default] n = 20 [Description] Setup radio off time, the unit is minutes.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC ESC 14 [Name] Define IrDA protocol [Format] ASCII ESC ESC 14 n Hex 1B 1B 0E n Decimal 27 27 14 n [Range] 01 n 02 [Default] n = 01 [Description] Defines IrDA protocol 01: IrOBEX 02: IrCOMM [Notes] The maximum limit of file which transmits through IrDA protocol is 8K.
Command Descriptions Progr amming Reference VERSAJET MP3200 ESC ESC D [Name] Restore default value [Format] ASCII ESC ESC D Hex 1B 1B 44 Decimal 27 27 68 [Range] None [Default] None [Description] Restores all default values.
Ein wichtiger Punkt beim Kauf des Geräts Cino MP3200 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Cino MP3200 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Cino MP3200 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Cino MP3200 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Cino MP3200 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Cino MP3200 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Cino MP3200 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Cino MP3200. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Cino MP3200 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
