Benutzeranleitung / Produktwartung CX60 des Produzenten Christie Digital Systems
Zur Seite of 79
RPMX/CX50/CX60/CX67 User’s Manual Table of Contents 013-100162 Rev .1 (07/05) NOTE: Due to constant research, the information in this manual is subject to change without notice Contents Page 1.1 Overview..............................................
Section 1 Introduction RPMX/CX50/CX60/C X67 User’s Manual 1- 1 The GraphXMASTER X -series include s the RPMX- 100U (38-GFX101- xx), CX50-100U (38- GFX003-xx), CX60- 100U (38-GFX004-xx) and CX6 7-100U (38-GFX005- xx). All of th ese products are based on single- chip DLP (D ig it al Light Proc essing) techno logy with XGA resolution.
Section 1: I ntroducti on 1-2 RPMX/CX50/C X60/CX67 User’s M anual How the projecto r works The proje ctor opera tes base d on DLP tech nol ogy by Te xas In str umen ts . An external so urce prov ides th e necessa ry XGA input signals accepted by the projector.
Section 1: I ntroducti on RPMX/CX50/CX60/C X67 User’s Manual 1- 3 Whether th e projecto r is under wa rranty or the warra nty has expi red, Christ ie’s highly trained and e xtensiv e facto ry and deale r service network is always availab le to quick ly diagno se and cor rect pro jector m alfunction s.
.
Section 2 Source Setup RPMX/CX50/CX60 /CX67 User’s Manua l 2-1 This sec tion prov ides deta ils on how to con nect v arious ext ernal sour ces to the projector. A ll conne ctions a re m ade to the main inpu t panel of the E lectr oni cs Module (E M).
Section 2: Sou rce Setup 2-2 RPMX/CX50/C X60/C X67 User’s Manua l Connect Analog VGA signals to the 15- pin HD D- sub connector on the s econd input in terface. F igure 2.2. Figure 2.2. Analog VGA Connector The second input in terface is dedica ted to d igital v ideo input sig nals c onform ing to the DVI (Dig ital Vi sual In terface) standard.
Section 2: Sou rce Setup RPMX/CX50/CX60 /CX67 User’s Manual 2- 3 Figure 2.4. Loop Digital Video Input Signals Connect a com posite video input to the Com posite RCA jack labeled I N. The jack ad jacent to i t is left em pty, unle ss you want to loop the composit e video signal through to th e next d isplay dev ice.
Section 2: Sou rce Setup 2-4 RPMX/CX50/C X60/C X67 User’s Manua l Composite Video Loo p Through From y our source, connect a composit e vi deo sour ce sig nal to the Com posite IN RCA jack. Take a seco nd cable and connect it from the em pty RCA jack labele d Composite OUT to the Com posite IN connector of th e next proje ctor.
Section 2: Sou rce Setup RPMX/CX50/CX60 /CX67 User’s Manual 2- 5 Figure 2.8. S-Video Loop Through There are two, 9- pin DI N connectors on the input pane l dedicated to seria l comm unication.
Section 2: Sou rce Setup 2-6 RPMX/CX50/C X60/C X67 User’s Manua l Figure 2.10. Multiple Pro jector RS-232 Connection Figure 2.11. Multiple Pro jector RS232 Communic ation Schematic Figure 2.
Section 2: Sou rce Setup RPMX/CX50/CX60 /CX67 User’s Manual 2- 7 There are two AC r eceptacl es on the EM. To plug in a single pro jector, plug the power cord into the to p AC receptacl e (labeled I NLET). Then plug the 3- pronged end of the power cord into a grounded AC outl et.
.
Section 3 Operation RPMX/CX50/CX60/CX67 User’s Manual 3- 1 This sec tion prov ides a gen eral de scription of the pro jector’s m ain com ponents. I t also prov ides deta ils on the projector ’s softw are menu s ystem .
Section 3: Ope ration 3-2 RPMX/CX50/C X60/CX67 User’s M anual The EM is the main co ntrol unit of the pro jector. I t is m ounted independ ently from the PHM to the m ounting tray . I t is the m odule where all sourc e connections are made an d where the m ain power sw itch is loc ated.
Section 3: Ope ration RPMX/CX50/CX60 /CX67 User’s Manua l 3-3 The proje ctor is con trolled by an IR remote k eypad that is supplied in the User’ s Kit. It is op erated by 2 AA batteries and p rovide s wireless cont rol of the projector from up to 1 00 feet away .
Section 3: Ope ration 3-4 RPMX/CX50/C X60/CX67 User’s M anual NOTES: 1) Avoid tur ning the pro jector on and off wit hout waiting a t least 52 seconds in be tween.
Section 3: Ope ration RPMX/CX50/CX60 /CX67 User’s Manua l 3-5 PROJECTOR Press Proj ector to access opt ions fo r comm unication with a specific p rojector o r all pro jectors w ithin a n etwork . All Pr oject ors – You can toggle the setting for th is option usi ng the En te r key.
Section 3: Ope ration 3-6 RPMX/CX50/C X60/CX67 User’s M anual Most of the controls for the pro jec tor are acc ess ed fro m within the proje cto r’ s menu sy stem. The Ma in M enu i s accessib le by press ing the Me nu key o n th e remote k eypad.
Section 3: Ope ration RPMX/CX50/CX60 /CX67 User’s Manua l 3-7 DIRECT SLIDEBARS There are a set of d irect ke ys avail able on the k eypad th at allow y ou to quickly access oft en used sl idebars with out hav ing to tr avel the m enu system .
Section 3: Ope ration 3-8 RPMX/CX50/C X60/CX67 User’s M anual Use the opt ions in the Size and Position menu (Fig ure 3.4.) to adjus t the size of the display ed image so that it fits the screen to best suit the appl ication. Ot her related op tions, su ch as Pixe l Tr ack and Pix el Phas e a re used to re fine the imag e.
Section 3: Ope ration RPMX/CX50/CX60 /CX67 User’s Manua l 3-9 NO RESIZING Select No Resizi ng to d isplay the imag e in its nat ive re solution. The valu es for the options in the top lev el Size and Position m enu will change according ly. Figure 3.
Section 3: Ope ration 3-10 RPMX/CX50/C X60/CX67 User’s M anual Tilin g Full S creen, T iling Full W idth, Tiling Full Height and Tili ng Anamorphic . These opt ions are es sentially the sam e as the ones descr ibed above except they expand across disp lays in the defined ar ray.
Section 3: Ope ration RPMX/CX50/CX60 /CX67 User’s Manua l 3-11 to the po int wher e one larg e stripe fills the im age. Ag ain, the im age m ay still exhibit some nois e. NOTE: 1) By defaul t, the proje ctor will sample at the correct fr equency for most sources.
Section 3: Ope ration 3-12 RPMX/CX50/C X60/CX67 User’s M anual Contrast Select Contrast when you want to incre ase or decr ease the per ceived diffe rence between lig ht and dark areas of y our im age (0-255). I f contrast is set too h i gh, the light pa rts of th e imag e loses detai l and clar ity.
Section 3: Ope ration RPMX/CX50/CX60 /CX67 User’s Manua l 3-13 test patt ern is disp layed. N OTES: 1) This opt ion is onl y available wh en using a video sou rce. 2) This option is not a vailable wh en using an in ternal test pattern. DETAIL Detail adjusts the sharpne ss of the v ideo im age.
Section 3: Ope ration 3-14 RPMX/CX50/C X60/CX67 User’s M anual To create or adjust a user defined (custom) color temperatu re: NOTE: Use an externa l test pattern wh en adjus ting col or temperature . (Figure 3.13.) 1. Select User1 or User 2 and adjust Red, Green and Blu e slidebars unt il the desired color temperatu r e is ac hieved.
Section 3: Ope ration RPMX/CX50/CX60 /CX67 User’s Manua l 3-15 “crushed ” nor excess ively elevated. By defau lt, the pro jecto r autom atically determ ines the co rrect se tting according to th.
Section 3: Ope ration 3-16 RPMX/CX50/C X60/CX67 User’s M anual BLACK LEVELS & INPU T DRIVES An experienced u ser can m anually ad just the bla ck lev els and inpu t drives fo r a s ourc e that ex hibi ts hi gh bla ck l evels . By a dju stin g the sli deba rs her e, you can refine the im age source inpu t lev els.
Section 3: Ope ration RPMX/CX50/CX60 /CX67 User’s Manua l 3-17 White Boost This opti on allow s you to recap ture som e of the los t lig ht from the tran sitio n between seg ments in the co lor wheel wh en it is spinnin g. U se the slideba r to increase t he value of White Boost from 0 to 10.
Section 3: Ope ration 3-18 RPMX/CX50/C X60/CX67 User’s M anual From the Conf iguration m enu, you can acces s various options and subm enus that allow you to cu stomiz e how y ou view and use your p rojector, suc h as menu location and lang uage. You can also assign a pro jector ID num ber and define its location in a mu ltiple dis play wall.
Section 3: Ope ration RPMX/CX50/CX60 /CX67 User’s Manua l 3-19 Menu Preference Select thi s option when y ou want t he menus to appear i n a differe nt locat ion on the screen.
Section 3: Ope ration 3-20 RPMX/CX50/C X60/CX67 User’s M anual PROJECTOR ID Use this op tion to se t a specif ic 2-dig it ID number for the p rojector. I n a network env ironm ent, having the ability to control one or all p rojectors i s very important.
Section 3: Ope ration RPMX/CX50/CX60 /CX67 User’s Manua l 3-21 start nu mbering in the top- left corner (this display will be 1,1) and work across an d down until y ou reach the bottom right cor ner.
Section 3: Ope ration 3-22 RPMX/CX50/C X60/CX67 User’s M anual Diagnostics & Service Select thi s submenu to access v arious interna l test patt erns and/o r freeze the display ed imag e for diagno stic and se tup purpo ses. TEST PATTERN Nine interna l test pa tterns a re availab le from this m enu.
Section 3: Ope ration RPMX/CX50/CX60 /CX67 User’s Manua l 3-23 At any tim e during operatio n you can selec t the Lamp Menu to view the number of hours the lam p has been in us e.
Section 3: Ope ration 3-24 RPMX/CX50/C X60/CX67 User’s M anual Figure 3.33. This is a read- only window acce ssible f rom the Ma in menu that lists sy stem inform ation, such as projec tor m odel and seria l number, pro jector I D, current input sou rce, resol ution, fre quencies and c urrent so ftware v ersion.
Section 3: Ope ration RPMX/CX50/CX60 /CX67 User’s Manua l 3-25 There are two m ethods of c omm unicating wit h multip le pro jectors, us ing the I R key pad or RS-232 serial co mm unication.
Section 3: Ope ration 3-26 RPMX/CX50/C X60/CX67 User’s M anual Use the Tiling Setup s ubmenu to d efine the siz e of a w all (num ber of rows and columns), an d ident ify the l ocation of e ach projec tor in the w all. I f you are operating a stand- alone unit , enter “1” f or item s 1 to 4.
Section 3: Ope ration RPMX/CX50/CX60 /CX67 User’s Manua l 3-27 • Wait for the 6 valu es (black levels and d r ives) to stabi lize. • Leave the Input Level s menu.
Section 3: Ope ration 3-28 RPMX/CX50/C X60/CX67 User’s M anual 4c) Adjust c olor t emperatu re to match whit es bet ween screen s (keep Whit e Bo ost at 0) – View al l white field s and adjus t Red, Green, Blue in the Color Temperature window.
Section 3: Ope ration RPMX/CX50/CX60 /CX67 User’s Manua l 3-29 attention o f a quali fied serv ice technician. The specif ic patter n of flash ing indicates the 2- digit code identify ing the ty pe of problem encountered— the number of y ellow flashe s repres ents th e first dig it and the num ber of red flashe s indicates the seco nd digit.
.
Section 4 Maintenance RPMX/CX50/CX60/CX67 User’s Manual 4- 1 The proje ctor is an internat ional reg ulatory agency approved produ ct des igned for safe and reliabl e operati on. To assure com plete safety at all tim es it is importan t to ack nowledge the fo llowing precaution s while opera ting the projector.
Section 4: M aintenance and Troub leshooting 4-2 RPMX/CX50/C X 60/C X67 User’s Manua l stops, exc essive fo rce, and unev en surfaces may cause the pro jector and c art combinati on to ov erturn. The proje ctor is desig ned to oper ate with a 120W UHP lam p.
Section 4: Main tenance and Troub leshooting RPMX/CX50/CX60 /CX67 User’s Manua l 4-3 Slots and ven t s in th e projector provide v entilation. Nev er block or c over th ese openings. This ensu res reli able oper ation of th e pro jector and prev ents overheating .
Section 4: M aintenance and Troub leshooting 4-4 RPMX/CX50/C X 60/C X67 User’s Manua l The key pad works on 2 AA siz e alkaline ba tteries. P eriodically these batte ries require replacem ent. To replace batt er ies : 1. Turn the k eypad ov er to access the sm all battery compartment c over.
Section 4: Main tenance and Troub leshooting RPMX/CX50/CX60 /CX67 User’s Manua l 4-5 STEP 1 – Power down the pr ojector and unplu g – Press Powe r to turn t he projector o ff.
Section 4: M aintenance and Troub leshooting 4-6 RPMX/CX50/C X 60/C X67 User’s Manua l Figure 4.3. (b) Firmly , grasp the lamp m odule and pull st raight out. Keep th e lamp level when doing this so tha t it easily disconnects from the term inal block.
Section 4: Main tenance and Troub leshooting RPMX/CX50/CX60 /CX67 User’s Manua l 4-7 The proje ction lens can be ad justed to focu s a disp layed im age. Typically, the projection lens on ly require s focusi ng during th e insta llation and setup o f the projector.
Section 4: M aintenance and Troub leshooting 4-8 RPMX/CX50/C X 60/C X67 User’s Manua l Use the fo llowing as a guid e in iden tifying general o perating problem s, the cause and how they can b e corre cted. Most of these prob lems can be corrected by a user and do not requi re the assist ance of a qua lified t echnician.
Section 4: Main tenance and Troub leshooting RPMX/CX50/CX60 /CX67 User’s Manua l 4-9 The display is jittery or unstable… 1. If the disp lay is jittery , or if it d isappea rs and reap pears err atically check that the source i s properly connected and that its signa l is of ade quate qual ity for detection.
Section 4: M aintenance and Troub leshooting 4-10 RPMX/CX50/C X60/CX67 User’s M anual The display is not sharp or clean… 1. More displ ay adjustm ents may be required – focus, b rightnes s, contrast, pix el track ing, and pixel p hase. 2. If you are us ing a BNC T- connector, try using a di stributio n amplif ier to boost sig nal level s.
Section 5 Specifications RPMX/CX50/CX60 /CX67 User’s Manual 5- 1 NOTES: 1 ) Due to c ontinui ng research, specific ations are s ubjec t to change w ithout notice. 2) Spe cification s apply to all m odels unless o therwise no ted. 3) CX50 /CX60 data with use of High Gai n screen an d CX67 with Wid e Angle screen.
Section 5: Spe cification s 5-2 RPMX/CX50/C X60/C X67 User’s Manua l Sync (interlaced or progressive scan for mats) Horizontal freq uency rang e 15-85 kHz Vertica l frequency rang e 50-85Hz Scan for.
Section 5: Spe cification s RPMX/CX50/CX60 /CX67 User’s Manual 5- 3 FOR CX50-100U Horizontal ± 38 degrees ± 2.0 degrees Vertica l ± 9.5 degrees ± 1.0 degree s FOR CX60-100U Horizontal ± 25 degrees ± 3.0 degrees Vert ica l ± 9 degrees ± 1.0 degrees FOR CX67-100U Horizontal ± 35 degrees ± 3.
Section 5: Spe cification s 5-4 RPMX/CX50/C X60/C X67 User’s Manua l NOTE: 1) Dimensions ap ply to all mo dels, unles s specified o t herwis e. 2) Screen dimensions can vary based on environmen tal condi tions.3) All dimension s in inche s and for re ference on ly.
Section 5: Spe cification s RPMX/CX50/CX60 /CX67 User’s Manual 5- 5 Size (includes lens, adjus ter and mountin g rails) Lens Horizonta l Configurat ion (0 degree ) Lens Vert ical Configura tion (90 .
Section 5: Spe cification s 5-6 RPMX/CX50/C X60/C X67 User’s Manua l Weight ( without sc reen, to p cover, pedest al and packag ing) 125lb. Size Weight ( without sc reen, to p cover, pedest al and packag ing) 150lb.
Section 5: Spe cification s RPMX/CX50/CX60 /CX67 User’s Manual 5- 7 Weight ( without sc reen, to p cover, pedest al and packag ing) 171lb. Size CAN/CSA C22.2 No. 60950- 00 ANSI/UL 60950 3 rd Editio n EN60950: 2000 Eu ropean Norm , Safety of I nformation Technolog y Equipm ent Electro- Magneti c Compatib ility (E.
Section 5: Spe cification s 5-8 RPMX/CX50/C X60/C X67 User’s Manua l • User ’s Kit (38-804828-01 f or RPMX) and (38-8048 29-02 for CX50 / CX6 0 / CX67) , includes user/insta llation m anuals, IR.
Appendix A Glossary RPMX/CX50/CX60 /CX67 User’s Manual A- 1 This append ix defines the s pecific term s used in this manual as they app l y to th is projector. A l so inc luded are other gener al term s commonly used in the p rojection industry . The tim e, inside one hor izontal sc an line, dur ing which v ideo is genera ted.
Appendix A: Glo ssary A- 2 RPMX/CX50/CX60/CX67 User ’s Manual A menu item that indicates whethe r an option is cur rently in e ffect (c hecked) or no t (uncheck ed). A change in the tin t of a wh ite field across an im age. The color ation (reddis h, white, bluish, green ish, etc.
Appendix A: Glo ssary RPMX/CX50/CX60 /CX67 User’s Manua l A-3 A display of help info rmati on regard ing the cur rent tas k or present ation. The frequency at which s can lines a re gene rated, wh ich v aries am ongst sources. Also called hor izontal sc an rate or line ra te.
Appendix A: Glo ssary A- 4 RPMX/CX50/CX60/CX67 User ’s Manual A list o f selectable o ptions displayed on the screen. A video output format of som e video tape and di sk play ers. There are two types o f NTSC (Nati onal Telev ision Stand ards Comm ittee) video: N TSC 3.
Appendix A: Glo ssary RPMX/CX50/CX60 /CX67 User’s Manua l A-5 The video ou tput (ana log or dig ital) of mo st compute rs. Analog RGB v ideo can hav e 3, 4, or 5 wires — one each for red, gre en, and blue, an d either none, one o r two for sync. For thre e-wire RGB, t he green wire u sually prov ides sync.
Appendix A: Glo ssary A- 6 RPMX/CX50/CX60/CX67 User ’s Manual The ab ility of a projecto r to synchroniz e to inpu ts with freq uencies within a specifi ed range. The freque ncy at which images are g enera ted. Vertic al freq uencies v ary am ongst sources.
Appendix B Acceptable Signal Types RPMX/CX50/CX60 /CX67 User’s Manual B- 1 Format Ty pe Mode H. Freq V. Freq Input Resoluti on Sync polarity Scan Type Input Term inal NTSC@RGBHV NTSC 15.734 59.94 N/N Interlaced RGB IN PAL/SECAM @RGBHV PAL 15.625 50.
Appendix B: S ignal Types B- 2 RPMX/CX50/CX60/C X67 User’s Manua l Format Ty pe Mode H. Freq V. Freq Input Resoluti on Sync polarity Scan Type Input Term inal VESA 800X600 @85Hz SVGA85 53.67 4 85.061 800X600 P/P Non-Interlaced R GB IN MacIntosh 16inch Mode @75Hz MAC16 49.
Appendix B: S ignal Types RPMX/CX50/CX60 /CX67 User’s Manua l B-3 Mod e Input Res. A Pixel B C D E FH KHz fV Hz Clock MHz G Line H I J K NTSC 15.734 59.94 16.521 PAL 15.625 50 16. 406 HDTV 33.75 60 67.264 NEC24k 640X400 85 640 59 64 848 24.82 55.9 21.
.
Appendix C Keypad Reference RPMX/CX50/CX60 /CX67 User’s Manua l C-1.
.
Appendix D Serial Communication Cables RPMX/CX50/CX60 /CX67 User’s Manual D- 1 When connect ing pro jector to a c omputer o r another p rojector use the app ropriate serial comm unication shie lded cabling as illustrat ed.
Appendix D: Seri al Comm unication Cables D- 2 RPMX/CX50/CX60/CX67 User’s Manua l.
Appendix E Menu Tree RPMX/CX50/CX60 /CX67 User’s Manual E- 1.
.
Index RPMX/CX50/CX60 /CX67 User’s Manual 6 6-Axis Adjuster, 3- 2 A Adjust Prim ary Colors, 3- 21 Arrow Keys, 3-4 Auto Input Lev els, 3-17 Auto Setup, 3- 17, 3-24 B Baud Rate, 3-19 Black lev el, 3-16.
Index Menu Preferenc es , 3- 19 Mode Memory Status , 3-17 P Pixel Key, 3- 5 Pixel Phase , 3-1 1 Pixel Tracking , 3-10 Position Key , 3-5 Power Connection, 2-7 Power Cords, 4- 2 Power Level Switching ,.
Ein wichtiger Punkt beim Kauf des Geräts Christie Digital Systems CX60 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Christie Digital Systems CX60 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Christie Digital Systems CX60 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Christie Digital Systems CX60 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Christie Digital Systems CX60 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Christie Digital Systems CX60 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Christie Digital Systems CX60 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Christie Digital Systems CX60. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Christie Digital Systems CX60 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
