Benutzeranleitung / Produktwartung PD300DM des Produzenten Chamberlain
Zur Seite of 40
The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1 196 www .chamberlain.com GARAGE DOOR OPENER Model PD300DM • 1/2 HP For Residential Use Only ® ® Owner’ s Manual ■ Please read this manual and the enc losed safety materials carefully! ■ Fasten the man ual near the garage door after installation.
2 T ABLE OF CONTENTS When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury or death if you do not comply with the warnings that accompany them. The hazard may come from something mechanical or from electric shock.
3 To prevent damage to garage door and opener: • ALWAYS disable locks BEFORE installing and operating the opener. • ONLY operate garage door opener at 120V, 60 Hz to avoid malfunction and damage. To prevent possible SERIOUS INJURY or DEATH: • ALWAYS call a trained door systems technician if garage door binds, sticks, or is out of balance.
4 Safety Reversing Sensor Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.). See page 23 for details. — — — — — — — — Header W all Safety Reversing Sensor Gap between floor and bottom of door must not exceed 1/4" (6 mm).
5 Access Door Safety Reversing Sensor Safety Reversing Sensor Gap between floor and bottom of door must not exceed 1/4" (6 mm). Door Bracket Straight Door Arm Garage Door CLOSED POSITION Header B.
6 2-Conductor Bell Wire White & White/Red Chain and Cable in Dispensing Carton Curved Door Arm Section Straight Door Arm Section Safety Labels and Literature Hanging Brackets Door Bracket (2) Safe.
7 Wing Nut 1/4"-20 (2) Handle Nut 5/16"-18 (8) Ring Fastener (3) Spacer (2) Carriage Bolt 1/4"-20x1/2" (2) Insulated Staples (30) Rope Lock W asher 5/16" (7) Lag Screw 5/16&qu.
FRONT RAIL (TOP) KEEP LARGER HOLE ON TOP 8 ASSEMBL Y STEP 1 Assemble the Rail & Install the T rolley T o av oid installation difficulties, do not run the garage door opener until instructed to do so.
9 To avoid SERIOUS damage to garage door opener, use ONLY those bolts/fasteners mounted in the top of the opener. ASSEMBL Y STEP 2 Fasten the Rail to the Motor Unit • Insert a 1/4"-20x1-3/4 bolt into the cover protection bolt hole on the back end of the rail as shown.
10 To avoid possible SERIOUS INJURY to fingers from moving garage door opener: • ALWAYS keep hand clear of sprocket while operating opener. • Securely attach chain spreader BEFORE operating. Leave Chain and Cable Inside Dispensing Carton to Prevent Kinking.
11 INST ALLA TION ASSEMBL Y STEP 5 Tighten the Chain • Spin the inner nut and lock washer down the trolley threaded shaft, away from the trolley . • T o tighten the chain, turn outer nut in the direction shown (Figure 1).
12 INST ALLA TION STEP 1 Determine the Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door . 1. Close the door and mark the inside vertical centerline of the garage door .
13 Lag Screws 5/16"x9x1-5/8" – Finished Ceiling – Door Spring Header Wall UP Ceiling Mounting Holes 6" (15 cm) Maximum Header Bracket Vertical Centerline of Garage Door Garage Door .
14 Opener Carton or Temporary Support Garage Door OPTION WITH SOME EXISTING INSTALLATIONS Header Bracket Idler Pulley Header Wall Header Bracket Mounting Hole Existing Header Bracket Spacer Mounting H.
15 ONE-PIECE DOOR WITHOUT TRA CK A 2x4 on its side is convenient for setting an ideal door-to-rail distance. • Remove foam packaging. • Raise the opener onto a stepladder .
16 INST ALLA TION STEP 5 Hang the Opener Three representative installations are shown. Y ours may be different. Hanging brackets should be angled (Figure 1) to provide rigid support. On finished ceilings (Figure 2 and Figure 3), attach a sturdy metal bracket to structural supports before installing the opener .
17 To prevent possible SERIOUS INJURY or DEATH from electrocution: • Be sure power is not connected BEFORE installing door control. • Connect ONLY to 24 VOLT low voltage wires.
18 INST ALLA TION STEP 7 Install the Light • Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens. • Install up to a 100 watt maximum light bulb in the socket.
19 INST ALLA TION STEP 9 Electrical Requirements T o av oid installation difficulties, do not run the opener at this time. T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet.
20 Invisible Light Beam Protection Area Safety Reversing Sensor 6" (15 cm) max. above floor Safety Reversing Sensor 6" (15 cm) max. above floor Facing the door fr om inside the garage INST A.
21 DOOR TRACK MOUNT (RIGHT SIDE) Indicator Light Lens Lip Sensor Brack et Door T rack FLOOR MOUNT (RIGHT SIDE) W ALL MOUNT (RIGHT SIDE) Indicator Light Sensor Brack et Lens Extension Brack et (See Acc.
22 Carriage Bolt 1/4"-20x1/2" Lens Wing Nut 1/4"-20 Figure 5 MOUNTING AND WIRING THE SAFETY REVERSING SENSORS • Slide a 1/4"-20x1/2" carriage bolt head into the slot on each sensor . Use wing nuts to fasten sensors to brackets, with lenses pointing toward each other across the door .
Door Bracket V ertical Centerline of Garage Door UP V ertical Reinforcement Self-Threading Screw 1/4"-14x5/8" 23 Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket. Contact your door manufacturer for reinforcement kit.
24 Header W all V ertical Centerline of Garage Door Finished Ceiling Optional Placement of Door Bracket Header Bracket Door Bracket 2x4 Support For a door with no exposed framing, or for the optional installation, use lag screws 5/16"x1-1/2" (Not Provided) to fasten door bracket.
25 INST ALLA TION STEP 12 Connect Door Arm to T rolley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONL Y • Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley .
26 ALL ONE-PIECE DOORS 1. Assemble the door arm, Figure 4: • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). • With the door closed, connect the straight door arm section to the door bracket with the 5/16"x1-1/4" clevis pin.
27 ADJUSTMENT STEP 1 Adjust the UP and DOWN T ravel Limits Limit adjustment settings regulate the points at which the door will stop when moving up or down. T o operate the opener , press the Door Control push bar . Run the opener through a complete travel cycle.
28 ADJUSTMENT STEP 2 Adjust the Force Force adjustment controls are located on the back panel of the motor unit. Force adjustment settings regulate the amount of power required to open and close the door . If the forces are set too light, door travel may be interrupted by nuisance reversals in the down direction and stops in the up direction.
29 Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. • Safety reversal system MUST be tested every month. • If one control (force or travel limits) is adjusted, the other control may also need adjustment.
30 OPERA TION Using Y our Garage Door Opener Y our Security ✚ ® opener and hand-held remote control have been factory-set to a matching code which changes with each use, randomly accessing over 100 billion new codes. Y our opener will operate with up to eight Security ✚ ® remote controls and one Security ✚ ® Keyless Entry System.
31 T o Open the Door Manually DISCONNECT THE TROLLEY : The door should be fully closed if possible. Pull down on the emergency release handle (so that the trolley release arm snaps into a vertical position) and lift the door manually .
32 CARE OF YOUR OPENER LIMIT AND FORCE ADJUSTMENTS: Weather conditions may cause some minor changes in door operation requiring some re-adjustments, particularly during the first year of operation. Pages 27 and 28 refer to the limit and force adjustments.
33 HA VING A PROBLEM? (TROUBLESHOOTING) 1. My door will not close and the light bulbs b link on m y motor unit: The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. • V erify the safety sensors are properly installed, aligned and free of any obstructions.
34 Installed Safety Reversing Sensor Safety Reversing Sensor Bell Wire Diagnostics Located On Motor Unit LED or Diagnostic LED "Learn" Button Y our garage door opener is programmed with self-diagnostic capabilities. The “Learn” button/diagnostic LED will flash a number of times then pause signifying it has f ound a potential issue.
*3-Button Remotes If provided with your garage door opener , the large button is factory programmed to operate it. Additional buttons on any Security ✚ ® 3-Button remote or compact remote can be programmed to operate other Security ✚ ® garage door openers.
36 1. Press and release the “learn” button on motor unit. The learn indicator light will glow steadily for 30 seconds. 2. Within 30 seconds, enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold the ENTER button.
7 9 10 11 NOTICE 5 6 8 1 4 12 13 3 2 3 1 5 4 2 6 Installation Parts 37 REP AIR P ARTS Rail Assembly Parts KEY P ART NO . NO . DESCRIPTION 1 4A1008 Master link kit 2 41C5141-1 Complete trolley assembly 3 41A5665-2 Complete rail 4 144C56 Idler pulley 5 41A5807 Chain and cable 6 12D598-1 “U” bracket NO T SHO WN 183A163 Wear pads KEY P ART NO .
Motor Unit Assembly Parts 38 2 10 8 13 14 15 19 4 5 3 9 16 12 18 11 17 1 6 7 DN UP Brown Wire (Down) Contact LIMIT SWITCH ASSEMBLY Grey Wire Yellow Wire (Up) Contact Center Limit Contact Drive Gear KEY P ART NO . NO. DESCRIPTION 1 41A5615 Chain Spreader 2 41C4220A Gear and sprocket assembly .
39 ACCESSORIES LOCK LIGHT CLOSED OPEN LOCK LIGHT 3-Button SECURITY ✚ ® Remote Control: Includes visor clip. SECURITY ✚ ® Ke yless Entr y: Enables homeowner to operate garage door opener from outside by entering a password on a specially designed keyboard.
© 2008, The Chamberlain Group, Inc. 1 14A3642 All Rights Reserved CHAMBERLAIN SER VICE IS ON CALL OUR LARGE SER VICE ORGANIZA TION SP ANS AMERICA INST ALLA TION AND SERVICE INFORMA TION IS AS NEAR AS Y OUR TELEPHONE. SIMPL Y DIAL OUR T OLL FREE NUMBER: 1-800-528-9131 www .
Ein wichtiger Punkt beim Kauf des Geräts Chamberlain PD300DM (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Chamberlain PD300DM noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Chamberlain PD300DM - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Chamberlain PD300DM reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Chamberlain PD300DM erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Chamberlain PD300DM besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Chamberlain PD300DM verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Chamberlain PD300DM. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Chamberlain PD300DM gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
