Benutzeranleitung / Produktwartung 2565 1/2 HP des Produzenten Chamberlain
Zur Seite of 36
The Chamberlain Group, Inc. 845 Larch A venue Elmhurst, Illinois 60126-1 196 www .liftmaster .com GARAGE DOOR OPENER Model 2565 1/2 HP For Residential Use Only ® Owner’s Manual ■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation.
2 Introduction Pages 2-5 Safety symbol and signal word review ........................2 Preparing your garage door ........................................3 T ools needed ...............................................................3 Planning ......
3 T o prevent damage to garage door and opener: • AL W A YS disable locks before installing and operating the opener . • ONL Y operate garage door opener at 120V , 60 Hz to avoid malfunction and damage.
Safety Reversing Sensor Support bracket & fastening hardware is required. See page 13. — — — — — — — — Door Center Header Wall FINISHED CEILING Torsion Spring Extension Spring OR S.
5 Straight Door Arm Section Curved Door Arm Section Safety Labels and Literature Header Bracket U P CEILING MOUNT ONLY Sprocket Cover 2 Conductor Bell Wire White & White/Red Light Lens (2) Remote .
6 ASSEMBL Y STEP 1 Attach the T -Rail to the Motor Unit T o avoid installation difficulties, do not run the garage door opener until instructed to do so. • Remove the two washered bolts mounted in top of motor unit. • Position T -rail at a 45˚ angle to opener so one hole in T -rail and motor unit line up.
7 ASSEMBL Y STEP 3 Tighten the Chain • Spin the inner nut and lock washer down the threaded shaft, away from the trolley . • T o tighten the chain, turn outer nut in the direction shown.
8 INST ALLA TION STEP 1 Determine the Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door . SECTIONAL DOOR AND ONE-PIECE DOOR WITH TRACK 1. Close the door and mark the inside vertical centerline of the garage door .
9 Header Wall Vertical Centerline Vertical Centerline of Garage Door 2x4 Unfinished Ceiling 2x4 OPTIONAL CEILING MOUNT FOR HEADER BRACKET Structural Supports ONE-PIECE DOOR WITHOUT TRACK 1. Close the door and mark the inside vertical centerline of your garage door .
10 INST ALLA TION STEP 2 Install the Header Bracket Y ou can attach the header bracket either to the wall above the garage door , or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall.
Clevis Pin 5/16"x2-3/4" Ring Fastener 11 INST ALLA TION STEP 3 Attach the T -Rail to the Header Bracket • Position the opener on the garage floor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way you’ll need help.
12 ONE-PIECE DOOR WITHOUT TRACK • With the door fully open and parallel to the floor , measure the distance from the floor to the top of the door . • Using a stepladder as a support, raise the top of the opener to this height. • The top of the door should be level with the top of the motor unit.
13 INST ALLA TION STEP 5 Hang the Opener T wo representative installations are shown. Y ours may be different. Hanging brackets should be angled (Figure 1) to provide rigid support. On finished ceilings (Figure 2), attach a sturdy metal bracket to structural supports before installing the opener .
14 INST ALLA TION STEP 6 Install the Door Control Locate door control within sight of the door at a minimum height of 5 feet where small children cannot reach, and away from moving parts of the door and door hardware. The installation surface must be smooth and flat.
15 INST ALLA TION STEP 7 Install the Lights • Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens. • Install up to a 100 watt maximum light bulb in each socket.
16 INST ALLA TION STEP 9 Electrical Requirements T o avoid installation difficulties, do not run the opener at this time. T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet.
17 Invisible Light Beam Protection Area Sensor Beam 6" max. above floor Sensor Beam 6" max. above floor Facing the door from inside the garage INST ALLA TION STEP 10 Install The Protector System ® The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction.
18 FLOOR MOUNT (RIGHT SIDE) WALL MOUNT (RIGHT SIDE) DOOR TRACK MOUNT (RIGHT SIDE) Indicator light Lens Lip Sensor Bracket Door Track Sensor Bracket Extension Bracket (See Accessories) Lens Indicator l.
19 1/4"-20x1/2" Carriage bolt Lens Wing nut Figure 4 MOUNTING AND WIRING THE SAFETY SENSORS • Slide a 1/4"-20x1/2" carriage bolt head into the slot on each sensor . Use wing nuts to fasten sensors to brackets, with lenses pointing toward each other across the door .
20 INST ALLA TION STEP 11 Fasten the Door Bracket Follow instructions which apply to your door type as illustrated below or on the following page. A horizontal reinforcement brace should be long enough to be secured to two or three vertical supports. A vertical reinforcement brace should cover the height of the top panel.
21 Header Wall Vertical Centerline of Garage Door Finished Ceiling Optional Placement of Door Bracket Header Bracket Door Bracket 2x4 Support For a door with no exposed framing, or for the optional installation, use 5/16"x1-1/2" lag screws (Not provided) to fasten door bracket.
22 INST ALLA TION STEP 12 Connect Door Arm to T rolley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONL Y • Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley .
23 ALL ONE-PIECE DOORS 1. Assemble the door arm, Figure 4: • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). • With the door closed, connect the straight door arm section to the door bracket with the 5/16"x1-1/4" clevis pin.
24 ADJUSTMENT STEP 1 Adjust the UP and DOWN T ravel Limits Limit adjustment settings regulate the points at which the door will stop when moving up or down. T o operate the opener , press the Door Control push bar . Run the opener through a complete travel cycle.
ADJUSTMENT STEP 2 Adjust the Force Force adjustment controls are located on the right side panel of the motor unit. Force adjustment settings regulate the amount of power required to open and close the door . If the forces are set too light, door travel may be interrupted by nuisance reversals in the down direction and stops in the up direction.
Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSL Y INJURED or KILLED by a closing garage door . • Safety reversal system MUST be tested ever y month. • If one control (force or travel limits) is adjusted, the other control may also need adjustment.
OPERA TION 27 IMPORT ANT SAFETY INSTRUCTIONS 1. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS. 2. AL W A YS keep remote controls out of reach of children. NEVER permit children to operate or play with garage door control push buttons or remote controls.
28 Additional feature when used with the 3-function hand-held remote T o control the opener lights: In addition to operating the door , you may program the remote to operate the lights. 1. With the door closed, press and hold a small remote button that you want to control the light.
CARE OF YOUR OPENER LIMIT AND FORCE ADJUSTMENTS: Weather conditions may cause some minor changes in door operation requiring some re- adjustments, particularly during the first year of operation. Pages 24 and 25 refer to the limit and force adjustments.
30 Having a Problem? (Continued) 6. The garage door opens and closes by itself: • Be sure that all remote control push buttons are off. • Remove the bell wire from the door control terminals and operate from the remote only .
*3-Channel Remotes If provided with your garage door opener , the large button is factory programmed to operate it. Additional buttons on any Security ✚ 3-channel remote or mini-remote can be programmed to operate other Security ✚ garage door openers.
1. Enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold ENTER. 2. While holding the ENTER button, press and hold the LIGHT button on the Motion Detecting Door Control.
7 10 11 5 NOTICE U P CEILING MOUNT ONLY 8 6 1 4 3 2 9 12 LOCK LIGHT 1 3 4 5 6 2 Installation Parts 33 REP AIR P ARTS Rail Assembly Parts KEY P ART NO. NO.
Motor Unit Assembly Parts 34 DN UP Brown Wire (Down) Contact LIMIT SWITCH ASSY. Grey Wire Yellow Wire (Up) Contact Center Limit Contact Drive Gear 2 4 3 7 1 12 16 7 5 8 9 18 20 19 6 11 17 15 13 14 10 KEY P ART NO.
35 ACCESSORIES L O C K L IG H T 1708LM 97LM 1702LM 1710LM 976LM 974LM 970LM 982LM Plug-In Light Control: Enables homeowner to turn on a lamp, television or other appliance from car , bedside, or anywhere in the home with a remote. SECURITY ✚ 3-Channel Remote Control: Wood grain plastic case.
© 2002, The Chamberlain Group, Inc. 1 14A251 1C All Rights Reserved Printed in Mexico LIFTMASTER GARAGE DOOR OPENER FIVE-YEAR LIMITED W ARRANTY The Chamberlain Group, Inc.
Ein wichtiger Punkt beim Kauf des Geräts Chamberlain 2565 1/2 HP (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Chamberlain 2565 1/2 HP noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Chamberlain 2565 1/2 HP - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Chamberlain 2565 1/2 HP reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Chamberlain 2565 1/2 HP erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Chamberlain 2565 1/2 HP besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Chamberlain 2565 1/2 HP verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Chamberlain 2565 1/2 HP. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Chamberlain 2565 1/2 HP gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
