Benutzeranleitung / Produktwartung 2000SD des Produzenten Chamberlain
Zur Seite of 36
TM The Chamberlain Group, Inc. A DUCHOSSOIS ENTERPRISE 845 Larch Avenue Elmhurst, Illinois 60126-1196 For Residential Use Only Garage Door Opener Owner’ s Manual Model 2000SD 1/2 HP Model 1000SD 1/3.
Start by re viewing these important safety alert symbols: 2 Safety alert symbol re view ............................................2 Safety information and precautions ..............................3 T esting your garage door for binding & balance .
3 An unbalanced garage door might not rever se when required and someone under the door could be seriously injured or killed. If your garage door binds, sticks or is out of balance, call for prof essional garage door ser vice.
4 Straight Door Arm Section Curved Door Arm Section Rail Brackets Header Bracket U P C E IL IN G M O U N T O N L Y Safety Reversing Sensor Mounting Bracket With Square Holes (2) "C" Wrap (2).
Y ou may f ind it helpful to refer back to this page as y ou pr oceed with the installation of y our opener . Safety Reversing Sensor Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.
ASSEMBL Y STEP 1 Fasten the Rail T o the P ower Unit 6 Rail Sprocket Rail Assembly Trolley Coupling Rail/Power Unit Bracket Lock Nuts 1/4"-20 Power Unit Sprocket Opener Chassis Foam Packaging Hex.
ASSEMBL Y STEP 3 Attach the Rail Brac kets 7 IMPOR T ANT INST ALLA TION INSTR UCTIONS T o reduce the risk of se ver e injury or death to persons: 1. READ AND FOLLO W ALL INST ALLA TION INSTR UCTIONS 2. Install only on a properly balanced and lubricated garage door .
• Open your door to the highest point of trav el as shown. Dra w an inter- secting horizontal line on the header wall 3" abo ve the high point. This height will provide tra vel clearance for the top edge of the door .
Header Wall Vertical Centerline Vertical Centerline of Garage Door 2x4 Unfinished Ceiling Structural Supports 2x4 Header Support OPTIONAL CEILING MOUNT FOR HEADER BRACKET • Close the door and mark the inside vertical centerline of your garage door .
Lag Screws 5/16"x9x1-5/8" Highest Point of Travel (of Garage Door) Vertical Center Line Header Wall Garage Door UP CEILING MOUNT ONLY Wall Mounting Holes Optional Wall Mounting Holes The nail hole is for positioning only. You must use lag screws to mount the header bracket.
Adjustment Step 4 T est the Safety Rever se System T est • Place a one-inch board (or a 2x4 laid flat) on the floor , centered under the garage door .
The safety re versing sensor must be connected and aligned correctly bef ore the garage door opener will move in the do wn direction. This is a requir ed safety device and cannot be disabled. Installation pr ocedur es ar e the same for sectional and one-piece doors.
Adjustment Step 1 Adjust the UP and DO WN Limits Do not make any limit adjustments until the safety re versing sensors are completely installed. 24 Limit adjustment settings regulate the points at which the door will stop when moving up or do wn. The door will stop in the up direction if anything interferes with door trav el.
Door Arm Fully Open Trolley Closed Door Open Door Door with Backward Slant Door Arm Connector Hole Door Arm Connector Hole Fully Closed Trolley Door Arm Nuts 5/16"-18 Lock Washers 5/16" Ring.
Installation Step 13 Connect Door Arm to T rolley F ollow instructions which apply to your door type as illustrated below and on page 23. Make sur e garage door is fully closed. Pull the emergency release handle to disconnect the outer tr olley from the inner trolley .
Installation Step 6 Hang the Opener T wo repr esentative installations ar e shown. Y ours may be different. Hanging brack ets should be angled, Figure 1, to provide rigid support. On f inished ceilings, Figure 2, attach a sturdy metal bracket to structural supports before installing the opener .
In stallation Step 12 Fasten Door Brac ket F ollow instructions which apply to your door type as illustrated below or on page 21. T o pre vent damage to steel, aluminum, fiberglass or glass panel doors, always reinf orce the inside of the door both vertically and horizontally with an angle ir on.
T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you ha ve, contact a qualified electrician to install the proper outlet.
T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you ha ve, contact a qualified electrician to install the proper outlet.
In stallation Step 12 Fasten Door Brac ket F ollow instructions which apply to your door type as illustrated below or on page 21. T o pre vent damage to steel, aluminum, fiberglass or glass panel doors, always reinf orce the inside of the door both vertically and horizontally with an angle ir on.
Installation Step 6 Hang the Opener T wo repr esentative installations ar e shown. Y ours may be different. Hanging brack ets should be angled, Figure 1, to provide rigid support. On f inished ceilings, Figure 2, attach a sturdy metal bracket to structural supports before installing the opener .
Installation Step 13 Connect Door Arm to T rolley F ollow instructions which apply to your door type as illustrated below and on page 23. Make sur e garage door is fully closed. Pull the emergency release handle to disconnect the outer tr olley from the inner trolley .
Door Arm Fully Open Trolley Closed Door Open Door Door with Backward Slant Door Arm Connector Hole Door Arm Connector Hole Fully Closed Trolley Door Arm Nuts 5/16"-18 Lock Washers 5/16" Ring.
Adjustment Step 1 Adjust the UP and DO WN Limits Do not make any limit adjustments until the safety re versing sensors are completely installed. 24 Limit adjustment settings regulate the points at which the door will stop when moving up or do wn. The door will stop in the up direction if anything interferes with door trav el.
Adjustment Step 2 Adjust the Force Too much force on the door will interfere with the proper operation of the safety reverse system. The door might not reverse properly when required and could seriously injure or kill someone under it. Do not increase the force beyond the minimum amount required to close the door.
Adjustment Step 4 T est the Safety Rever se System T est • Place a one-inch board (or a 2x4 laid flat) on the floor , centered under the garage door .
Lag Screws 5/16"x9x1-5/8" Highest Point of Travel (of Garage Door) Vertical Center Line Header Wall Garage Door UP CEILING MOUNT ONLY Wall Mounting Holes Optional Wall Mounting Holes The nail hole is for positioning only. You must use lag screws to mount the header bracket.
Header Wall Vertical Centerline Vertical Centerline of Garage Door 2x4 Unfinished Ceiling Structural Supports 2x4 Header Support OPTIONAL CEILING MOUNT FOR HEADER BRACKET • Close the door and mark the inside vertical centerline of your garage door .
Children operating or playing with a garage door opener can injure themselves or others. The garage door could close and cause serious injury or death. Do not allow children to operate the door control(s) or remote control transmitter(s). A moving garage door could injure or kill someone under it.
ASSEMBL Y STEP 3 Attach the Rail Brac kets 7 IMPOR T ANT INST ALLA TION INSTR UCTIONS T o reduce the risk of se ver e injury or death to persons: 1. READ AND FOLLO W ALL INST ALLA TION INSTR UCTIONS 2. Install only on a properly balanced and lubricated garage door .
ASSEMBL Y STEP 1 Fasten the Rail T o the P ower Unit 6 Rail Sprocket Rail Assembly Trolley Coupling Rail/Power Unit Bracket Lock Nuts 1/4"-20 Power Unit Sprocket Opener Chassis Foam Packaging Hex.
Y ou may f ind it helpful to refer back to this page as y ou pr oceed with the installation of y our opener . Safety Reversing Sensor Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.
4 Straight Door Arm Section Curved Door Arm Section Rail Brackets Header Bracket U P C E IL IN G M O U N T O N L Y Safety Reversing Sensor Mounting Bracket With Square Holes (2) "C" Wrap (2).
3 An unbalanced garage door might not rever se when required and someone under the door could be seriously injured or killed. If your garage door binds, sticks or is out of balance, call for prof essional garage door ser vice.
Index Access Door/Outside Quick Release Accessory .........................................................................................................31, 34 Electrical Safety W arnings .............................................................
TM The Chamberlain Group, Inc. A DUCHOSSOIS ENTERPRISE 845 Larch Avenue Elmhurst, Illinois 60126-1196 For Residential Use Only Garage Door Opener Owner’ s Manual Model 2000SD 1/2 HP Model 1000SD 1/3.
Ein wichtiger Punkt beim Kauf des Geräts Chamberlain 2000SD (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Chamberlain 2000SD noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Chamberlain 2000SD - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Chamberlain 2000SD reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Chamberlain 2000SD erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Chamberlain 2000SD besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Chamberlain 2000SD verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Chamberlain 2000SD. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Chamberlain 2000SD gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
