Benutzeranleitung / Produktwartung 120ad des Produzenten Chamberlain
Zur Seite of 32
QLD Office: 17 Oasis Court Clontarf 4019 (07) 3883-0200 NSW Office: 34-36 Marigold Street Revesby 2212 (02) 9722 5555 VIC/T AS Office: 147-153 Canterbury Road Kilsyth 3137 (03) 9237 7766 B&D Doors New Zealand: 70 Allens Road EastT amaki Auckland, New Zealand (09) 273 8600 www .
2 Introduction 2-7 Safety rule review ........................................................2 Preparing your garage door ........................................3 T ools needed ...............................................................3 Planning .
3 Pliers Wire Cutters Claw Hammer Hack Saw Screwdriver Adjustable End Wrench Locking pliers 13mm, 11mm, and 6mm Sockets and Wrench Drill Tape Measure 2 1 Stepladder Pencil 8mm, 5mm, and 4mm Drill Bits Carpenter's Level T o avoid damage to the garage door and opener , disable locks before installing and operating the opener .
Safety Reversing Sensor Horizontal and vertical reinforcement is needed for lightweight garage doors (fibreglass, steel, aluminum, door with glass panels, etc.). See page 21 for details. Support bracket & fastening hardware is required. See page 17.
5 Access Door Gap between floor and bottom of door must not exceed 6mm. Safety Reversing Sensor The Chamberlain Group, Inc. One-Piece Door with T rack Installation (Cable -USA) 3/3/93 Header Bracket H.
6 Y our garage door opener is packaged in two cartons which contains the motor unit and the parts illustrated below . If anything is missing, carefully check the packing material. Parts may be stuck in the foam. Hardware for assembly and installation is shown on the next page.
Hardwar e Inventory Separate all hardware and group as shown below for the assembly and installation procedures. 7 Spri ng /Tro lley Nut (1 ) Mast er Link (2) ASSE MBLY INSTALLATION NOT ICE Handle Rop.
8 ASSEMBL Y STEP 1 Assemble the Rail NOTE: If your opener came with a one piece rail, proceed to Assembly step 2, page 9. Grease inside edges of rail brace sections. Place rail pieces on flat surface for assembly . All four rail sections are interchangeable.
9 ASSEMBL Y STEP 3 Attach Chain Spreader Attach chain spreader to opener with phillips pan head screws. Chain Spreader P hillips Pan Head Screws Opener T o avoid serious damage to opener , ONL Y use screws mounted in top of motor unit.
Bolt Tr olley Stop Bolt Hole L ock Was her Nut Bolt Nut Lock Washer Was h ere d Bolt Spr o ck e t 2 S top s 4 Spr o ck e t Spre a d er Stops Spreader Screwdriver T ip Nut Ring Wre nch Spring Nut Header Sleeve Screwdriver T ip Nut Ring Wre nch Spring Nut Header Sleeve F ASTEN RAIL TO OPENER SET CHAIN TENSION 10 1 14A2845 114mm 114mm 1.
11 IMPORT ANT INST ALLA TION INSTRUCTIONS 1. READ AND FOLLOW ALL INST ALLA TION WARNINGS AND INSTRUCTIONS. 2. Install garage door opener only on properly balanced and lubricated garage door . An improperly balanced door may not reverse when required and could result in severe injury or death.
12 INST ALLA TION STEP 1 Determine the Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door . SECTIONAL DOOR AND ONE-PIECE DOOR WITH TRACK 1. Close the door and mark the inside vertical centreline of the garage door .
13 One Piece Door Without T rack 1/30/92 - 4/7/92 Header Wa l l Ve r tical Centreline Ve r tical Centreline of Garage Door 40mm Reinforcement Board Unfinished Ceiling OPTIONAL CEILING MOUNT FOR HEADER BRACKET Structural Supports 40mm Reinforcement Board ONE-PIECE DOOR WITHOUT TRACK 1.
14 INST ALLA TION STEP 2 Install the Header Bracket W ALL HEADER BRACKET INST ALLA TION • Centre the bracket on the vertical guideline with the bottom edge of the bracket on the horizontal line (with the arrow pointing toward the ceiling). • Mark all of the bracket holes.
15 Ring fastener (2) Temporary Support Garage Door Header Wall Header Bracket Header Sleeve Bracket Clevis PIn 8mm x 13mm (2) Ring Fastener Ring Fastener Clevis Pin 8mm x 13mm Clevis Pin 8mm x 13mm He.
16 T op of Motor Unit Header Bracket Top of door Door ONE-PIECE DOOR WITHOUT TRACK • With the door fully open and parallel to the floor , measure the distance from the floor to the top of the door . • Using a stepladder as a support, raise the top of the opener to this height.
17 1 14A2845 INST ALLA TION STEP 6 Install the door control Locate the door control within sight of the door at a minimum height of 1.5m where small children cannot reach, and away from all moving parts of the door and door hardware. 1. Strip 6mm of insulation from one end of the bell wire.
18 WIRING INSTRUCTIONS FOR ACCESSORIES • Place entrapment warning label on the inside of door as a reminder of safe operating procedures. Place the manual release/safety reverse test label in plain view on the inside of the garage door .
19 1 14A2845 Overhand Knot Em ergency R elease Handle T rolley Release Arm NOTICE The Chamberlain Group, Inc. Figure 16 - Manual Release 4210E - 3/8/93 Rope T rolley • T o prevent possible SERIOUS INJURY or DEA TH from a falling garage door: – If possible, use emergency release handle to disengage trolley ONL Y when garage door is CLOSED.
20 Invisible Light Beam Protection Area The Chamberlain Group, Inc. Safety Sensor Instruction Sheet Page 1 Protector System Disk #1 (Yellow) 11/5/91 - 1/15/92 Wing Nut Sensor Beam 100-150mm max. above floor Sensor Beam 100-150mm max.
21 Carriage Bolt 8mm x 65mm Nut 8mm Lock Washer 8mm Sheet Metal Screw HARDW ARE SHOWN ACTUAL SIZE 1 14A2845 Fibreglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket. T o prevent damage to garage doors reinforce inside of door with angle iron both vertically and horizontally .
22 Carriage Bolt 8mm x 65mm Nut 8mm Lock Washer 8mm Sheet Metal Screw HARDW ARE SHOWN ACTUAL SIZE 1 14A2845 Header W all Ve r tical Centreline of Garage Door Finished Ceiling Optional Placement of Doo.
23 INST ALLA TION STEP 12 Connect Door Arm to T rolley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONL Y • Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley .
ALL ONE-PIECE DOORS Assemble the Door Arm: • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). • With the door closed, connect the straight door arm section to the door bracket with the 8mm x 32mm clevis pin.
25 ADJUSTMENT STEP 1 Limit Adjustment Run the opener through a complete travel cycle. Force adjustments are not necessary when the door opens and closes completely and doesn't reverse unintentionally in the fully closed position. Locate the button on the back panel of motor unit.
ADJUSTMENT STEP 2 Adjust the Force The force, as measured on the closing edge of the door , should not exceed 400N (40kg). If the closing force is measured to more than 400N, a Safety Infrared Reversing Sensor must be installed See step 3 on page 27. The force setting button is located on the back panel of the motor unit.
ADJUSTMENT STEP 3 T est the Safety Reverse System TEST • With the door fully open, place a 40mm board on the floor , centered under the garage door . • Operate the door in the down direction. The door must reverse on striking the obstruction. ADJUST • If the door stops on the obstruction, it is not traveling far enough in the down direction.
28 Using Y our Garage Door Opener Y our opener will operate with up to twelve remote control transmitters, one entry keypad, and one dip- switch code transmitter . If you purchase a new remote, or if you wish to deactivate any remote, follow the instructions in the Programming section.
29 T o Open the Door Manually DISCONNECT THE TROLLEY : The door should be fully closed if possible. Pull down on the emergency release handle (so that the trolley release arm snaps into a vertical position) and lift the door manually .
T roubleshooting 1. Opener doesn't operate from either door control or remote: • Does the opener have electric power? Plug lamp into outlet. If it doesn't light, check the fuse box or the circuit breaker . (Some outlets are controlled by a wall switch.
31 T o Erase All Codes From Opener Receiver Memory T o deactivate any unwanted remote, first erase all codes: Press and hold the “Learn” button on opener until the smart indicator light goes out (approximately 6 seconds). All previous codes are now erased.
1 14A2845 ©2005, All Rights Reserved Printed in Mexico W ARRANTY Controll-A-Door ® Automatic Garage Door Opener 1. Definitions ‘B&D’ means (a) in Australia - B&D Doors of 17 Oasis Court Clontarf, Queensland 4019 (b) in New Zealand - B&D Doors (NZ) Ltd of 70 Allens Road East T amaki Auckland, which is a subsidiary of Alesco NZ Ltd.
Ein wichtiger Punkt beim Kauf des Geräts Chamberlain 120ad (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Chamberlain 120ad noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Chamberlain 120ad - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Chamberlain 120ad reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Chamberlain 120ad erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Chamberlain 120ad besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Chamberlain 120ad verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Chamberlain 120ad. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Chamberlain 120ad gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
