Benutzeranleitung / Produktwartung FW552 des Produzenten CDA
Zur Seite of 20
Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .
Important The CD A Group L td cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CD A reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance.
This appliance has been manufactured to the strictest standards and complies with all applicable legislation, including Electrical safety (L VD) and Electromagnetic interference compatibility (EMC). Parts intended to come into contact with food conform to EEC/89/109 .
Important Never store inflammable or explosive items and strong corrosive acids or alkalis in the appliance. This is a household appliance, which is produced in accordance with the national standard. It is intended for food storage only, not for storage of blood, medicine and biological products.
Before First Use You must allow the fridge to settle for at least twenty four hours prior to switching the power on. It is recommended that you clean the interior of the appliance prior to first use, using a solution of bicarbonate of soda and warm water and then thoroughly drying the interior.
fig. 1 Setting the T emperature You must allow the fridge to settle for at least twenty four hours prior to switching the power on. To adjust the temperature turn the thermostat control knob clockwise (from o) to the required level. The temperature becomes colder the higher the number on the control.
• Make sure food is clean and any extra water is wiped away before putting into the fridge. • Wrap or cover food before putting into the fridge. This will help prevent the loss of moisture, keep food fresh and avoid unpleasant odours. • Sort foods prior to storing.
• Avoid contact between already frozen food and food that has yet to be frozen (approx. 20 mm distance). • After 24 hours turn the thermostat knob back to the normal position. Please note: the amount of fresh food that can be frozen within 24 hours is shown on the rating plate as freezing capacity.
Care and cleaning Always disconnect the appliance from the power supply before any cleaning or maintenance. The fridge sections should be cleaned using a solution of bicarbonate of soda and lukewarm water. Do not use abrasive products or detergents. After washing, rinse and dry thoroughly.
fig. 2 Defrosting the Fridge The fridge is self-defrosting. Any water created will run out of the fridge through the channel at the back of the fridge. It is important to keep the channel clear at all times. The defrosted water is collected in the evaporating tray at the back of the appliance.
Changing the Light Bulb Disconnect the appliance from the power. • Carefully remove the light cover by pushing in the lever at the back of the cover, and then pulling the cover down. • Unscrew the light bulb to remove it and replace with a new bulb (15W max).
• The cooling system at the rear of the appliance is clean and free of dust, and not touching the rear wall. • There is enough ventilation at the side and rear walls. • The temperature of the room is adequate (10 o C or above). The appliance is noisy • The appliance is level and stable.
fig. 2 Installation Product Dimensions and aperture required for installation: Y our refrigerator is designed to be installed into a standard larder unit of width 560-570mm and depth of 550mm. the diagram below shows the product dimensions and aperture required.
2 1 B-C fig. 5 Fig. 3 - Fitting the decor door bracket Unscrew and remove the nuts and washers from the appliance door . Place fixing bracket on the appliance door by inserting the holes to adjustment bolts. Dimension B= Measure from the underside surface of kitchen unit to the bottom of fixing bracket.
fig. 8 Fig. 6 - Aligning the decor door Close the door and check the alignment with the other unit doors. Adjust the decor door by screwing or unscrewing the adjustment bolts for vertical adjustment and by the help of the slots on the fixing bracket for other directions.
Fig.9 - Fitting the plinth Fit the plinth section, providing minimum 25 mm gap between the cabinet door and fix it. Never cover over the ventilation slots. Once installed the plinth must not block the ventilation slots in the appliance. This may require cutting the plinth down.
Reversing the Door It is possible to reverse the door on this appliance, if required. To do so, follow the steps below: 1. Open the door. 2. Remove the white hinge screw cover plate carefully to gain access to the hinge screws. 3. Loosen the hinge fixing screws (1) and remove the door.
Electrical information W arning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13Amp fused plug. T o change a fuse in this type of plug, follow the steps below: 1. R emove the fuse cover and fuse. 2.
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: • The wire which is coloured GREEN and YELL O W must be connected to the terminal which is marked with letter (E) or by the Earth symbol or coloured GREEN and YELL O W .
Please contact our Customer Care Department, or for Service on the details below . Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .
Ein wichtiger Punkt beim Kauf des Geräts CDA FW552 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie CDA FW552 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für CDA FW552 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von CDA FW552 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über CDA FW552 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon CDA FW552 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von CDA FW552 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit CDA FW552. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei CDA FW552 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
