Benutzeranleitung / Produktwartung FW321 des Produzenten CDA
Zur Seite of 20
Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .
2 Important The CD A Group L td cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CD A reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance.
3 CE Declarations of Conformity: This appliance has been designed, constructed and marketed in compliance with safety requirements of EEC Directive 2006/95/EEC (L ow voltage) and requirements of EMC Directive 2004/108/EEC.
4 Important Never store inflammable or explosive items and strong corrosive acids or alkalis in the appliance. This is a household appliance, which is produced in accordance with the national standard. It is intended for food storage only , not for storage of blood, medicine and biological products.
5 Before First Use Y ou must allow the fridge to settle for at least twenty four hours prior to switching the power on. It is recommended that you clean the interior of the appliance prior to first use, using a solution of bicarbonate of soda and warm water and then thoroughly drying the interior .
6 Setting the T emperature Y ou must allow the fridge to settle for at least twenty four hours prior to switching the power on. T o adjust the temperature turn the thermostat control knob clockwise (from o ) to the required level. The temperature becomes colder the higher the number on the control.
7 Use Fridge • Never put liquids in the refrigerator uncovered. • Never put hot foods in the refrigerator . W arm food should be allowed to cool to room temperature before being put into the refrigerator .
8 Care and Cleaning Always disconnect the appliance from the power supply before any cleaning or maintenance. The fridge sections should be cleaned using a solution of bicarbonate of soda and lukewarm water . Do not use abrasive products or detergents.
9 Defrosting the Fridge The fridge is self-defrosting. Any water created will run out of the fridge through the channel at the back of the fridge. It is important to keep the channel clear at all times. The defrosted water is collected in the evaporating tray at the back of the appliance.
10 T roubleshooting If you have any problems with your appliance, you should check the troubleshooting prior to calling CD A Customer Care to prevent unnecessary service calls and potential cost. The appliance is not working • Check there is power to the appliance: • The house fuses are intact and the fuse in the plug has not blown.
11 There is water in the lower part of the refrigerator compartment • The drain hole in the channel at the back of the compartment is clear . Installation This appliance must never be installed close to heat sources i.e. heating elements, radiators, cookers or in damp places.
12 Fig. 4 - Dimensions of the appliance Fig. 5 - Fitting the worktop bracket R emove the screw (5) on the top of the appliance, locate the top bracket(6) and fix the bracket with screw(5). Fig. 6 - Fitting the spacer piece T ake out the spacer piece (11) located on the side panel and remove the protective tape.
13 Fig. 7 - Adjusting the appliance height The height of the appliance can be adjusted by the help of adjustable feet to fit the furniture height. Use a spirit level to ensure the appliance is level. Fig. 8 - Aligning the appliance Slide the appliance into the kitchen unit and align the hinge surface with front surface of the kitchen unit.
14 Fig. 10 - Fitting the decor door bracket Unscrew and remove the nuts and washers from the appliance door . Place fixing bracket on the appliance door by inserting the holes to adjustment bolts. Dimension B= Measure from the underside surface of kitchen unit to the bottom of fixing bracket.
15 Fig. 12 - Fitting the decor door Place the decor door onto the appliance door by inserting adjustment bolts into the slots on the fixing bracket. L ocate the washers and screw the nuts onto the adjustment bolts. Fig. 13 - Aligning the decor door Close the door and check the alignment with the other unit doors.
16 Fig. 15 - Fitting the decorative cover Fit the decorative cover (4) on the decor door fixing bracket. Fig. 16 - Fitting the plinth Fit the plinth section, providing minimum 25 mm gap between the cabinet door and fix it. Never cover over the ventilation slots.
17 R eversing the door It is possible to reverse the door on this appliance, if required. T o do so, follow the steps below: 1. Open the door . 2. Loosen the hinge fixing screws (1) and remove the door . 3. R emove the door fixing screws (2). 4. R emove the cover caps (3).
18 Electrical Information W arning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. T o change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse .
19 As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:- • The wire which is coloured GREEN and YELLO W must be connected to the terminal which is marked with letter (E) or by the Earth symbol or coloured GREEN and YELL O W .
Please contact our Customer Care Department for Service on the details below Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.
Ein wichtiger Punkt beim Kauf des Geräts CDA FW321 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie CDA FW321 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für CDA FW321 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von CDA FW321 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über CDA FW321 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon CDA FW321 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von CDA FW321 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit CDA FW321. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei CDA FW321 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
