Benutzeranleitung / Produktwartung MSR/Adit 3K GUI des Produzenten Carrier Access
Zur Seite of 262
Adit 3000 Series and Multi-Service Router (MSR) Card GUI R EFERENCE M ANUAL Part Number : 770-0169 BB Product Release: Adit 3000 Series - 1.6 MSR Card - 2.
Copyright 2008 Turin Netw orks Inc. All rights reserv ed. The information presented in this manual is subj ect to change without notice and does not represent a commitment on the part of Tu rin Networ ks Inc. The h ardware and software des c ribed herein are furnished under a license or non-disclo sure agreement.
P REFACE Preface Safety Information CAUTION! W HEN USING YOUR TELEPHONE EQUIPMENT , BASIC SAFE TY PRECAUTION S SHOULD ALWAYS BE FOL LOWED TO REDU CE THE RI SK OF FIRE , EL ECTRIC SHOCK AND INJ URY TO .
iv Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Preface Notices This manual contains impo rtant information and warnings that must be followed to ensure safe operation of the equipment. DANGER! A D ANGER NOTICE INDICATES THE PRESENCE OF A HAZARD THAT CAN OR WILL CAUSE DEATH OR SEVE RE PERSONAL INJURY IF THE HAZARD IS NOT AVOIDED .
T ABLE OF C ONTENTS Preface Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
vi Adit 3000 (Rel. 1.6) a nd MSR Card (Rel 2.0) GU I Table of Contents DNS Static Entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18 Viewing the DNS Table . . . . . . . . .
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI vii Table of Contents 3 Network Connections Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Adit 3000 Connections .
viii Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Table of Contents Firewall Implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-37 Network Connection Confi guration . . . .
C HAPTER 1 Web Based Management This Reference Manual covers the web-based Gr aphical User Interface (GUI) for the following products: Adit 3000 series (Adit 31 04, Adit 3200, and Adit 3500) M.
1-2 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Web Based Management Overview of Supported Products Overview of Supported Products The following products have different hardware co nfigurations, a.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 1-3 Web Based Management Accessing the GUI Accessing the GUI NOTE: The following instructions assume that you have connected your PC to the Ethernet port on the Adit 3000 (3104, 3200, or 3500) or MSR card.
1-4 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Web Based Management Overview Overview The GUI management window contains two sections: Navigation Pane (on the left) – Provides a list of topics to view and config ure. When you select an icon, the information is displayed on the right.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 1-5 Web Based Management Overview Navigation Pane Icons The following icons are availa ble on the Navigatio n Pane: Action Icons (for Managing Lists) The following icons may ap pear in a list, under Ac tion : Home - Displays the Network Map.
1-6 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Web Based Management Home Home The Home window displays the Network Map wh ic h shows the various elements in the network.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 1-7 Web Based Management Home Network Map The following icons appear on the Network Map. For all icons except the Internet, you can open the item’s configuration window by clicking on the icon. Symbol Represents Internet.
1-8 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Web Based Management Home Host Information Window To display this window, click on the Co mputer Host icon on the Network Map. The Host Information window d isplays ne twork information for the corresponding computer.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 1-9 Web Based Management Home Test Connectivity The Test Connectivity button brin gs up the Diagnostic s window. This window will automatically ping the Host IP Address and display the results. NOTE: This window can also be access ed thr ough Advanced/Diagnostics.
1-10 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Web Based Management Quick Setup Quick Setup The Quick Setu p window enables quick configuration of your Internet connection. When subscribing to a broadband service, you should be aware of the method by which you are connecting to the Internet.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 1-11 Web Based Management Quick Setup Internet Connection Connection Type The WAN conn ection can be configured using any of the following methods. With each of these connection types, the window disp lays a different set of field options.
1-12 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Web Based Management Quick Setup Manual IP Address Ethernet Connection This window is used to manually configure the Internet Connection with a specific IP Address. Field Definition IP Address Enter the IP Address for the Ethe rnet connection of this device.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 1-13 Web Based Management Quick Setup Automatic IP Address Ethernet Connecti on With this selection, the device uses DHCP to find and set an address for this connection.
1-14 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Web Based Management Quick Setup Point-to-Point Protocol over DS0 (Serial) With this selection, the MSR card uses a single Link Cross-Connect (LCC) PPP WAN for Internet connectivity.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 1-15 Web Based Management Quick Setup.
1-16 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Web Based Management Quick Setup Multilink Point-to-Point Protocol over DS0 (Multilink) With this selection, the MSR card uses a multip le Link Cross-Connect (LCC) WAN for Internet connectivity.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 1-17 Web Based Management Quick Setup.
1-18 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Web Based Management Quick Setup Point-to-Point Tunneling Protocol (PPTP) Point-to-Point T unneling is a technology for cr eating V irtual Private Networks (VPNs). A VPN is a private network of computers th at uses the pub lic Internet to connect some nodes.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 1-19 Web Based Management Quick Setup No Internet Connection This option disables the Intern et connection on the device. Administrator The following section appears on all Quick Setup windows (located at the bottom of the wi ndow) .
1-20 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Web Based Management Network Connections Network Connections Main Window The Network Connection window allows the user to create and configure netw or k connections. For the Adit 3000, the basic connections for this system ar e preconfigured.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 1-21 Web Based Management Network Connections Adit MSR.
1-22 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Web Based Management Security Security The Adit 3000 and MSR include c omprehe nsive and robust security services: Stateful Packet Inspection F.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 1-23 Web Based Management Voice over IP Voice over IP The VoIP feature allows you to connect multiple phones over a singl e broadband connection, providing the benefits and quality of digital voice.
1-24 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Web Based Management Voice over IP.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 1-25 Web Based Management Advanced Advanced This section of the Management Console is intended primarily for more advanced users. Some changes to settings within this section c ould adversely affect the operation of the Adit and the network, and should be made with caution.
1-26 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Web Based Management System Monitoring System Monitoring The System Monitoring window d isplays important sy stem information that can be used to monitor and troubleshoot the system. Connection status, alarms , system information, and logs are all accessible through this window.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 1-27 Web Based Management System Monitoring Adit MSR.
1-28 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Web Based Management Logout Logout The Logout feature logs the us er out of the system and returns to the Login win dow.
C HAPTER 2 Advanced In this Chapter Overview ARP Certificates Date and Time Diagnostics DNS Static Entries Dynamic DNS IP Address Distribution (DHCP) IPSec (IP Secu.
2-2 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Overview Overview This section of the Management Co nsole is intended primarily for mo re advanced users. Some changes to settings within this section coul d adversely affect the operation of the system and the network, and should be made with caution.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-3 Advanced ARP ARP The ARP (Address Resolution Protocol) win dow displays the current ARP table. There are display options: eth-1 - When checked, displays the LAN Ethernet ARP. eth-2 - When checked, displays the WAN Ethernet ARP.
2-4 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Certificates Certificates Public-key cryptography uses a pair of keys: Public Key, which encrypts data (known to the world) A corre.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-5 Advanced Certificates X.509 Certificate Format The Adit 3000 and Adit MSR supp ort X.509 cer tificates that comply with the ITU-T X.
2-6 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Certificates Obtaining and Loading an X.509 Certificate To obtain an X509 certificate, yo u must ask a CA to issue you one. You provide your public key, proof that you possess the corresponding pr ivate key, and some specific info rmation about yourself.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-7 Advanced Certificates 2. On the Adit 30 00 or Adit MSR’s Local tab, select the Create Certificate Request button. 3. Fill in your current information and select the Generate button. Note: It may take a minute or so to get the certif icate, and you may need to refresh the window.
2-8 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Certificates 4. Copy and store the exact contents of the certificate to a file, and send it to a CA for signing.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-9 Advanced Certificates 5. Select the Close button. The Certificates window appears, listing the certificate as Unsigned . 6. After receiving the signed certificate from the CA, select Load Certificate .
2-10 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Certificates 7. Paste the signed certificate. 8. Select the Load button. The Certificates window appear s, displaying the name and issuer of the certificate.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-11 Advanced Certificates Registering the CA’s Certificate After receiving the signed certificate from the CA: 1.
2-12 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Certificates 2. Select Load Certificate , and paste the CA’s certificate into the window. 3. Select the Load button to register the signed Certificat e. The Certificates window appears , displaying the name and issuer of the certificate.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-13 Advanced Date and Time Date and Time This window allows the user to configure the date and time parameters for the unit. NOTE: By default, Time of Day management for the MSR is provided by the Adit 600 controller.
2-14 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Date and Time Setting the Date and Time 1. Select Advanced/ Date and Time . 2. Set the Time Zone of this unit from the Time Zone pulldown me nu. 3. Set Daylight Saving Time as necessary: 4.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-15 Advanced Date and Time Field Definition Enabled Check box to enable the Automatic Time Update. Protocol Select the protoco l to be used to perform the time update. Time of Day - Retri eves the time from the TOD server (defined i n the Time Server field below).
2-16 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Diagnostics Diagnostics The Diagnostics window allows the user to test network connectivity usin g the following methods: Ping an IP a.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-17 Advanced Diagnostics Pinging an IP Address 1. Select Advanced/ Diagnostics . 2. Enter the IP address in the Ping/Destination field. 3. Select the Go button. The results of the Ping will be displayed.
2-18 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced DNS Static Entries DNS Static Entries The Domain Naming System (DNS) pr ovides a service that translates domain names into IP addresses and vice versa.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-19 Advanced DNS Static Entries Adding a New Entry to th e DNS Table 1. Select Advanced/ DNS Static Entr ies . 2. Select New DNS Entry . 3. Enter the computer’s Host Name and IP Address . 4. Select OK .
2-20 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced DNS Static Entries Modifying an Entry in the DNS Table 1. Select Advanced/ DNS Static Entr ies . 2. Select an entry on the list to modify. 3. The DNS Entry window appears. Mo dify the Host Name and IP Address , as needed.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-21 Advanced Dynamic DNS Dynamic DNS The Dynamic DNS service allows you to alias a dynamic IP address to a static host name, allowing your computer to be more easily accessible from variou s locations on the Intern et.
2-22 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Dynamic DNS Using Dynamic DNS 1. Select Advanced/ Dynamic DNS . 2. Specify the Dynamic DNS operating parameters: 3. Select Apply or OK to save the configuration. Field Definition Connection to Update Select the connection to be used for the update from the pulldow n menu.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-23 Advanced IP Address Distribution (DHCP) IP Address Distribution (DHCP) The Adit’s DHCP server makes it pos s ible to easily add computers that are configured as DHCP clients to the network.
2-24 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced IP Address Distribution (DHCP) Editing DHCP Server Settings To edit the DHCP server setting for a device: 1. Select Advanced/ IP Address Distribution . 2. Select the interface to configure (Ethernet 1/Ethernet 2).
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-25 Advanced IP Address Distribution (DHCP) Provide Host Name if Not Specified by Client If the DHCP client does not have a h ost name, the Adit will assign the client a default name. DHCP Relay New IP Address Opens a new window for entering an IP address.
2-26 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced IP Address Distribution (DHCP) Defining a New Connection with a Fixed IP Address 1. Select Advanced/ IP Address Distribution .
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-27 Advanced IP Address Distribution (DHCP) 3. Select New Static Connection . 4. Enter the host informatio n in the followi ng fields: 5. Select OK to save the configuration. The DHCP Co nnections window will display the Static Connection.
2-28 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced IPSec (IP Security) IPSec (IP Security) IPSec (IP security) is a standard for securing IP commun ications by encrypting and/or authenticating all IP packets. IPSec provides security at the network level.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-29 Advanced IPSec (IP Security) General IPSec Settings Field Definition Block Unauthorized IP When an IP address fails to register with IPSec connection, it can be blocked for a set amount of time by the firewall.
2-30 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced IPSec (IP Security) Key Management 1. Select Advanced/ IPSec . 2. Select the Settings button. 3. The Settings window displays the Adit’s public key. If necessary, you can copy the public key from this window.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-31 Advanced IPSec (IP Security) Log Settings Use the IPSec Log Settings window to specify the type of information to be displayed in the IPSec Log. NOTE: The IPSec log is displayed in the System Log ( Syste m Monitoring/System Log ).
2-32 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced IPSec (IP Security) Creating a New Secured Connection 1. Select New Connection on the Internet Protocol Security (IPSec) window. 2. Follow the instructions provided in the series of screens presented.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-33 Advanced NAT/FW Connections NAT/FW Connections The NAT Firewall Connec tions table displays all active NAT and Firewall connections.
2-34 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Network Objects Network Objects The Network Objects window will create a Network Obje ct, which is a set of host names, IP address or MAC addresses. Network Objects allow security ru les to be applied to a distinct LAN subset.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-35 Advanced Network Objects 5. Set the following fields: 6. Click OK . The newly created Network Object appears in the Network Objects table. Field Definition Network Object Type IP Address - Enter the IP address of the Network Object.
2-36 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced PPTP (Point-to-Point Tunn eling Protocol) PPTP (Point-to-Point Tunneling Protocol) The Adit can be configured as a Point-to-Point Tunneling Protocol Server (PPTP Server), accepting PPTP client connection requests.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-37 Advanced RADIUS Client RADIUS Client For authentication to function, the client’s transm ission must go throug h the Adit and reach the back- end server that performs the actual authentication.
2-38 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Remote Administration Remote Administration In it’s default state, the Adit locks all external users from connecting to or communicating with your network. Therefore the system is safe from hackers who may try t o intrude on the network and damage it.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-39 Advanced Restart Restart This option allows the user to re b o ot the Adit 3000 or MSR card. Restarting the System 1.
2-40 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Restore Defaults Restore Defaults The Restore Defaults option sets the Adit back to its factory settings.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-41 Advanced Routing Routing The Advanced/Routing feature provides access to configuration options for the following: Static Routing RIP OSPF Static Routing Select Advanced/Routing to view the routi ng table rules.
2-42 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Routing Adding a New Route 1. Select Advanced/ Routing . 2. Select New Route ..
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-43 Advanced Routing 3. Set the following fields: 4. Select OK . Field Definition Name Select a name from the Pulldown menu. Destination This is the destin ation host, subnet add ress, network address, or default route.
2-44 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Routing Editing a Route 1. Select Advanced/ Routing . 2. Select a Route listed on the Routing Table (clic k on the name, or select the edit icon). 3. Modify settings as needed and select OK.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-45 Advanced Routing Deleting a Route 1. Select Advanced/ Routing . 2. Select Action/Delete icon, to remove the Route listed on the table.
2-46 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Routing RIP Select Advanced/Routing and click on the RIP tab. The RIP window allows you to enable RIP routing.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-47 Advanced Routing OSPF Select Advanced/Routing and click on the OSPF tab. The OSPF window allows you to enable OS PF routing.
2-48 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Routing OSPF Field Definitions When the Open Shortest Past First (OSPF) option is enabled, the window displays additional fields: Field Definition Routing Protocols Open Shortest Pa th First (OS PF) Enables OSPF.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-49 Advanced Routing Area Authentica tion Type None - Set the Area Auth entication to none. Simple Authentication - Enable Simple Authentication Authentication on the OSPF Area. Message-Digest - Enable Message-Digest Authentication on the Area.
2-50 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Routing Configuring OSPF NOTE: For interface OSPF configuration information, see OSPF Configuration on the Network Connection on page 3-40. 1. Select Advanced/ Router . 2. Select the OSPF tab.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-51 Advanced Routing 10. Enter the Network IP Address of the Neighbor to add to the OSPF Network. 11. Enter an IP address mask th at includes "don’t c are" bits. 12. Select OK . The new address appears in the Network Address Table.
2-52 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Scheduler Rules Scheduler Rules To create a scheduling rule: 1. Select Advanced/Sched uler Rules . 2. Select New Schedule r Entry . 3. Enter a name for the rule in the Name field (maximum of 64 characters).
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-53 Advanced Scheduler Rules 5. Select New Time Segment Entry to define the day(s) of th e week to apply the rule to. Note: At a minimum, one day must be selected. 6. Under Hours Range , select New Time Segmen t Entry to define the Start and End time.
2-54 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Scheduler Rules 7. Select OK for each window until at the Scheduler Rules table. The new rule appears in the table.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-55 Advanced Simple Network Management Protocol Simple Network Management Protocol SNMP enables network management sy stems to remotely configure and monitor the Adit. Your Internet Service Provider (ISP) may use SNMP to identify and resolve technical problems.
2-56 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Simple Network Management Protocol 3. Set the Trusted Peer . This is the IP address and subn et that identifies which remote management stations are allowed t o perform SNMP operation on the Adit.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-57 Advanced System Settings System Settings Select Advanced/System Settings to view and modify general system settings . As shown in the screen shots on th e following pages, the syst em settin gs differ slightly between the Adit 3000 and MSR.
2-58 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced System Settings Adit 3500.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-59 Advanced System Settings Adit MSR.
2-60 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced System Settings Defining an Outgoing Mail Server Features that require the Adit to send e-mail (example: e-mail notific ation) require an outgo ing SMTP server to be defined. 1. Enter the host name of yo ur outgoing SMTP server in the Server field.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-61 Advanced Technical Information Technical Information Select Advanced/Technical Information to view technical informatio n about the system, including software version numbers and contact information.
2-62 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Technical Info rmation Adit MSR.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-63 Advanced Technical Information Configuration File The Configuration File button on the Technical Information wind ow displays the current configuration file for the syst em. The configur ation file can be saved, modified, and reloaded, if necessary.
2-64 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Upgrade Fr om a Local Com puter Upgrade From a Local Computer This feature allows the user to easily upgrade the Adit software. Upgrading the Software 1. Select Advanced/ Upgrade From a Loca l Computer .
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-65 Advanced Users Users Use this feature to view, add, edit, and delete user s on the device, and to co nfigure e-mail notification.
2-66 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Users Adding a User 1. Select Advanced/ Users . 2. Select New User a nd enter the followin g General information: 3. Select OK . Field Definition General Full Name The user’s full nam e. User Name The name this user will en ter (as user name) to access this network.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-67 Advanced Users Editing a User 1. Select Advanced/ Users . 2. Select the Action/Edit icon of an existing User.
2-68 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced Users Configuring E-mail Noti fication for Users The e-mail notification feature allows users to receive e-mail notification of system events of a defined type or severity. 1. Select Advanced/ Users .
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-69 Advanced VLAN Configuration VLAN Configuration The Virtual Local Area Network (VLAN) feature prov ides a way to logically group network devices that are in a Wide Area Network (WAN) and enable them to communicate as if they were in a Loc al Area Network (LAN).
2-70 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced VLAN Configuration Configuring a VLAN 1. Select Advanced/ VLAN Configuration . 2. Select Enable VLAN (dot1q) Tagging in all Ports .
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-71 Advanced VLAN Configuration 4. Enter a VID (VLAN ID number) for the VLAN. Range is 2-4094 . 5. Set the Priority level, if needed. Range is 7-0. 6. Select the VLAN Members (Ethernet or VoIP) of this VLAN by checking the associated box.
2-72 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced VLAN Configuration Configuring the VLAN Port Setting 1. Select Advanced/ VLAN Configuration.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 2-73 Advanced VLAN Configuration 3. Configure the port as ne eded. 4. Select OK to save changes. Field Definition Enable VLAN (dot1q) tagging This checkbox enables VLAN tagging on this port. Default is disabled (unchecked).
2-74 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Advanced VLAN Configuration.
C HAPTER 3 Network Connections In this Chapter Overview - Adit 3000 Connections - Adit MSR Connections Preconfigured Connections - Ethernet 1 - Ethernet 2 - Serial 1 (Adit 3000 Only) - T1 1 - .
3-2 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Network Connections Overview Overview The Network Connection window allows the user to create and configure netw or k connections. For the Adit 3000, the basic connections fo r the system are preconfigured.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 3-3 Network Connections Overview Adit MSR Connections The MSR provides the following connections: LCC 1-8 – Link Cross-Connects (LCCs) are resources that can be cross-conne cted to Adit 600 resources.
3-4 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Network Connections Overview.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 3-5 Network Connections Preconfigured Connections Preconfigured Connections The following connections that may be preconfigured on the system. Note: When the system is set back to its default settings, these co nnections will all be reset to this original configuration.
3-6 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Network Connections Preconfigured Connections Configuring Ethernet 1 To change the configuration of Ethernet 1, select the Settings button and modify the settings as necessary. Select Apply when finished.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 3-7 Network Connections Preconfigured Connections NOTE: For a ma nually specified network mo de (Interne t Protocol: Use the following IP address), the default route does no t get inst alled until both the Default Route checkbox is enabl ed AND the user has entered a valid non-0.
3-8 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Network Connections Preconfigured Connections Configuring DHCP Options To configure DHCP options: 1. From the Configure Ethernet 1 windo w, select DHCP Server for IP Address Distribution. 2. Select the DHCP Options field.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 3-9 Network Connections Preconfigured Connections Ethernet 2 The Ethernet 2 Properties window displays the current settings of the connection. This connection is set up as a default, and can be enable d or disabled, but cannot be deleted.
3-10 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Network Connections Preconfigured Connections Configuring Ethernet 2 To change the configuration of Ethernet 2, select the Settings button and modify the settings as necessary. Select Apply when finished.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 3-11 Network Connections Preconfigured Connections NOTE: For a ma nually specified network mo de (Interne t Protocol: Use the following IP address), the default route does no t get inst alled until both the Default Route checkbox is enabl ed AND the user has entered a valid non-0.
3-12 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Network Connections Preconfigured Connections Serial 1 (Adit 3000 Only) The Serial 1 (PPPoDS0) Properties window will display the current se ttings of the connection., and can be enabled, disabled, deleted or modified from this window.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 3-13 Network Connections Preconfigured Connections T1 1 - T1 4 (Adit 3000 Only) There can be up to four preconfigure d T1 connections on the Adit 3000. To view /modify the configuration, click on the T1 n name on the Network Connections window.
3-14 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Network Connections Preconfigured Connections Configuring a T1 (1-4) The Configure T1 n (1-4 ) window displays all of the T1 configuration para meters and the default settings for each. To configure a T1, select the Settings button, the Configuration window will display.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 3-15 Network Connections Preconfigured Connections Log Button See, System Monitoring/ T1 Log (Adit 3000 Only) on page 5-7. Performance Button See, System Monitoring/ T1 Performance (Adit 3000 Only) on page 5-10.
3-16 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Network Connections Connections that Requ ire Configuration Connections that Require Configuration The following conn ection types must be configured using the New Conne ction selection.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 3-17 Network Connections Connections that Require Config uration Multilink The Multilink Properties window displays the settings of a Multilink PPP over DS0 connection configured with the New Connection option.
3-18 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Network Connections Connections that Requ ire Configuration.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 3-19 Network Connections Connections that Require Config uration The following are field definitions for the Confi gure Multilink 1 window: Field Definition General Device Name Displays the device name. Status Displays the current s t atus.
3-20 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Network Connections Connections that Requ ire Configuration NOTE: The Adit uses the compressed format of pr otocol encapsulation, which me ans it uses a 1-byte protocol instead of 2 bytes.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 3-21 Network Connections Connections that Require Config uration Serial (PPPoDS0) The Serial Properties window displays the settings of a Serial PPP over DS0 co nnection. For the MSR, this connection must be configured with the New Connec tion option.
3-22 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Network Connections Connections that Requ ire Configuration.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 3-23 Network Connections Connections that Require Config uration The following are field definitions for the Configure Serial 1 window: Field Definition General Device Name Displays the device name. Status Displays the current status.
3-24 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Network Connections Connections that Requ ire Configuration DNS Static Entries (This name is a link to the Advanced / DNS Static En tries window.) Obtain DNS Server Address Automatically Sets the interface to obtain a DNS Server address.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 3-25 Network Connections Connections that Require Config uration Underlying Device - High Speed Serial Configuration (Adit 3000 Only) To configure the individual channels in the Serial 1 (PPPoT1) or Multilink connection, select the T1 name listed in the Underl ying Device field.
3-26 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Network Connections Connections that Requ ire Configuration Field Definition Assignment Data - Sets the channel type to Data.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 3-27 Network Connections New Connection New Connection There are a variety of options for creating a New Connection . The following sectio ns walk through each option. NOTE: For information on modifying thes e connections after setup, see Connections that Require Configuration on page 3-16 .
3-28 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Network Connections New Connection New Connection Window.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 3-29 Network Connections New Connection Point-to-Point Protocol over DS0 (Serial) PPPoDS0 (Serial) creates a connection to the Internet using a PPP tunnel over HDLC. This configuration creates a Serial 1 connection listed on the Network Co nnections table.
3-30 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Network Connections New Connection 5. Select Next > . 6. The Connectio n Summary window disp lays the current configuration. Select 3 Finish if information is correct. Select < Back to modify th e configuratio n.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 3-31 Network Connections New Connection 7. The new Se rial connection appear s on the Network Connections window.
3-32 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Network Connections New Connection Multilink Point-to-Point Protocol over DS0 (Multilink) Multilink creates a connection to the Internet usin g a MLPPP tunnel over HDLC. This configuration creates a Multilink 1 connection listed on the Network Connec tions table.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 3-33 Network Connections New Connection 5. Select Next > . 6. The Connection Summary window displays the current co nfiguration. Select 3 Finish if information is correct. Select < Back to modify th e configuration.
3-34 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Network Connections New Connection Point-to-Point Tunne ling Protocol (PPTP) Point-to-Point Tunneling Protocol enables secure tran sfer of data to another location over the Internet. 1. Select Network Connections/New Connection .
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 3-35 Network Connections New Connection Point-to-Point Tunneling Prot ocol Server (PPTP Server) PPTP Server enables Virtual Private Network (VPN ) connections to y our home network from o ther locations.
3-36 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Network Connections New Connection 6. Select Next > . 7. Select 3 Finish ..
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 3-37 Network Connections New Connection Layer Two Tunneling Protocol (L2TP) L2TP enables secure transfer of data to another location over the Internet. 1. Select Network Connections/New Connection. 2. Select Layer Two Tunneling Protocol (L2TP) , then select Next > .
3-38 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Network Connections New Connection Internet Protocol Security (IPSec) IPSec enables secure transfer of da ta to another location over the Inte rnet, using private and public keys for encryption, and digital certificates for authentication.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 3-39 Network Connections New Connection 4. Select the Remote Address and Subnet types, and select Next > . Note: The following example assumes a selection of Network-to-Network/Remote Gateway Address and Remote Subnet .
3-40 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Network Connections OSPF Configur ation on t he Network Conn ection OSPF Configuration on the Network Connection OSPF can be set as the routin g pr.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 3-41 Network Connections OSPF Configuration on the Netwo rk Connection 3. At the Configure Ethernet 1 window, select OSPF from the Routing Protocols pulldow n menu. Click on the OSPF Configuration link under the pulldown menu.
3-42 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Network Connections OSPF Configur ation on t he Network Conn ection 4. Set the OSPF interface parameters as needed: Field Definition Interface Authentication Interface Authentication Type None - Set the OSPF Authentication to none.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 3-43 Network Connections OSPF Configuration on the Netwo rk Connection Interface Cost Defines the cost of sending a packet on th is interface. Range is 1-65535, with a default of 0. Interface Priority Defines the router priority, which determ ines the designated router for this network.
3-44 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Network Connections OSPF Configur ation on t he Network Conn ection.
C HAPTER 4 Security In this Chapter Overview General Access Control Local Servers DMZ Host Port Triggering Remote Administration IP/Hostname Filtering Advanced Filt.
4-2 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Security Overview Overview The Adit 3000 and MSR include c omprehe nsive and robust security services: Stateful packet inspection firewall U.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 4-3 Security Overview The following sections describe each of th e tabs available at the Security window: General Access Control Local Serve.
4-4 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Security General General Use the Gene ral tab to configure the Ad it’s basic security settings. The firewall regulates the flow of data between the network and th e Internet.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 4-5 Security General The important thing to note is that it is the origin of the request, not su bsequent responses to this request, that determines whether a session can be establishe d or not.
4-6 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Security Access Control Access Control Use the Access Control tab to define a rule to block spec ific network devic es with in the network from accessing certain services on the Internet.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 4-7 Security Access Control Adding an Access Control Rule To add an access control rule: 1. Select New Entr y on the Security/Access Control w indow to display the Add Access Control Rule window.
4-8 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Security Access Control 4. Select the service(s) to block. Note: The Service table is used by multiple wi ndows; the standard services and the User- Defined services created on any of these windows will appear here.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 4-9 Security Access Control Modifying an A ccess Control Rule Rules can be enabled/disabled by ch ecking/unchecking the rule listed on the Security window. Rules can be modified by selecting the Edit button for the rule and modifying the configuration.
4-10 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Security Access Control Creating a User-Defined Rule 1. At the Add Access Control Rule window, select the New User-Defined Service field. 2. Name the service and give a description, if needed. 3. Select a Server Port from the list, or select New Server Ports to create one.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 4-11 Security Access Control 4. Configure the Service po rt protocol: Field Definition Protocol TCP - Transmission Control Protocol. TCP is a transport layer, connection -oriented, end-to-end protocol. It provides reliable, sequenced, and unduplicated del ivery of bytes to a remote or local user.
4-12 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Security Access Control 5. Select OK to save. The newly crea ted serv ice port is listed in the table. 6. Select OK to save the User-Defined Se rvice. The ne w service is listed (with a checkbox) in the table.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 4-13 Security Local Servers Local Servers By default, the Adit blocks all ex ternal users from connecting to or communicating w ith your network . Therefore the system is safe from hackers who ma y try to intrude on the network and damage it.
4-14 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Security Local Servers Additionally, Local Servers enable you to redirect tra ffic to a port different than the specified port.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 4-15 Security Local Servers 2. Enter the local IP address of the computer that will provide the se rvice (server) in the Local Host field . Note: Only one LAN computer an be as sign ed to provide a specific service or application.
4-16 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Security Local Servers Modifying a Local Server A Local Server can be enabled/disabled by simply checkin g/unchecking the server listed on the Security window. A Local Server can be modified by selecting the Edit button for the server and modifying the configuration.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 4-17 Security DMZ Host DMZ Host The DMZ (Demilitarized Zone) Host fe ature allows one local computer to be exposed to the Internet.
4-18 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Security DMZ Host Designating a Local Co mputer as a DMZ Host To designate a local computer as a DMZ host, en ter the IP addre ss of the computer at the Security/DMZ Host window. You can enable/disable the DMZ host at any time by checkin g/unchecking the checkbox next to the host.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 4-19 Security Port T riggering Port Triggering Port triggering can be used for dynamic port forwar ding. By setting port triggeri ng rules, you can allow inbound traffic to arrive at a specific LAN host, us ing ports different than th ose used for the outbou nd traffic.
4-20 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Security Port Triggering Setting up Port Triggering To set up port triggering : 1. Select New Entry on the Security/Port Triggering window. 2. Select a previously defined service under User-Define d Services , or select New User -Defined Service .
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 4-21 Security Port T riggering 3. If creating a New User-Defined Service : a. Enter a Service Name and Service Description . b. Under Server Ports , select a configured port from the lis t, or create a new port by select- ing New Server Ports (see Configur e the Service port protocol: on page 4-1 1 ).
4-22 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Security Port Triggering d. Select OK . The new triggering service is listed in the table. e. Select the checkbox next to the new service, and select OK . The new triggering service is enabled and available for selection.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 4-23 Security Remote Administration Remote Administration It is possible to access and control the Adit not only from within the netw ork, but also from the Internet. This allows you to view or change settings while traveling.
4-24 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Security Remote Administration Configuring Remote Administration To configure remote access to Adit administration services: 1. Select Security/Remote A dministration . 2. Select the services that you would like to make available to computers on the Internet.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 4-25 Security IP/Hostname Filtering IP/Hostname Filtering You can configure the Adit to block specific IP addr esses or hostnames so that they can not be accessed from computers in the network.
4-26 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Security IP/Hostname Filtering Adding an Address/Hostname to the Restricted List To add a restricted IP address or hostname: 1. Select New Entry on the Security/ IP/Hostname Filtering window. 2. Enter an IP Address or Hostname .
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 4-27 Security IP/Hostname Filtering 5. Select OK to add the Address to the Restricted list. 6. If the site is successfully located, the Status on the IP/Hostname Filtering window will transition from Resolving.
4-28 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Security Advanced Filtering Advanced Filtering Advanced filtering is designed to allow comprehensive co ntrol over the firewall’s behavior.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 4-29 Security Advanced Filtering Adding an Advanced Filtering Rule To add a new advanced filtering rule: 1. Select Security/ Advanced Filtering . 2. Select the rule set to modify (for ex ample, in the Input Rule Sets, select Initial Rules ).
4-30 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Security Advanced Filtering 4. On the Add Advanced Filter window, define the filter (see field definitions below).
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 4-31 Security Advanced Filtering Field Definition Matching - Use this sect ion to defin e the rule’s condition s. Source IP Address The Source IP address of packets sent or received from the LAN computer.
4-32 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Security Advanced Filtering 5. Select OK to save and enable the rule . The rule is listed in the Configure Initial Rules table.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 4-33 Security NAT Bypass NAT Bypass The Security/NAT Bypass feature allows network address tran slation to be bypassed for specific addresses or networks. Y ou can add, modify, and re move NAT bypass rules.
4-34 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Security Security Log Security Log The Security Log displays a list of firewall-related events, including attempts to establish inbound and outbound connectio ns, attemp ts to authenticate at an administrati ve interface, firewall configuration, and system startup.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 4-35 Security Security Log Changing the Security Log Settings To change the settings for the Security Log: 1. Select Security/ Security Log . 2. Select Settings . 3. Modify the settings as necessary (see the following table), then select OK .
4-36 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Security Security Log Security Log Settin gs Field Definition Accepted Events Accepted Incoming Connections Sessions originated from the Inte rnet that have been allowed by the firewall. Accepted Outgoing Connections Sessions or iginated from t he network th at have been all owed by the firewall.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 4-37 Security Firewall Implementation Firewall Implementation The Adit provides very powerful NAT and firewall capabilities.
4-38 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Security Firewall Implementation Routing Mode The routing mode determines whether NAPT (Network Address Port Translation) is applied to sessions that are created through this inte rface.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 4-39 Security Firewall Implementation Firewall Processi ng Sequence This section details the sequence of process ing that is used by the firewall when examining packets. This detail can help an experienced user better un derstand the order o f application o f each of the various security settings.
4-40 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Security Firewall Implementation Outbound Firewall Processing The following table describes the sequence of exam ination of packets depa rting from the interface. This firewall processing is applied after the IP stack and before passing th e outbou nd packet down to the layer 2 driver.
C HAPTER 5 System Monitoring In this Chapter Overview Connections Traffic System Log T1 Log (Adit 3000 Only) SIP Log PRI Log T1 Performance (Adit 3000 Only) Alarms .
5-2 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI System Monitoring Overview Overview The System Monitoring w indow displays inform ation that can be used for mo nitoring and troubleshooting the system.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 5-3 System Monitoring Overview Adit MSR.
5-4 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI System Monitoring Connections Connections The Connections tab displays all the connections, their stat us, and other information specific to each connection.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 5-5 System Monitoring Traffic Traffic The Adit is constantly mo nitoring traffic withi n the local netw ork and between the local network and the Internet.
5-6 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI System Monitoring System Log System Log The System Log displays a list of the most recent ac tivity that has taken place on the network.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 5-7 System Monitoring T1 Log (Adit 3000 Only) T1 Log (Adit 3000 Only) The T1 Log displays all T1 related alarms and events for the Adit 3000.
5-8 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI System Monitoring SIP Log SIP Log The SIP Log displays all SIP rela te d alarms and events. Field Definition Enable SIP Logging Use this checkbox to enable (ch eck) or disable (unchecked) SIP logging.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 5-9 System Monitoring PRI Log PRI Log The PRI Log displays all PRI related alarms and events. Field Definition Enable PRI Logging Use this checkbox to enable (ch eck) or disable (unchecked) PRI logging. PRI Log Size Configure the PRI log size.
5-10 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI System Monitoring T1 Performance (Adit 3000 Only) T1 Performance (Adit 3000 Only) The T1 1 through T1 4 Performance tabs display the performance sta tistics for each of the Adit 3000’s T1s.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 5-11 System Monitoring Alarms Alarms The Alarms tab displays the system alar ms, their severity, and the time at which each event occured.
5-12 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI System Monitoring System System The System tab displays the amount of time that has passed since the syste m was last started or reset.
C HAPTER 6 Voice Over IP NOTE: This feature is not available on the Adit 320 0. In this Chapter Overview IP Telephony Phone Settings Phone Book Line Monitoring Trunk Settings .
6-2 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Voice over IP Overview Overview The VoIP feature allows you to co nnect multiple phones ove r a single broadband connection, providing the benefits and quality of digital voice. The Adit enable s you to place and receive calls over the Internet using a standard telephone set connected to the Adit.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 6-3 Voice over IP IP Telephony IP Telephony Use the IP Telephony tab to configure VoIP dialing parame ters, signaling protocols, and codecs.
6-4 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Voice over IP IP Telephony Field Definition Dialing Parameters Dialing Timeout Determines how long t he system will wait for the next dialed di git before stopping digit-collectio n.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 6-5 Voice over IP IP Telephony Proxy Servers Proxy Type This drop-down menu allo ws users to select the proxy type: Generic BroadSoft (Info) Sylantro Lucent (Info) Route Direct Phone Entries in Phone book through Proxy Select the checkbox to enable.
6-6 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Voice over IP IP Telephony Configuring the Di git Map The Digit Map is used to define ph one-specific dialing behavior. A dial plan allows the phone to identify that an entered number is complete and the call should be initiated.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 6-7 Voice over IP IP Telephony 4. Select New Entry to create a new Digit Map pattern, or select the Edit icon to modify an existing one.
6-8 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Voice over IP IP Telephony Digit Map Pattern A Digit Map Pattern consists of a sequence of one or more of the following character or string elements: The maximum n umber of characters in t he string is 500.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 6-9 Voice over IP IP Telephony Advanced (Button) The Advanced button at the bottom of the IP Telephony windo w opens a window for configuring the Advanced VoIP (SIP) settings.
6-10 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Voice over IP IP Telephony Field Definition SIP Intero p Calling Feature Mode Determin es where the intelligence for the calling features will lie , offering a choice between server-based (Info) a nd device-based (local) features.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 6-11 Voice over IP IP Telephony FXS Signaling Calling Party Disconnect (CPD) Duration Allows the user to configure the disconnect timeout for in dividual lines.
6-12 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Voice over IP IP Telephony Redundancy (Button) The Redundancy button at the bottom of the IP Telephony window open s a window for configuring VoIP proxy redund ancy. Note: This window is modified upon selection of th e Global Redundancy Configuration field.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 6-13 Voice over IP IP Telephony When the primary proxy is not rea chable or returns an error, the system initi ates a rollover (the next server in the list is used, until a worki ng server replies). When the last server in the list fails, the rollover is considered a rollback.
6-14 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Voice over IP Phone Settings Phone Settings Use the Phone Settings tab to configure each line for VoIP. NOTE: When connecting analog lines to the PBX, impedance settings c an be used to match impedance between the analog interfaces.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 6-15 Voice over IP Phone Settings Adit MSR NOTE: To display all available lines on the MSR, select Displ ay All Lines .
6-16 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Voice over IP Phone Settings Configuring Phone Settings 1. Select the Phone Settings tab on the Voice over IP window. 2. Select the Action icon for the line to configure. 3. Set the Line Settings as desired.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 6-17 Voice over IP Phone Settings Field Definition Identification Begin Line Number Displays the lin e number th at was selected to edit. End Line Number Specifying a line numb er here allows a user to define a range to apply the settings to.
6-18 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Voice over IP Phone Settings Signaling Proto col Select the analog signaling mechanism: Loop Start - Sets the line to Loop Start signaling. Ground Start - Sets the line to Ground Start signaling. Note: For the MSR, this field is not selectable.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 6-19 Voice over IP Phone Book Phone Book Use the Phone Book tab to define the Speed Dial settings. You can define a maximum of 50 entries.
6-20 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Voice over IP Phone Book Configuring Phone Book Settings 1. Select Voice over IP/Phone Book tab. 2. Select New Entry . Note: This window modifies as the Destination field is changed. See the following table for field definitions.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 6-21 Voice over IP Phone Book Field Definition Phone Book Enter the Speed Dial number. Range is 3-10 digits. This is the number that needs to be dialed to get to this entry. Digits allowed 0-9, #, *, ?, $.
6-22 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Voice over IP Line Monitoring Line Monitoring The Line Monitoring tab d isplays current in formation for each line.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 6-23 Voice over IP Line Monit oring Adit MSR.
6-24 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Voice over IP Line Monitoring The following table defines the fields displayed in the Line Monitoring window: Field Definition Registration Addre ss Adit WAN IP address. Blank if a proxy ha s not been selected.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 6-25 Voice over IP Trunk Settings Trunk Settings NOTE: The Trunk Settings tab is only available on the Adit 3500 and Adit MSR.
6-26 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Voice over IP Trunk Setting s Configuring Trunk Settings To configure the trunk : 1. Select the Voice Over IP/Trunk Settings tab. 2. Select the Trunk . The Trunk Settings window appears. See the following table for field definitions.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 6-27 Voice over IP Trunk Settings Field Definition General Connection Adi t 3500: Connections are T1 #1 thro ugh T1 #4. Select the checkbox for the T1 to apply the trunk settings to. Note: A red X indicates that the T1 is not available.
6-28 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Voice over IP Trunk Setting s Identification Trunk ID Display/edit th e Trunk ID. A defau lt ID is assigned. The Trunk ID can have up to 20 characters. Description Display/edit a Trunk Description. By default they are named Trunk n .
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 6-29 Voice over IP Trunk Settings Digit Map Per Trunk Digit Map Disabled - Use the phone book, maximum digits, or dialing timeout to determine end of dialing.
6-30 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Voice over IP Trunk Setting s Channel Configuration The Channel Configuration window displays the communicatio n assignment for each channe l in the trunk. For the Adit 3500, you can change the channel assignments at this wind ow.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 6-31 Voice over IP Trunk Settings Field Definition Assignment in-out - Allows comminution in both direct ions. Default. in - Allows communication in the IN direction only. out - Allows communicatio n in the OUT direction only.
6-32 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Voice over IP Trunk Monit oring Trunk Monitoring NOTE: The Trunk Monitoring tab is only available on the Ad it 3500 and Adit MSR. The Trunk Monitoring window displays current status and statistic s for trunk channels.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 6-33 Voice over IP Trunk Monitoring Adit MSR.
6-34 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Voice over IP Trunk Monit oring The following table defines the fields displayed in the Trunk Monitoring window: Field Definition PRI Interface - For each PRI interface the following is displayed: LapdStatus The operational status of the LAPD (Link Acces s Procedure on the D channel) status.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 6-35 Voice over IP Trunk Regist ration Trunk Registration NOTE: The Trunk Registration tab is only available on the Adit 3500 and Adit MSR. The Trunk Registration tab displays all config ured PBX phone lines.
6-36 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Voice over IP Trunk Registration Adding a PBX Phone Line To add a new PBX phone line: 1. Select New Entry from the Voice Over IP/Trunk Registration window.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI 6-37 Voice over IP Trunk Regist ration 2. Enter the PBX line information. See th e following table for field definitions. Field Definition Fast Configuration First Phone Number Index Enter an index number for the phone number.
6-38 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Voice over IP Trunk Registration 3. Select OK to enter the number and return to the Trunk Registration window.
G LOSSARY AMI Automatic Mark Inversion ARP Address Resolution Protocol B8ZS Bipolar with 8 Zero Substitution BIT Binary Digit BPS Bits Per Second BPV Bipolar Violation CA Certificate Authority CAS Cha.
Glossary-2 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Glossary DLC Digital Loop Carrier DLCI Data Link Connection Identifier DMZ Demilitarized Zone DNS Domain Naming Sys tem DS0 Digital Signal Level Zero (64 kbps) (1 voice channel) DS1 Digital Signal Level 1 (1.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Glossary-3 Glossary MPPE Microsoft Point-to-Point Encryption MS-CHAP Microsoft CHAP MVEC Majority Vote Error Correction NAT Network Address Transl ation.
Glossary-4 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Glossary UAS User Agent Server VC Virtual Channel VLAN Virtual Local Area Network VPN Virtual Private Network WAN Wide Area Network WINS Wind.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Glossary-5 Glossary 10Base-T The most widely installed Ethernet local area networks (LANs) use ordinary telephone twisted-pair wire. When used on Ethernet, this carrier medium is known at 10BASE-T. 10BASE-T supports Ethernet’s 10 Mbps transmission speed.
Glossary-6 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Glossary Central Office (CO) Where telephone companies terminate customer lines and locate switching equipment to interconnect those l ines with other networks.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Glossary-7 Glossary Electro-magnetic Interference (EMI) Equipment used in high speed data systems, includin g ATM, that generate and transmit many signals in the radio frequenc y portion of the electromagnetic spectrum.
Glossary-8 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Glossary gateway An entrance and exit into a communications network Graphical User Interface (GUI) GUI, pronounced “GOOEY”. A set of screen pr esentations and metaphors th at utilize graphic elements such as icons in an attemp t to make an operating system easier to use.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Glossary-9 Glossary Local Area Network (LAN) A short distance data co mmunications networ k (typically within a building or campus) used to link together computers and peripheral devices under some form of st andard control.
Glossary-10 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Glossary Multilink PPP (MLPPP) Mul tiLink PPP. An extension to the point-t o-point protocol that enable s two channels to be linked together to double the throu ghput.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Glossary-11 Glossary PHY PHY as in physical specificatio ns. OSI Physical Layer, which provid es for transmission of cells over a physical medium connecting two ATM devices. ping Packet InterNet Grouper.
Glossary-12 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Glossary Router Information Protocol (RIP) RIP is based on distance vector algorithms that measure the shortest path between two points on a network, based on the addresses of the originating and destination devices.
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Glossary-13 Glossary ticks The distance between two networks, measured in time increments. Ticks may be used to designate primary and secondary routes to the same network. traffic The load of packets carried by a network or portion of a network.
Glossary-14 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Glossary.
I NDEX A Access Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6 Action icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 add a user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index - 2 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Index Redundancy button . . . . . . . . . . . . . . . . . . . . . . . . 6-12 IP Telephony tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3 IP/Hostname Filtering . . . . . . . .
Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Index - 3 Index S Scheduler Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-52 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22 , 4-1 Access Control . . . . .
Index - 4 Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) GUI Index Remote Administrati on . . . . . . . . . . . . . . . . . . . . . 2-38 Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-39 Restore Defaults . . . . . . . . . .
Ein wichtiger Punkt beim Kauf des Geräts Carrier Access MSR/Adit 3K GUI (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Carrier Access MSR/Adit 3K GUI noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Carrier Access MSR/Adit 3K GUI - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Carrier Access MSR/Adit 3K GUI reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Carrier Access MSR/Adit 3K GUI erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Carrier Access MSR/Adit 3K GUI besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Carrier Access MSR/Adit 3K GUI verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Carrier Access MSR/Adit 3K GUI. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Carrier Access MSR/Adit 3K GUI gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
