Benutzeranleitung / Produktwartung IC Communication Adapter ICA93LV des Produzenten Calibre UK
Zur Seite of 27
Revision 1.7 09/12/1999 ICA93LV I 2 C Communications A dapter User Ma nual Contents 1. Introduction 1 1.1. Pack ing List 1 2. Configuring the Adapter 2 2.1. Setting the Adapter Base Addres s 2 2.2. W ait State Generator 2 2.3. Interrupt Generation 3 2.
Revision 1.7 Page 1 of 27 09/12/1999 1. Introduction The I 2 C Com m unications Adapter is a half length PC inter face c ard des igned to f it any IBM PC com patible expansion slot. Based on the Philips PCF8584 bus c ontroller, it f eatures f ull I 2 C bi-directional com patibility as either a m aster or slave.
Revision 1.7 Page 2 of 27 09/12/1999 2. Configuring the A dapter NOTE: MANY COM PONENT S ON THE ADA PTER CARD A RE STATIC SENSIT IVE. OBSERVE NORM AL STA TIC SENSIT IVE PRECA UTION S WHEN HANDLING THE CA RD! The adapter is supplied in a sta ndard configuration which should suit most applications.
Revision 1.7 Page 3 of 27 09/12/1999 Important Note: Due to the internal operation of the ICA93, it must not be accessed o ver the PC bus (read or w ritten) more than o nce every nine of it s own clock cycles. The ICA93 is clocked at 12MHz ; therefore it MUST NOT be accessed more than once ev ery 0.
Revision 1.7 Page 4 of 27 09/12/1999 3. Conn ecting th e A dapter to your System 3.1. Connec tor Pinout All external connec tions are m ade via a 9 way “D” sock et: Pin Norm al Mode 10 V 20 V 30 V.
Revision 1.7 Page 5 of 27 09/12/1999 4. Getting Star ted 4.1. Resetting t he A dapter A reset forces the adapter into a well defined state, ready for initialisation. T he card uses the sam e reset line as the PC so either a power up or hard reset ( press the <RESET> button on your PC) will suff ice.
Revision 1.7 Page 6 of 27 09/12/1999 5. Using the Utilities Each utility is documented in a s tandard for mat, which lis ts its nam e, usage, f unction, and ef fect on the adapter is given. Following a reset, the adapter should be setup prior to any data transfer .
Revision 1.7 Page 7 of 27 09/12/1999 Parameters are: int controladdress address of I 2 C control r egister. T his is equal to 1+( base address of adapter set by links on circuit board) . Value Returned: int <status> where status is an integer from 0x 00 to 0xFF which indic ates the curr ent status of I 2 C Com munications Adapter .
Revision 1.7 Page 8 of 27 09/12/1999 { int base, slv, setnac k; base = 0x310; /* Adapter’s bas address = 0x 310 (hex) */ slv = 0xa0; /* I 2 C Address of s lave, this is a typical */ /* write for an .
Revision 1.7 Page 9 of 27 09/12/1999 /* This will read a by te of data fr om a slave previously addressed */ /* by and with acknowledge already disabled by sendaddress.
Revision 1.7 Page 10 of 27 09/12/1999 #include <dos.h> /* Optional, but reco mm ended if your compiler */ /* supports DO S I/0 functions */ #include <i2c.
Revision 1.7 Page 11 of 27 09/12/1999 Name: setup (baseaddr%, own%, sc lk%) Usage: call setup(bas eaddr%, own%, sclk %) Function: procedure to s et up I 2 C Comm unications Adapter. Parameters are: baseaddr% base address of adapter s et by links on circuit board.
Revision 1.7 Page 12 of 27 09/12/1999 baseaddr% = &h310 ‘* adapter’s base addr ess = 0x310 ( hex) * controladdres s% = baseaddr % + 1 status% = FNgets tatus%(contr oladdress%) print”I 2 C Com m unications Adapter Status = “;status % ‘* This will read the I 2 C Comm unications Adapter’s c urrent status * 5.
Revision 1.7 Page 13 of 27 09/12/1999 setnack % this controls whether the I 2 C Com munic ations Adapter trans mits and Ack nowledge down the I 2 C Bus on reception of a byte. The last byte received during a transf er m ust not be ack nowledged, in all other c ases ack nowledge mus t be enabled.
Revision 1.7 Page 14 of 27 09/12/1999 Function: procedure to send a Stop (end of com m unication s ignal) down the I 2 C Bus, ending a transm ission or reception with a slave that was address previously by sendaddress .
Revision 1.7 Page 15 of 27 09/12/1999 slv% = &ha1 ‘* I 2 C Address of slave, this is a ty pical read address * ‘* for an I 2 C s tatic RAM or EEPROM* setnack % = 0 ‘* Enable Ac knowledge (s .
Revision 1.7 Page 16 of 27 09/12/1999 baseaddress is the addres s at which the adapter has been inst alled, e.g. 310H ownaddress I2C address to which the adapter is to res pond in slave mode. T his f orm s the upper 7 bits of the 8 bit addres s, the lowest bit being the read (1) or write (0) bit.
Revision 1.7 Page 17 of 27 09/12/1999 Setnack 1 for no ac knowledge 0 for ack nowledge. Paramete rs returned I 2 Cdata, the data read, if a time-out oc curs the Er rCode 8005H is returned. Prerequisites Adapter m us t be conf igured us ing set up, star t and read address s ent by sendaddress.
Revision 1.7 Page 18 of 27 09/12/1999 getstatus Function spec ification: Int getstatus ( ) Paramete rs returned I 2 Cstatus, the current value of the bus status . Prerequisites Adapter m us t be configur ed using setup. Functional desc ription The f unction reads status word fr om the adapter and returns it.
Revision 1.7 Page 19 of 27 09/12/1999 W hen all the by tes have been transm itted a stop is issued and the total number of bytes is returned. Sendby tes can only be used in mas ter write m ode.
Revision 1.7 Page 20 of 27 09/12/1999 Getbytes can only be used in m aster read m ode. slavelastbyte Function spec ification void slavelastbyte( ) Paramete rs returned none.
Revision 1.7 Page 21 of 27 09/12/1999 6. Furth er Information The f ollowing references m ay be found usef ul when using the adapter: Philips Semic onductor s Tec hnic al Handbook Book 4 Par ts 12a and 12b. T hese give details of the I2C com patible ICs, and the I 2 C Bus specific ation.
Revision 1.7 Page 22 of 27 09/12/1999 7. Th e Real-Time Bu s Mo nitor The progr am REALTIM1.EX E in the MONTO R director y is a completely non-invasive real-tim e bus monitor which records ac tivity on an I 2 C-bus , post-proces ses the data and stores the results in an ASCII file.
Revision 1.7 Page 23 of 27 09/12/1999 A ppendix A I 2 C Communications A dapter S tatus Codes This is an eight bit register, read using the gets tatus routine.
Revision 1.7 Page 24 of 27 09/12/1999 A ppendix B – I 2 C Communic ations A dapter Control Codes The Control Regis ter should norm ally be w ritten using the setup, s endaddress and sends top routines.
Revision 1.7 Page 25 of 27 09/12/1999 A ppendix C - T he M ost Commonly Asked I 2 C Questions General Ques tions Question Will my adapter work in a Pentium PC? Answer Y es and there is no need to alter LK 4 f rom the position in which your adapter was shipped.
Revision 1.7 Page 26 of 27 09/12/1999 W indows 95 START - Run regedit HKEY_LOCAL_MACHINE | |--S YS TEM | |--CurrentControlSet | |--S ervi ces | |--Cl ass | |--W inRT | |--W inRTdev0 | |--Parameter s |.
Ein wichtiger Punkt beim Kauf des Geräts Calibre UK IC Communication Adapter ICA93LV (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Calibre UK IC Communication Adapter ICA93LV noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Calibre UK IC Communication Adapter ICA93LV - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Calibre UK IC Communication Adapter ICA93LV reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Calibre UK IC Communication Adapter ICA93LV erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Calibre UK IC Communication Adapter ICA93LV besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Calibre UK IC Communication Adapter ICA93LV verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Calibre UK IC Communication Adapter ICA93LV. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Calibre UK IC Communication Adapter ICA93LV gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
