Benutzeranleitung / Produktwartung EMC39-12 des Produzenten Cabletron Systems
Zur Seite of 33
EMC39-12 12 POR T ETHERNET MEDIA CON VER TER USER’ S GUIDE EMC39-12 Ethernet Media Converter WITH LANVIEW TPLINK XMT RCV FOLNK 12 11 10 9 8 7 6 5 4 3 2 1 PWR 12 10 9 87 6543 21 RX TX RX TX RX TX RX .
.
EMC39-12 User’ s Guide iii NOTICE Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes ha ve been made.
Notice iv EMC39-12 User’ s Guide FCC NOTICE This device complies with P art 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this de vice must accept any interference receiv ed, including interference that may cause undesired operation.
Notice EMC39-12 User’ s Guide v CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT IMPORTANT: Before utilizing this product, carefully read this License Agreement.
Notice vi EMC39-12 User’ s Guide UNITED STATES GOVERNMENT RESTRICTED RIGHTS The enclosed product (a) was de veloped solely at pri vate expense; (b) contains “restricted computer software” submit.
EMC39-12 User’ s Guide v T ABLE OF CONTENTS CHAPTER 1 INTRODUCTION 1.1 Using This Manual ....................................................................... 1-1 1.2 Getting Help....................................................................
EMC39-12 User’ s Guide P age 1-1 CHAPTER 1 INTR ODUCTION W elcome to the Cabletron Systems EMC39-12 User’s Guide . This manual explains installation instructions and pro vides specifications for the twelve port Ethernet Media Con verter (EMC). 1.
Chapter 1: Introduction P age 1-2 EMC39-12 User’ s Guide 1.2 G ETTING HELP If you need additional support related to the EMC39-12, or if you hav e any questions, comments, or suggestions concerning this manual, contact Cabletron Systems T echnical Support: By phone (603) 332-9400 Monday-Friday; 8 A .
EMC39-12 Features EMC39-12 User’ s Guide P age 1-3 1.4 EMC39-12 FEATURES The EMC39-12 Ethernet Media Con v erter provides connecti vity for up to twelve singlemode fiber optic connections. The network connection is made through a 50-pin connector on the rear of the unit.
Chapter 1: Introduction P age 1-4 EMC39-12 User’ s Guide 1.5 EMC39-12 SPECIFICATIONS This section describes operating specifications for the EMC39-12. Cabletron Systems reserves the right to change these specifications at an y time without notice.
EMC39-12 User’ s Guide P age 2-1 CHAPTER 2 INSTALLATION This chapter explains ho w to install the EMC39-12 in a 19-inch rack and also provides requirements for installing the EMC39-12 on a tabletop or shelf. 2.1 UNPACKING THE EMC39-12 Unpack the EMC39-12 as follo ws: 1.
Chapter 2: Installation P age 2-2 EMC39-12 User’ s Guide 2.2.1 Rack Mounting the EMC39-12 Before installing the EMC39-12, care must be taken to ensure that the rack used will support the unit and that the rack remains stable with the EMC39-12 installed.
Installing The EMC39-12 EMC39-12 User’ s Guide P age 2-3 3. With the rack mounting brackets installed, position the EMC39-12 between the vertical frame members of the 19-inch rack and fasten it securely with the mounting screws as shown in Figure 2-2.
Chapter 2: Installation P age 2-4 EMC39-12 User’ s Guide 2.3 CONNECTING THE EMC39-12 T O THE PO WER SOURCE T o connect the EMC39-12 to the po wer source: 1. Plug the power cord into the back panel of the EMC39-12. 2. Plug the other end of the power cord into a grounded wall outlet.
EMC39-12 User’ s Guide P age 3-1 CHAPTER 3 CONNECTING T O THE NETW ORK This chapter outlines the procedure for connecting the EMC39-12 to your network. 3.1 CONNECTING A T WISTED PAIR SEGMENT T O THE EMC39-12 The rear panel of the EMC39-12 has a 50-pin Champ connector .
Chapter 3: Connecting T o The Network P age 3-2 EMC39-12 User’ s Guide T o connect the EMC39-12 to a 10B ASE-T compliant Ethernet device: 1. Attach a 50-pin feeder cable to the Champ connector on the EMC39-12 as shown in Figure 3-1. Figure 3-1 EMC39-12 2.
Connecting A Fiber Optic Link Segment EMC39-12 User’ s Guide P age 3-3 3.2 CONNECTING A FIBER OPTIC LINK SEGMENT When connecting a fiber optic link segment to the EMC39-12 k eep the follo wing in mind: • ST connectors attach to ST ports much like BNC connectors attach to BNC ports.
Chapter 3: Connecting T o The Network P age 3-4 EMC39-12 User’ s Guide T o connect a fiber optic link segment to the EMC39-12, perform the follo wing steps: 1. Remove the protective plastic covers from the fiber optic ports on the applicable port on the module and from the ends of the connectors on each fiber strand.
Finishing The Installation EMC39-12 User’ s Guide P age 3-5 3.3 FINISHING THE INSTALLATION The EMC39-12 is no w ready for operation. Before placing the network into service, test the installation thoroughly , making sure that you can address all stations and that the EMC39-12 and all stations are indicating normal operation.
EMC39-12 User’ s Guide P age 4-1 CHAPTER 4 USING THE LAN VIEW LED S This chapter describes ho w to use the LANVIEW Diagnostic LEDs to monitor EMC39-12 status and diagnose problems. Figure 4-1 LANVIEW LEDs 4.1 PWR (P ower) • On (Green) - Indicates that the EMC39-12 is recei ving po wer .
Chapter 4: Using The Lanview LEDs P age 4-2 EMC39-12 User’ s Guide 4.3 RCV (Receive) • On (Flashing Y ellow) - Indicates that the unit is recei ving data packets from the associated fiber optic port and transmitting them to the twisted pair port.
EMC39-12 User’ s Guide P age A-1 APPENDIX A CABLE REQUIREMENTS This appendix provides cable requirements for each of the EMC39-12 ports. A.1 10BASE-T T WISTED P AIR REQUIREMENTS When you connect a 10B ASE-T twisted pair segment to the EMC39-12, the de vice at the other end of the twisted pair segment must meet IEEE 802.
Appendix A: Cable Requirements P age A-2 EMC39-12 User’ s Guide Attenuation Y ou must test the fiber optic cable with a fiber optic attenuation test set adjusted for a 1300 nm wa velength. This test v erifies that the signal loss in a cable falls within the acceptable le v el of 10.
EMC39-12 User’ s Guide P age B-1 APPENDIX B T WISTED P AIR WIRING T ABLES This appendix contains twisted pair wiring tables which will assist you if you are using a Punch Do wn Block (see Figure B-1) to wire your twisted pair segments.
Appendix B: T wisted P air Wiring T ables P age B-2 EMC39-12 User’ s Guide TX-21 21 Blue/VioletTX- A42 Blue/Violet TX- RX+47 47 Violet/OrangeRX+ A43 Violet/Orange RX+ RX-22 22 Orange/VioletRX- A44 O.
T wisted Pair Wiring From An EMC39-12 T o a Punch Down Bloc k EMC39-12 User’ s Guide P age B-3 Po r t 6 Pin Pin Pin TX+36 36 Black/BlueTX+ A21 Black/BlueTX+ TX-11 11 Blue/Black TX- A22 Blue/Blac kTX.
Appendix B: T wisted P air Wiring T ables P age B-4 EMC39-12 User’ s Guide B.2 TWISTED P AIR WIRING FROM A PUNCH DO WN BLOCK T O A 10BASE-T DEVICE Pin Pin Pin TX+28 28 White/GreenTX+ A5 White/GreenT.
TWISTED P AIR WIRING FROM A PUNCH DO WN bLOCK T O A EMC39-12 User’ s Guide P age B-5 B43 Violet/OrangeTX+ 1 TX+ 1 TX+ 1 TX+ B44 Orange/VioletTX- 2 TX- 2 TX- 2 TX- P ort 10 Pin Pin Pin B37 Y ellow/Br.
Appendix B: T wisted P air Wiring T ables P age B-6 EMC39-12 User’ s Guide B28 Brown/BlackTX- 2 TX- 2 TX- 2 TX- P ort 6 Pin Pin Pin B21 Black/BlueRX+ 3 RX+ 3 RX+ 3 RX+ B22 Blue/Black RX- 6 RX- 6 RX-.
TWISTED P AIR WIRING FROM A PUNCH DO WN bLOCK T O A EMC39-12 User’ s Guide P age B-7 P ort 2 Pin Pin Pin B5 White/GreenRX+ 3 RX+ 3 RX+ 3 RX+ B6 Green/WhiteRX- 6 RX- 6 RX- 6 RX- B7 White/BrownTX+ 1 T.
Appendix B: T wisted P air Wiring T ables P age B-8 EMC39-12 User’ s Guide Figure B-1 Punch Down Bloc k Pins 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33.
POWER SUPPLY CORD The main cord used with this equipment must be a 2 conductor plus ground type with minimum 0.75 mm square conductors and must incorporate a standard IEC appliance coupler on one end .
Ein wichtiger Punkt beim Kauf des Geräts Cabletron Systems EMC39-12 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Cabletron Systems EMC39-12 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Cabletron Systems EMC39-12 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Cabletron Systems EMC39-12 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Cabletron Systems EMC39-12 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Cabletron Systems EMC39-12 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Cabletron Systems EMC39-12 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Cabletron Systems EMC39-12. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Cabletron Systems EMC39-12 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
