Benutzeranleitung / Produktwartung 00786976C des Produzenten Bush Hog
Zur Seite of 60
© 2010 Alamo Group Inc. $0.00 160 Series Published 08/10 Part No. 00786976C OPERA T OR’S MANUAL BUSH HOG ® 2501 Grif fin A ve. Selma, AL 36703 334-874-2700 www .bushhog.com REAR MOUNTED BLADE This Operator' s Manual is an integral p art of the safe operation of this machine and must be maintaine d with the un it at all times.
T o the Owner/Operator/Dealer All implements with moving p arts are potentially hazardous . There is no substitute for a cautious, safe-minded operator who recognizes the poten tial hazards and follows reasona ble safety practices.
T ABLE OF CONTENTS SAFETY SECTION ........ ................................. .................................................................. 1-1 Safety Messages ............... ................ ............. ................ ................. .....
Lubrication ................ ................ ............. ................ ................ ................ ................ ...... ................. ................ .. 5-2 Proper Torque For Fasteners ....................... ................... ..
Safety Section 1-1 SAFETY SECTION.
SAFETY 160 Series 08/10 Safety Section 1-2 © 2010 Alamo Group Inc. SAFETY Safety Messages A careful operator is the best opera tor . Safety is of primary importance to the manufacturer and should be to the owner/operator . Most accident s ca n be avo ided by bein g aware of your equipment, your surrounding s, and observing c ertain precautions .
SAFETY 160 Series 08/10 Safety Section 1- 3 © 2010 Alamo Group Inc. SAFETY Never operate the T ractor or Implement until you have read and completely underst and this Manual , the T ractor Operator ’s Ma nual, and each of the Safety Messages found in the Manual or on the Tr actor and Implement.
SAFETY 160 Series 08/10 Safety Section 1-4 © 2010 Alamo Group Inc. SAFETY Never allow children to operate, ride on, or co me close to the T ractor or Implement.
SAFETY 160 Series 08/10 Safety Section 1- 5 © 2010 Alamo Group Inc. SAFETY PROLONGED EXPOSURE TO LOUD NOISE MA Y CAUSE PERMANENT HEARING LOSS! T ractors with or without an Implement attached can often be noisy enoug h to cause permanent hearing loss.
SAFETY 160 Series 08/10 Safety Section 1-6 © 2010 Alamo Group Inc. SAFETY Periodically inspect all moving part s for wear and replace when necessary with au thorized service part s. Look for loose fastener s, worn or broken p arts, and le aky or loose fittings.
SAFETY 160 Series 08/10 Safety Section 1- 7 © 2010 Alamo Group Inc. SAFETY Operate the T ractor and/or Imp lement controls on ly while properly seated in the T ractor seat with the seat belt secure ly fastened around y ou. Inadvertent mo vement of the T ractor or Implement may ca use s eriou s inju ry or death.
SAFETY 160 Series 08/10 Safety Section 1-8 © 2010 Alamo Group Inc. SAFETY Rear Blades can fall down if not p roperly suppo rted. Always use the stand on the front hitch or block up securely to prev ent falling and possible crushing injury and/o r back injury from lifting heavy comp onents.
SAFETY 160 Series 08/10 Safety Section 1- 9 © 2010 Alamo Group Inc. SAFETY Decal Location NOTE: Bush Hog supplies safety decals on this product to promote safe op eration.
SAFETY 160 Series 08/10 Safety Section 1-10 © 2010 Alamo Group Inc. SAFETY ITEM P ART NO. QTY LEVEL DESCRIPTION 1. 00725746 1 PELIGRO T ranslate Safety Material 2. 02965262 1 W ARNING Oil Penetration 3. 00786980 1 IMPORT ANT Genuine Bush Hog Part s 4.
SAFETY 160 Series 08/10 Safety Section 1-11 © 2010 Alamo Group Inc. SAFETY Decal Description Peligro T ranslation, If you do not know how to read English, please find someone who knows how to read English.
SAFETY 160 Series 08/10 Safety Section 1-12 © 2010 Alamo Group Inc. SAFETY W ARNING!- Multiple H aza rd and Genera l Safety P/N 999200 Slow Moving V ehicle Decal.
SAFETY 160 Series 08/10 Safety Section 1-13 © 2010 Alamo Group Inc. SAFETY P/N 00786979 Logo Product Name: Bush Hog P/N 00786982 LOGO PRODUCT NAME: 160-08 P/N 00786989 LOGO PRODUCT NAME: 160-10 Red Reflector .
SAFETY 160 Series 08/10 Safety Section 1-14 © 2010 Alamo Group Inc. SAFETY Amber Reflector . Keep reflectors clean and visible. P/N 1458393 Read Operato r ’s Manual! The operator ’s ma nual is located inside this canister . If the manual is missing order one from you r dealer .
SAFETY 160 Series 08/10 Safety Section 1-15 © 2010 Alamo Group Inc. SAFETY Federal Laws and Re gulations This section is intended to explain in broad terms the conc ept and effect of federal laws and regulations concerning employer and employee eq uipment operators.
.
Introduction Section 2-1 INTRODUCTION SECTION.
INTRODUCTION 160 Series 08/10 Introduction Section 2-2 © 2010 Alamo Group Inc. INTRODUCTION This 160 Series Blade is designed with care and built with qualit y materials by skilled workers.
INTRODUCTION 160 Series 08/10 Introduction Section 2-3 © 2010 Alamo Group Inc. INTRODUCTION The 160 Series Blade is available in wid ths of 8' and 10' and features a hea vy-duty CA T II-III three-point hitch and quick-hitc h. The 10' model is ra ted for up to 160 PTO HP wheel-type tractors.
INTRODUCTION 160 Series 08/10 Introduction Section 2-4 © 2010 Alamo Group Inc. INTRODUCTION Attention Owner/Operator BEFORE OPERA TING THIS MACHINE: 1. Carefully read the Operator ’s Manual, completely underst and the Safety Messages and instructions, and know how to operate correctly both the tractor and implement.
Assembly Section 3-1 ASSEMBL Y SECTION.
ASSEMBLY 160 Series 08/10 Assembly Section 3-2 © 2010 Alamo Group In c. ASSEMBL Y Assembly of Moldbo ard to Mainframe The Bush Hog 160 Ser ies is shipped in two bu ndles. The Mainframe, A-Frame an d Moldboard Carrier are i n one bundle; the Moldbo ard is in the second bundle.
ASSEMBLY 160 Series 08/10 Assembly Section 3-3 © 2010 Alamo Group In c. ASSEMBL Y Attach Moldboard T ilt Cylinder with the Rod End attach ed to the Moldboard (Figure Asm-0 002) or optional Manual Adjusting links. Attach the Moldboa rd Pivot Cylinder as shown in Figure Asm-0003 or optional Manual Adjustin g Links.
ASSEMBLY 160 Series 08/10 Assembly Section 3-4 © 2010 Alamo Group In c. ASSEMBL Y Gauge Wheel (Extra Equipment) Mounting Holes have been provided for mountin g the Gauge Wheel to the Mainframe. Dual or Single Wheels with lam ina te d pu nc tu re pr oo f o r pn eu m at ic tires are optional.
ASSEMBLY 160 Series 08/10 Assembly Section 3-5 © 2010 Alamo Group In c. ASSEMBL Y Hydraulic Control V alv e (Extra Equipment) A 3 S pool 4 way Hydraulic Control V alve, open center or closed center , is available a s Accessory Equipment. This allows you to oper ate 4 Hydrau lic Cylinders from two remote ou tlets.
ASSEMBLY 160 Series 08/10 Assembly Section 3-6 © 2010 Alamo Group In c. ASSEMBL Y W r ist Pin & Bushing Arrangement.
Operation Section 4-1 OPERA TION SECTION.
OPERA TION 160 Series 08/10 Operation Section 4-2 © 2010 Alamo Group In c. OPERA TION BUSH HOG 160 SERIES REAR MOUNTED BLADE OPERA T ION INSTRUCTIONS Y our Bush Hog 160 Series should now be assembled and inspected for any evidence of defective or damaged part s before use.
OPERATION 160 Series 08/10 Operation Section 4-3 © 2010 Alamo Group In c. OPERA TION 1. S tandard Equipment and S pecifications Max. 2-Wheel Drive T ractor HP: (PTO) 8’ 190 HP (PTO) 10’ 160 HP Max.
OPERA TION 160 Series 08/10 Operation Section 4-4 © 2010 Alamo Group In c. OPERA TION 2. OPERA TOR REQUIREMENTS Safe operation of the unit is the responsibility of a qualifi ed operator .
OPERATION 160 Series 08/10 Operation Section 4-5 © 2010 Alamo Group In c. OPERA TION 3. TRACT OR REQUIREMENTS Operating the blade with a tractor th at does not meet the following requirement s may cause tractor or blade damage and be a potential danger to the operator and p assersby .
OPERA TION 160 Series 08/10 Operation Section 4-6 © 2010 Alamo Group In c. OPERA TION 3.3 T ractor 3-Point Hitch The tractor 3-point hitch must be ra ted to lift at least 1409 lbs. for the 8’ and 15 2 9 lbs. for th e 10 ’. The 160 Series can att ach to tractor’s with either a CA T II or III hitch.
OPERATION 160 Series 08/10 Operation Section 4-7 © 2010 Alamo Group In c. OPERA TION 4.1 Boarding the T r actor Use both hands and equippe d handrails and steps for supp ort when boarding the tractor . Never use control levers for support wh en mounting the tractor .
OPERA TION 160 Series 08/10 Operation Section 4-8 © 2010 Alamo Group In c. OPERA TION 5. ST ARTING THE TRACTOR The operat or must have a co mplete under standing of the placem ent, function , and operatio nal use of all tractor cont rols before starting th e tractor .
OPERATION 160 Series 08/10 Operation Section 4-9 © 2010 Alamo Group In c. OPERA TION 6.1 Connecting the Rear Blade 1. Shorten or remove the tra ctor drawba r to avoid interference when ra ising and lowering the rear blade. 2. Board the t ra cto r an d s tart t he en g i ne.
OPERA TION 160 Series 08/10 Operation Section 4-10 © 2010 Alamo Group In c. OPERA TION 7. PRE-OPERA TION INSPECTION AND SERVICE Before each use, a pre- operation inspection and service of the implement and tractor must be perform ed.
OPERATION 160 Series 08/10 Operation Section 4-11 © 2010 Alamo Group In c. OPERA TION 7.2 Blade Pre-Operation Inspection/Service Before each blade u se, a comp lete inspectio n and service is re quired to en sure the b lade is in a good and safe working condition.
OPERA TION 160 Series 08/10 Operation Section 4-12 © 2010 Alamo Group In c. OPERA TION T r actor PRE-OPERA TIO N Inspection T ractor ID#:___________ _____________Make:________________________ Date:__.
OPERATION 160 Series 08/10 Operation Section 4-13 © 2010 Alamo Group In c. OPERA TION Blade & Box Blade PRE- OPERA TION Inspection Blade ID#:_______________________Make:__________________________.
OPERA TION 160 Series 08/10 Operation Section 4-14 © 2010 Alamo Group In c. OPERA TION 8. DRIVING THE TRACTOR AND IMPLEMENT Safe tractor transport requ ires the operator possess a thoro ugh knowledge of the mode l being operated and precautions to t ake while driving with an att ached implem ent.
OPERATION 160 Series 08/10 Operation Section 4-15 © 2010 Alamo Group In c. OPERA TION 8.1 St arting the T ractor The procedure to st art the tractor is model specific. Refer to the tractor operator’s manual for st arting procedures for your p articular tractor .
OPERA TION 160 Series 08/10 Operation Section 4-16 © 2010 Alamo Group In c. OPERA TION 8.3 Driving the T ractor and Blade S tart o ff driving at a slow spee d and gradually increase your speed while m aintaining complete control of the tractor and blad e.
OPERATION 160 Series 08/10 Operation Section 4-17 © 2010 Alamo Group In c. OPERA TION 9.1 Operating the Blade Only operate the blade from the tractor ope rator’s seat with the seatbelt securely fastened. The tractor must be equipped with a ROPS in the raised position or a ROPS cab.
OPERA TION 160 Series 08/10 Operation Section 4-18 © 2010 Alamo Group In c. OPERA TION 9.2 Shutting Down the Implement Park the tractor on a leve l surface, place the transmission in park or neu tral.
OPERATION 160 Series 08/10 Operation Section 4-19 © 2010 Alamo Group In c. OPERA TION When transporting, only raise the blade enough to clear ground obst acles to prevent tipping, especially when traveling throug h ro u gh terr a in.
OPERA TION 160 Series 08/10 Operation Section 4-20 © 2010 Alamo Group In c. OPERA TION Before transp orting the tractor on a public r oadway or boarding a trailer for tran sport, the tract or brake pedals should be lo cked together .
OPERATION 160 Series 08/10 Operation Section 4-21 © 2010 Alamo Group In c. OPERA TION The SMV (Slow-Moving V ehicle) emblem is universal symbol used to aler t drivers of the presence of equipm ent traveling on roadways at a slow speed. SMV signs are a triangular br ight orange with r eflective r ed trim f or both ea sy day an d night visibility .
OPERA TION 160 Series 08/10 Operation Section 4-22 © 2010 Alamo Group In c. OPERA TION Reduce speed before tur ning or ap plying th e brake s. Ensure that both brake pedals ar e locked together when operating on public roads.
OPERATION 160 Series 08/10 Operation Section 4-23 © 2010 Alamo Group In c. OPERA TION Arrange the cha ins so that when tightened, the chains are pulling downward and against themselves. Ca refully tighten the securing chain s or other fasteners using boomers or binders to apply maximum tension.
OPERA TION 160 Series 08/10 Operation Section 4-24 © 2010 Alamo Group In c. OPERA TION 13. T roubleshooting Guide Problem Pos sible Cause Remedy Shearing M/B Carrier Lack of lu brication Lubricate Pi.
Maintenanc e Sec tio n 5- 1 MAINTENANCE SECTION.
MAINTENANCE 160 Series 08/10 Maintenance Section 5-2 © 2010 Alamo Group Inc. MAINTENANCE Lubrication The Bush Hog 16 0 Series is a rugged , dependable Blade that should pe rform satisfactorily with t.
MAINTENANCE 160 Series 08/10 Maintenance Section 5-3 © 2010 Alamo Group Inc. MAINTENANCE Proper T orque For Fasteners The chart lists the correct tightening to rque for fastener s.
BUSH HOG LIMITED W ARRANTY 1. LIMITED W ARRANTIES 1.01. Bush Hog warrants for one year from the purchase date to t he original non-commercial, govern mental, or municipal purchaser (“Purchaser”) a.
T O THE OWNER/OPERA T OR/DEALER T o keep your implement running ef ficiently and safe ly , read your manual thoroughly and follow th ese directions and the Safety Messages in this Manual. T he T able of Contents clearly identi fies each section where you ca n easily find the informa tio n yo u ne ed .
160 SERIES - SOM-08/10 P/N 00786976C Printed U.S.A 160 SERIES REAR MOUNTED BLADE.
Ein wichtiger Punkt beim Kauf des Geräts Bush Hog 00786976C (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Bush Hog 00786976C noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Bush Hog 00786976C - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Bush Hog 00786976C reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Bush Hog 00786976C erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Bush Hog 00786976C besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Bush Hog 00786976C verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Bush Hog 00786976C. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Bush Hog 00786976C gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
