Benutzeranleitung / Produktwartung FM01FD00B des Produzenten Burnham
Zur Seite of 108
101786-01R5-1 1/10 Price - $5.00 n o n o i t a m r o f n i g n i k e e s n e h W . r o t c a r t n o c g n i t a e h r u o y l l a c , r e l i o b o t s r i a p e r r o e c i v r e s r o F .
2 EQUIPMENT CHECK LIST This Equipment Check List has been provided so that the Installer can determine if all parts have been provided for the boiler ordered. It covers standard equipment for Knockdown boilers, 4 thru 18 section models. Optional equipment ordered will be in addition to, or in lieu of, equipment shown below .
3 KNOCKDOWN BOILER - EQUIPMENT CHECK LIST (Continued) Component Description Carton Designation on Bar Code Label Part Number Qty . Req’d. Per Boiler Size 4 Sect. 5 Sect. 6 Sect. 7 Sect. 8 Sect. 9 Sect. 10 Sect. 1 1 Sect. 12 Sect. 13 Sect. 14 Sect. 15 Sect.
4 KNOCKDOWN BOILER - EQUIPMENT CHECK LIST (Continued) Component Description Carton Designation on Bar Code Label Part Number Qty . Req’d. Per Boiler Size 4 Sect. 5 Sect. 6 Sect. 7 Sect. 8 Sect. 9 Sect. 10 Sect. 1 1 Sect. 12 Sect. 13 Sect. 14 Sect. 15 Sect.
5 IMPOR T ANT INFORMA TION - DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death, serious injury or substantial property damage.
6 DANGER DO NOT store or use gasoline or other ammable vapors or liquids in the vicinity of this or any other appliance. W ARNING Improper installation, adjustment, alteration, service or maintenance can cause property damage, personal injury or loss of life.
7 W ARNING Appliance materials of construction, products of combustion and the fuel contain alumina, silica, heavy metals, carbon monoxide, nitrogen oxides, aldehydes and/or other toxic or harmful sub.
8 T ABLE OF CONTENTS SECTION I - GENERAL INFORMA TION Dimensional Information ................................................................................................................. 10 Ratings/Data ...........................................
9 T ABLE OF CONTENTS (continued) SECTION VI - SERVICE INSTRUCTIONS Cleaning Boiler Heating Surfaces .................................................................................................... 68 Maintenance of Low W ater Cutoff Devices ......
10 Figure 1b: Dimensional Information * Wiring harness shown in this location for illustration purposes - typically , wiring harness leads will exit jacket on same side as BSD hinges.
1 1 SECTION I - GENERAL INFORMA TION Boiler Model Number of Sections Dim. A (Inches) * Burner Dimension B (Inches) Minimum Flue Bafe Installation Clearance Dim. C (Inches) V ent (Flue Outlet Damper) Connection Size Dim. D (Inches) Approx. Weight of Sections - LBS.
12 Model MPC™ Boilers Boiler Model Boiler Horsepower Burner Input Gross Output (MBH) Net I=B=R Rating (MBH) Combustion Efciency Heating Surface (Sq. Ft.) Net Furnace V olume (Cu. Ft.) Pressure in Firebox (Inches Wtr . Column) W ater Content (Gallons) Boiler Weight w/W ater (LBS.
13 SECTION I - GENERAL INFORMA TION (Continued) INSPECT SHIPMENT carefully for any signs of damage. 1. ALL EQUIPMENT is carefully manufactured, inspected and packed. Our responsibility ceases upon delivery of crated Boiler to the carrier in good condition.
14 T able V : Minimum Installation Clearances T o Combustible Materials (Inches) per UL726 (Packaged / Firetested Boiler) C A B Chimney D E F Boiler Above Front Connector Rear Sides Below MPC 18 48 18 18 18 NC * * NC - Noncombustible Flooring Note: See T able III for recommended service clearance to access rear of boiler .
15 a. In the absence of local requirements, the conned space shall be provided with two permanent openings, one in or near the top of the room and one near the bottom. The openings shall communicate by means of ducts, with the outdoors or to such spaces (crawl or attic) that communicate with the outdoors.
16 Figure 3b: V ents - Faults and Suggestions W ARNING V enting Instructions are recommendations only . Consult a venting expert on the design of a specic vent system for your application. The ASHRAE V enting Guide and The National Fuel Gas Code, NFP A 54 should be considered in all venting systems.
17 F ACTOR Y ASSEMBLED SECTIONS - The assemblage should be set in the proper location as outlined in Section I. Lifting arrangement and weights are given in Figures 4a and 4b.
18 Then proceed to Step C of this section on Page 24, “HYDROST A TIC TEST”. FIELD ASSEMBLED SECTIONS - If the boiler was ordered knockdown, to be eld assembled, follow the assembly procedure outlined on the following pages.
19 Figure 5: Manual or Hydraulic Draw-up Section Assembly.
20 Figure 6: V ertical Bracing of Rear Section Figure 8: Inspection Pad Locations for Section Draw-up Figure 7: Setting of Nipples.
21 W ARNING This is a forced draft red boiler and sealant must be applied where specied for proper and safe performance. Burnham Commercial has approved section joint sealants (silastics) manufactured by Dow-Corning under the product number RTV 736, and Sil-Bond under the product number RTV 6500.
22 adjacent sections as the boiler operates with a positive pressure in the rebox and products of combustion will escape between sections unless they are properly sealed. The rope and sealant should be applied before each section is placed on the assembly .
23 2. ASSEMBL Y OF SECTIONS • MPC4 through MPC12 Section Assemblies The entire assemblage may be drawn-up at one time using the hydr.
24 After all sections have been drawn up, retention rods must be installed. Do not release hydraulic pressure until the retention rods are in place. Locate the threaded 5/8” retention rods, washers, tension springs and nuts supplied in ‘BAC’ Boiler Assembly Carton.
25 SECTION III - BOILER ASSEMBL Y INSTRUCTIONS (Knockdown Boiler) Figure 9: Installation of Common Parts to Block Assembly.
26 INST ALL COMMON P AR TS T O BLOCK ASSEMBL Y , Refer to Figure 9. 1. Remove contents from Common Parts Carton marked ‘CPC’. 2. Locate four (4) C. I. burner swing door (BSD) hinge/latch castings, two (2) C. I. BSD hinge loop castings, ten (10) 7/16 split lock washers and ten (10) 7/16 -14 x 1-1/2 lg.
27 f. Install observation port sight glass. Locate 2” x 2-1/2” lg. nipple, sight glass envelope and 2” conduit bushing. Thread 2” nipple into observation port tapping directly above burner adapter opening on front of BSD. Open sight glass envelope and in this order place gasket, sight glass and gasket into conduit cap.
28 T able VII: Modular Return W ater Mixing T ube (RWMT RC).
29 Figure 13: Return W ater Mixing T ube RC Assembly and Installation.
30 Repeat this process for each joint, securing the previous assembly to the tube shown in next column to the right in T able VII, also refer to Figure 13 for details.
31 5. Add front/center section mounting hardware to all but one (1) horizontal support channel assembly . Lay channel assembly on oor with brackets facing up, see Figure 17a.
32 Figure 17a: Front/Center Section Horizontal Channel Assembly w/Mounting Hardware Figure 17b: Rear Section Horizontal Channel Assembly w/Mounting Hardware.
33 Figure 18a: Mount Front/Center Section Horizontal Channel to Block Assembly Figure 18b: Mount Rear Section Horizontal Channel to Block Assembly.
34 Figure 19: Attachment of Lower Front/Center Section Bracket to Casting Leg Figure 20: Attachment of Lower Rear Section Bracket to Casting Leg.
35 Hand tighten one (1) 5/8” washer and hex nut on bolt. Do not wrench tighten at this time. Repeat for all brackets, both sides. 1 1. Locate and install rear section brackets to casting legs. Brackets are universal and can be used on either side of block assembly .
36 Figure 22: Lower Tie Bar Installation Repeat operation until all vertical channels have been installed. Using an open end wrench and ratchet with socket, tighten all 5/8” bolts and nuts to secure frame brackets to casting legs. 13. Locate Jacket Carton(s), marked ‘JC-2’ and remove contents.
37 Locate and Install Heat Exchanger (Block Assembly) Insulation W rapper(s), see Figure 23. 1. - Insulation wrapper is provided as one-piece that covers block from front to rear .
38 Installing Internal W iring Harness for Control/Safety Circuits - refer to Figures 24a through 24g. 1. See Figure 24a for layout of Internal wiring harness components.
39 3. Locate chaseway channel(s) shipped in Jacket Carton marked ‘JC-2’, see Figures 24c and 24d. Identify main chaseway channel by it’ s unequal ends. Install the end with 8¼” lg. side ange under horizontal rail and through openings in junction box until end protrudes past rear horizontal channel.
40 Figure 24e: Internal Wiring Harness Components - Install Protective Edging Install 1-13/16” lg. pieces on horizontal raw edges at both ends of chaseway channel assembly . Install 4-1 1/16” lg. pieces to vertical chaseway channel anges inside primary junction box as shown in Figure 24e.
41 Figure 24g: Internal Wiring Harness Components - Secure Harness to V ertical Channel Insert rst set of harness connectors through opening in rear of secondary junction box. Remove excess slack between J-boxes until protective sleeve is centered on raw edge of channel extension, secure harness to channel using nylon wire tie No.
42 c. BSD with right hand hinge arrangement - harness exits right side of jacket front panel en route to control panel. d. BSD with right hand hinge arrangement - harness exits left side of jacket front panel en route to control panel.
43 T able X: Jacket T op Corner / Intermediate Panel Arrangement Boiler Size Side of Boiler Order of Assembly (* See Panel Designation Below) Front f Block Assembly g Rear 4 Section Left 27” TCP w/J.
44 On 12 thru 18 Section Boilers, locate top intermediate panel(s) #3 per T able X and secure to panel #1 and each other using two (2) #8 x ½” lg. hex head SMS per joint. Align mounting holes in panel(s) #3 with holes in frame rails and secure with two (2) #8 x ½” lg.
45 Figure 28: Jacket Split Rear Panel Detail Figure 29: Install Jacket Split Rear Panel Locate Jacket Split Rear Panel shipped in JC-1 Jacket Carton. Note: Before installing rear panel, drain valve and indirect water heater return piping (furnished by others) should be installed now due to accessibility .
46 Position front panel at approximately 30° angle, hook front ange under clips on outer top corner panels as shown in Figure 30a, Detail A, Step 1.
47 Install Burner Swing Door (BSD) on Block Assembly hinges, see Figure 31. Move BSD to front of boiler . Position door on the Floor , standing up, perpendicular to front of boiler (full open position).
48 Important Produc t Safety Informati on Refractory Ceram ic Fiber Product Warning : The Repair Parts list designates parts that contain refractory ceramic fibers (RCF).
49 Figure 33: Install 2 nd Pass Flueway Bafes Figure 32: Install 3 rd Pass Flueway Bafes (4 thru 1 1 Section Boilers Only) 2. On 4 thru 18 Section Boilers - Install four (4) second pass bafes into second pass ueways until handle is ush with face of casting as shown in Figure 33, Detail A.
50 Close Burner Swing Door and secure using (4) 5/8” at washers, (4) 9/16” lock washers and (4) 9/16 - 12 x 2” lg. cap screws as shown in Figure 34. There are (4) points of internal contact around perimeter of BSD and Front Section. These stop the door travel when tightening hardware to prevent excess compression of rope gasket.
51 1. In most cases the burner adapter plate carton for the specied burner will be provided by Burnham. 2. If adapter is provided by Burnham, open carton and remove contents. Apply four (4) small dabs of silastic on rear surface of adapter plate to temporarily hold gasket in place.
52 1. Harness is split into two (2) 7 wire bundles that exit side of front panel as shown in Figure 25. 2. Each seven (7) wire harness bundle must be encased in exible conduit from cover plate to burner control panel or junction box. 3. Locate front panel cover plates in JC-1 carton.
53 Note: Supply manifold must be installed with 1½” couplings aligned with front and rear axis of boiler . 2. Apply thread sealant and install temperature/ pressure gauge into tapping ‘G’, see Figures 38 and 39. W rench until water tight. T ighten gauge using hex on stem, do not tighten or apply pressure to case.
54 Installing Optional Controls (if applicable): 1. Install M&M 750P-MT -120 Probe Low W ater Cut Off (L WCO) a. Apply thread sealant to ¾” probe and install in T apping ‘E’, see Figure 38. W rench hex until water tight. b. Remove 2 nd knockout from bottom of M&M 750P L WCO control case.
55 c. Connect opposite end of L4006B Low Fire Hold Control harness to right side junction box cover ‘A ’, hole location #2 as shown in Figure 40. d. Locate mating connector labeled “Low Fire Hold” inside right junction box. Join mating connectors which are polarized and lock together .
56 v . Connect opposite end of T991A Modulating Control harness to right side junction box cover ‘A ’, hole location #4 as shown in Figure 40. vi. Locate mating connector labeled “LO-HI- LO/MOD” inside right junction box, see Figure 40. Join mating connectors which are polarized and lock together .
57 Install Optional Split Jacket Panels for Burner Swing Door (BSD) Cover (if applicable). 1. Open carton and remove contents. 2. Locate hanger bracket for BSD cover , secure to jacket front panel with three (3) #8 x 1/2” hex head SMS as shown in Figure 47.
58 SECTION IV - INST ALLA TION INSTRUCTIONS Packaged Boiler Shipping Information Figure 48: Packaged Boiler Shipping Information 1. The packaged boiler comes on its own shipping skid (see Figure 48) and the assembled block is hydrostatically tested at the factory .
59 Figure 49a: Recommended MPC Minimum Piping - Single Boiler Application NOTES: 1. All piping is schedule 40. 2. Pipe sizes listed are based on a 20°F or 40°F Delta T (temperature rise across the boiler).
60 .
61 Figure 50a: Alternate MPC Minimum Piping - Single Boiler Application Boiler Model Supply / Return 20°F Rise 40°F Rise Nom. I.D. (Inch) W ater Side Press. Drop (Ft/Wtr) Flow Rate (GPM) Nom. I.D. (Inch) W ater Side Press. Drop (Ft/Wtr) Flow Rate (GPM) MPC4 2 1.
62 .
63 a. T emperature and Flow Requirements – An existing parallel piping system may be used, provided the return water is not below 80°F and the return water temperature is not more than 80°F less than the boiler outlet temperature.
64 – The MPC boiler can be used in many different piping applications to produce Domestic Hot W ater (DHW).
65 SECTION V - OPERA TING INSTRUCTIONS 1.
66 W ARNING Before installation of the boiler is considered complete, the operation of the boiler controls should be checked, particularly the low water cutoff and the high limit control. 1. CHECK OPERA TING CONTROL OPERA TION.
67 The pH should be higher than 7 but lower than 1 1. Add some appropriate water treatment chemicals, if necessary , to bring the pH within the specied range. W ith this lower level of protection, care must be exercised to eliminate all of the free oxygen in the system.
68 SECTION VI - SER VICE INSTRUCTIONS IMPOR T ANT - See Section V , Item (G) under Operating Instructions, if it becomes necessary to add water to the boiler more frequently than once a month. - Inspection should be conducted annually .
69 f. Use a wire or ber bristle brush of appropriate length and diameter to allow sufcient cleaning of all ue passages. Using long strokes, push the brush the whole way through the boiler and then pull it out. Repeat this process until all surfaces of each of the ue passages have been cleared of all soot and debris.
70 W ARNING Exercise caution when handling phosphoric acid and follow the instructions on container label. Always use protective clothing and equipment when working with/near chemicals. i. W ire brushing of the probe is not recommended as the soft platinum guard ring sandwiched between the ceramic insulators may be damaged.
71 T able XII: Recommended Periodic T esting Check List Item Frequency Accomplished by Remarks Gauges and Indicators Daily Operator Make visual inspection and record readings in log Instrument and Equ.
72 T able XII: Recommended Periodic T esting Check List (continued) Item Frequency Accomplished by Remarks High Limit Safety Control Annually Service T echnician Refer to instructions Operating Contro.
73 SECTION VII - BURNER SPECIFICA TIONS BOILER MODEL BURNER MIN. INPUT (GPH) BURNER MAX. INPUT (GPH) BURNER MODEL AIR TUBE COMB. BURNER SETTINGS PUMP PRESSURE (PSI) NOZZ LE MAKE NOZZLE DA T A HE AD LOW FIRE AIR OR SHUTTER HIGH FIRE AIR OR BAND LOW FIRE HIGH FIRE GPH X ANGLE - TYPE MPC4 1.
74 BOILER MODEL BURNER MIN. INPUT (GPH) BURNER MAX. INPUT (GPH) BURNER MODEL DIFFUSER OPENING (IN.) APPROX. HIGH FIRE DAMPER SETTING - TOP / BOTTOM DAMPER (IN.) HIGH FIRE PUMP PRES SURE (PSI) NOZZLE MAKE NOZZLE DA T A GPH X ANGLE - TYPE MPC4 3.0 3.55 C1-O 3/16 5/16 / Closed 300 Delavan 2.
75 BOILER MODEL BURNER INPUT ** BURNER MODEL DIFFUSER OPENING (IN.) APPROX. HIGH FIRE DAMPER SETTING - TOP / BOTTOM DAMPER (IN.) APPROX. NA T . GAS MANIFOLD PRESS. A T ORIFICE TEE (“WC) MINIMUM NA T . GAS INLET PRESS. (“WC) *** GAS (MBH) OIL (GPH) MPC4 500 3.
76 SECTION VIII - REP AIR P ARTS All MPC™ Repair Parts may be obtained through your local Burnham Commercial Cast Iron Wholesale distributor . Should you require assistance in locating a Burnham Com.
77 Item No. Description Boiler Sections / Quantity Part No. 04 05 06 07 08 09 10 1 1 12 13 14 15 16 17 18 1 MPC-R Rear Section (Machined) 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 100658-01 2 MPC-C Center Section.
78 Figure 56: MPC Common Bare Boiler Components.
79 REP AIR P ARTS - COMMON BARE BOILER COMPONENTS Item No. Description Boiler Sections / Quantity Part No. 04 05 06 07 08 09 10 1 1 12 13 14 15 16 17 18 1 4” NPT CI Supply Manifold 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 706MPC401 2 4” NPT CI Return Manifold 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 706MPC402 3 5/8” x 158” Lg.
80 Figure 56: MPC Common Bare Boiler Components (continued).
81 Item No. Description Boiler Sections / Quantity Part No. 04 05 06 07 08 09 10 1 1 12 13 14 15 16 17 18 20 9/16” Split-Lock W asher , Plated 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 101760-01 20A 5/8” Flat W asher 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 80860608 21 9/16” -12 x 2” Lg.
82 Figure 57: MPC Front & Center Section Frame Rail Assembly.
83 Item No. Description Boiler Sections / Quantity Part No. 04 05 06 07 08 09 10 1 1 12 13 14 15 16 17 18 1 Jacket Frame-Horizontal Support Channel 1 1 1 2 2 2 2 2 3 3 3 3 3 4 4 100758-01 2 Jacket Frame-Horizontal Support Channel Bracket 2 2 2 4 4 4 4 4 6 6 6 6 6 8 8 100757-01 3 #8 x 1/2” Lg.
84 Figure 58: MPC Rear Section Frame Rail Assembly.
85 Item No. Description Boiler Sections / Quantity Part No. 04 05 06 07 08 09 10 1 1 12 13 14 15 16 17 18 1 Jacket Frame-Horizontal Support Channel 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 100758-01 2 Jacket Frame-Horizontal Support Channel Bracket 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 100757-01 3 #8 x 1/2” Lg.
86 Figure 59: MPC Return W ater Mixing T ube RC Assembly.
87 REP AIR P ARTS - RETURN W A TER MIXING TUBE RC ASSEMBL Y Boiler Model Return W ater Mixing T ube Assembly , Flared Collar Return Water Mixing T ube Assembly , Square End T otal T ubes Required 1027.
88 Figure 60: MPC Heat Exchanger Insulation Wrapper.
89 Item No. Description Boiler Sections / Quantity Part No. 04 05 06 07 08 09 10 1 1 12 13 14 15 16 17 18 1 Complete Heat Exchanger Wrapper Insulation 1A. 4” Thk Nominal x 32-5/8” x 140-3/4” Lg. 1 101835-04 1B. 4” Thk Nominal x 39-3/8” x 140-3/4” Lg.
90 Figure 61: MPC Internal Wiring Harness Components.
91 Item No. Description Boiler Sections / Quantity Part No. 04 05 06 07 08 09 10 1 1 12 13 14 15 16 17 18 1 Primary Internal J-Box 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 101418-01 2 Secondary Internal J-Box Assy . w/Securing Channel 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 101533-01 3 #8 x 1/2” Lg.
92 Figure 62: MPC Jacket Panel Assembly.
93 REP AIR P ARTS - JACKET P ANEL ASSEMBL Y Item No. Description Boiler Sections / Quantity Part No. 04 05 06 07 08 09 10 1 1 12 13 14 15 16 17 18 1 Jacket Front Panel 11111111111111 1 1 0 0 7 5 3 - 0 1 2 Jacket Front Panel Wiring Harness Cover Plate 22222222222222 2 1 0 1 4 2 2 - 0 1 3 #8 x 2-1/2” Lg.
94 Figure 62: MPC Jacket Panel Assembly (continued).
95 REP AIR P ARTS - JACKET P ANEL ASSEMBL Y (continued) Item No. Description Boiler Sections / Quantity Part No. 04 05 06 07 08 09 10 1 1 12 13 14 15 16 17 18 1 1 Jacket Rear T op Panel 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 100735-01 12 Internal J-Box Cover Plate 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 101 190-01 13 7/8” Dia.
96 Figure 63: MPC 2 nd and 3 rd Pass Flueway Bafes.
97 Item No. Description Boiler Sections / Quantity Part No. 04 05 06 07 08 09 10 1 1 12 13 14 15 16 17 18 1 2 nd Pass Flueway Bafes, 304 Stainless Steel: 1A. 18” 2P Bafe Assembly w/Handles 4 101647-01 1B. 24¾” 2P Bafe Assembly w/Handles 4 101647-02 1C.
98 Figure 64: MPC Standard 50 PSI T rim & Control with 30 PSI and 80 PSI Working Pressure T rim Options.
99 REP AIR P ARTS - ST ANDARD W A TER TRIM & CONTROL AND OPTIONAL WORKING PRESSURE TRIM Item No. Description Boiler Sections / Quantity Part No. 04 05 06 07 08 09 10 1 1 12 13 14 15 16 17 18 10 Op.
100 Figure 64: MPC Standard 50 PSI T rim and Control with 30 PSI and 80 PSI Working Pressure T rim Options (continued).
101 REP AIR P ARTS - ST ANDARD W A TER TRIM & CONTROL AND OPTIONAL WORKING PRESSURE TRIM (continued) Item No. Description Boiler Sections / Quantity Part No. 04 05 06 07 08 09 10 1 1 12 13 14 15 16 17 18 OPTIONAL WORKING PRESSURE TRIM: 51 Relief V alve, 30 PSI: 51A.
102 Figure 65: MPC Optional Controls.
103 REP AIR P ARTS - COMMON OPTIONAL CONTROLS Item No. Description Boiler Sections / Quantity Part No. 04 05 06 07 08 09 10 1 1 12 13 14 15 16 17 18 1 Probe Low Water Cut-Of f: 1A. L WCO, McDonnell & Miller 750 P-MT -120 w/Probe 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 80160718 1B.
104 Figure Number Page Number Description Equipment Check List Figure 1a 2 Carton Identication Section I - General Information Figure .
105 Figure Number Page Number Description Section III - Boiler Assembly Instructions (Knockdown Boiler) (continued) Figure 25 42 Internal Wiring Harness - Length Adjustment for Penetration Through Sid.
106 Figure Number Page Number Description Section VIII - Repair Parts Figure 55 76 MPC Cast Iron Section Assembly Description 77 Cast Iron Section Assembly Figure 56 78 MPC Common Bare Boiler Componen.
107 T able Number Page Number Description Section I - General Information T able I 1 1 Dimensional Information T able II 12 Ratings/Data T a.
108 Subject to the terms and conditions set fort h below, Burnham Commercial, Lancaster , Pennsylvania hereby extends the following limited wa rranties to the original ow ner of a commercial grade wat.
Ein wichtiger Punkt beim Kauf des Geräts Burnham FM01FD00B (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Burnham FM01FD00B noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Burnham FM01FD00B - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Burnham FM01FD00B reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Burnham FM01FD00B erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Burnham FM01FD00B besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Burnham FM01FD00B verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Burnham FM01FD00B. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Burnham FM01FD00B gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
