Benutzeranleitung / Produktwartung TWIN APS des Produzenten Bunn
Zur Seite of 32
CDBC TWIN, TWIN APS CA U T IO N :.
Page 2 INTRODUCTION This equipment will brew one or two half-gallon batches of coffee simultaneously into awaiting dispensers with just the press of a button. One side may include a hot water faucet for allied beverage use. Most functions of the brewer are digitally controlled.
Page 3 USER NOTICES Carefully read and follow all notices in this manual and on the equipment. All labels on the equipment should be kept in good condition. Replace any unreadable or damaged labels. # 00986.0000 # 03408.0002 # 03409.0002 # 00656.0000 # 00658.
Page 4 ELECTRICAL REQUIREMENTS CAUTION - The brewer must be disconnected from the power source until specified in Initial Set-Up. Electrical Hook-Up CAUTION – Improper electrical installation will damage electronic components. 1. An electrician must provide electrical service as specified.
Page 5 OPERA TING CONTROLS Model CDBC TWIN ON/OFF SWITCH Pressing the "ON/OFF" switch (indicator glowing) supplies power to the brew station warmer, enables the brew circuit, and energizes the tank refill circuit. Pressing the switch again (indicator not glowing) stops tank refilling, brewing and deenergizes the brew station warmer.
Page 6 INITIAL SET -UP 1. Insert an empty funnel into the funnel rails of one of the brew stations. 2. Place an empty decanter/server under the funnel. 3. Connect the brewer to the power source. 4. Press the "ON/OFF" switch (indicator glowing).
Page 7 ADJUSTMENTS & OPTIONAL SETTINGS HIDDEN SWITCH.
Page 8 ADJUSTING BREW VOLUMES The brewer is factory set to deliver 64 ounces ± 2 for each brew cycle. BREW VOLUME SET-UP: Use the following steps when the setting is unknown or a different circuit board is being installed. 1. Place an empty funnel in the funnel rails and an empty decanter/server or graduated vessel beneath the funnel.
Page 9 PULSE BREW SETUP PROCEDURE The pulse brew parameters (initial fill time, off times, and remaining on times) are entered using the following set- by-example process. 1. First set the brew volume using the standard procedure in Brew Volume Setup.
Page 10 TROUBLESHOOTING A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic Technical Service Department.
Page 11 Will not fill or refill Fill or refill does not shut "OFF" (ON/OFF Switch "ON") PROBABLE CAUSE REMEDY PROBLEM 1. Power off to brewer 2. Water shut off 3. Display flashing 4. ON/OFF Switch 5. Lime build up on Probe 6. Refill Valve or Control Board 7.
Page 12 Fill or refill does not shut "OFF" (ON/OFF Switch "OFF") 2. Water Level Probe Sensing Sys- tem 3. Refill valve or control board 4. Water is too conductive for proper operation when using the factory setting of sensing threshold.
Page 13 TROUBLESHOOTING (cont.) PROBABLE CAUSE REMEDY HEATING CIRCUIT PROBLEM 1. Display flashing 2. Water not touching tempera- ture probe 3. Dry Plug In Probe Sensing Sys- tem Brewer has shut down due to malfunction (See Diagnostic Chart in manual, Page 20, or under top lid).
Page 14 TROUBLESHOOTING (cont.) Water does not heat to proper temperature (cont.) IMPORTANT: Make sure no tem- perature tests are taken before the ready light is "ON". Tank tempera- ture must be stabilized before read- ings are taken. Spitting or excessive steaming 4.
Page 15 TROUBLESHOOTING (cont.) Spitting or excessive steaming (cont.) Brewer is making unusual noises 2. Temperature Probe 3. Control Board 1. Plumbing lines 2. Water supply 3. Lime build up Remove the probe from the grom- met and submerge in a water bath of approximately 70 ° F(21 ° C).
Page 16 TROUBLESHOOTING (cont.) PROBABLE CAUSE REMEDY BREWING CIRCUIT PROBLEM Brew cycle will not start 1. Display flashing 2. No water 3. No power or incorrect voltage to the brewer 4. ON/OFF switch not in the "ON" position 5. Low water temperature (Brew lockout is enabled) 6.
Page 17 Brew cycle will not start (cont.) Consistently low beverage level in the dispenser or beverage over- flows dispenser TROUBLESHOOTING (cont.) PROBABLE CAUSE REMEDY If the switch panel is operating properly, proceed as follows. At- tach a voltmeter to the terminals of the dispense solenoid.
Page 18 TROUBLESHOOTING (cont.) Dripping from sprayhead Weak beverage 1. Lime build up 2. Dispense valve 1. Sprayhead 2. Water temperature 3. Filter type 4. Coffee grind 5. Funnel loading Inspect the tank assembly for ex- cessive lime deposits. Delime as required.
Page 19 TROUBLESHOOTING (cont.) Dry coffee grounds remain in the funnel Low beverage serving tempera- ture 1. Sprayhead 2. Funnel loading 1. Warmer Make sure sprayhead is present and holes are clear and unob- structed. There should be sepa- rate streams of water coming out of each hole in the sprayhead.
Page 20 DIAGNOSTICS Intermittent flashing of the bank of temperature indicators indicates that a fault exists. Count the number of flashes between pauses and use this chart as a guide to investigating the fault.
Page 21.
Page 22 CAUTION :.
Page 23 CAUTION : CAUTION : CAUTION : CAUTION DISCARD DECANTER IF: . CRA CKED . SCRATCHED . BOILED DRY . HE ATED WHEN EMP TY . USED ON HIGH FLAM E . OR EXPOSED ELECTRIC E LE MENTS FAILURE TO COMPLY RI.
Page 24 CAUTION : CAUTION DISCARD DECANTER IF: . CRAC KED . S CRATCHED . BOILED DRY . HEATED WHEN E MPTY . USED ON HIG H FLAME . OR EXPOS ED ELE CTRIC ELEMENTS FAILURE TO COMPLY RISKS INJURY PN: 658 1985 BU N N-O-M ATIC CO RPORATION FUNNEL CONTENTS ARE HO T ! SERVICE (cont.
Page 25.
Page 26 Location: The tank heaters are located inside the tanks and secured to the tank bottoms. Test Procedures: 1. Disconnect the brewer from the power supply. 2. With a voltmeter, check the voltage across the red wire from the terminal block and the black wire from the control board.
Page 27 P1856 SERVICE (cont.) TANK HEATERS (Cont.) 17. Install tank assembly onto mounting brackets and secure in place with four #8-32 nuts. 18. Install tank lid and secure in place with eight #8-32 nuts. 19. Connect the two white wires of the tank warmer blanket.
Page 28 CAUTION : CAUTION : C.
Page 29 C A U T IO N : C A U T IO N : C A U T IO N :.
Page 30 36672 030104 SCHEMATIC WIRING DIAGRAM CDBC TWIN 0/6 (LEFT) 29323.0000C 02/04 ©1999 BUNN-O-MATIC CORPORATION TANK HEATER GRN GRN RED-14 (MODEL 35) BLK BLK-14 SCHEMATIC WIRING DIAGRAM CDBC TWIN.
Page 31 36672 030104 SCHEMATIC WIRING DIAGRAM CDBC TWIN 2/2 (LEFT) 29323.0002B 02/04 ©2000 BUNN-O-MATIC CORPORATION TANK HEATER GRN GRN RED-14 (MODEL 35) BLK BLK-14 SCHEMATIC WIRING DIAGRAM CDBC TWIN.
Page 32 SCHEMATIC WIRING DIAGRAM CDBC TWIN APS (LEFT) 32161.0000B 8/99 ©1999 BUNN-O-MATIC CORPORATION TANK HEATER GRN GRN RED-14 (MODEL 35) BLK BLK-14 SCHEMATIC WIRING DIAGRAM CDBC TWIN APS (RIGHT) W.
Ein wichtiger Punkt beim Kauf des Geräts Bunn TWIN APS (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Bunn TWIN APS noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Bunn TWIN APS - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Bunn TWIN APS reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Bunn TWIN APS erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Bunn TWIN APS besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Bunn TWIN APS verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Bunn TWIN APS. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Bunn TWIN APS gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
