Benutzeranleitung / Produktwartung Harrier 41 des Produzenten Briggs & Stratton
Zur Seite of 36
(Auto Drive) (English V ersion) FROM SERIAL NO: 410A001001, 41 1A001001, 412A001001 HANDBOOK: 410066 (REV .2.) ISSUE 08.07.02 CODE 410A . 41 1A . 412A (Electric Start V ariable Speed) OWNER'S HAN.
Engine Briggs & Stratton Quantum XTS 45 Engine type 12F802-1325-01 (410) 12F802-1325-01 (41 1) 12F807-1324-01 (412) Engine/Cutterbar speed 3000 rpm Fuel type Unleaded petrol Fuel capacity 1.
1.19 - 1.25 Mower Maintenance 1.19 - Engine 1.19 - Thr ottle Cable Adjustment 1.19 - Carbur ettor Adjustments 1.20 - Oil Service 1.20 - Air Cleaner Service 1.21 - Spark Plug Service 1.21 - Keeping Engine Clean 1.21 - Grassbag 1.22 - Deck Housing 1.22 - Securing Nuts and Bolts 1.
INTRODUCTION 1.4 Thank you for purchasing a Hayter mower . The following pages are designed to help you gain safe and efficient service from your mower . IMPOR T ANT : This ‘Owners Handbook’ should be regarded as part of the mower as it gives essential information regarding mower safety , operation, maintenance and specifications.
W ARRANTY 1.5 LIMITED WARRANTY Hayter Limited warrants to the original user/purchaser that this unit shall be free from defects in material and workmanship under normal use and service for a period of three years from the date of purchase.
SAFETY PRECAUTIONS 1.6 This safety alert symbol indicates important safety messages. When you see this symbol be alert to the possibility of injury . Carefully r ead the following and inform others. Y our mower is perfectly safe if used correctly . Failur e to observe the following precautions may r esult in serious injury .
PRECAUTIONS SAFETY 1.7 - Always use fresh fuel. Stale fuel can block the carburettor and cause leakage. - Replace fuel tank and oil tank caps securely . A damaged cutterblade or loose fixing bolt are major hazards. Before use, always visually inspect the cutting mechanism to ensure that it is in good condition.
Do not tilt the mower when starting the engine. Do not put hands or feet near or under rotating parts. Never pick up or carry the mower while the engine is running. Never lift the rear deflector while the engine is running. Never touch the exhaust/exhaust guard or cooling fins when the engine is hot.
SAFETY PRECAUTIONS 1.9 Allow the engine to cool before storing in any enclosure. T o reduce the fire hazard, keep the engine and the surrounding deck area free of grass, leaves, or excessive grease. Check the rear deflector and grassbag frequently for wear or deterioration.
ASSEMBLING THE MOWER 1.10 Remove the mower from the packaging and check that the following items have been supplied correctly . If any items are missing contact, your local Hayter dealer . 1. Engine Handbook. 2. W arranty Reg. Card. 3. Grassbag. 4. Charger (412) 5.
MOWER THE ST AR TING 1.11 T o prevent engine damage the engine is shipped without oil or petrol. The engine must be filled with the correct grade of oil and petrol befor e starting the engine. Always use high quality detergent oil classified SAE 30 oil.
Controls Operate all control levers several times and ensure that the cables move freely . Check that the engine stop and ground drive clutch levers return freely to their rest position when released. Whilst operating the engine throttle mechanism slight resistance should be felt when moving the lever to the ‘ choke ’ position.
MOWER THE OPERA TING 1.13 (412 Only) - Stand behind the mower and hold the handlebar together with the engine stop lever . T urn the ignition key in a clockwise direc- tion and hold in position to crank the engine. When the engine starts release the key and move the throttle to the fast position after starting a cold engine.
1.14 T o prevent engine damage do not use the mower on slopes greater than 20 degrees. Move the height of cut lever sideways to disengage it from the locking notch, then push forwards to lower or pull backwards to raise the height of cut.
1.15 Remove the grassbag and operate the mower with the rear deflector in the closed position. Areas of heavy growth should be mown without collecting the clip- pings. If collection is required, first mow the area without the grass- bag at the maximum height of cut setting.
1.16 There is very little work to do this month apart from brushing away leaves. Keep off the grass if frozen or waterlogged. Rake the grass thoroughly . Spike the lawn to aerate and stimulate soil organisms and root growth and apply lawn sand if necessary .
1.17 Keep mowing regularly and watering as necessary . Fill any cracks caused by drought with a mixture of sharp sand and soil. In dry weath- er conditions leave the grass longer to help retain ground moisture. Raise the height of cut to allow the grass to thicken and protect the roots from the winter frost and snow .
1.18 After the very first hour check clutch adjustment. See page 1.22. After the very first five hours change the engine oil. Follow the hourly or calendar intervals, whichever occurs first.
1.19 T o prevent accidents stop the engine disconnect the spark plug lead before attempting to carry out maintenance pr ocedures on the mower . 1. Air Filter 2.
1.20 Check the oil level daily before starting the engine and ensure that the correct oil level is maintained. Refer to-‘Before Starting the Mower ’ for oil checking and filling instructions. Change the engine oil after the first 5 hours of operation and thereafter according to the ‘Maintenance Schedule’:- 1.
1.21 B R I G GS & S T R A T T O N HA R R IE R 41 Use only Briggs & Stratton spark tester (1) to check for a spark as shown in the diagram. Replace the spark plug every 100 hours or every season, whichever occurs first. A spark plug wrench is available from any authorised Briggs & Stratton service dealer .
1.22 Remove grass debris from the top and underside of the deck housing immediately after use. Fertilisers and top dressings ar e particularly corrosive. Thoroughly clean the mower deck immediately after use on tr eat- ed grass and store well away fr om corrosive materials.
1.23 Lubricate the wheels, pivot points and linkages with engine oil every 25 operating hours. Apply a good quality medium grease to the inner control cables at the point of entry and exit from their outer casing. Drain the fuel by running the engine until the fuel tank is empty and the engine stops.
1.24 Assemble the cutterblade with the turned up edges facing towards the engine. Secure the cutterblade using the bolt (1), spring washer (2), and distance piece (3) and tighten to a torque of 54Nm A slightly worn cutterblade may be re-sharpened. Both blade edges must be sharpened equally to ensure balance.
1.25 BR IGGS & ST R AT T O N H A R R I E R 4 1 Storage T o store the handlebar unscrew the 2 small securing knobs sufficient- ly to allow it to be pivoted forwards to rest against the mower .
MOWER MAINTENANCE (412 only) - PREVENT ACCIDENTS: AL W A YS charge the bat- tery in a well ventilated area. NEVER charge the battery near naked flames or direct heat. AL W A YS switch off the mains electricity supply before discon- necting the charger from the battery .
1.27 PROBLEM POSSIBLE F AUL T REMEDY Engine will not turn over Engine stop lever released. Operate engine stop lever . Incorrect oil level. Check oil level. Obstruction under deck. Remove obstruction. Battery discharged (412 Only) Charge battery Engine smokes Excess oil level.
1.28 PROBLEM POSSIBLE F AUL T REMEDY Engine vibrates excessively Mounting bolts loose. T ighten bolts Cutterblade bolt loose. T ighten bolt Cutterblade out of balance.
CONFORMITY OF DECLARA TION 1.29 VIBRA TION INFORMA TION Lawnmower vibration information. RMS acceleration measured in 3 - axes at operators contact position on the handlebars.
1.30 PA R T S LIST ITEM NO. 1 Mainframe 410010V 1 1 1 2 Cover- Side RH 410033 1 1 1 3 Screw - T aptite M6x16 09365 33 32 32 4 Rod - Deflector 305103 1 1 1 5 Key - W oodruff 1662 1 1 1 6 Decal - Grass .
1.31 LIST PA R T S ITEM NO. 39 Fabric - Grassbag 410039 1 1 1 40 Deflector - Rear 410028 1 1 1 41 Bolt - Coach M8x40 09379 2 2 2 42 Plug - Drive Small 300144 4 4 2 43 Ratchet - HOC 410006 1 1 1 44 Dec.
1.32 PA R T S LIST ITEM NO. 79 Cover - Side LH 410032 1 1 1 80 Lever - HOC 480128 1 1 1 81 Spring - HOC 480132 1 1 1 82 Screw - T aptite M6x35 09786 2 2 2 83 Frame - Roller W/A 41001 1W 1 1 1 84 Shell.
11 8 71 70 11 8 1 2 3 3 3 4 5 6 9 10 13 14 17 17 19 18 20 25 23 28 29 30 34 33 31 38 39 11 12 41 3 3 3 79 47 49 68 76 78 80 81 91 91 83 84 3 97 95 101 100 99 102 103 104 108 105 106 107 BRI G G S &.
41 1A/412A PA R T S LIST 1.34 1 2 3 3 3 4 5 6 9 10 13 14 17 36 17 19 18 21 20 25 23 28 29 30 34 33 31 32 35 38 39 11 12 111 41 3 3 3 79 47 50 49 51 55 59 61 58 67 68 69 70 71 75 76 63 64 78 80 81 91 9.
/NOTES Mower Serial No:................................................................................. Engine Model:.................................. T ype:....................................... Code:..................................... Notes: 1.
We hope you find the links below useful. For further ga rdening information visit Gardening Tools Direct Blower Vacs Brush cutters Brushcutters Chainsaws Chain saws Cultivators Cylinder lawn mowers Cy.
Ein wichtiger Punkt beim Kauf des Geräts Briggs & Stratton Harrier 41 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Briggs & Stratton Harrier 41 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Briggs & Stratton Harrier 41 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Briggs & Stratton Harrier 41 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Briggs & Stratton Harrier 41 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Briggs & Stratton Harrier 41 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Briggs & Stratton Harrier 41 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Briggs & Stratton Harrier 41. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Briggs & Stratton Harrier 41 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
