Benutzeranleitung / Produktwartung ACCESSORY MODULE Including Protection, Performance, and Inlet Shut-off Valve Packages des Produzenten Bradford-White Corp
Zur Seite of 76
238-47878-00 B 04/10 ACCESSORY MODULE Including Protection, Performance, and Inlet Shut-off Valve Packages INSTALLATION & OPERATION MANUAL With Troubleshooting Guide PLACE THESE INSTRUCTIONS ADJAC.
Important Information -2- Accessory Module: The Accessory Module is an electronic component that allows the water heater gas control to be connected to the Protection, Performance, and Inlet Shut-off Valve Packages.
Important Information -3- Protection Package (sold separately): Contains: o Leak sensor (2 piece) o Dam o Leak sensor wire harness o Wire holders o Wire ties o Screws Features: o Senses a collection o.
Important Information -4- CAUTION The water heater, when se t at a lower temperature setting, is not capabl e of producing hot water of sufficient temperature for sanitizing purposes. NOTICE The water heater is equipped with an energy cu t out device to prevent overheating.
Important Information -5- For energy efficient operation of your water h eater, the suggested initial water temperatu re setting is 120 ˚ F (49 ˚ C). During the winter season, or any col d peri od, you may desire a higher water temperature setting to adjust for the colder incoming water.
Table of Contents -6- Page Tools Required ............................................................................................ 7 Package Components ................................................................................. 8 Accessory Module .
Tools Required -7- Slotted Screwdriver Philips Screwdriver 1/8” Drill bit Drill Needle nose pliers Pipe dope Adjustable wrench Caulk gun RTV sealant (silicone) Pipe cutter Propane torch Solder Flux .
Package Components Accessory Module -8- Table 1 Accessory Module Description Quantity 1A Plug-in Transformer 1 2A WV4460 Wire Harness 1 3A Transformer Wire Harness 1 4A WV8840 Wire Harness 1 5A Wire H.
Package Components Protection Package -9- Table 2 Protection Package Description Quantity 1B Leak Sensor Bracket 1 2B Leak Sensor Housing 1 3B Dam 1 4B Screws 6 5B Leak Sensor Wire Harness 1 6B Wire H.
Package Components Performance Package -10- Table 3 Performance Package Description Quantity 1C Setback Control Wire Harness 1 2C Integrated Mixing Device, IMD 1 - Cold Water Tee - Mixing Valve - 8”.
Package Components Inlet Shut-off Valve Package -11- Table 4 Inlet Shut-off Valve Description Quantity 1D Inlet Shut-off Valve with Integrated Wire Harness 1 2D ¾” x 1” NPT Brass Bushings 2 3D Wi.
Wiring Diagram -12-.
Accessory Module Installation -13- In the following section, the instructions detail how to inst all the Accessory Module. Properly locating and mounting the Accessory Module is required. Unpack the Accesso ry Module Step 1: Remove the Accessory Module and its comp onent s from their packaging, as shown in Figure 1.
Accessory Module Installation -14- Determine the Gas Control Wire Harness – cont’d Step 3: If the gas control uses a standing pilot, the WV8840 wire harness must be u sed. The WV8840 gas control and wire harness a re shown in Figure 3. Discard the WV4460 wi re harness.
Accessory Module Installation -15- Mark the Location of the Acce ssory Module Step 5: Using a marker, mark the location of the Accessory Module screw holes. This is shown in Figure 5. Set the Accessory Module Aside Step 6: Remove the Accessory Module from t he water heater jacket, as sho wn i n Figure 6.
Accessory Module Installation -16- Drill the Accessory Module Scre w Holes Step 7: Using a 1/ 8” drill bit and drill, drill the (2) scre w holes that were marke d in Step 5. This is sho wn in Figure 7. Position the Accessory Module Step 8: Put the Accessory Module up again st the water heater jacket and posi tion it to the pre-drilled holes.
Accessory Module Installation -17- Mounting the Accessory Module Step 9: Using (2) of the i ncluded Philips head screws, screw the Accessory Module to th e water heater jacket, as shown in Figure 9. Apply the Necessary Labels Step 10: Apply both the wiring diagram and diagnost ic labels.
Accessory Module Installation -18- Remove the Accessory Module Cover Step 11: Using a Philips head screwdriver, loosen both screws on the A ccessory Module cover, as shown in Figure 11. The cover screws are p ermanently retained and cannot be comple tely removed.
Accessory Module Installation -19- Transformer wire ha rness Assemble the Transformer and its Wi re Harness Step 13: Take one end of the transformer wire ha rnes s and slide each fork terminal un der one of the screws.
Accessory Module Installation -20- Prepare to Connect the Transformer Wire Harness to the Acc essory Module Step 15: Loosen the (2) Philips h ead screws on the Accessory Module, labeled “R1” and “C1.
Accessory Module Installation -21- Connect the Transformer Wire Harness and the Accessory Module Step 17: Tighten both screws, “R1” and “C1,” while holding the Transformer wire harness in place, as shown in Figure 17.
Accessory Module Installation -22- Assemble the WV4460 Wire Harness and Accessory Module Step 19: Insert the red wire, from the WV4460 wire ha rness, under the screw la beled “D/1.” This is shown in Figure 19. Connect the WV4460 Wir e Harness and Accessor y Module Step 20: Tighten the screw labeled “D/1,” as shown in Figure 20.
Accessory Module Installation -23- Assemble the WV4460 Wire Harness and Accessory Module – cont’d Step 21: Insert the black wire, from the WV4460 wire harne ss, under the screw labeled “R/2.
Accessory Module Installation -24- Assemble the WV4460 Wire Harness and Accessory Module – cont’d Step 23: Insert the white wire, from the WV4460 wire harne ss, under the screw labeled “C/3.
Accessory Module Installation -25- Connect the Accesso ry Module to the WV8840 Wire Harness Step 25: Insert one end of the WV8 840 wire harness ov er the edg e of the Accessory Module circuit board. This connection point is o n the bottom right hand side of the circuit board, and it is shown in Figure 25.
Accessory Module Installation -26- Connect the WV8840 Wir e Harness to the WV8840 Gas Con trol Step 27: Push the plastic connector o n the WV8840 wire harness into th e recessed area on the botto m side of the WV8840 gas control. This is shown in Figure 27.
Setback Control Installation -27- In the following section, the instructions detail how to install the Setback Control on the water heater. The Accessory Module must be installed for the Setback Control to work with the water heater gas control.
Setback Control Installation -28- Remove the Setback Con trol Battery Holder Step 3: Depress the top side of the battery holder and remove it. This is sho wn in Figure 30. Install the Setback Contr ol Batteries Step 4: Install the (2) supplied AAA ba tteries into the battery holder of the Setback Control, as shown in Figure 31.
Setback Control Installation -29- Install the Setback Contr ol Battery Holder Step 5: Install the Setback Control Batt ery Holder, just as it was installed prior t o Step 3. This is shown i n Figure 32. Remove the Protectiv e Plate Step 6: Remove the Setback Control protective plat e from the Setback Control by pullin g these items apart.
Setback Control Installation -30- Locate the Setback Contr ol Junction Box Assembly Step 7: Place the Setback Control Junction Box Assembly on top of the water heater. This a s sembly mu st face the front of the water heater, an d it must be located close to the centerlin e of the water heater.
Setback Control Installation -31- Remove the Setback Con trol Junction Box Assembly Step 9: Remove the Setback Control Junctio n Box Assembly from the top of the water heat er, as shown in Figure 36.
Setback Control Installation -32- Position the Setback Control Junc tion Box Assembly Step 11: Put the Setback Control Jun ction Box Assembly back on top of the wa ter heater and position it to the pre-drilled holes.
Setback Control Installation -33- Install the Setback Contr ol Step 13: Snap the Setback Control into the backpla te on the Setback Control Jun ction Box Assembly. Align the Setback Control to the backplate, and press until it is fully seated. This is shown in Figure 40.
Setback Control Installation -34- Connect the Setback Co ntrol Wire Harness to the Accessory Module Step 15: If the water heater gas control has a n inte rmittent pilot (WV4460 gas control), the conne ction, “D/1,” is already being used. This same conne ction point is used to connect the Setback Control.
Setback Control Installation -35- Connect the Setback Co ntrol Wire Harness and Accessory Module Step 17: Tighten the screw labeled “D/1,” as shown in Figure 44.
Setback Control Installation -36- Assemble the Setback Control Wire Harn ess and Accessory Module – cont’d Step 19: Insert the black wire, from the Setback Control wire harness, under the scre w labeled “R/2.” If the water heater has a WV4460 gas control, the gas c ontrol wire harness bl ack wire must be retained underneath this screw also.
Setback Control Installation -37- Assemble the Setback Control Wire Harn ess and Accessory Module – cont’d Step 21: If the water heater gas control has a n inte rmittent pilot (WV4460 gas control), the conne ction, “C/3,” is already being used.
Setback Control Installation -38- Connect the Setback Co ntrol Wire Harness and Accessory Module – cont’d Step 23: Tighten the screw labeled “C/3,” as sho wn in Figure 50. The Setback Control installation is complete. Proceed to the installation sections for the other purch ased packages.
Integrated Mixing Device - IMD -39- Refer to the instructions included with Integrated Mixing Device (IMD), on how to install and operate the IMD. Figure 51 shows the contents included with the integra ted mixing device. Figure 51 CAUTION The piping diagram suppli ed with the water heater must be followed.
Leak Sensor Installation -40- In the following section, the instructions detail how to install the Leak Sensor. The Accessory Module must be installed for the Leak Sensor to work with the water heater gas control. The leak sensor can take up to 15 minutes to sense and verify a water heater tank leak.
Leak Sensor Installation -41- Connect the Leak Sensor and its Wire Harness Step 3: Connect the Leak Sensor wire harness to the Lea k Sensor (specifically the end wi th the plastic connector), as shown in Figure 54. Prepare the Accessory Module for the Leak Sensor Step 4: Loosen the screw labeled “C1,” as shown in Fi gure 55.
Leak Sensor Installation -42- Prepare the Accessory Module for the Leak Sensor – cont’d Step 5: Loosen the screw labeled “LK,” as sho wn in Figure 56. Remove the Leak Sensor Resistor Step 6: Using needle nose pliers, remove the Lea k Sensor resistor fro m the Accessory Module and discard.
Leak Sensor Installation -43- Assemble the Leak Sensor Wire Harness and the Accessory Module Step 7: Insert the red wire, from the Leak S ensor wire harness, unde r the screw labeled “C1.” This i s shown in Figure 58. En sure that the wire from the Transfo rmer wire harness at this loca tion is retained under this screw.
Leak Sensor Installation -44- Assemble the Leak Sensor Wire Harness and the Accessory Module – cont’d Step 9: Insert the black wire, from the Leak Sensor wire ha rness, under the screw labeled “LK.
Leak Sensor Installation -45- Position the Leak Sensor Step 11: Position the Leak Sensor up against the water heater jacket, as shown in Figu re 62. The Leak Sensor must be positioned to the left of the water heat er gas control. The Leak Sensor must sit flat on the floor or in the drain pan.
Leak Sensor Installation -46- Remove the Leak Sensor Step 13: Remove the Leak Sensor f rom the water heater jacke t, and set it a side. This is shown in Figure 64. Drill the Leak Sensor Mounting Hole Step 14: Using a 1/8” drill bit and drill, drill the screw hole that was ma rked in Step 12.
Leak Sensor Installation -47- Position the Leak Sensor Step 15: Put the Leak Sensor back in position against th e water h eater jacket and position to the pre- drilled hole, as shown in Figure 66. Mount the Leak Sensor Step 16: Using (1) of the included P hilips head screws, screw the Leak Sensor to the water heater jacket.
Leak Sensor Installation -48- Position the Dam Step 17: Position the dam aro und the water heater, so it surrounds th e water heater and corrals a water heater tank leak towards the Leak Senso r. This is shown in Figure 68. Fill in the Gaps Step 18: Fill in any gaps between the dam and the floor.
Inlet Shut-off Valve Installation -49- In the following section, the instructions detail how to install the Inlet Shut-off Valve. If installed, this device will shut off the water supply to the water heater after the Leak Senso r has sensed and verified a water heater tank leak has occu rred.
Inlet Shut-off Valve Installation -50- Determine if Bushings are Necess ary Step 3: If the water heater u ses a 3/4” NPT thread water inlet, the (2) in cluded 3/4” x 1” NPT bushings must be used.
Inlet Shut-off Valve Installation -51- Install the Bushings Step 5: Thread the bushings into each end of the Inlet Shut-off Valve, as shown in Figure 72. Install the Inlet Shut-off Valve Step 6: Thread the Inlet Shut-off Valve onto the wate r heater inlet (cold).
Inlet Shut-off Valve Installation -52- Connect the Cold Water Supply Step 7: Pipe the cold water supply piping to the Inlet Shut-off Valve inlet, as shown in Figure 74. Connect the Inlet Shut-off Valv e Harness to the Accessory Module Step 8: Loosen the (3) screws on the Accessory Module lab eled “C2,” “NO,” and “N C.
Inlet Shut-off Valve Installation -53- Assemble the Inlet Shut-off Valve Wire Harn ess and the Accessory Module Step 9: Insert the blue wire, from the Inlet Shut-off Valv e wire harness, under t he screw labeled “C2,” as shown in Figure 76.
Inlet Shut-off Valve Installation -54- Assemble the Inlet Shut-off Valve Wire Harn ess and the Accessory Module – cont’d Step 11: Insert the brown wire, from the Inlet Shut-off Valve wire harn ess, under the screw labeled “NO,” as shown in Figure 78.
Inlet Shut-off Valve Installation -55- Assemble the Inlet Shut-off Valve Wire Harn ess and the Accessory Module – cont’d Step 13: Insert the black wire, from the Inlet Shut-off Va lve wire harness, under the screw la beled “NC,” as shown in Figure 80.
Remote Mounting th e Setback Control -56- In the following section, the instructions detail how to Remote Mount the Setback Control. Remove the Setback Con trol from the Backplate Step 1: Remove the Setback Co ntrol from the back plate attach ed to the Setback Control Junction Box Assembly.
Remote Mounting th e Setback Control -57- Mount the Protective Plate Step 3: Mount the Setback Control Protective Plate in a de sired location. Be sure that the Setback Control will not be direct sunlight, as the display may be difficult to read. This is shown in Figure 84.
Remote Mounting th e Setback Control -58- Label the Wires for Rem ote Mounting Step 5: Label the (3) cut wires (A), (B ), and (C) respectively. Label both en ds of the wires.
Remote Mounting th e Setback Control -59- Install Wire (A) – Backplate Step 7: Using wire (A), insert one end into the top terminal locat ion on the backplate (located on the Setback Control Junctio n Box Assembly). This is s hown in Figure 88. Be sure that the wire already located in this location is not dislodged.
Remote Mounting th e Setback Control -60- Install Wire (B) – Backplate Step 9: Using wire (B), insert one end into the mi ddl e terminal location on the backplate (l ocated on the Setback Control Junctio n Box Assembly). This is s hown in Figure 90.
Remote Mounting th e Setback Control -61- Install Wire (C) – Backplate Step 11: Using wire (C), insert one end into the bot tom terminal location on th e backplate (located on the Setback Control Juncti on Box Assembly). This is shown in Figure 92. Be sure that the wire already located in this location is not dislodged.
Remote Mounting th e Setback Control -62- Route Wires to Protectiv e Plate Step 13: Route all three wires to t he Setback Control Protective Plate. Install Wire (A) – Protective Plate Step 14: Using wire (A), insert on e end into the top terminal location on the Protective Plate.
Remote Mounting th e Setback Control -63- Fasten Wire (A) into its Designa ted Location – Protec tive Plate Step 15: Tighten the slotted screw in the top terminal lo cation on the Protective Plate.
Remote Mounting th e Setback Control -64- Fasten Wire (B) into its Designa ted Location – Protec tive Plate Step 17: Tighten the slott ed screw in the middle terminal location on the Protective Plate.
Remote Mounting th e Setback Control -65- Fasten Wire (C) into its Designa ted Location – Protec tive Plate Step 19: Tighten the slotted screw in the bottom terminal location on the Protective Plate. This is shown in Figure 99. Install Setback Control Step 20: Snap the Setback Control into the Protective Plate.
Remote Mounting th e Setback Control -66- Install Cover Plate Step 21: Snap the Setback Cover Plate onto the back plate (located on the Setback Control Junction Box Assembly). This is shown in Figure 101. Figure 101 Remote Mounting the S etback Control is compl ete.
Start-up Procedure -67- In the following section, the instructions deta il the Start-up Procedure for the Accessory Module, once any or all of its packages are completely installed. Route the Wire Harn ess es in the Accessory Module Step 1: Route all of the wire harnes ses out of the openi ngs in the bottom and left side of the Acce ssory Module.
Start-up Procedure -68- Fix the Accessory Module Cov er in Place Step 3: Tighten both Accessory Module co ver screws, as sho wn in Figure 104. Route the Various Wire Harnesses Step 4: Route the wire ha rnesses along the jacket and group th em using the included wire ties.
Start-up Procedure -69- Fix the Wire Harnesses Step 5: Using the include d wire holders, fix the wi re harn esses to the water heater jacket only to the left of the water heater gas cont rol, as shown in Figure 106. Wire holders can be use d to fix the wire harnesses to the water heater jacket only to the left of the water heater gas control.
Start-up Procedure -70- Plug in Transformer Step 7: Plug in the Transformer that powers the A ccessory Module, as well as its components. This is shown in Figure 108. Observe Accessory Module Start-up Sequence Step 8: Watch the LED on the Accessory M odule, and observe as it prog resses through the Start-up Sequence.
Start-up Procedure -71- Action Required for Improper Start-u p Sequence Step 9: If the Start-up Sequence results in a red LE D strobe, the internal ele ctronics on the Accessory Module failed. The Accessory Modul e must be repl ac ed. This is shown in Figure 110.
Start-up Procedure -72- Verify Inlet Shut-off Valve Operation (if installed) Step 11: If the Inlet Shut-off Valve is installed, t he valve will open during the Start-up Sequence. Verify that the valve is open by drawing water from a faucet (s pecifically hot water).
Diagnostic Codes -73- LED Status Accessory Module Status Probable Cause None No LED. Power not on. 1. No power at outlet. 2. Transformer bad, replace transformer. 3. Transformer wire ha rne ss not properly connected. Check all wire connectio ns. Green LED on continuously.
Notes -74-.
LIMITED PARTS WARRANTY -75- WHAT DOES THIS LIMITED WARRAN TY COVER? This limited warranty covers compon ent parts for malfunction caused by defects in materials and/or workmanship. It extends to the first buyer and to any subsequent owner(s) at the original pl ace of installation.
Ambler, PA For U.S. and Canada field service, contact your professional installer or local Bradford White sa les representative. Sales / 800-523-2931 Fax / 215-641-1670 Parts Fax / 215-641-2108 Techni.
Ein wichtiger Punkt beim Kauf des Geräts Bradford-White Corp ACCESSORY MODULE Including Protection, Performance, and Inlet Shut-off Valve Packages (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Bradford-White Corp ACCESSORY MODULE Including Protection, Performance, and Inlet Shut-off Valve Packages noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Bradford-White Corp ACCESSORY MODULE Including Protection, Performance, and Inlet Shut-off Valve Packages - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Bradford-White Corp ACCESSORY MODULE Including Protection, Performance, and Inlet Shut-off Valve Packages reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Bradford-White Corp ACCESSORY MODULE Including Protection, Performance, and Inlet Shut-off Valve Packages erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Bradford-White Corp ACCESSORY MODULE Including Protection, Performance, and Inlet Shut-off Valve Packages besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Bradford-White Corp ACCESSORY MODULE Including Protection, Performance, and Inlet Shut-off Valve Packages verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Bradford-White Corp ACCESSORY MODULE Including Protection, Performance, and Inlet Shut-off Valve Packages. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Bradford-White Corp ACCESSORY MODULE Including Protection, Performance, and Inlet Shut-off Valve Packages gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
