Benutzeranleitung / Produktwartung KLT-12G des Produzenten Blodgett
Zur Seite of 23
1 IMPORTANT NOTES FOR INSTALLATION AND OPERATION KLT-12G GAS FIRED FLOOR MODEL TILTING KETTLE INSTALLATION – OPERATION – MAINTENANCE BLODGETT OVEN COMPANY www.
2 It is recommended that this manual be read thoroughly and that all instructions be followed carefully. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
3 TABLE OF CONTENTS DESCRIPTION PAGE 1.0 IMPORTANT NOTES FOR INSTALLATION AND OPERATI ON ........................... 2 2.0 SERVICE CONNECTIONS ................................................................................... 4 3.0 INTRODUCTION .....
4 2.0 SERVICE CONNECTIONS 3 [76] 4.75 [121] 23.75 [603] 25.388 [645] 17.25 [438] 5.5 [140 ] 1 1.25 [2 86] 15 [381] 7.75 [197] MIN. 6 [152] 12.50 [317] POUR P A TH 6 [152] 23.88 [607] 32.88 [835] 55.75 [1416] 30 [762] Ø16.75 [425] I.D. Ø20 [508] 15.88 [403] FLANGED FOOT DETAIL 4 7/16" [1 1mm] HOLES ON 3 [76] B.
5 3.0 INTRODUCTION DESCRIPTION Model KLT-12G (12 gallon capacity) gas fired, self -contained, tilting kettle. The kettle has a jacket of double-wall construction forming a sealed reservoir around the lower two-thirds of the kettle. The reservoir is charged with distilled water.
6 4.0 INSTALLATION INSTRUCTIONS GENERAL Gas installation to conform to local codes or in absence of local codes to the National Fuel Gas Code - ANSI Z223.1 - latest edition. In Canada, installation to be according to CAN/CGA- B149.1 (NAT) or CAN/CGA-B149.
7 GAS CONNECTION 1. The Serial and Rating Plate on the unit indicates the type of gas your unit is equipped to burn. DO NOT connect to any other gas type. 2. A 3/4" NPT line is provided at rear for the connection. The unit is equipped with an internal pressure regulator which is set at 4" W.
8 INSTALLATION 1. Uncrate carefully. Report any hidden freight damage to the freight company immediately. 2. Ideally an exhaust system should be direct ly above the appliance to exhaust combustion gases generated by the unit. 3. The appliance is intended for use on noncombustible floors.
9 5.0 OPERATING INSTRUCTIONS FRONT PANEL CONTROLS: Power Switch This switch turns the main power to the unit on and off. It must be turned on to heat the kettle. It should be turned off when the kettle will not be in use for long periods. Thermostat Selects the desired internal kettle operating tem perature.
10 TILTING INSTRUCTIONS Your kettle has the standard “Clean Lock” feature and may not be tilted without disengaging the tilt knob located on the console at the top left. This feature locks the kettle in the upright position and also allows the operator to lock the kettle at 105 degrees for ease of cleaning.
11 6.0 PERIODIC MAINTENANCE All units are adjusted at the factory. In order to avoid problems in operation, check type of gas an d manifold pressure at initial installation and compare it with information on the rating plate. CLEANING The gas fired tilting kettle should be cleaned after each use.
12 GENERAL SERVICE In order to avoid problems, check that the unit has been connected to the gas supply type and voltage for which it was supplied. This can be done by examining the rating plate that lists the gas type and voltage for which the unit was manufactured.
13 counterclockwise. Use the centre of the black ring as an indicator. 6. If relief valve opens, reduce setting on pressure switch, cool kettle completely by filling with cold water and repeat this procedure.
14 7.0 TROUBLESHOOTING Unit does not come on: 1. Power switch and/or thermostat is “OFF”. 2. Unit is not plugged in. 3. Main power supply is off. 4. Tilt micro switch out of alignment or faulty. Unit is on electrically but does not heat: 1. Gas supply to the unit is “OFF”.
15 APPENDIX ‘A’ MATERIAL SAFETY DATA SHEET PREPARATION INFORMATION: Prepared for use in Canada by: E H & S Product Regulatory Management Department DOW CHEMICAL CANADA INC.
16 S HAZARDS IDENTIFICATION EMERGENCY OVERVIEW POTENTIAL HEALTH EFFECTS (See Section 11 for toxicological data.) EYE: May cause slight transient (temporary) eye i rritation. Corneal injury is unlikely. Mists may cause eye irritation. SKIN CONTACT: Prolonged contact is essentially nonirritating to skin.
17 4. FIRST AID EYES: Flush eyes with plenty of water. SKIN: Wash off in flowing water or shower. INGESTION: No adverse effects anticipat ed by this route of exposure incidental to proper industrial handling. INHALATION: Remove to fresh air if effects occur.
18 possibly resulting in spontaneous combustion. Container may rupture from gas generation in a fire situation. EXTINGUISHING MEDIA : Water fog or fine spray, carbon dioxide, dry chemical, foam. Alcohol resistant foams (ATC type) are preferred if available.
19 S EXPOSURE CONTROLS/PERSONAL PROTECTION ENGINEERING CONTROLS: Provide general and/or local exhaust ventilation to control airborne levels below the exposure guidelines.
20 HAZARDOUS DECOMPOSITION PRODUCTS: Hazardous decomposition products depend upon temperature, air supply and the presence of other materials. HAZARDOUS POLYMERIZATION: Will not occur. 11. TOXICOLOGICAL INFORMATION (See Section 3 for Potential Health Effects.
21 local laws and regulations. Regulations may vary in different locations. Waste characterizations and compliance with applicable laws are the re sponsibility solely of the waste generator. THE DOW CHEMICAL COMPANY HAS NO CONTROL OVER THE MANAGEMENT PRACTICES OR MANUFACT URING PROCESSES OF PARTIES HANDLI NG OR USING THIS MATERIAL.
22 U.S. REGULATIONS SARA 313 INFORMATION: To the best of our knowledge, this product contains no chemical subject to SARA Title III Section 313 supplier notification requirements.
23 CANADIAN REGULATIONS WHMIS INFORMATION: The Canadian Workplace Hazardous Materials Information System (WHMIS) Classification for this product is: This product is not a “Controlled Product” under WHMIS.
Ein wichtiger Punkt beim Kauf des Geräts Blodgett KLT-12G (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Blodgett KLT-12G noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Blodgett KLT-12G - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Blodgett KLT-12G reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Blodgett KLT-12G erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Blodgett KLT-12G besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Blodgett KLT-12G verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Blodgett KLT-12G. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Blodgett KLT-12G gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
