Benutzeranleitung / Produktwartung EMX860ST des Produzenten Yamaha
Zur Seite of 24
Owner’s Manual E SEE REAR PANEL CAUTION. POWER PHANTOM +48V ON OFF +6 +3 0 –5 –10 +6 +3 0 –5 –10 • 6 • 0 • 6 • MONI ON LR LR LIMITER LIMITER VOCAL L HALL S HALL L+R BRIDGE STEREO MAI.
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
Important 3 EMX860ST—Owner’s Manual Important Read the Following Before operating the EMX860ST W arnings • Do not allow wate r to ente r this unit or allow the unit t o become w et.
4 Important EMX860ST—Owner’s Manual Operating Notes • The digital circuits of this unit may induce a slight noise into nearby radios and TVs. If noise occurs, relocate the affected equipment. • U sing a mobile telephone near this unit may induce noise.
Introduction 5 EMX860ST—Owner’s Manual Introduction Thank you for pur chasing the Y amaha EMX860ST P owered M ix er . The EMX860ST has the following features.
6 Front and rear panel EMX860ST—Owner’s Manual Front and rear panel Control panel ■ Channel section U se these controls to adjust fact ors such as the equalization, (frequency r esponse), v olume, effect and monitor output level for the input sig- nal to each c hannel.
Control panel 7 EMX860ST—Owner’s Manual ■ DIGIT AL EFFECT section This section allows y ou to turn the built-in digital effect on/off and to select the effect ty pe. 7 Effect select switch Select the effect ty pe for the built-in digital effect.
8 Front and rear panel EMX860ST—Owner’s Manual ■ MONITOR section This section allows y ou to adjust the t one and volume of the MONITOR bus, and specify the mix level of the built-in digital effect. 0 Graphic equalizer The EMX860ST has a 7-band graphic equalizer for adjusting the frequency r esponse of the MONI bus signal.
Control panel 9 EMX860ST—Owner’s Manual ■ POWER AMP section This section allows y ou to select the signals that will be output from the built-in three-channel powe r amplifier , and to select the BRIDGE mode.
10 Front and rear panel EMX860ST—Owner’s Manual Input/output panel 1 Channel input jacks (Hi-Z, Lo-Z) 1–6 These are the input jacks for channels 1–6. By using the P AD switc hes (control panel 6 ) you can connect an y of the jacks to a wide range of sources fr om mics to line level dev ices (synthesiz- ers or rhythm bo x es etc.
Input/output panel 11 EMX860ST—Owner’s Manual 5 AUX IN/T APE IN jacks These are input jacks that allo w the signal from an external device to be added to the MAIN out- put. • AUX IN jacks : Connect these jacks t o the output jacks of an external effects proc essor .
12 Front and rear panel EMX860ST—Owner’s Manual Rear panel 1 SPEAKERS MONITOR jacks Connect monitoring speak ers to these jacks. MONI bus signals adjusted at the MONIT OR section are output fr om these jacks. The SPEAK- ERS MONIT OR A and B jacks are int ernally con- nected in parallel, and output the same signals.
Connections 13 EMX860ST—Owner’s Manual Connections W hen connecting various devices, make sur e the cables and plugs hav e the correct rating . Be sure to use cables designed for the purpose when you c onnect speak ers to speak er jacks. ■ Connecting monitoring speakers Y ou can connect one or two speak ers to the SPEAKERS MONIT OR jacks.
14 Connections EMX860ST—Owner’s Manual ■ Example connections REC OUT T APE IN OUTPUT L LL RR R L (MONO) R MAIN(STEREO) MONITOR AUX IN POWERED MIXER FOOT SW MIC Lo-Z Hi-Z LINE EFFECT OUT INPUT TO.
Basic Operation 15 EMX860ST—Owner’s Manual Basic Operation Connecting microphones and instruments 1 Before connecting mics or instruments, make sure that the power of all equip- ment (where applicable) is turned off.
16 Example setups EMX860ST—Owner’s Manual Example setups This section pro vides some ways in which the EMX860ST can be used, and explains connections and opera- tion. As a conference P A system/installed sound system This example shows the EMX860ST used as a c onfer ence P A system or sound system.
As a conference PA system/installed sound system 17 EMX860ST—Owner’s Manual Playing back a CD player 1 T urn the power on in the order of periph- eral devices ➞ EMX860ST . 2 Adjust the MASTER control of the MAIN section to the √ √ √ √ position.
18 Example setups EMX860ST—Owner’s Manual As a band P A Her e is an example of using the EMX860ST as a small P A for a band. I n this example, an external effect such as delay or r everb is also being used. Connections • Connect mics or instruments, such as k eyboards, to the channel input jacks 1–8.
As a band PA 19 EMX860ST—Owner’s Manual Using an external effect 1 Set the EFFECT section EFFECT OUT con- trol to the √ √ √ √ position. 2 Raise the EFFECT controls for the channels to which you want the external effect to be applied.
20 Troubleshooting EMX860ST—Owner’s Manual T roubleshooting The following table describes the possible malfunctions of this de vice, and the appropriate actions to be tak en in each case. Prob lem Cause Action Sound is no longer out- put from the speakers .
Specifications 21 EMX860ST—Owner’s Manual Speci fi cations ■ General speci fi cations Maximum output po wer MAIN STEREO: 135 W+135 W/8 Ω @0.5% THD at 1 kHz, 200 W+200 W/4 Ω @0.5% THD at 1 kHz MAIN BRIDGE: 400 W/8 Ω @0.5% THD at 1 kHz MONIT OR: 135 W/8 Ω @0.
22 Specifications EMX860ST—Owner’s Manual ■ Input speci fi cations ■ Output speci fi cations • All output jacks are unbalanced. • 0 dB=0.775 Vrms, 0 dBV=1 Vrms. Specifications are subject to c hange without prior notice. *1. Sensitivity is the lo west le v el that can produce an output of +4 dB (1.
Dimensions 23 EMX860ST—Owner’s Manual ■ Dimensions ■ Block and Level diagram 308 16 H:324 16 W:497 D:275 Unit: mm Hi-Z [ – 10dB] LINE [ – 10dB] MAX.
YAMAHA CORPORATION V296250 R0 1 IP 24 Pro Audio Di vision, #18/3 P .O. Box 3, Hamamatsu, 430-8651, Japan Printed in Taiwan.
Ein wichtiger Punkt beim Kauf des Geräts Yamaha EMX860ST (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Yamaha EMX860ST noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Yamaha EMX860ST - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Yamaha EMX860ST reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Yamaha EMX860ST erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Yamaha EMX860ST besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Yamaha EMX860ST verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Yamaha EMX860ST. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Yamaha EMX860ST gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
